Antec CS-52553CB computer case
Contents
1. standoffs with the provided Philips head screws Your motherboard is now installed QE Connecting the Power and LED 1 Connect the Reset switch labeled RESET SW to your motherboard at the RST connector 2 Connect the Power LED labeled POWER LED connector to the PWR LED connector on the motherboard 2 3 Connect the Power Switch labeled POWER SW to the PWR connector on the motherboard 4 Connect the Hard Drive LED labeled H D D LED to the HDD LED connector on the motherboard Connecting the USB Ports Note Please check your motherboard manual for your USB header pin layout and make sure it matches the attached table If it does not match this Intel standard please call Antec customer support at 800 22ANTEC North America or at 31 0 10 462 2060 Europe to buy a USB adapter SKU 30095 This adapter will allow you to connect the top USB to your motherboard on a pin by pin basis Motherboard Pin Layout Pin Signal Names Pin Signal Names USB Power 1 USB Power 2 Negative Signal 1 Negative Signal 2 OO0O0UF OOUOOOOR Positive Signal 1 6 Positive Signal 2 o 7 Ground 1 8 Ground2 9 Key No Connection Empty Pin Connecting the IEEE 1394 FireWire i Link Port Note Please check your motherboard manual for your IEEE 1394 header pin layout and make sure it matches the attached table If you intend to connect the front FireWire port to an IEEE 1394 add on card that comes with an external2. type IEEE1394 connector please call Antec customer service at 800 22ANTEC North America or 31 0 10 462 2060 Europe to buy an adapter SKU 30031 This adapter will allow you to connect the top IEEE 1394 port to the external type connector CO O Pin Assignment for Front Panel IEEE 1394 Connector Fin Signal Names Pin Signal Names OOO0UF OOUOOOOR EE re 12V Fused 8 12V Fused Ta ey No Pin CO O Connecting the Audio Ports For a non Intel standard audio connection you will need to plug the 7 individual connectors onto the motherboard as follows Locate the internal audio connectors from your motherboard or sound card Consult your motherboard or sound card manual for the pin out positions 1 Microphone Signal Pin Connect the MIC connector to this pin 2 Microphone Power Connect the MIC BIAS connector to this pin 3 Ground Pin Connect the AUD GND connector to this pin 3 Front Right Speaker Out Pin Connect the FROUT R connector to this pin Front Left Speaker Out Pin Connect the FPOUT L connector to this pin Rear Right Speaker Out Pin Connect the RET R connector to this pin Rear Left Speaker Out Pin Connect RET L connector to this pin NO O1 R Flexi Drive Bay System The Nine Hundred comes with nine 5 25 external drive bays at the front of the case There are two HDD cages preinstalled inside the bottom six 5 25 bays Each HDD cage occupies three consecutive 5 2
3. 00mm TriCool fan This fan has a three speed switch that lets you choose the speed best suited to your needs The default setting is Low The Front TriCool fans Nine Hundred comes with two 120 x 25mm TriCool blue LED fans which are pre installed in front of each HDD cage to cool the hard drives These fans are installed so the air will be blown into the case The Rear Exhaust TriCool Fan There is a 120 x 25mm TriCool fan preinstalled at the rear of the case The fan is installed so the air will be blown out of the case 200mm Fan Specifications Size 200 x 30mm TriCool Fan Rated Voltage 12V DC Operating Voltage 10 8V 13 2V Speed Input Static Acoustical Input Current Pressure Noise Power High 0 3A 3 80 m min 0 69 mm H20 30 dBA 3 6 W 800 RPM 134 CFM 0 03 inch H20 Medium 0 17A 3 07 m min 0 40 mm H20 27 dBA 2 04 W 600 RPM 108 CFM 0 02 inch H20 Low 0 08A 2 34 m min 0 20 mm H20 24 dBA 1 0 W 400 RPM 83 CFM 0 01 inch H20 120mm Fan Specifications Size 120 x 25mm TriCool Fan Rated Voltage 12V DC Operating Voltage 10 2V 13 8V Speed Input Static Acoustical Input Current Pressure Noise Power High 0 24A 2 24 m min 2 54 mm H20 30 dBA 2 9 W 2000 RPM Max 79 CFM 0 10 inch H20 Medium 0 2A 1 59 m min 1 53 mm H20 28 dBA 2 4 W 1600 RPM 56 CFM 0 06 inch H20 Low 0 13A 1 1 m min 0 92 mm H20 25 dBA 1 6 W 1200 RPM 39 CFM 0 04 inch H20 Note These TriC
4. 5 drive bays and can house three hard disk drives For maximum flexibility you can mount the HDD cage anywhere within the external drive bays you are not limited to the bottom six bays Possible Drive Bay combinations include but are not limited to External 3 x 5 25 internal 6 x HDD default External 9 x 5 25 by removing both HDD cages External 6 x 5 25 internal 3 x HDD by removing one HDD cage External 3 x 5 25 internal 3 x HDD VGA cooling duct by adding the Middle Fan to one of the HDD cages see below External 5 25 Device Installation Note The HDD cages each occupy three consecutive drive bays and will block installation of larger devices such as optical drives so please plan ahead before installing your drives 1 Remove both side panels per the instructions in Setting Up 2 Remove the screws fastening the appropriate metal drive bay cover s to the sides of the case Remove the cover s 3 If necessary please remove the HDD cage that is preinstalled in the bay 4 Slide the 5 25 device into the bay from the front of the case 5 Fasten the drive using the screws that came with your drive 6 Mount the other devices accordingly 7 Connect the appropriate connector s from the power supply to the device s 3 5 Hard Drive Installation There are two HDD cages provided with the case Each can store three hard disk drives Pail 1 Remove both side panels per the instructi
5. HMEC The Bower of Mou Nine Hundred User s Manual Manuel de l utilisateur Anwenderhandbuch Manuale per l operatore Manual del usuario AVM ait AAS At Antec we continually refine and improve our products to ensure the highest quality So it s possible that your new case may differ slightly from the descriptions in this manual This isn t a problem it s simply an improvement As of the date of publication all features descriptions and illustrations in this manual are correct Disclaimer This manual is intended only as a guide for Antec s Computer Enclosures For more comprehensive instructions on installing the motherboard and peripherals please refer to the user s manuals which come with the components and drives Nine Hundred User s Manual The Nine Hundred comes without a power supply Make sure you choose a power supply that is compatible with and has long enough power harnesses to reach your motherboard and peripheral devices We recommend our TruePower 2 0 Neo HE or Phantom power supplies for the latest ATX specification compliance wide com patibility and power savings capability Most ATX power supplies come with an on off switch Make sure you turn the switch to the ON 1 position before you boot up your computer for the first time Normally you won t need to switch to the OFF O position since the power supply includes a soft on off feature This lets you turn your computer on and off by
6. ly useful in cooling dual VGA card implementations 1 In the toolbox you ll find a black plastic fan mount Place a 120mm fan in this fan mount 2 Run the power and control switch if using a TriCool fan through the cable guide that runs along the fan mount 3 Clip the fan mount fan assembly onto the back of the HDD cage that you do not have HDD s mounted in 4 Connect the fan to the power supply Antec Inc 47900 Fremont Blvd Fremont CA 94538 USA tel 510 770 1200 fax 510 770 1288 Antec Europe B V Sydneystraat 33 3047 BP Rotterdam The Netherlands tel 31 0 10 462 2060 fax 31 0 10 437 1752 Customer Support US amp Canada 1 800 22ANTEC customersupport antec com Europe 31 0 10 462 2060 europe techsupport antec com www antec com Copyright 2006 Antec Inc All rights reserved All trademarks are the property of their respective owners Reproduction in whole or in part without written permission is prohibited Printed in China Version 1 0 1 07 11 2006
7. ons in Setting Up 2 Remove the thumbscrews fastening the HDD cage to the 5 25 drive bays and set them x carefully aside Note do not confuse the HDD cage thumbscrews with the side panel thumb screws as they are different 3 Slide the HDD cage forward out of the front of i the case to remove it from the case 4 Mount the hard drive into the drive cage and fasten it using the screws provided in the tool bag 5 Repeat the same procedure for the other HDD s as necessary 6 Slide the HDD cage back to the case and fasten the thumbscrews 7 Connect the appropriate connector s from the power supply to the device s Note There is a middle fan bracket pre installed on one of the HDD cages Remove the middle fan bracket from the HDD cage if you decide to mount your hard drives into this cage External 3 5 Drive Installation In the toolbox you ll find a 3 5 to 5 25 drive bay adapter tray and an external 3 5 to 5 25 drive bay adapter cover 1 Remove both side panels per the instructions in Setting Up 2 Remove the drive bay cover from the drive bay you wish to install an external 3 5 drive into 3 Install your external 3 5 device into the tray 4 Slide the drive tray device assembly into the bay Screw the tray to the drive cage Cooling System The Top 200mm TriCool fan Antec understands you desire the coolest gaming system that s why the Nine Hundred comes with a 2
8. ool fans have a three speed switch that lets you choose between quiet performance or maximum cooling Note The minimum voltage to start a 120mm TriCool fan is 5V We recommend that you set the fan speed to High if you choose to connect the fan s to a fan control device or to the Fan Only connector found on some Antec power supplies A fan control device regulates the fan speed by varying the voltage which may start as low as 4 5 V to 5V Connecting a TriCool fan set on Medium or Low to a fan control device may result in the fan not being able to start because the already lowered voltage from the fan control device will be further reduced by the TriCool circuitry below 5V The Optional Fans There are two optional 120mm fan mounts the side fan on the left side panel and the middle fan at the rear end of the HDD cage We recommend using Antec 120mm TriCool fans and setting the speed to Low These two fans should be installed so that the air is blowing into the case 6 The Side Fan the Side fan is there to enhance VGA cooling Just drop a fan into the bracket on the side panel so that air is blowing into the case The Middle Fan the middle fan is designed to cool the CPU VGA card or the power supply if you choose to use a fanless power supply depending on which drive bays you install the HDD cage into You can use the middle fan on whichever drive cage you do NOT install hard drives in This design is especial
9. plies with fans on the bottom of the power supply will need to be mounted so that the fan is facing the top of the case Nine Hundred provides mounting holes for power supplies with standard mounting layouts to be installed upside up or upside down 2 Push the power supply to the back of the case and align the mounting holes 3 Attach the power supply to the case with the screws provided Installing the Motherboard This manual does not cover CPU RAM or expansion card installation Please consult your motherboard manual for specific mounting instructions and troubleshooting 1 Lay the case down with the open side facing up The drive cages and power supply mount should be visible 2 Make sure you have the correct I O panel for your motherboard If the panel provided with the case isn t suitable please contact your motherboard manufacturer for the correct I O panel 3 Line up your motherboard with the standoff holes and remember which holes are lined up Not all motherboards will match with all the provided holes this is normal and won t affect functionally In other words there will likely be extra holes Remove your motherboard by lifting it up Screw the brass standoffs into the threaded holes that line up with your motherboard Do not over tighten the standoffs Some standoffs may be pre installed for your convenience 6 Place your motherboard on the brass standoffs 7 Screw in your motherboard to the
10. using the soft switch on your computer case If your computer crashes and you can t shut it down using the soft switch you can switch the main power to the OFF O position to clear the fault then reboot Attention Nine Hundred comes with a top storage tray Antec does not recommend that users put any liquid containing items drinks candles coffee perfume etc in this area Feel free to put your personal media player digital camera keys coins etc in the top storage tray Setting Up 1 Place the case upright on a flat stable surface so that the rear panel power supply and expansion slots is facing you 2 Remove the thumbscrews from a side panel and open it by sliding it towards yourself Place the thumbscrews carefully aside as they are NOT interchangeable with the HDD cage thumbscrews Note Don t use your fingernail to pry or lift the panels 3 Remove the thumbscrews from the other side panel and open it by sliding it towards yourself Place the screws carefully aside Inside the case is the power supply mount at the lower rear of the case and the 5 25 drive bay area with two HDD cages inside the bays You will also find some wiring with marked connectors USB PWR etc an installed I O panel and a toolbox containing more hardware screws brass standoffs etc Installing the Power Supply 1 With the case upright place the power supply on a h the four silicone pads on the bottom of the case Note Power sup
Download Pdf Manuals
Related Search