Toshiba IK-WD04A surveillance camera
Contents
1. e pr ipa rly connected to a yaur device You n find the e pro r ana then aiko n the Refre sh Devi the ArtD part but device P NOIE f Installation Wizard does not find the camera during the search try turning off the wireless LAN of a PC Installation Wizard can search the location of the Network Camera even though DHCP is not used on the network In this scenario assign the camera a static IP address because the IP address of the Network Camera has been assigned 169 254 by default ON E m Retrieving Images 1 Access the Network Camera from the network 2 Retrieve live video through Internet Explorer TOSHIBA Network Camera Video stream 1 gt Manual trigger PTZ panel Digital v 2012 10 3 10 22 10 ca 2 u e e E Goto Seledone For more information on camera configuration please refer to user s manual on the CD ROM Adjusting the Lens Based on the live image retrieved from the camera adjust the camera lens by performing the following Using an analog monitor This camera is able to output an analog NTSC video signal from the Video Out jack Adjustment of Viewing angle is possible using a portable monitor without using a personal computer when installing Use the included Video Out cable for this purpose To adjust the viewing angle 1 Turn the lens module left and right 2 Loosen the tilt adjustment screws on both side of the camera and then turn the lens mo2. and solid part of the ceiling or wall If installed improperly or on a weak surface the camera could fall causing injury and damage Use Category Cat 5 or higher cable Network Deployment Power over Ethernet PoE e When using a PoE enabled switch The camera is PoE compliant allowing transmission of power and data via single LAN cable See the following illustration to connect the camera to a PoE switch via LAN cable PoE switch not supplied A Client PC not supplied e When using a non PoE switch Use a PoE power injector not supplied to connect between the camera and a non PoE switch PoE power injector not supplied _ _ CS gt Client PC B non PoE switch not supplied not supplied General Connection without PoE 1 Connect the camera to an Ethernet switch via LAN cable 2 Connect the power cable from a power unit not supplied to a power outlet 3 Connect the PC to an Ethernet switch via Ethernet cable Ethernet switch not supplied Client PC not supplied NOTE _ The recommended power supply for this camera is 6 watts minimum When PoE is connected don t supply DC12V Spec of DC plug is mentioned below Assigning IP Address 1 Install the Installation Wizard under the Software Utility directory from the CD ROM 2 The program will analyze your network environment After your network i
3. improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the camera to its normal operation e If the camera has been dropped or the cabinet has been damaged f When the camera exhibiting a distinct change in performance which indicates a need for service g Other trouble 18 Other trouble Replacement Parts When replacing parts be sure the service technician uses parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 19 Safety Check Upon completion of any service or repairs to this camera ask the service technician to perform safety checks to determine that the camera is in proper operating condition Important Safeguards Cont CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL A The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literatur
4. TOSHIBA Leading Innovation gt gt gt NETWORK CAMERA Model IK WD04A Quick Start Guide and Important Safeguards This guide describes the hardware installation Refer to the user s manual PDF file contained in the CD ROM for settings operations and other information The application Adobe Reader is needed to view PDF files If you do not have this application download it from the Adobe Systems Incorporated website E http www adobe com For information on our latest products and peripheral devices refer to the following Website E http www toshibasecurity com If the URL changes refer to the Toshiba website http www toshiba com O 0 ntroduction FCC USA INFORMATION NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interferenc
5. bowl kitchen sink or laundry tub in a wet basement or near a swimming pool 8 Accessories Do not place this camera on an unstable cart stand tripod bracket or table The camera may fall causing serious injury to a person or serious damage to the product Use only with stand tripod bracket or table recommended by the manufacturer or sold with the camera Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer 9 Ventilation This camera should never be placed near or over a radiator or heat register If this product is placed in a built in installation verify that there is proper ventilation so that the camera temperature operates within the recommended temperature range 10 Power Sources This camera should be operated only from the type of power source indicated on the information label If you are not sure of the type of power supply at your location consult your product dealer 11 Power Cord Protection Power cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to cords at plugs screws and the point where they exit the product 12 Installation Install this camera on a secure part of the ceiling or wall If installed on an unsecured location the camera could fall causing injury and damage 13 Lightning For additional protection on thi
6. d 2 Be aware off abie route Q90 Trademarks Microsoft Windows Windows Vista and Internet Explorer are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries Intel and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Other product names appearing in this quick start guide may be trademarks or registered trademarks of their respective holders Note TOSHIBA AMERICA INFORMATION SYSTEMS INC Surveillance amp IP Video Products 9740 Irvine Boulevard Irvine CA 92618 1697 Phone Number 877 855 1349 625019500G
7. dule up and down Upon completion tighten the screws 3 Turn the lens cover to adjust the image orientation Pan 350 Tilt 70 Rotate 340 DO NOT over rotate the lens Doing so will damage the camera lens module O 0 Adjusting the Zoom and Focus To adjust the zoom factor and focus range 1 Loosen the zoom controller and then adjust zoom factor by moving the controller left and right Upon completion tighten the zoom controller screw 2 Loosen the focus controller and then adjust focus range by moving the controller left and right Upon completion tighten the focus controller screw LT g igo i es er Sie RES Zoom Controller re TS Focus Controller Completion 1 Align the inner side of the black cover with the notches on both sides of the lens fix the black cover Note The black cover cannot be attached if installed in the wrong orientation 2 If you choose to feed the cable through the ceiling wall arrange the cable neatly through the cable hole If you choose to feed the cable from the side remove plate B 3 Attach the dome cover to the camera as shown below The dome cover cannot be attatched if installed in the wrong orientation Align the side cover or side cutout with where the cable comes out from the camera Push the dome cover to join with the camera 4 Finally make sure all parts of the camera are securely installe
8. e accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE FIELD INSTALLATION MARKING WORDED THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES This product is intended to be supplied by a Listed Power Adapter with LPS rated 12V DC 0 23A minimum or 48V DC 0 07A for POE minimum O 0 Notes on Use and installation Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear A vertical stripe may appear on the screen However this is not a malfunction Treat the camera with care Dropping or subjecting the camera to intense vibration may cause it to malfunction Never touch internal parts Do not touch the internal parts of the camera other than the parts specified Keep the camera installation away from video noise If cables are wired near electric lighting wires or a TV set noise may appear in images In this event relocate cables or reinstall equipment Check the ambient temperature and humidity Avoid using the camera where the temperature is hotter or colder than the specified operating range Doing so could affect the internal parts or cause the image quality to deteriorate Special care is required to use the camera at high temperature a
9. e by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with emission limits USER INSTALLER CAUTION Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party Thank you for purchasing the IK WDO4A Network Camera Before using the camera read this quick start guide carefully to ensure correct usage After reading this quick start guide save it for future reference The design specifications software and quick start guide contents are subject to change without prior notice Terms The term OS is used in this manual to indicate operating systems compatible with this product Microsoft Windows XP xxxx Edition Microsoft Windows Vista Business Edition Microsoft Windows 7 Professional Edition f NOTE _ The performance of the network camera may vary depending on the network environment Table of Contents TM le IUT OW PE E AO 2 FCC USA EINFORMATIONSE en pinnin ei ia aneii mnt 2 SR a en ananas binatansuntditantd mag eieasaniaueas E E E iia 3 Table of COMING oo snsacgacecusesteab
10. eacnnsssneledeeuinatedeeexassansese 4 Important SafeguardS me ane teens emeee cette cessent 9 Important Safeguards Cont T Notes on Use and Installation 8 Setting the Network Camera Environment 9 Items needed for network camera monitoring 9 OE ee eee ne eR rc Oe te Rm en oN ere een ee 10 Physical OSCE OUOM nee de ot ee dois 11 hardware OS ANAIORS da 12 INGTON IC OIC RON and ae ae RNE 15 Assigning IP AO GIGS ct czencieacscctovacnesanicaemsvsbeunsccsandneushexeinaspcretioneancesunereateeachaes 17 Retrieving AMA LEE 18 Adjusting the LC INS ennemi cit tion 0 19 Adjusting the Zoom and FOCUS ovis ic scaaceassaxnccanchiemnensnaa sersaasbivdasbbansietaueanensanioines 20 See Ee a een meee ero nee Sp E eng eee 21 MNCS VAT S a octets 22 O 0 mportant Safeguards 1 Read Instructions Read all the safety and operating instructions before operating the product 2 Retain Instructions Retain the safety instructions and user s manual for future reference 3 Warnings Comply with all warnings on the product and in the user s manual 4 Follow Instructions Follow all operating and use instructions 5 Cleaning Disconnect this camera from the power supply before cleaning 6 Attachments Do not use attachments not recommended by the camera manufacturer as they may pose safety risks 7 Water and Moisture Do not use this camera near water Some examples are near a bath tub wash
11. nd humidity Should you notice any trouble If any trouble occurs while you are using the camera turn off the power and contact your dealer If you continue to use the camera when there is something wrong with it the trouble may get worse and an unpredictable problem may occur Setting the Network Camera Environment Items needed for network camera monitoring Administrator s personal computer The personal computer that allows setting operating monitoring and other functions with the network camera is called the administrator s personal computer in this guide The personal computer for viewing monitored images is called the user s personal computer in this quick start guide The network camera can be viewed by more than one personal computer at the same time Recommended personal computer system requirements Windows XP Windows Vista Business or Windows 7 professional Internet Explorer Ver 8 0 CPU Intel Core 2 Duo 2GHz or greater Memory 1GB RAM or greater Connection equipment such as LAN cables and switch or router The LAN cable type differs depending on the connection method Camera search application Installation Wizard Install this application from the CD ROM supplied as an accessory Double click Setup exe in the CD ROM and install the application by following the onscreen instructions This application is the tool to discover the IP address of a camera Using
12. s analyzed please click on the Next button to continue the program ee G Installation Wizard Network Type Q Installation Wizard Network Type Installation Wizard Installation Wizard Your network environment was analyzed as below No connection to Internet izard is analyzing your network environment g wait a moment Installation Wizard Cable DSL modem 3 The program searches for other Network Cameras on the same network 4 After searching the main installer window will pop up Double click on the MAC address of the appropriate device to connect to the Network Camera Tr q Installation Wizard x Device Selection i i Installation Wizard Select a device to setup or upgrade 7 mac __IP Address Model Setu 00 02 D1 71 42 70 169 254 0 99 IK WR12A TOSHIBA NETWORK CAMERA Rares MODEL No IK WD04A c US DC12V 0 23A 000201714270 This device complies with Pa iie of the FCC Rules Operatio LISTED is subject to the following two conditions 1 this device ay not cause h om interfere and 2 tie Ha w must accept 38KG any interfere received il Ea idin ng interfer that may cause E324690 undesired paral CAN ICES 3 B NMB 3 B S N __A1010XXXX MAC 0002D1XXXXXX TOSHIBA CORPORATION ene TILL FABRIQUE EN FORMOSE ee em ind your device in the wees ee ease make sure all
13. s camera during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the power supply and cable system This will prevent damage to the camera due to lightning and power line surges If lightning occurs do not touch the unit or any connected cables in order to avoid electric shock 14 Overloading Do not overload the power supply or extension cords as this can result in a risk of fire or electric shock 15 Object and Liquid Entry Never push objects of any kind into this camera through openings as they may touch dangerous electrical points or short out parts that could result in a fire or electrical shock Never intentionally spill liquid of any kind on the camera 16 Servicing Do not attempt to service this camera yourself as opening or removing covers may expose you to dangerous electrical or other hazards Refer all servicing to qualified service personnel 17 Damage Requiring Service Disconnect this camera from the power supply and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the camera c If the camera has been submerged in water d If the camera does not operate normally by following the operating instructions in the user s manual Adjust only those controls that are covered by the user s manual as an
14. ter onto the cable to prevent EMI radiation The clamp filter uld be installed e at least 5cm a m the camera A 5 cm Cable Tie Notes The included screws and anchors are used to install the Wall Mount camera to a solid surface e g concrete If installing on loose or thin material surfaces use the appropriate anchors not included with the screws f possible point the TOSHIBA logo towards the field of view The adjustment range of PAN is indicated on the alignment sticker Install the camera securely Mounting the camera to a solid surface 1 Attach the Alignment Sticker to the surface 2 Drill two pilot holes 0 20inchx0 99inches D O95mmX25mm D through the two circles on the sticker 3 Hammer the supplied plastic anchors into the holes 4 Drill a cable hole A 1 1inch O 28mm as shown in the above picture and lead the cables through this hole 5 Align the two mounting holes of the Camera with the two plastic anchors insert the included two screws to the corresponding holes and tighten them with a driver Cable installation If possible lead all cables behind the camera body through a wall or ceiling If this is not possible use the knock out on the camera cover to route the cables through the side Please refer to Completion on page 21 ff CAUTION Installation should be done only by qualified personnel and conform to all local codes Install this camera on a firm
15. this application the IP address of a camera can be easily determined Q 0 Contents IK WDO4A O CD ROM NETWORK CAMERA IK WDO4A TOSHIBA z fn a a Warranty Card 7 Clamp Filter ee Video Out Cable Alignment Sticker Drill hole A a Cable hole r a S Alignment Sticker o 4 CA cca Drill hole K Quick Start Guide and Important Safeguards TOSHIBA Leading Innovation gt gt gt NETWORK CAMERA Model IK WD04A Quick Start Guide and Important Safeguards Screws and Anchors RJ45 Female Female Coupler Physical Description General I O Terminal Block a Digital Input GND Black Cover General 1 0 Terminal Block 10 100BaseT Ethernet e RJ45 Plug Power Cord Socket Reset Button Status LED MicroSD SDHC Card Slot Video Out Connector 2 pins O20 x Hardware Installation First follow the instructions below to remove the dome cover Flip the black retention tabs in the counter clockwise direction to release the dome cover clockwise if you look from the bottom up Dome Cover Record the MAG address before installing the camera gt MAC 0002D1XXXXXX Then remove the black cover as shown below Tilt Adjustment Screws Y C 4 F Lens Cover Mounting hole Buckle the supplied clamp fil
Download Pdf Manuals
Related Search