Shuttle X70S barebone
Contents
1. X70 Series Quick Guide English MII eee Shuttle French German Quick Guide Front Rear Side View 4 Point Calibration Optional eGalax Touch USR Contoolben x m Run the screen calibration m Touch and hold the center of the target LAS a A eee HI Hi A LEE program and correct 4 point General Getting Dipy Repeat on four corners and the screen will locations on screen with the et ri ee oi adjust automatically panel Click Start All Programs eGalax Touch Configure Utility Dio 4 pk akeri bo maleh deigli m When the 4 points calibration completed press OK to continue Select Tools tab and click i 5 Cleat ard Calbrals sri ae a and do 4 porii 4 Points Calibration Dic Spim beanzeton foe bata bouchscreer Lineaazston iraty De da best bo yey Hest iguh puray Draw Test Safety Information ee ice oe e 2 Read the following precautions before setting up a Shuttle X70 CAUTION 1 Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer CAUTION 2 Do not walk on the power cord or allow anything to rest on it The warranty does not apply to the products that have been disassembled by users Dispose of used batteries according to the manufacturer s instructions Webcam Power LED USB 3 0 Port ss lt COM Port Thermal Vent A Begin Insta2. l life for an easy touch experience Experience A Load lever Place the X70 on a flat surface such as a table Picture 1 and pull the stand the ease of managing your digital life with a few touches gt Follow the steps below to correctly install the CPU into the upwards to an angle of 30 the support bracket can be opened to 60 degrees at The touch of your finger replaces the mouse and is all you need motherboard CPU socket EEE E EE E ere 4 Tighten the HDD amp bracket with one screw most Picture 2 To carry or move your X70 turn back the angle to 0 Picture 3 to interact with the X70 Tare eae th 4 First unlock and raise the socket lever OUCN IETt cliCK ON the MOUSE 9 Screw the ICE module to the mainboard Note to press down on the opposite diagonal corner while tightening each screw Touch and hold right click on the mouse bT an N 10 Fasten the fans with the four screws and connect the Stand Handle F i eel e fan connectors 2 Unscrew four screws of the back cover and remove it C Memory Module Installation de Locate the SODIMM slot on the mainboard 5 Connect the Serial ATA and power cables to the HDD 2 Align the notch of the memory module with the one of the memory slot 5 Lift the metal load plate on the CPU socket Tear off the protective membrane from the bottom of ICE module Remove the protective socket myla
3. llation Microphone Stereo speakers HDMI Port Hom Q Printer Port Optional Power Button 3 Remove the fans and ICE module from the chassis and put them aside 8 Spread thermal paste evenly on the CPU surface J A lt gt i Lep Display Optional Microphone Jack P USB 2 0 Ports COM Ports Optional USB 2 0 Ports lt For safety reasons please ensure that the power Single Multi Non Touch Headphone Line out Jack 2 Clear CMOS Button Stand Handle USB 2 0 Ports lt gt cord is disconnected before opening the case Please note this 1155 pin socket bends easily oS eee Always apply extreme care and little force when i i i e i Hard Disk Drive LED 8 Lan Ports amp Dc in Kensington Lock Port SD Card Reader 1 PE TEE HS caer on EE E UNG O EEE Petaling aie BULROin a ETT Paste application area Metal load plate remove or exchange it Before installation make sure to turn off the computer and unplug the power cord from the mains to avoid damage T r E ee ee ee three screws of the stand mount and remove the stand Placing on the desk How to use the Touch Panel Optional m To place the machine on the desk and to carry it do the following Retention 3 As shown install the HDD amp bracket in the chassis and push it towards the direction as indicated by the red X70 brings digita
4. over complete Notch on eo Cleaning the screen m If you are mounting your X70 to the wall remove the cover the CPU on the back of X70 first cee m Follow these guidelines for cleaning the outside and handling the screen Unscrew three screws of the stand mount and remove the CPU Socket of the computer stand 6 Replace the VESA Base and refasten four screws The VESA standard lets users mount it on to walls easily Please refer to the user guide of the wall arm mount kit you Use a damp or cleaning cloth soft lint free cloth with gentle water only bought to install it and gently wipe the screen surface Note X70 can be mounted to a wall using a VESA Do not spray liquid directly on the screen compatible 100 x 100mm wall arm bracket Turn off the system and disconnect all cables A Please be aware of the CPU orientation DO NOT force the CPU into the socket to avoid bending of pins on the socket and damage of CPU D HDD Installation 1 Unscrew the screw of the bracket and remove it 7 Close the metal load plate lower the CPU socket lever and lock in place 2 Mount HDD into the bracket with four screws Note The product s color and specification will depend upon the actually shipping product 53R X70003 2001
5. r from the CPU socket SODIMM slot Serial ATA Cable B ICE and CPU Installation Serial ATA Power Cable HERE 3 Gently insert the module into the slot in a 45 degree angle Powering on the system m Follow the steps 1 3 below to connect the AC adapter to the DC in jack Press the Power Button to turn on the system Metal load plate 1 Unscrew the four screws of the VESA Base and remove it first Remove the protective membrane E Complete 4 N DCIN 1 Replace the back cover stand and refasten seven screws A DO NOT touch socket contacts To protect the Jy p CPU socket al lace the protecti ket teak oo TE eee ae j i s 45 degree 5 angle NAUN 6 Orientate the CPU and socket and please align the ie vate 1 wen CPU notches with the socket alignment keys Make Button WAS sure the CPU is perfectly horizontal insert it into the socket 4 Carefully push down the memory module until it snaps into the locking mechanism 2 Unscrew the four screws of the the fans and unplug the fan connectors Step 1 then unfasten the four ICE module attachment screws Step 2 Triangle Pin1 Marking on the CPU 5 Repeat the above steps to install additional memory Back Cover modules if required Replace the c
Download Pdf Manuals
Related Search