APC Smart-UPS RC 96V Battery Pack
Contents
1. with six 48 V battery modules 15 kg 32 Ibs 75 kg 164 Ibs each 48 V battery module 10 kg 22 Ibs 48 V battery modules Each 96 V battery string consists of two su0265a Maximum number of external battery packs 10 XLBPs supported by Smart UPS RC Combined weights of UPS and all XLBPs installed in a rack must not exceed rack weight limits Dimensions Length x Width x Height 48 cm 19 in x 43 cm 17 in x 18 cm 7 in SRC96XLBP SRC96XLBP2S User Manual Installation Units may vary in appearance from those depicted in this manual Always place UPS above XLBPs in rack mount configuration Connect all battery strings Failure to do so may cause equipment damage Refer to Physical Specifications in this manual and the Safety Guide before installing unit Unit is heavy Batteries must be removed from unit prior to installation 1 Remove screws securing battery compartment door Remove door 2 Grasp plastic flap attached to battery and pull to remove battery module Units in tower configuration remove batteries at top of unit first el II p l _ ep IL 4 o su0223a su0224a P ai w a L P ai Tower configuration Install stabilizer brackets 1 Stabilizer brackets must be installed on tower units 2 Each bracket must be secured with two flat head screws supplied NOTE Screws are pre installed on left side of unit These screws must b2. ES APC WARRANTIES EXTEND ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES IN NO EVENT SHALL APC ITS OFFICERS DIRECTORS AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT SPECIAL CONSEQUENTIAL OR PUNITIVE DAMAGES ARISING OUT OF THE USE SERVICE OR INSTALLATION OF THE PRODUCTS WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT IRRESPECTIVE OF FAULT NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES SPECIFICALLY APC IS NOT LIABLE FOR ANY COSTS SUCH AS LOST PROFITS OR REVENUE LOSS OF EQUIPMENT LOSS OF USE OF EQUIPMENT LOSS OF SOFTWARE LOSS OF DATA COSTS OF SUBSTITUENTS CLAIMS BY THIRD PARTIES OR OTHERWISE NO SALESMAN EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY WARRANTY TERMS MAY BE MODIFIED IF AT ALL ONLY IN WRITING SIGNED BY AN APC OFFICER AND LEGAL DEPARTMENT Warranty claims Customers with warranty claims issues may access the APC customer support network through the Support page of the APC Web site www apc com Select your country from the country selection pull down menu Open the Support tab at the top of the Web page to obtain contact information for customer support in your region SRC96XLBP SRC96XLBP2S User Manual 16
3. Smart UPS RC External Battery Pack Tower Rack Mount 4U SRC9Y6XLBP SRCY6XLBP2S English 990 3486A 01 2009 Introduction Overview The American Power Conversion APC SRC96XLBP external battery pack XLBP connects to an APC Smart UPS RC Together these units provide extended protection for electronic equipment load from utility power blackouts brownouts sags and surges The UPS and the XLBP together provide continuous power from the batteries until utility power returns to safe levels or the batteries are fully discharged Inventory Read the Safety Guide before installing the unit Inspect the battery pack upon receipt Notify the carrier and dealer if there is damage The packaging is recyclable save it for reuse or dispose of it properly Check the battery pack package contents External Battery Pack XLBP e Literature kit containing Front bezel Product documentation a brackets Smart UPS RC User Manuals CD connector cable Hardware supplied listed in table below Safety information Warranty information NOTE The model and serial numbers are located on a small rear panel label For some models an additional label is located on the chassis under the front bezel Hardware supplied Rack mount configuration Pan head screws for securing rack mount brackets to unit Rack mount configuration Washers for securing rack mount brackets to unit K Tower configuration A amp Flat head screws fo
4. attery Strings Factory Default UPS internal battery string 1 for all Models SRC96XLBP2S UPS internal battery string 1 SRC96XLBP2S 2 UPS internal battery string 1 SRC96XLBP2S 3 1 SRC004 1 additional battery string UPS internal battery string 1 SRC96XLBP2S 4 2 SRC004 2 additional battery strings SRC96XLBP The formula for configuring SRC96XLBP units is as follows of battery UPS internal battery string 3 x the number of SRC96XLBP units strings to be entered UPS internal battery string 1 SRC96XLBP 4 UPS internal battery string 2 SRC96XLBP units 7 UPS internal battery string 3 SRC96XLBP units 10 Smart UPS SRC UXI Models Configure Number of Battery Strings Each 96 V battery string consists of two 48 V battery modules Count the number of battery strings being used and enter that number Configuration of Battery Strings Factory Default No UPS internal battery string 0 for all Models SRC9I6XLBP2S 1 SRC96XLBP2S 1 1 SRC96XLBP2S 1 SRC004 1 additional battery string 2 1 SRC96XLBP2S 2 SRC004 2 additional battery strings 3 SRC96XLBP The formula for configuring SRC96XLBP units is as follows of battery 3 x the number of SRC96XLBP units strings to be entered 1 SRC96XLBP 3 2 SRC96XLBP units 6 3 SRC96XLBP units 9 SRC96XLBP SRC96XLBP2S User Manual 13 Contact Information APC Worldwide Customer Support Customer support for this or any other APC p
5. e removed from unit and used to secure stabilizer bracket Screws for securing stabilizer bracket to right side of unit are included in hardware bag supplied with unit su212a SRC96XLBP SRC96XLBP2S User Manual Install and connect batteries This unit is equipped with battery modules Install batteries into unit beginning with batteries at the bottom Each string must be connected to battery connectors on chassis 1 Install batteries su0225a 2 Connect batteries 3 Replace battery compartment door and secure door with screws previously removed su0213a Install bezel 1 Fit three tabs on the bottom inside edge of bezel into slots in chassis 2 Tip bezel forward Fit two tabs on top inside edge of bezel into slots in chassis and snap bezel into position su0216a 2 post rack mount configuration This unit is intended for installation in a 19 two post or four post rack For details on 4 post rail and rack installation refer to instructions in rail kit Remove stabilizer brackets if they are installed Remove four screws that secure each bracket SRC96XLBP SRC96XLBP2S User Manual 6 Position unit for mounting in rack The unit is heavy Use caution when positioning unit NOTE The holes for securing rack mount brackets are plugged Remove the appropriate plugs prior to installing brackets on the unit Install rack mount brackets Four pan head screws and four washers must be used t
6. erved Reproduction in whole or in part without permission is prohibited APC the APC logo Smart UPS and PowerChute are trademarks of American Power Conversion Corporation All other trademarks product names and corporate names are the property of their respective owners and are used for informational purposes only SRC96XLBP SRC96XLBP2S User Manual 15 Two Year Warranty The limited warranty provided by American Power Conversion APC in this statement of Limited Factory Warranty applies only to products you purchase for your commercial or industrial use in the ordinary course of your business Terms of warranty APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase The obligation of APC under this warranty is limited to repairing or replacing at its sole discretion any such defective products This warranty does not apply to equipment that has been damaged by accident negligence or misapplication or has been altered or modified in any way Repair or replacement of a defective product or part thereof does not extend the original warranty period Any parts furnished under this warranty may be new or factory remanufactured Non transferable warranty This warranty extends only to the original purchaser who must have properly registered the product The product may be registered at the APC Web site www apc com Exclusions APC shall not be liable under the war
7. hip it to APC in the Service If the unit requires service do not return it to the dealer Follow these steps 1 Review the problems discussed in Troubleshooting in the UPS manual to eliminate common problems 2 Ifthe problem persists contact APC Customer Support through the APC Web site www apc com Note the model number of the unit the serial number located on the back of the unit and the date purchased If you call APC Customer Support a technician will ask you to describe the problem and attempt to solve it over the phone If this is not possible the technician will issue a Returned Material Authorization Number RMA If the unit is under warranty repairs are free Procedures for servicing or returning products may vary internationally Refer to the APC Web site for country specific instructions 3 Pack the unit in its original packaging If this is not available Pack the unit carefully to avoid damage in transit Never use Styrofoam beads for packaging Damage sustained in transit is not covered under warranty 4 Always DISCONNECT THE UPS BATTERY before shipping in compliance with U S Department of Transportation DOT and IATA regulations The battery s may remain in the unit Mark the RMA on the outside of the package Return the unit by insured prepaid carrier to the address given to you by Customer Support Entire contents copyright 2008 American Power Conversion Corporation All rights res
8. o secure OL each rack mount bracket to unit x4 E It it E Secure 2 post rack to floor su0248a Install units in rack The UPS and XLBPs should be installed at or near bottom of rack Always place the UPS above XLBPs Batteries must be removed from units prior to installation in a rack Two screws not supplied must be used to secure each rack mount bracket to rack yo Sa a Ul SRC96XLBP SRC96XLBP2S User Manual 7 Install and connect batteries This UPS is equipped with battery modules Each module must be connected to battery connectors on chassis 1 Install batteries 2 Connect internal batteries x x2 x2 3 Replace battery compartment door and secure door with screws previously removed Install bezel 1 Fit three tabs on inside edge of bezel into slots in chassis 2 Tip bezel toward chassis Fit two tabs on inside edge of bezel into slots in chassis and snap bezel into position su0226a EFS su0218a su0220a SRC96XLBP SRC96XLBP2S User Manual Connect XLBPs to UPS Tower configuration su221a Rack mount configuration There is small cover over each external battery pack connector on the UPS and XLBP Remove the screw that secures the cover and remove the cover su264a SRC96XLBP SRC96XLBP2S User Manual 9 Configure UPS parameters This configuration affects the accuracy of the predicted runtime calculations the UPS performs while r
9. ontrol none Click OK in each of two windows Press ENTER Configure the number of battery strings using UPS terminal mode 1 Once the blank terminal window is open follow these steps to enter the number of battery strings NOTE Letter key commands are case sensitive Use capital letters when using letter key commands 2 Press Y The UPS will respond with SM in the command box If the UPS does not respond to the Y command ensure the serial cable is securely connected to the serial port on the UPS Use only an APC supplied serial cable When SM appears in the command box press the gt key The UPS will respond with the number of battery strings connected to the UPS If the UPS has not been previously programmed to recognize the number of battery strings this number will be zero Use the or keys to change the number of battery strings OK will appear in the command box Press gt key The number of battery strings will appear in the command box NOTE The or keys and the gt key must be used again to change the number of battery strings from this point in the programming Press R The UPS will respond with BYE in the command box SRC96XLBP SRC96XLBP2S User Manual 12 Smart UPS SRC XLI Models Configure Number of Battery Strings Each 96 V battery string consists of two 48 V battery modules Count the number of battery strings being used and enter that number Configuration of B
10. r securing stabilizer brackets unit Rack mount configuration brackets K 5 Tower configuration stabilizer brackets su0211a Accessories Install accessories prior to connecting power to the UPS Refer to the APC Web site www apc com for available accessories Optional accessories e Additional external battery packs XLBP e Additional battery strings e 4 post rail kit SRC96XLBP SRC96XLBP2S User Manual 3 Specifications Environmental Specifications Temperature Operating 0 to 40 C 32 to 104 F Storage 15 to 30 C 5 to 86 F charge UPS battery every six months 30 to 70 C 86 to 158 F charge UPS battery every three months Maximum Operating 3 000 m 10 000 ft Elevation Storage 15 000 m 50 000 ft Humidity 0 to 95 relative humidity non condensing This unit is intended for indoor use only Select a location sturdy enough to handle the weight Do not operate unit where there is excessive dust or temperature or humidity are outside specified limits Environmental factors impact battery life High temperatures poor utility power and frequent short duration discharges will shorten battery life Physical Specifications Weight Refer to Safety Guide supplied with this unit for lifting guidelines XLBP model SRC96XLBP2S e without batteries e with two 48 V battery modules 15 kg 32 Ibs 35 kg 76 lbs SRC96XLBP e without batteries e
11. ranty if its testing and examination disclose that the alleged defect in the product does not exist or was caused by end user or any third person misuse negligence improper installation or testing Further APC shall not be liable under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage or connection inappropriate on site operation conditions corrosive atmosphere repair installation start up by non APC designated personnel a change in location or operating use exposure to the elements Acts of God fire theft or installation contrary to APC recommendations or specifications or in any event if the APC serial number has been altered defaced or removed or any other cause beyond the range of the intended use THERE ARE NO WARRANTIES EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE OF PRODUCTS SOLD SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH APC DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE APC EXPRESS WARRANTIES WILL NOT BE ENLARGED DIMINISHED OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF APC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC SOLE LIABILITY AND PURCHASER EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTI
12. roduct is available at no charge in any of the following ways e Refer to the APC Web site to access documents in the APC Knowledge Base and to submit customer support requests www apc com Corporate Headquarters Connect to localized APC Web sites for specific countries each of which provides customer support information www apc com support Global support searching APC Knowledge Base and using e support e Contact an APC Customer Support center by telephone or e mail Local country specific centers go to www apc com support contact for information Contact the APC representative or other distributor from whom you purchased your APC product for information on how to obtain local customer support SRC96XLBP SRC96XLBP2S User Manual 14 Maintenance Transport and Service Replace battery modules This UPS has easy to replace hot swappable battery modules Replacement is a safe procedure isolated from electrical hazards You may leave the UPS and connected equipment on during the replacement procedure Once the batteries are disconnected the connected equipment is not protected from power outages Refer to the appropriate replacement battery user manual for battery module installation instructions See your dealer or contact APC at www apc com for information on replacement battery modules replacement battery packing material Pb Pb N Be sure to deliver the spent battery s to a recycling facility or s
13. s ENTER to initiate terminal mode Press ENTER multiple times until the prompt User Name is displayed Follow the prompts Type slowly waiting until each character appears on the screen prior to typing the next character Network Management Card defaults e User Name ape e Password ape Press 1 and ENTER to select Device Manager Select the model by entering the corresponding number then press ENTER Press 3 and ENTER to select Configuration Press 1 and ENTER to select Battery Press 2 and ENTER to change Battery Settings Type in the number of battery strings then press ENTER Press 3 and ENTER to accept the changes Press ESC five times to return to the main menu 10 Press 4 and ENTER to log out SRC96XLBP SRC96XLBP2S User Manual 11 Configure UPS connection settings using UPS terminal mode Connect the serial cable to the serial port on the back of the UPS If using USB communication to the UPS disconnect USB cable prior to connecting serial cable l m gt Open a terminal program such as HyperTerminal From the Desktop go to Start Programs Accessories Communication HyperTerminal Follow the prompts to choose a name and select an icon Disregard the message must install a modem if it is displayed Click Cancel Go to File Properties Select the COM port that is connected to your UPS The port settings are bits per second 2400 data bits 8 parity none stop bit 1 flow c
14. unning on battery power Refer to the Battery String Configuration tables at the end of this section for detailed instructions Smart UPS RC models must be programed to recognize the number of battery strings connected to the UPS There are four options available for configuring the UPS to recognize the number of battery strings 1 PowerChute Business Edition Refer to the instructions included with the software 2 Network Management Card NMC Web interface Refer to the instructions included with NMC 3 Network Management Card NMC terminal mode Refer to the instructions below 4 UPS terminal mode Configure UPS connection settings using NMC terminal mode Connect the serial cable to the serial com port on rear side of UPS 1 Open a terminal program such as HyperTerminal From the Desktop go to Start Programs Accessories Communication HyperTerminal 2 Follow the prompts to choose a name and select an icon If the message must install a modem click Cancel 3 Go to File Properties Select the COM port that is connected to your UPS The port settings are bits per second 2400 data bits 8 parity none stop bit 1 flow control none gt Click OK in each of two windows 5 Press ENTER to initiate connection to UPS SRC96XLBP SRC96XLBP2S User Manual 10 Configure the number of battery strings using NMC terminal mode 1 2 Cm NA D Once the blank terminal window is open Pres
Download Pdf Manuals
Related Search