Da-Lite Large Cosmopolitan Electrol 222"
Contents
1. Up Position Check for power across red and white leads Let motor cool down for 15 minutes Try again Check for continuity Cut off old splice and reconnect Replace motor assembly NOTE Motor is a sealed assembly Replace motor assembly See instructions below See installation instructions See instructions below Adjust up limit switch See installation instructions Replace motor assembly Replace motor assembly LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Da Lite Screen Company LLC warrants its products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If itis necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for2. Turn the down limit switch screw clockwise to decrease the amount of screen drop Run the screen down to test the stop position If the screen drops too far raise the screen about one foot and adjust the limit switch again Repeat until the desired position EGLI UP LIMIT SWITCH ACCESS is set ACCESS HOLE THROUGH CASE OPENING TO INCREASE SCREEN DROP FIGURE 3 Turn the down limit switch screw counterclockwise to increase the amount of screen drop Run the screen down to test the stop position If the screen does not drop enough raise the screen about one foot and adjust the limit switch again Repeat until the desired position is set Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller SETTING THE UP LIMIT POSITION CAUTION Do not allow the slat bar to wrap over the top of the roller when the screen is rolling into the case The screen could be damaged SCREEN TRAVELS INTO CASE TOO FAR Turn the up limit switch screw clockwise to decrease the amount of travel Run the screen up to test the stop position If the screen does not stop properly lower the screen about one foot and turn the limit switch again Repeat until the desired position is set SCREEN DOES NOT TRAVEL FAR ENOUGH INTO CASE Turn the up limit switch screw counterclockwise to increase the amount of up travel Run the screen up to test the stop position If more travel is desired lower the screen about one foot an
3. See Figure 4 for 120V screens or Figure 5 for 220 240V Screens 3 To adjust the down limit switch slide the 3 position switch to the down position Press and hold the down button to run the screen down to the desired stop position Release the button to stop the screen DO NOT PUSH THE STOP BUTTON 4 When the screen is in the desired down position slide the 3 position switch to the off center position The down limit switch is now set 5 To adjust the up limit switch slide the 3 position switch to the up position Press and hold the up button to run the screen up to the desired stop position Release the button to stop the screen DO NOT PUSH THE STOP BUTTON 6 When the screen is in the desired up position slide the 3 position switch to the off center position The up limit Switch is now set 7 To test limit switch setting make sure the 3 position switch is in the off center position Press and release the up or down button on the wall switch to operate the screen 8 Replace switch and cover plate on the wall NOTE If stop button is pressed the wall switch will reverse direction To correct this press the stop button again This will reset the switch You will have to re set both the up and the down settings IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 4 conductor connection that is
4. damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA LITE S WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership Printed in U S A 96652 Rev 3 12
5. the motor in limit set mode Turn the wall switch over and use the down button on front of switch Press and hold until the desired travel position is reached If you travel to far down you can press the up to move the screen upward If you press and let go of either up or down button the motor will do a small jog in that direction for finer adjustment of screen Once desired position is reached turn switch over press and hold down tactile button until the LED on back of switch blinks red twice The down limit is now set 4 To adjust the up limit switch press and hold the up tactile button until the LED on back of switch turns solid green This will put the motor in limit set mode Turn the wall switch over and use the up button on front of switch Press and hold until the desired travel position is reached If you travel to far up you can press the down to move the screen downward If you press and let go of either up or down button the motor will do a small jog in that direction for finer adjustment of screen Once desired position is reached turn switch over press and hold up tactile button until the LED on back of switch blinks green twice The up limit is now set 5 To test limit switch setting press and release the up or down button on the wall switch to operate the screen 6 Replace switch and cover plate on the wall NOTE If the screen is in limit set mode and no buttons are pushed for 20 seconds the LED on the back of the wall switch will
6. E COSMOPOLITAN ELECTROL INSTALLATION FOR SCREENS WITHOUT A BUILT IN LOW VOLTAGE CONTROL Internal wiring has been completed at the factory Installer must route power to the wall switch and to the junction box located on the left end of the screen case See wiring diagram below for wire connections NOTE This screen can only be controlled by a single 120VAC or 240VAC wall switch To use multiple switches an optional low voltage control must be used 120V WIRING DIAGRAM FOR STANDARD WALL SWITCH JUNCTION BOX LOCATED IN EEDA Eu 1 OTE ASINGLE SWITCH CANNOT BE USED TO OPERATE MORE THAN ONE SCREEN CONTACT THE FACTORY FOR FURTHER INFORMATION BLACK DOWN AC COMMON SPDT SWITCH WITH CENTER OFF AC HOT 120VAC 60HZ 1 AMP BLACK YELLOW THIS SWITCH CAN NOT BE USED WITH LVC 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram in wall switch boxes included with screen SCREEN ADJUSTMENT FOR SCREENS WITHOUT A BUILT IN LOW VOLTAGE CONTROL Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory No further adjustment is necessary If you need to make minor stop position adjustments see the appropriate step below SETTING THE DOWN LIMIT POSITION NOTE One turn of the limit screw equals approximately 2 of screen travel TO REDUCE SCREEN DROP
7. The Da Lite Difference NN P3 z lt A 1 a A DA LITE H e DA LITE SCREEN COMPANY LLC Instruction Book for 3100 Norin Dato See ost Office B Warsaw IN 46581 0137 USA LARGE COSMOPOLITAN ELECTROL P 800 622 3737 574 267 8101 F877 325 Tue u 574 267 7804 www da lite c e mail info da lite com IMPORTANT SAFETY INSTRUCTIONS When using your video equipment basic safety precautions should always be followed including the following 1 Read and understand all instructions before using 2 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently 3 The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons SAVE THESE INSTRUCTIONS INSTALLATION Carefully unpack screen and remove outer wrapping from case Remove the black tape and rubber bands from the slat bar after the case has been installed The Large Cosmopolitan Electrol comes with brackets to allow for CASE HOOK wall mount or ceiling mount installations Procedures for each method are as follows oa m ud Wall Mount AMOUNT 1 The wall mount bracket should be fastened to wall studs or some reinforcement within the wall Concrete or brick walls require special fasteners a
8. accessible TROUBLESHOOTING Visit www da lite com products product videos php to find installation and troubleshooting videos and tutorials You will also find a link to Live Chat for interactive support and you can contact us by email at info da lite com or by phone at 800 622 3737 or 574 267 8101 with any troubleshooting questions SYMPTOM 1 Screen will not operate Motor does not hum 2 Incorrect stopping position in downward direction 3 Incorrect stopping position in upward direction 4 Noise NOTE Screen will operate with a low pitched hum 5 Coasting a Blown fuse b Tripped circuit breaker c No power to operating switch or junction Power at junction box d Thermal overload tripped e Broken wire in the down or up position Defective motor limit switch or capacitor Capacitor burned out Lost roller wrap Down limit switch out of adjustment Lost roller wrap Up limit switch out of adjustment a Gear Noise a Defective brake RESTORING LOST ROLLER WRAP 1 Tape a strap to the bottom of the screen surface 2 Push strap over back of roller 3 Feed fabric as you pull strap to draw fabric over top of roller 4 Remove tape and strap 6 CAUSE SOLUTION Replace fuse Reset circuit breaker Check above Tighten all loose wire connections Correct any improper connections Down Position Check for power across black and white leads
9. d adjust the limit switch again Repeat until the desired position is set LARGE COSMOPOLITAN ELECTROL INSTALLATION FOR 120V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL RJ 14 PIN OUTS RJ 22 PIN OUTS 120V WIRING DIAG RAM TAB IS FACING UP TAB IS FACING UP WITH OPTIONAL BUILT IN LOW VOLTAGE CONTROL RJ 45 PIN OUTS TAB IS FACING UP RJ 45 RECEPTACLE RJ 45 JACK FRONT OF BACK OF WALL SWITCH WALL SWITCH POWER WIRE 3 conductor 20 24 gauge wire can be used in place of the supplied RJ 14 cable to connect the wall switch Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch BLACK HOT adjustments EVEN if a third party control system is WHITE COMMON GROUND MUST BE used Therefore it is advised to wire the switch or EL ND FIGURE 4 provide a 3 conductor connection that is accessible POWER INPUT 120VAC 60HZ SCREEN ADJUSTMENT FOR 120v SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL 1 Locate the wall switch and remove the cover plate from the 3 button wall switch and remove the switch from the junction box 2 Locate the two tactile buttons on the back of the switch They are square silver with black round buttons See Figure 4 VPI or Figure 5 LVC for diagram 3 Toadjust the down limit switch press and hold the down tactile button until the LED on back of switch turns solid red This will put
10. nd anchors 2 The wall bracket has holes spaced at 16 and 24 to align with STOP SCREW most wall studs The bracket must be level and plumb Keep in mind you will need at least 2 3 4 between the ceiling and the top of the wall mount bracket to be able to position the case on the bracket 5 Mount the screen case on the wall bracket as shown in figure 1 Be sure the case is fully seated on the bracket CASE HOOK Tighten the stop screws against the wall bracket RENE Ceiling Mount BRACKET m i 5 16x3 4 BOLT 1 Be sure the ceiling has adequate reinforcement to attach the NUT AN a U D screen brackets LOCK WASHER 2 Attach the ceiling brackets to the wall mount bracket using the supplied 5 16 x 3 4 bolts washers and nuts attach with 5 16 bolts not supplied The bolts should be BRACKET ong enough to pass through the drywall or ceiling tile and STOP SCREW penetrate at least 1 1 2 into the reinforcement in the ceiling 4 Mount the screen on the wall bracket as shown in figure 2 Be sure the case is fully seated on the bracket Tighten the stop screws against the wall bracket FIGURE 1 S VIEWING SURFACE AUDIENCE SIDE HHR 3 Position the ceiling bracket assembly on the ceiling and WALL Pe m 4 FIGURE 2 P SURFACE AUDIENCE SIDE LARG
11. turn off the motor will return to run mode and no changes will be saved If this occurs return to step 3 for down limit adjustment or step 4 for up limit adjustment IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible GREEN GROUND LARGE COSMOPOLITAN ELECTROL INSTALLATION FOR 240V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL CONNECT SUPPLIED RJ9 CABLE TO 240V WIRING DIAGRAM SWITCH OR USE 4 WITH OPTIONAL BUILT IN OPTIONALIR AND RF TO CONNECITO LOW VOLTAGE CONTROL REMOTE CONTROL SCREWTERMINALs LOW VOLTAGE WALL SWITCH UP DN GND 45V BLUE COMMON BROWN HOT 240VAC 50HZ GREEN T 3 POSITION SWITCH Rug GROUND MUST BE GREEN C CONNECTED TO BUILDING GROUND GROUND TO CASE DRY CONTACTS ILT RJ9 PIN OUTS IMPORTANT NOTE The wall switch is REQUIRED to make any limit I UE switch adjustments EVEN if a third party control the switch or provide a 4 conductor connection A system is used Therefore it is advised to wire 5V E u gt E Pp that is accessible FIGURE 5 SCREEN ADJUSTMENT FOR 240v SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL 1 Remove the cover plate from the 3 button wall switch and remove the switch from the junction box 2 Locate small 3 position switch on back of wall switch
Download Pdf Manuals
Related Search