JBL SB100
Contents
1. remote s Bass Boost button to enhance low frequency performance resulting in bass with more impact which you may prefer while watching movies or listening to music There is no harm in experimenting with this control Pressing the Bass Boost button again will return the soundbar s normal low frequency performance Bass Boost Button UBL LEARNING YOUR TV REMOTE S VOLUME AND MUTE COMMANDS You can program the soundbar so it will respond to your TV remote s volume up volume down and mute commands This will let you control both the soundbar and your TV with a single remote Before you begin to program the soundbar have your TV remote in hand 1 Press and hold the soundbar s Surround button until the button begins flashing amber Press and Hold Until Button Flashes Amber S06 2 Hold your TV s remote approximately 12 80cm from the front of the soundbar and aim the remote directly at the soundbar FSF Remote e Press the TV remote s volume up button while pressing and holding the soundbar s Volume button If the programming was successful the soundbar s Surround button will change from amber to solid white for one second then will return to flashing amber A Hold Down Soundbar s Volume Button 5666 s B Press TV Remote s Volume Up Button e Press the TV remote s volume down button while pressing and holding the soundbar s Volume button If t2. the soundbar s EQ switch in the Table position See Soundbar Rear Panel Controls and Connections on page 2 WALL MOUNTING THE SOUNDBAR If your TV is attached to a wall you can use the included wall mount bracket to mount the soundbar on the wall directly below the TV screen 1 Determine the location for the soundbar on the wall Make sure that the top of the soundbar will not block your view of the TV screen when it is mounted on the wall 2 Hold the bracket against the wall as a template and mark the locations of the soundbar wall mount bracket holes on the wall The two holes should be spaced 4 9 16 115mm apart and the bracket slots are designed to accept 4mm screws Make sure that the holes are at the same height See the illustration below Mark Bracket Hole Locations 4 9 16 115mm Apart 8 Attach the wall mount bracket to the wall at the locations you marked using hardware that is appropriate for the wall s construction and materials Note that the soundbar weighs 2 5kg 5 5 Ib Be sure to use hardware that can support this weight Before you tighten the mounting screws all the way use a carpenter s level laser sight or other device to check if the bracket is level The bracket s slots allow you to adjust the bracket s angle on the wall to ensure that it is level Once the bracket is level tighten the mounting screws 4 After reading the Connections section on page 4 bri
3. JBL by HARMAN CINEMA B100 powered soundbar speaker QUICK START GUIDE THANK YOU FOR CHOOSING THIS JBL We re confident that this JBL system will provide every note PRODUCT of enjoyment that you expect and that when you think about purchasing additional audio equipment for your home car or The JBL Cinema SB100 powered soundbar speaker is a complete office you will once again choose JBL products integrated sound system that will dramatically improve the sound of programs you watch on your television It can mount on a wall This quick start guide contains all the information you need to set or sit on a shelf and includes all of the cables you need to connect up connect and adjust your new speaker system For more in it to your TV and your cable satellite tuner or disc player depth information go to our Web site www jbl com INCLUDED ITEMS SOUNDBAR REAR PANEL CONTROLS AND CONNECTIONS Subwoofer Output Connector EQ Switch Optical Input Connector Aux Input Connector le CINEMA SB100 cen Po 1eO0E Power Switch Power Cord Connector Subwoofer Output connector If you are using a powered subwoofer not supplied with your soundbar connect it here Note This connector outputs a low pass filtered signal so connect it to an input on your subwoofer that bypasses the subwoofer
4. NDBAR SYSTEM TURNING THE SOUNDBAR ON AND OFF Set the soundbar s Power switcn to the On position Power Switch Press the Power button on either the soundbar or the remote to turn the soundbar on To put the soundbar in the Standby mode press either Power button while the soundbar is on Power Button Power Button S666 If you do not press the Power button the soundbar will automatically go into the Standby mode approximately 10 minutes after the audio signal ceases NOTE If you have put the soundbar into the Standby mode by pressing the Power button you must manually turn it on by pressing the Power button again If the soundbar has automatically gone into the Standby mode 10 minutes after the audio signal has ceased it will automatically turn itself on when it receives an audio signal at either input connection If you will be away from home for an extended period of time or if you will not be using the soundbar for an extended period set the soundbar s Power switch to the Off position SWITCHING SOURCES Press the soundbar s or remote s Source button to switch between the devices you connected to the Aux input and Optical input When the Aux input is active the soundbar s Source indicator will illuminate white when the Optical input is active the soundbar s Source indicator will illuminate amber Source Button S066 Source Button ADJUSTING THE SYSTEM S VOL
5. UME Press the soundbar s or remote s Volume and buttons to raise and lower the system s volume one step at a time Hold down the buttons to continuously raise or lower the volume Volume Buttons Volume Buttons CIU For the best sound we recommend turning your TV s built in speakers off Consult your TV s owner s manual to find out how to do this MUTING THE SYSTEM Momentarily press both of the soundbar s Volume buttons at the same time or press the remote s Mute button to mute the system Both Volume indicators illuminate Momentarily press either of the soundbar s Volume buttons or press the remote s Mute button again to un mute the system The Volume indicators turn off Both Volume Mute Buttons Button Cc UBL CHANGING THE SURROUND MODE Press the soundbar s or remote s Surround Mode indicator to switch the sound between normal stereo the Surround Mode indicator lights white and HARMAN Display Surround the Surround Mode indicator lights amber The HARMAN Display Surround setting will produce a complete surround sound experience for anyone sitting in front of and several feet away from the soundbar Although it is particularly effective when watching movies you can also try the HARMAN Display Surround setting for music Surround Mode Button C2 Oo Surround Mode Button BOOSTING THE BASS Press the
6. dustries Incorporated AGAMN 8500 Balboa Boulevard Northridge CA 91329 USA 2012 HARMAN International Industries Incorporated All rights reserved JBL is a trademark of HARMAN International Industries Incorporated registered in the United States and or other countries All Rights Reserved Features specifications and appearance are subject to change without notice www jbl com Part No 950 0470 001 Rev A
7. he programming was successful the soundbar s Surround button will change from amber to solid white for one second then will return to flashing amber A Hold Down Soundbar s Volume Button O66 r B Press TV Remote s Volume Down Button e Press the TV remote s mute button while pressing and holding the soundbar s Volume and Volume buttons at the same time If the programming was successful the soundbar s Surround button will change from amber to solid white for one second then will return to flashing amber A Hold Down Soundbar s Volume and Button A Cc B Press TV Remote s Mite Button 3 When you re finished press and hold the soundbar s Surround button until the button stops flashing amber The soundbar will now respond to your TV remote s volume and mute commands SPECIFICATIONS CINEMA SB100 POWERED SOUNDBAR SPEAKER Low frequency transducer One 3 77mm cone per channel High frequency transducer One 1 1 2 88mm tweeter per channel 30 watts peak per channel 80Hz 18kHz 6dB 100V 240V 50Hz 60Hz 30W Amplifier power Frequency response Power requirement lt 0 5W standby 30W maximum 4 1 4 x 31 7 8 x 3 5 8 108mm x 810mm x 92mm 8 4 Ib 3 8kg Power consumption Dimensions H x W x D Weight shipping eS JBL by HARMAN HARMAN HARMAN International In
8. ng all the cables through the opening in the bracket as shown in the illustration below and connect them to the soundbar IMPORTANT Do NOT plug the soundbar s power cord into an AC outlet at this time Ce gO EJ Bring all ra Cables Through Bracket Opening U e Set the soundbar s EQ switch in the Wall position and set the soundbar s Power switch in the On position See Soundbar Rear Panel Controls and Connections on page 2 5 Attach the soundbar to the bracket by sliding the bracket s upper tabs into the slots at the top of the soundbar s connector section The bracket s lower tabs should snap into the slots on the botton of the soundbar If necessary rotate the front of the soundbar down slightly to get the tabs into the slots Insert Tabs on Bracket into Slots on Soundbar NOTE If your disc player cable tuner or satellite tuner does not have an optical digital output you can connect its analog audio output to your TV The TV will send its audio signal to the soundbar through the analog CONNECTIONS SOURCE CONNECTIONS Analog Use the supplied stereo audio cable to connect the soundbar s connection described above Aux analog input to your TV s stereo audio output If your TV has two sets of audio output jacks use the set that has a fixed not variable Subwoofer If you are using an optional powered subwoofer with y
9. or an extended period for instance if you re going on vacation set the Power switch to the Off position SOUNDBAR TOP PANEL CONTROLS AND REMOTE CONTROL an Volume Power Source Surround Buttons Button Button Button Power Button W Mute Button Volume Buttons Surround Mode E gt Bass Boost Button Button Source Button O UBL Power button To turn the soundbar on when it is in the Standby mode press the Power button on either the soundbar or the remote The Power indicator will turn white To put the soundbar in the Standby mode press either Power button while the system is on The Power indicator will turn amber If you do not press the Power button the soundbar will automatically go into the Standby mode approximately 10 minutes after the audio signal ceases NOTE If you put the soundbar into the Standby mode by pressing the Power button you must manually turn it on by pressing the Power button again If the soundbar automatically goes into the Standby mode 10 minutes after the audio signal ceases it will automatically turn on whenever the soundbar detects an audio signal at either input connection Mute button remote control only Press the Mute button to mute the soundbar The Volume indicators both illuminate white While the system is muted press the Mute button again or either Volume button to restore the sound NOTE Pressing both of
10. our soundbar use a mono audio cable not supplied to connect it to the soundbar s Subwoofer connector Consult your subwoofer s owner s manual for instructions about connections and adjustments output level This will let you turn your TV s speakers all the way off while the TV still supplies a constant audio signal to the soundbar Digital If your disc player cable tuner or satellite tuner has an optical digital output you can use the supplied optical digital audio cable to connect it to the soundbar s Optical digital input CINEMA SB100 i SHARMAN A a Oka ee S Optical Audio Cable Mono Audio Cable f Cable not supplied Supplied supplied N I Powered Subwoofer optional i l I eet I I 1 l I Disc Player or f Cable Satellite Tuner l I l OPTICAL DIGITAL gee HA OUT oad ee ee Remove Caps g T POWER CONNECTIONS After verifying that all of the source connections have been made properly plug the supplied power cord into the soundbar s Power Cord connector and plug the other end into an active unswitched AC outlet Do NOT plug this cord into the accessory outlet found on some audio components Power Cord supplied To Unswitched 4 AC Outlet USING YOUR SOU
11. s built in crossover network Consult your subwoofer s owner s manual for instructions about connections and adjustments EQ switch Use this switch to adjust the soundbar s bass for either wall or table mounting If you re mounting the soundbar on a wall with the included wall mount bracket set the EQ switch to the Wall position for the most natural sounding bass performance If you are placing the soundbar on a table set the EQ switch to the Table position for the most natural sounding bass performance Optical Input connector digital If your TV disc player or cable satellite tuner has an optical digital output use the included optical cable to connect it here NOTE You can connect different source components to the analog and digital connections Aux Input connection analog Use the included stereo 3 5mm to stereo RCA audio cable to connect the stereo analog outputs of your TV disc player or cable satellite tuner here Power switch Set this switch to the On position to activate the soundbar In normal operation this switch will be left in the On position See Turning the Soundbar On and Off on page 5 for more information Power Cord connector Connect the included power cord here See Power Connections on page 5 for more information IMPORTANT Do not connect the power cord to an AC outlet until you have made and verified all other connections If you will not be using the soundbar f
12. the soundbar s Volume buttons at the same time while the system is on will mute the system Pressing either Volume button while the system is muted will restore the sound Surround Mode button This button turns the soundbar s HARMAN Display Surround processing on and off The Surround button indicator turns amber when HARMAN Display Surround is active and turns white when HARMAN Display Surround is not active normal stereo sound See Surround Mode Buttons on page 6 for more information Volume Up Down buttons Press the button to increase the volume press the button to decrease the volume The buttons illuminate white for a few seconds after being pressed Source Selector button This button switches between the sources connected to the Aux analog and Optical digital inputs When the Aux input is active the Source indicator turns white when the Optical input is active the Source indicator turns amber Bass Boost button remote control only Press the remote s Bass Boost button to enhance low frequency performance Pressing the Bass Boost button again will return the soundbar s normal low frequency performance O SOUNDBAR PLACEMENT PLACING THE SOUNDBAR ON A TABLE If your TV is placed on a table you can place the soundbar on the table directly in front of the TV stand centered with the TV screen As long as the surface of the table is flat the soundbar will rest on its rubber bumpers e Set
Download Pdf Manuals
Related Search