Edimax GS-1008P network switch
Contents
1. NETWORKING PEOPLE TOGETHER ES 1008PH ES 1008P GS 1008PH GS 1008P Ouick Installation Guide 07 2012 v1 0 2 DI NETWORKING PEOPLE TOGETHER COPYRIGHT Copyright Edimax Technology Co Ltd all rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission from Edimax Technology Co Ltd Edimax Technology Co Ltd makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Edimax Technology Co Ltd reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes The product you have purchased and the setup screen may appear slightly different from those shown in this QIG The specification is subject to change without notice Please visit our web site www edimax com for the update All brand and product names mentioned in this manual are trademarks and or registered trademarks of their respective holders Edimax Technology Co Ltd Add No 3 Wu Chuan 3rd Rd Wu Ku Industrial Park New Taipei City Taiwan Tel2. 886 2 77396888 Email sales edimax com tw PRODUCT INTRODUCTION Model no ES 1008PH 8 Port Fast Ethernet Switch with 4 PoE Ports ES 1008P 8 Port Fast Ethernet PoE Switch GS 1008PH 8 Port Gigabit Ethernet Switch with 4 PoE Ports GS 1008P 8 Port Gigabit Ethernet PoE Switch Package Contents Before you start using this switch please check if there is anything missing in the package and contact your dealer to claim the missing item s PoE switch x 1pcs O Quick installation guide x 1pcs O Power cord x 1pcs O Rubber feet x 4pcs O Rack mount brackets and screws x 1 set Front Panel Please refer to the following description for the front panel GS 1008P LED Definitions LED Name Light Status PWR On Switch on and correctly powered Off Switch not powered or not correctly powered Port is connected LINK ACT Port is not connected Flashing Port is active and transferring receiving data POE on PoE on and powering PoE PoE Off PoE is not activated Back Panel 100 240 VAC 50 60Hz Power Connector Plug in the female connector of the provided power cord into this connector and the male into a power outlet Supported input voltages range from 100 240V AC and 50 60 Hz Product Specifications Model ES 1008PH ES 1008P GS 1008PH GS 1008P IEEE 802 3 10BaseT IEEE 802 3u 100BaseTX IEEE 802 3ab 1000BaseT IEEE 802 3af 802 3at PoE IEEE 802 3x Flow Control IEEE 802 3az Energy Efficient Ether
3. erference in which case the user may be required to take adequate measures CE FE C DIMAX NETWORKING PEOPLE TOGETHER Edimax Technology Co Ltd Edimax Technology Europe B V Edimax Computer Company No 3 Wu Chuan 3rd Road Wu Gu Nijverheidsweg 25 5683 CJ Best 3350 Scott Blvd Bldg 15 Santa Clara New Taipei City 24891 Taiwan The Netherlands CA 95054 USA www edimax com
4. ment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC Caution This device and its antenna must not be co located or operating in conjunction with any other antenna or transmitter This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment CE Mark Warning This is a class B product In a domestic environment this product may cause radio int
5. net IEEE 802 3 10BaseT IEEE 802 3u 100BaseTX Standards IEEE 802 3af 802 3at PoE IEEE 802 3x Flow Control IEEE 802 3az Energy Efficient Ethernet RJ 45 8 ports 8 ports 8 ports 8 ports Interface PoE 4 ports 8 ports 4 ports 8 ports MAC Address 8K 1K Buffer Memory 128KB 96KB Jumbo Frames 9KB N A Power budget 80W 150W 80W 150W Power Consumption 5 Watts Max Dimensions 266 x 184 x 44 x W x H Weight 1 95 kg Operating Temperature 0 to 50 C Storage Temperature 40 to 70 C Humidity Operating 10 to 90 RH non condensing 1 PRODUCT INSTALLATION There are two ways to install your switch please select one that suits you 2 Desktop Installation 1 Install the switch on a level surface that can support the weight of the unit and the relevant components and attach the rubber feet to the bottom The rubber feet cushion the switch and helps protect the case from scratches 2 Plug the switch into an electrical source with the provided power cord 3 Rack Mount Installation Rack mounting allows for a more orderly installation when a series of network devices is being installed 1 Disconnect all the cables from the switch 2 Place the unit the right way up on a hard flat surface with the front facing you 3 Position a mounting bracket over the mounting holes on one side of the unit 4 Insert the screws and fully tighten with a suitable screwdri
6. ver 5 Repeat the two previous steps for the other side of the unit 6 Insert the unit into the rack and secure with suitable screws 7 Reconnect all the cables Regarding the installation environment we strongly recommend 1 The switch should be placed in an appropriately ventilation environment A minimum 25 mm space around the unit is recommended 2 The switch and the relevant components should be kept away from sources of electrical noise such as radios transmitters and broadband amplifiers 3 Avoid environments with higher than recommended moisture levels Troubleshooting 1 Power LED is not lit Check if the power cord is properly connected to the plug and the power outlet make sure the power cord is firmly plugged into the power socket of the switch 2 LINK ACT LED is not lit when connected to devices Make sure the network device attached to the switch is turned on Make sure the network cable is properly connected to the switch and the network device Make sure the network cable is a UTP cable that complies with EIA TIA 568 and Category 5 specifications Contact your dealer if problems persist Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equip
Download Pdf Manuals
Related Search