Home

NEC P402-TMX4P

1. 6 Switch on the power of all the attached external equipment When connected with a computer switch on the power of the computer first 7 Operate the attached external equipment Display the signal from the desired input source 8 Adjust the sound Make volume adjustments when required 9 Adjust the screen See pages 20 and 21 Make adjustments of the screen display position when necessary 10 Adjust the image See page 20 Make adjustments such as backlight or contrast when required 11 Recommended Adjustments To reduce the risk of the Image Persistence please adjust the following items based on the application being used SCREEN SAVER SIDE BORDER COLOR See page 24 DATE amp TIME SCHEDULE SETTINGS See page 21 It is recommended that the FAN CONTROL setting See page 24 be turned to ON also English 13 Connections NOTE Do not connect disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image NOTE Use an audio cable without a built in resistor Using an audio cable with a built in resistor turns down the sound Before making connections firstturn off the power of all the attached equipment and make connections Refer to the user manual included with each separate piece of equipment Wiring Diagra
2. RS 232C IN RS 232C OUT RS 232C IN RS 232C OUT Out RS 232C Cable a RS 232C Cable n oS y DUUM Junt MONTI ammi LT MultiSync NOTE If your PC is equipped only with a 25 pin serial port connector a 25 pin serial port adapter is required Contact your dealer for details Check the ID ALL REPLY setting in EXTERNAL CONTROL n order to function the RS 232C OUT terminal can only be connected to another monitor of the same model Do not connect to other types of equipment To control monitor or multiple monitors that are daisy chained together please use the control command Instructions for the control command can be found on the CD included with the display The file is called External control pdf Multiple monitors that are daisy chained have a limit to the conectable monitor 1 Interface PROTOCOL RS 232C BAUD RATE 9600 bps DATA LENGTH 8 bits PARITY BIT NONE STOP BIT 1 bit FLOW CONTROL NONE This LCD monitor uses RXD TXD and GND lines for RS 232C control The reverse type cable null modem cable not include should be used for RS 232C control 2 Control command diagram Please see file External Control pdf on the CD ROM English 30 Controlling the LCD monitor via LAN Control Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Sett
3. DVI D 24pin Digital RGB DisplayPort DisplayPort Connector Digital RGB 15pin Mini D sub Analog RGB Sync RGB HV BNC R G B H V Analog RGB Sync HDMI HDMI Connector Digital YUV Digital RGB Component DVD HD BNC X3 VIDEO1 BNC Composite VIDEO2 BNC S VIDEO Mini DIN 4 pin S VIDEO Ms Signal DVI D 24pin Digital RGB DisplayPort E Connector Digital RGB AUDIO AUDIO RCA L R Analog Audio Input STEREO Mini Jack X2 HDMI Connector Digital Audio AUDIO STEREO Mini Jack Analog Audio Output Speaker Output Control RS 232C In RS 232C Out LAN Remote IN Remote OUT Power Supply Operational Environment Temperature Humidity Altitude Storage Environment Temperature Humidity Dimension Weight VESA compatible mounting interface Power Management Plug amp Play Accessories NOTE Technical specifications are subject to change without notice 40 1016 mm diagonal 0 461 mm 1920 x 1080 Over 16 million colors depending on video card used 650 cd m Max 500 cd m Factory setting Typ 25 C 3000 1 89 typ 9 CR gt 10 15 625 15 734 kHz 31 5 kHz 91 1 kHz Analog Input 31 5 kHz 91 1 kHz Digital Input 50 0 85 0 Hz 25 2 MHz 162 0 MHz 885 6 x 498 2 mm DVI HDCP VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz 1080p 1080i DisplayPort Complies with Standard V1 1a applicable to HDCP V1 3 VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920x1080 60 Hz 1080p
4. MENU OSD will appear on the selected target monitor NOTE Ifthe ID No mode select OSD is showing press the DISPLAY button on the remote control while pointing at the PRIMARY monitor to clear this OSD HINT If you lost control due to the incorrect setting of IR CONTROL pressing the DISPLAY button on the remote control for 5 or more seconds will reset the IR CONTROL menu to NORMAL function WIRED REMOTE CONTROL FUNCTION You can control this monitor by connecting REMOTE IN OUT with Stereo Mini plug cable 3 5 XP ee MultiSync MultiSync a LL Remote IN Remote OUT Remote IN Remote OUT aum 4 cu m 4 E Multi Sync Remote control cable Remote control c able NOTE Turn off the main power switch before connect disconnect Stereo Mini plug cable NOTE Do not use this connector unless specified English 29 Controlling the LCD monitor via RS 232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS 232C terminal NOTE When you use this function EXTERNAL CONTROL should be RS 232C See page 23 Functions that can be controlled by a personal computer are e Power ON or OFF e Switching between input signals Connection LCD Monitor PC i MultiSync MultiSync
5. An interval between 3 to 10 seconds for the Information OSD to appear is available ON 3 Sec MONITOR INFORMATION Indicates the model and serial number of your monitor CARBON SAVINGS Display the estimated carbon saving information in kg The carbon footprint factor in the carbon saving calculation is based on the OECD 2008 Edition OSD TRANSPARENCY Set the transparency of the OSD OSD ROTATION Determines the OSD display direction between landscape and portrait LANDSCAPE Display the OSD with landscape mode PORTRAIT Display the OSD with portrait mode INPUT NAME You can create a name for the INPUT currently being used Max 8 characters including Space A Z 0 9 and some symbols CLOSED CAPTION Activates closed captioning OFF VIDEO1 VIDEO2 S VIDEO inputs only RESET Resets the following settings within the OSD menu back to factory setting MENU DISPLAY TIME OSD POSITION INFORMATION OSD OSD TRANSPARENCY CLOSED CAPTION MULTI DISPLAY CONTROL ID Sets the monitor ID number from 1 100 and group ID from A J When YES is selected in AUTO ID monitor ID numbers are set automatically in all monitors which follow in the chain NOTE Group ID is made of multiple selections IR CONTROL Selects the mode of the monitor for use with the infra red remote control when using the RS 232C daisy chain NORMAL The monitor will be controlled normally using the remote controller PRIMARY Choose PRIMARY for the first monito
6. V position Clock Phase and White Level VGA RGB HV inputs only AUTO ADJUST H Position V Position and Phase are adjusted automatically when new timing is detected VGA RGB HV inputs only H POSITION Controls the horizontal position of the image within the Display area of the LCD uua dM CU Press to move right Press to move left V POSITION Controls the vertical position of the image within the Display area of the LCD AR T QE Press to move up Press to move down CLOCK Press to expand the width of the image on the right of the screen du PA Press to narrow the width of the image on the left PHASE Adjusts the visual noise on the image VGA RGB HV DVD HD SCART inputs only depends on signal input English 20 H RESOLUTION Adjusts the horizontal size of the image VGA RGB HV inputs only V RESOLUTION Adjusts the vertical size of the image VGA RGB HV inputs only INPUT RESOLUTION VGA RGB HV inputs only AUTO If there is a problem with signal detection this function forces the monitor to display the signal at the desired resolution After selection execute AUTO SETUP if required If no problem is detected the only available option will be AUTO ASPECT Select the aspect ratio of the screen image FULL NORMAL Displays the aspect ratio the same as it is sent from the source LR FULL Fills entire screen Loe li WIDE Expands a 16 9 letter box signal to fill entire screen aT DYNAMI
7. 720p 0 7 Vp p 75 ohm VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz Separate TTL level Pos Neg Composite sync on Green Video 0 3 Vp p Neg 0 7 Vp p 75 ohm VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz Separate TTL level Pos Neg Composite sync on Green Video 0 3 Vp p Neg HDMI VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920x1080 60 Hz 1080p 1080i 720p 50Hz 60Hz 576p 9 50Hz 480p 60Hz 576i 50Hz 480i 60Hz Y 1 0 Vp p 75ohm Cb Cr Pb Pr 0 7 Vp p 75 ohm HDTV DVD 1080p 1080i 720p Q9 50Hz 60Hz 576p 9 50Hz 480p 60Hz 576i 50Hz 480i 9 60Hz 1 0 Vp p 75 ohm NTSC PAL SECAM 4 43NTSC PAL60 Y 1 0 Vp p 75 ohm C 0 286 Vp p 75 ohm NTSC 0 3 Vp p 75 ohm PAL SECAM NTSC PAL SECAM 4 43NTSC PAL60 DVI HDCP DisplayPort Complies with Standard V1 1a applicable to HDCP V1 3 1 0 Vp p with 75 ohm terminated Stereo L R 0 5 Vrms PCM 32 44 1 48 KHz 16 20 24bit Stereo L R 0 5 Vrms External Speaker Jack 15 W 15 W 8 ohm Internal Speaker 10W 10W 9 Pin D sub 9 Pin D sub with daisy chain RJ 45 10 100 BASE T Stereo Mini jack 3 5 P Stereo Mini jack 3 5 P 3 5 1 45 A 100 240V AC 50 60Hz 5 40 C 41 104 F Default brightness 5 20 C 41 68 F Max brightness 20 8096 without condensation 0 3000 m Brightness may decrease with altitude 20 60 C 4 140 F 10 90 without condensation 90 3 5 x Temp 40 C reg
8. Power ON and ORF MOGGS i inte oie Sn te demo den English 16 FPOWG Indicato ter a i E a ierecagtune waaeet English 17 Using Power Management xc2eccasisansetnctsazaace taxcacaiancwiaetncascnsastanee sets oder one een tenons does English 17 Selecting a video SOULCE ccccceeceecceeseeeccessececeuaueecceaueeeceeaseeecseeeeeseaseeeesaueeecseaeeeessaeeessnaeeesssagss English 17 PCE ASHO Cia emannccadtheacedseensnteoteesn atendesantcasbecadaednceseecaateaastuaaa ccacantaceesecnsntcbteece English 17 Miormaton OS Dassie aa e e AOE English 18 Pietre IM OGG crna Re a a a A aire English 18 OSD On Screen Display CONVO ariaa a A eee English 19 PICTURES a c M I ean gee English 20 ADI PR E MM LI DU CIA uM E English 20 FAN US BD e o TNR English 21 SCHEDULE sance a ISR Toe oe OR RCE ds bL Me Cs English 21 D RSR RE RP SA S EA ee teme Sao ossa Se cU English 22 GS DR HC ct p English 22 MUETMDIS PLAY Ee English 23 BiSE VEIIIenzeije e EE English 24 ADVANCED OPTIONS English 25 Remote CORTOEUACHIOM ESS T hs cs fence end we o oT 20 D Ai eset English 28 Controlling the LCD monitor via RS 232C Remote Control ss English 30 Controlling the LCD monitor via LAN Control sise English 31 Connecting to a Network iR PEE English 31 Network Setting by Using an HTTP Browser English 31 POS eT ehe e English 35 TrOUDI SNOGUNA emm TTC English 36 Specifications u 10 cE lues English 37 SDECIICA
9. be downloaded from our website NOTE Ifthe MONITOR NETWORK SETTINGS screen does not appear in the web browser press the Ctrl F5 keys to refresh your web browser or clear the cache The display or button s response can be slowed down or operation may not be accepted depending the settings of your network Should this happen consult your network administrator The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals Should this happen wait a moment and repeat If you still can t get a response turn the monitor off and then back on English 31 Preparation Before Use Connect the monitor to a commercially available LAN cable before engaging in browser operations Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method Although the type of proxy server will be a factor it is possible that items that have actually been set will not be displayed depending on the effectiveness of the cache and the contents set from the browser may not be reflected in operation It is recommended that a proxy server not be used unless it is unavailable Handling of the Address for Operation via a Browser The host name can be used under the following cases If the host name corresponding to the IP address of the monitor has been registered to the domain name server DNS by the network administrator you can then access the network settings of the di
10. can be connected using RS 232C 2 Set Monitor ID and IR Control mode For proper operation the Monitor ID should be set in the OSD menu of each monitor that is in the chain The Monitor ID can be set under the MULTI DISPLAY menu in the OSD The Monitor ID number can be set within a range from 1 to 100 No two monitors should share the same Monitor ID number It is recommended to number each monitor in a daisy chain sequentially from 1 The first monitor in the daisy chain is designated as the primary monitor Subsequent monitors with the chain are secondary monitors In the ADVANCED OPTION menu on the first monitor in the RS 232C daisy chain set the IR CONTROL to PRIMARY Set the IR CONTROL to SECONDARY on all other monitors English 28 3 Press the DISPLAY button on the remote control while aiming at the PRIMARY monitor The Information OSD will be shown at top left side of the screen Monitor ID Displays the ID number of the current monitor within the daisy chain Target ID Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor Press the or buttons to change the Target ID to show the ID number of the monitor to be controlled To control the entire daisy chained monitors simultaneously select ALL as the Target ID 4 Use the wireless remote controller to control the SECONDARY monitor while aiming at the PRIMARY monitor The
11. cases in which certain content is protected with HDCP and might not be displayed due to the decision intention of the HDCP community Digital Content Protection LLC Option board slot You can use an option board Please contact your supplier for detailed information When you use slot 2 type option board you need to install it with the optional SB 02AM adapter English 35 Troubleshooting No picture e The signal cable should be completely connected to the display card computer e The display card should be completely seated in its slot e Check the main Power Switch it should be in the ON position e Front Power Switch and computer power switch should be in the ON position e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode e Check the monitor and your display card with respect to compatibility and recommended settings e Check the signal cable connector for bent or pushed in pins Power Button does not respond e Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor e Check the main Power Switch on the back side of the monitor Image persistence e Please be aware that LCD Technology may experience a phenomenon known as Image Persistence Image Persistence occurs when a residual or ghost image of a previous image remains visible on the screen Unlike
12. for signs of damage or weakness that may occur over time English 5 Attaching Mounting Accessories The monitor is designed for use with the VESA mounting system 1 Attach Mounting Accessories Be careful to avoid tipping monitor when attaching accessories VESA Mounting Interface PAS ZINS 300 mm P402 P462 400 mm P552 lt a 300 mm P402 P462 400 mm P552 Mounting accessories can be attached with the monitor in the face down position To avoid damaging the screen face place the protective sheet on the table underneath the LCD The protective sheet was wrapped around the LCD in the original packaging Make sure there is nothing on the table that can damage the monitor When using mounting accessories other than NEC compliant and approved they must comply with the VESA compatible mounting method 2 Installing and removing optional table top stand CAUTION Installing and removing the stand must be done by two or more people P402 P462 by four or more people P552 To install follow those instructions included with the stand or mounting apparatus Use only those devices recommended by the manufacturer NOTE Use ONLY thumbscrews which are included in the monitor When installing the LCD monitor stand handle the unit with care to avoid pinching your fingers Optional table top stand Protective Sheet Install the stand so the long end of the feet face forward
13. is available for slot 2 The function is available for slot 2 type PC PC OFF WARNING If OPTION POWER is OFF a warning message appears when monitor power is turned off NOTE Warning message does not appear when monitor power is turned off by OFF TIMER setting or SCHEDULE setting AUTO OFF Monitor power is automatically OFF when connected PC is OFF or the monitor is in power save P3 ISTARTUPPC UP PC When ON is selected connected PC start up FORCE FORCEQUIT When ON is selected it performs force quit PC 120H2 ri EDS Ss o OU UG O MURA COMP oaos Resets the following settings within the ADVANCED OPTION menu back to factory setting INPUT DETECT except the priority of input signals INPUT CHANGE TERMINAL SETTING DEINTERLACE COLOR SYSTEM OVER SCAN START UP PC in OPTION SETTING and FORCE QUIT in OPTION SETTING FACTORY RESET Resets OSD options back to factory settings EXCEPT FOR PICTURE MODE VOLUME SCHEDULE SETTINGS DATE amp TIME ASPECT in PIP SUB INPUT in PIP LANGUAGE OSD ROTATION CHANGE SECURITY PASSWORD and SECURITY English 26 NOTE 1 CREATING A SCHEDULE The schedule function allows the display to be set to power on and off at different times Up to seven different schedules can be programmed To program the schedule Enter the SCHEDULE menu Highlight SCHEDULE SETTINGS using the up and down buttons Press the SET or the button to enter the Settings menu Highlight the desired sch
14. menu Toggle switches between DVI DPORT VGA RGB HV HDMI DVD HD SCART VIDEO1 VIDEO2 or S VIDEO These are available input only shown as their factory preset name PLUS button Acts as button to increase the adjustment with OSD menu Increases the audio output level when the OSD menu is turned off MINUS button Acts as button to decrease the adjustment with OSD menu Decreases the audio output level when the OSD menu is turned off UP button Activates the OSD menu when the OSD menu is turned off Acts as A button to move the highlighted area up to select adjustment items within OSD menu DOWN button Activates the OSD menu when the OSD menu is turned off Acts as WV button to move the highlighted area down to select adjustment items within OSD menu tt a 0 INPUT MUTE 4 EXIT button Activates the OSD menu when the OSD menu is turned off Acts as EXIT button within the OSD to move to previous menu Remote control sensor and Power Indicator Receives the signal from the remote control when using the wireless remote control See also page 10 Glows green when the LCD monitor is in active mode Glows red when the LCD is in POWER OFF mode Glows amber when the monitor is in Power Save Mode Green and Amber blink alternately while in Power Standby mode with the SCHEDULE SETTINGS function enabled Wh
15. of the display when the keyboard or the mouse has not been used for a fixed period The power management feature on your new display has been set to the ON mode This allows your display to enter a Power Saving Mode when no signal is applied This could potentially increase the life and decrease the power consumption of the display NOTE Depending on the PC and video card used this function may not operate NOTE lt takes about 10 minutes for the monitor to go into power management mode when using DVD HD SCART VIDEO1 VIDEO2 and S VIDEO Selecting a video source To view a video source Use the input button to set VIDEO1 VIDEO2 S VIDEO Use the COLOR SYSTEM menu to set AUTO NTSC PAL SECAM PAL 60 4 43NTSC according to your video format Picture Aspect DVI VGA RGB HV DPORT FULL 1 1 gt ZOOM NORMAL b HDMI DVD HD SCART VIDEO 1 VIDEO2 S VIDEO FULL WIDE DYNAMIC 1 1 ZOOM NORMAL Aspect rauo Unchanged view of image Recommended selection for picture aspect NORMAL D ES DYNAMIC Letterbox NORMAL Displays the aspect ratio the same as it is sent from the source 3 Grey areas indicate unused portions of the screen FULL Fills entire screen WIDE Expands a 16 9 letter box signal to fill entire screen DYNAMIC Expands a 4 3 pictures to fill the entire screen with non linearity Some of the outs
16. the overall image and background brightness Press or to adjust Note When AMBIENT 1 or AMBIENT is selected in picture mode this function cannot be changed CONTRAST Adjusts the image brightness in relationship to the input signal Press or to adjust Note When sRGB is selected in picture mode this function cannot be changed BRIGHTNESS Adjusts the image brightness in relationship to the background Press or to adjust Note When sRGB is selected in picture mode this function cannot be changed ale S m Adjusts the hue of the screen Press or to adjust Note When sRGB is selected in picture mode this function cannot be changed COLOR Adjusts the color depth of the screen Press or to adjust Note When sRGB is selected in picture mode this function cannot be changed COLOR TEMPERATURE When PROGRAMMABLE is selected in GAMMA CORRECTION this function cannot be changed COLOR CONTROL Adjusts the hue of the Red Yellow Green Cyan Blue and Magenta Note When sRGB is selected in picture mode this function cannot be changed Adjusts the color temperature of the entire screen A low color temperature will make the screen 10000K reddish A high color temperature will make the screen bluish If TEMPERATURE needs further adjustment the individual R G B levels of the white point can be adjusted To adjust the R G B levels CUSTOM must be showing as the COLOR TEMP selection Note When sRGB is s
17. you to display your computer s screen image Some video cards with a pixel clock over 162MHz may not display an image correctly Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically Typical factory preset signal timing Scanning frequency Resolution Vertical 640 x 480 31 5 kHz 800 x 600 37 9 kHz 1024 x 768 48 4 kHz 1860x768 48kHz 60Hz 1280x1024 64kHz 60Hz e lf you use with a Macintosh PowerBook set Mirroring to Off on your PowerBook Refer to your Macintosh s owner s manual for more information about your computer s video output requirements and any special identification or configuration your monitor s image and monitor may require e Input TMDS signals conforming to DVI standards e To maintain display quality use a cable that conforms to DVI standards Connecting a DVD Player or Computer with HDMI out e Please use an HDMI cable with HDMI logo e t may take a moment for the signal to appear e Some video cards or drivers may not display an image correctly Connecting a Computer with DisplayPort Please use DisplayPort cable with DisplayPort certified logo e t may take a moment for the signal to appear e Please note that DisplayPort connector does not supply power to the connected component e Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter an image may n
18. 1 0 Vp p 75 ohm C 0 286 Vp p 75 ohm NTSC 0 3 Vp p 75 ohm PAL SECAM NTSC PAL SECAM 4 43NTSC PAL60 DVI HDCP DisplayPort Complies with Standard V1 1a applicable to HDCP V1 3 1 0 Vp p with 75 ohm terminated Stereo L R 0 5 Vrms PCM 32 44 1 48 KHz 16 20 24bit Stereo L R 0 5 Vrms External Speaker Jack 15 W 15 W 8 ohm Internal Speaker 10W 10W 9 Pin D sub 9 Pin D sub with daisy chain RJ 45 10 100 BASE T Stereo Mini jack 3 5 P Stereo Mini jack 3 5 P 3 6 1 5 100 240V AC 50 60Hz 5 40 C 41 104 F Default brightness 5 20 C 41 68 F Max brightness 20 80 without condensation 0 3000 m Brightness may decrease with altitude 20 60 C 4 140 F 10 90 without condensation 90 3 5 x Temp 40 C regarding over 40 C 1055 4 W x 608 6 H x 118 0 D mm 41 6 W x 24 0 H x 4 6 D inches with handle 1055 4 W x 608 6 H x 103 0 D mm 41 6 W x 24 0 H x 4 1 D inches without handle 23 8 kg 52 5 lbs 300 mm x 300 mm M6 4 Holes VESA DPM VESA DDC2B DDC CI DisplayPort Setup manual Power Cord Video Signal cable Remote Control AA Battery x 2 Clamp x 3 Screw x 5 CD ROM Thumbscrew for optional stand x 2 Cable cover 1 Compressed image 2 Common terminal English 38 Specifications P552 Product Specifications LCD Module Pixel Pitch Resolution Color Brightness Contrast Ratio Viewing Angle Frequency Horizontal Vertica
19. C Expands a 4 3 pictures to fill the entire screen with non linearity Some of the outside image area will be cut off due to expansion Display the image in a 1 by 1 pixel format If the input resolution is higher than a 1920 x 1080 resolution the image will be scaled down to fit the screen ZOOM The image can be expanded beyond the active display area The image which is outside of active display area is not shown ZOOM Maintains the aspect ratio while zooming H ZOOM Amount of horizontal zoom V ZOOM Amount of vertical zoom H POS Horizontal position V POS Vertical position RESET Resets the following settings within the ADJUST menu back to factory setting AUTO ADJUST H POSITION V POSITION CLOCK PHASE H RESOLUTION V RESOLUTION ASPECT AUDIO VOLUME Increases or decreases output volume level BALANCE Adjust the balance of L R volume CENTER Press button to move the stereo sound image to right Press button to move the stereo sound image to left eo TREBLE To accentuate or reduce the high frequency sound Press button to increase TREBLE sound Press button to decrease TREBLE sound BASS To accentuate or reduce the low frequency sound Press button to increase BASS sound Press button to decrease BASS sound SURROUND O aL Artificial surround sound Note Audio out is disabled when this function is set to ON PIP AUDIO Selects source of PIP audio MAIN AUD
20. C in order to control RS 232C functions OUT connector Connect RS 232C output To connect multiple MultiSync monitors via RS 232C daisy Chain DISPLAYPORT connector IN connector To input DisplayPort signals OUT connector To output DisplayPort signals NOTE DisplayPort connectors are for image only No sound comes out Dvi DVI D IN connector To input digital RGB signals from a computer or HDTV device having a digital RGB output This connector does not support analog input OUT connector To output the DVI signal from either DVI IN or HDMI connection To output the DVI signal from the HDMI connection the HDMI input must be selected Q HDMI connector To input digital HDMI signals R Cr Pr G Y VIDEO IN IN IN1 IN3 VGA IN mini D Sub 15 pin To input analog RGB signals from a personal computer or from other RGB equipment RGB HV IN R G B H V BNC To input analog RGB signals or signals from other RGB equipment This is also to connect equipment such as a DVD player HDTV device and Set Top Box Sync on Green signal can be connected to the G connector This input can be used with an RGB DVD HD or Video source Please select signal type in TERMINAL SETTING D vipEo IN connector BNC To input a composite video signal Q0 VIDEO OUT connector BNC To output the composite video signal from the VIDEO IN connector B auoio ouT To out
21. CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use Image is unstable unfocused or swimming is apparent e Signal cable should be completely attached to the computer e Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment When the display mode is changed the OSD Image Adjust settings may need to be re adjusted e Check the monitor and your display card with respect to compatibility and recommended signal timings e f your text is garbled change the video mode to non interlace and use 60Hz refresh rate Image of component signal is greenish e Check to see if the DVD HD input connector is selected LED on monitor is not lit no green or red color can be seen e Power Switch should be in the ON position and power cord should be connected e Check the main Power Switch it should be in the ON position e Ma
22. DPORT VGA VGA RGB HV RGB HV HDMI HDMI DVD HD DVD HD SCART VIDEO VIDEO1 VIDEO2 S VIDEO S VIDEO OPTION Depends on your connection PICTURE MODE button Selects picture mode HIGHBRIGHT STANDARD sRGB CINEMA AMBIENT1 AMBIENT2 See page 18 HIGHBRIGHT for moving images such as DVD STANDARD for images SRGB for text based images CINEMA for movies AMBIENT1 and AMBIENT2 activate auto dimming function See page 18 ASPECT button Selects picture aspect FULL WIDE DYNAMIC 1 1 ZOOM and NORMAL See page 17 SOUND button Artificial surround sound for internal external speakers Audio out is disabled when surround is set to ON KEYPAD Press buttons to set and change passwords change channel and set REMOTE ID ENT button DISPLAY button Turns on off the information OSD See page 18 MENU button Turns on off the menu mode AUTO SETUP button Enters auto setup menu See page 20 EXIT button Returns to previous menu within OSD menu D UP DOWN button Acts as A button to move the highlighted area up or down to select adjustment items within OSD menu Small screen which adjusted PIP mode moves up or down B MINUS PLUS button Increases or decreases the adjustment level within OSD menu settings omall screen which adjusted PIP mode moves left or right D SET button Makes selection VOLUME UP DOWN button Increases or decreases
23. FF from second monitor MAC ADDRESS Displays the MAC ADDRESS English 23 LAN SETTING When you use this function EXTERNAL CONTROL should be LAN NOTE When changing the LAN SETTING you need to wait several seconds until the LAN SETTING is applied DHCP DISABLE Enabling this option automatically assigns an IP address to the monitor from your DHCP server Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator NOTE Consult your network administrator for the IP address when ENABLE is selected for DHCP IP ADDRESS Set your IP address of the network connected to the monitor when DISABLE is selected for 192 168 0 10 DHCP SUBNET MASK Set your subnet mask number of the network connected to the monitor when DISABLE is 255 255 255 0 selected for DHCP DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when DISABLE is selected 192 168 0 1 for DHCP DNS PRIMARY Set your primary DNS settings of the network connected to the monitor 0 0 0 0 DNS SECONDARY Set your secondary DNS settings of the network connected to the monitor 0 0 0 0 SETTING COPY In a daisy chain scenario select the OSD menu categories that you want to copy over to the other monitor NOTE When you use this function EXTERNAL CONTROL should be RS 232C This function resets to default when power is off This function has a li
24. GA60 SXGA60 UXGA60 1920x1080 60 Hz 1080p 720p 0 7 Vp p 75 ohm VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz Separate TTL level Pos Neg Composite sync on Green Video 0 3 Vp p Neg 0 7 Vp p 75 ohm VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz Separate TTL level Pos Neg Composite sync on Green Video 0 3 Vp p Neg HDMI VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920x1080 60 Hz 1080p 1080i 720p 50Hz 60Hz 576p 9 50Hz 480p 60Hz 576i 50Hz 480i 60Hz Y 1 0 Vp p 75ohm Cb Cr Pb Pr 0 7 Vp p 75 ohm HDTV DVD 1080p 1080i 720p Q9 50Hz 60Hz 576p 9 50Hz 480p 60Hz 576i 50Hz 480i 9 60Hz 1 0 Vp p 75 ohm NTSC PAL SECAM 4 43NTSC PAL60 Y 1 0 Vp p 75 ohm C 0 286 Vp p 75 ohm NTSC 0 3 Vp p 75 ohm PAL SECAM NTSC PAL SECAM 4 43NTSC PAL60 DVI HDCP DisplayPort Complies with Standard V1 1a applicable to HDCP V1 3 1 0 Vp p with 75 ohm terminated Stereo L R 0 5 Vrms PCM 32 44 1 48 KHz 16 20 24bit Stereo L R 0 5 Vrms External Speaker Jack 15 W 15 W 8 ohm Internal Speaker 10W 10W 9 Pin D sub 9 Pin D sub with daisy chain RJ 45 10 100 BASE T Stereo Mini jack 3 5 P Stereo Mini jack 3 5 P 5 0 2 0A 100 240V AC 50 60Hz 5 40 C 41 104 F Default brightness 5 20 C 41 68 F Max brightness 20 8096 without condensation 0 3000 m Brightness may decrease with altitude 20 60 C 4 140 F 10 90 without
25. IO LINE OUT Selecting VARIABLE enables control of the line out level with the VOLUME button FIXED Note LINE OUT is disabled when SURROUND is set to ON AUDIO INPUT Selects audio input source IN1 IN2 IN3 HDMI OPTION Depend on signal input RESET Resets AUDIO options back to factory settings except VOLUME SCHEDULE OFF TIMER Sets the monitor to power off after a length of time OFF A time between 1 to 24 hours is available SCHEDULE SETTINGS Creates a working schedule for the monitor to use SCHEDULE LIST List of schedules DATE amp TIME Sets the date time and daylight saving region Date amp time must be set in order for the SCHEDULE function to operate See page 27 YEAR Configures the year for the real time clock MONTH Configures the month for the real time clock DAY Configures the day for the real time clock The product you purchased may not have this feature English 21 TIME Configures the time for the real time clock DAYLIGHT SAVING Configures daylight savings on or off OFF HESET Resets the following settings within the SCHEDULE menu back to factory setting OFF TIMER SCHEDULE SETTINGS P KEEP PIP MODE Allows the monitor to remain in PIP and TEXT TICKER mode after powering off OFF When Power is returned PIP and TEXT TICKER appear without having to enter the OSD PIP MODE Selects Picture in Picture mode OFF O H Normal mode Picture in Picture mo
26. ND Expand image contrast and increase detail in the dark and bright areas DEINTERLACE Selects the IP Interlace to Progressive conversion function O Note For DVI input DVI HD needs to be enabled in the DVI mode menu Converts interlaced signals to progressive This is the default setting OFF Disables IP conversion This setting is best suited for motion pictures but increases the risk of O image retention COLOR SYSTEM The selected Color System depends on the video format of the input signal AUTO VIDEO1 VIDEO2 S VIDEO inputs only Automatically chooses Color System setting based on input signal PAL SECAM 4 43 NTSC PAL 60 English 25 OVER SCAN Some video formats may require different scanning modes in order to best display the image HDMI DVD HD SCART VIDEO1 VIDEO2 S VIDEO inputs only ON Image size is larger than what can be displayed The image edge will appear cropped Approximately 95 of the image will be shown on the screen LIEN Image size stays within the display area The whole image is displayed on the screen KE When you use a computer with HDMI out please set OFF UT SETTING You can set this setting when option board accessory is connected to the monitor EE contact your supplier for detailed information about Option board slot accessories OPTION POWER Allow the monitor to supply power to Option board slot during power save mode or standby NONE DI 3 INTERNAL PC The function
27. NG TO QUALIFIED SERVICE PERSONNEL J CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems CAUTION Please use the power cord provided with this monitor in accordance with the table below If a power cord is not supplied with this equipment please contact your supplier For all other cases please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country European Plug Type North America Continental uM AE D M E DE DEN E When operating the monitor with its AC 125 240V power supply use a power supply cord that matches the power supply voltage of the AC power outlet being used NOTE This product can only be serviced in the country where it was purchased Use the power cord wh
28. ONS PAG ed English 38 SD CIICAIONSS POS bissa a nee D m English 39 FIRS SIG IMIG IN e ee uaate English 40 Manufacturer s Recycling and Energy Information English 41 www necdisplaysolutions com DECLARATION OF CONFORMITY This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation U S Responsible Party NEC Display Solutions of America Inc Address 500 Park Boulevard Suite 1100 Itasca Illinois 60143 Tel No 630 467 3000 Type of Product Display Monitor Equipment Classification Class B Peripheral Model MultiSync P402 L400U5 MultiSync P462 L460U6 MultiSync P552 P552 C We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules Canadian Department of Communications Compliance Statement DOC This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60950 1 FCC Information 1 Use the attached specified cables with the MultiSync P402 L400U5 MultiSync P462 L460U6 MultiSync P552 P552 colour monitor
29. Use the ST 4020 for the P402 the ST 4620 for the P462 and the ST 5220 for the P552 3 Ventilation Requirements When mounting in an enclosed space or recessed area leave adequate room between the monitor and the enclosure to allow heat to disperse as shown below 100 mmt 100 mmt 100 mm1 100 mmt Allow adequate ventilation or provide air conditioning around the monitor so that heat can properly dissipate away from the unit and mounting apparatus especially when you use monitors in multiple screen NOTE The sound quality of the internal speakers will differ according to the acoustics of the room 4 Prevent Tipping When using the monitor with the optional table top stand fasten the LCD to a wall using a cord or chain that can support the weight of the monitor in order to prevent the monitor from falling Fasten the cord or chain to the monitor using the provided clamps and screws 204 mm P402 P462 400 mm P552 l Screw Holes Before attaching the LCD monitor to the wall make sure that the wall can support the weight of the monitor Be sure to remove the cord or chain from the wall before moving the LCD English 6 Parts Name and Functions Control Panel 1 i POWER button Switches the power on off See also page 16 MUTE button Switches the audio mute ON OFF INPUT button Acts as SET button within OSD
30. User s Manual NEC MultiSync P402 MultiSync P462 MultiSync P552 Index DECLARATION OF CONFORMITY presinga rosin nent rene dense Net English 1 important Re diio O English 2 Sete mH cr English 2 CAUTION Serseri idest adu dd blessed er tits hone obedece td edd English 2 Declaration Gasset English 2 Safety Precautions Maintenance amp Recommended Use ss English 3 Omen Co are trea Mn tease ELSE Ic uM EE English 4 IREI ELE a EE eau ci Mura teat a een ead dec de io tu English 5 Attaching Mounting Accessories Eds en citant tentent en cheats sens ete eres seas SM lee tn te English 6 Pans Name and FUNCUONS ss Ne rs pe dos aa pie onc nota E ineo nn festo ne English 7 OOM INS I ER RR D ce os et in English 7 T HANAl PANNE De ess etre eater English 8 Wireless Remote COMO Met PITE English 10 Operating Range for the Remote Control ss English 11 vp uetetvess English 12 CONE CONS mt tins English 14 Wining Diagrami seeni c LS English 14 Connecting a Personal Compute iioii alae ates a ns elec oe utens English 15 Connecting a DVD Player or Computer with HDMI out Re English 15 Connecting a Computer with DisplayPort sise English 15 BASIC OD AIOME ARS NE English 16
31. age via e mail when using wired LAN An error message notification will be sent when an error occurs in the monitor Alert Mail Checking ENABLE will turn on the Alert Mail feature Checking DISABLE will turn off the Alert Mail feature Host Name Type in the hostname of the network connected to the monitor Up to 60 alphanumeric characters can be used Domain Name Type in the domain name of the network connected to the monitor Up to 60 alphanumeric characters can be used Sender s Address Type in the senders address Up to 60 alphanumeric and symbols characters can be used SMTP Server Type in the SMTP server name to be connected to the monitor Up to 60 alphanumeric characters can be used Recipient s Address Type in your recipient s address Up to 60 alphanumeric and symbols characters can be used 1 to 3 Authentication Method This selects the authentication method of the e mail transmission POP3 Server This specifies the address of the POP3 server that is used in the authentication of the e mail User Name This sets the user name for logging into the authentication server when authentication is required for the e mail transmission Up to 60 alphanumeric characters can be used Password This sets the password for logging into the authentication server when authentication is required for the e mail transmission Up to 60 alphanumeric characters can be used TestMail Click this button to send a test mail to check if your settings are c
32. and electrical accessories such as signal cables or power cords When you need to dispose of your NEC display products please follow the guidance of your local authority or ask the shop where you purchased the product or if applicable follow any agreements made between yourself and NEC LL The mark on electrical and electronic products only applies to the current European Union Member States Outside the European Union If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method English 41
33. arding over 40 C 919 7 W x 532 2 H x 118 0 D mm 36 2 W x 21 0 H x 4 6 D inches with handle 919 7 W x 532 2 H x 103 0 D mm 36 2 W x 21 0 H x 4 1 D inches without handle 20 8 kg 45 9 lbs 300 mm x 300 mm M6 4 Holes VESA DPM VESA DDC2B DDC CI DisplayPort Setup manual Power Cord Video Signal cable Remote Control AA Battery x 2 Clamp x 3 Screw x 5 CD ROM Thumbscrew for optional stand x 2 Cable cover 1 Compressed image 2 Common terminal English 37 Specifications P462 Product Specifications LCD Module Pixel Pitch Resolution Color Brightness Contrast Ratio Viewing Angle Frequency Horizontal Vertical Pixel Clock Viewable Size Input Signal DVI DVI D 24pin Digital RGB DisplayPort Connector Digital RGB 15pin Mini D sub Analog RGB DisplayPort VGA Sync RGB HV BNC R G B H V Analog RGB Sync HDMI HDMI Connector Digital YUV Digital RGB BNC X3 Component BNC Composite BNC Mini DIN 4 pin S VIDEO Output Signal DVI DVI D 24pin Digital RGB DisplayPort DisplayPort Connector Digital RGB DVD HD VIDEO VIDEO2 S VIDEO VIDEO AUDIO AUDIO RCA L R Analog Audio Input STEREO Mini Jack X2 HDMI Connector Digital Audio AUDIO STEREO Mini Jack Analog Audio Output Speaker Output Control RS 232C In RS 232C Out LAN Remote IN Remote OUT Power Supply Operational Environment Temperature Humidity Altitude Storage Env
34. audio output level D CH UP DOWN button GUIDE button D MUTE button Turns on off mute function STILL button ON OFF button Activates deactivates still picture mode STILL CAPTURE button Captures still picture English 10 e PIP Picture In Picture button ON OFF button Toggle switches between PIP POP PICTURE BY PICTURE ASPECT and PICTURE BY PICTURE FULL See page 22 INPUT button Selects the picture in picture input signal CHANGE button Replaces to the main picture and sub picture Sub picture DPORT VGA RGB HV HDMI DVD HD SCART VIDEO1 VIDEO2 S VIDEO DVI No Yes Yes Yes No Yes Yes Yes Yes Yes DPORT Yes No Yes Yes Yes Yes Yes Yes Yes Yes VGA Yes Yes No No Yes Yes Yes Yes Yes Yes RGB HV Yes Yes No No Yes No No Yes No Yes HDMI No Yes Yes Yes No Yes Yes Yes Yes Yes DVD HD Yes Yes Yes No Yes No No Yes No Yes SCART Yes Yes Yes No Yes No No No No No VIDEO1 Yes Yes Yes Yes Yes Yes No No No No VIDEO2 Yes Yes Yes No Yes No No No No No S VIDEO Yes Yes Yes Yes Yes Yes No No No No REMOTE ID button Activates REMOTE ID function e MTS button DV Main picture AUDIO INPUT button Selects audio input source IN1 IN2 IN3 HDMI OPTION E button Activates closed captioning Note VIDEO VIDEO2 S VIDEO inputs only 1 The product you purchased may not have this feature 2 This butt
35. b signal Troubleshooting The monitor caused the problem of the Option board abnormal Please contact your supplier COh CFh abnormal of option board Sample The following examples are content of Alert Mail that informs the temperature anomaly of monitor From nec tarou jp nec com To nec hanako jp nec com Subject Monitor Monitor Information The nonitor is overheated If this continues please contact NEC for support Code lt ErrorCode gt Information Product Name X4618 serial Number 930PTOT2Y Hours Running ON 108 H Hours Running Total 262 H Sample The following examples are content of test mail by browser From nec tarou jp nec com To nec hanako jp nec com Subject Monitor Test Mail Alert Mail configurations are as follows Product Name 44618 serial Number 930PT012Y4 Sender s Address gt nec tarou jp nec com SMTP Server Name mail nec jp com Recipient s Address 1 nec hanako8jp nec com Recipient s Address 2 Recipient s Address 3 English 34 Features Reduced Footprint Provides the ideal solution for environments with superior image quality Color Control Systems Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards OmniColor Combines Six axis color control and the sRGB standard Six axis color control permits color adjustments via six axes R G B C M and Y rather tha
36. bjects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping or unstable cart stand or table as the monitor may fall causing serious damage to the monitor e Do not mount this product face up face down or upside down for an extended period of time as it may cause permanent damage to the screen e The power supply cord you use must have been approved by and comply with the safety standards of your country Type HO5VV F 3G 1mm should be used in Europe e In UK use a BS approved power cord with molded plug having a black 13A fuse installed for use with this monitor e Do not place any objects onto the monitor and do not use the monitor outdoors e The lamps in this product contain mercury Please dispose according to state local or federal law e Do not bend crimp or otherwise damage the power cord e f glass is broken handle with care e Do not cover vent on monitor e Do not use monitor in high temperature humid dusty or oily areas e f monitor or glass is broken do not come in contact with the liquid crystal and handle with care e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of the monitor e The power cable connector is the primary means of detaching the system from the power supply The monitor sh
37. ble to the eye in a variety of lighting conditions NOTE When picture mode is set to AMBIENT1 or AMBIENT2 BACKLIGHT AUTO BRIGHTNESS and BACKLIGHT in SCREEN SAVER function are disabled Do not cover Ambient light sensor when you use AMBIENT1 or AMBIENT2 in PICTURE MODE AMBIENT parameter setting PICTURE MODE in OSD select AMBIENT1 or AMBIENT2 and set IN BRIGHT and IN DARK in each mode IN BRIGHT This is the backlight level that the monitor will go up to when the ambient light level is highest IN DARK This is the level of backlight that the monitor will go down to when the ambient light level is low When the AMBIENT function is enabled the backlight level of the screen changes automatically according to the lighting conditions of the room Figure 1 Factory Setting 100 BACKLIGHT range BACKLIGHT level set for the monitor to use when ambient lighting level is low BACKLIGHT level set for the monitor to use when ambient lighting level is high y IN DARK IN BRIGHT 0 S dark room bright condition bright oeeseeeeeeceeeeeeo Screen Backlight value by AMBIENT1 mode Screen Backlight value by AMBIENT2 mode Figure 1 IN DARK BACKLIGHT level set for the monitor to use when ambient lighting level is low IN BRIGHT BACKLIGHT level set for the monitor to use when ambient lighting level is high English 18 OSD On Screen Display Controls NOTE Some functions may not be available depending on the model or optional
38. cific MONITOR ID number assigned to it 1 Set the MONITOR ID number for the display See page 23 The MONITOR ID number can range from 1 100 This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors 2 On the remote control press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number 1 100 The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled Choose 0 to simultaneously control all displays in range 3 Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button The MONITOR ID number is shown in red on the display If the REMOTE CONTROLID is 0 then all displays in range will show their respective MONITOR ID number in red If the MONITOR ID number is shown in white on the display the MONITOR ID number and the REMOTE CONTROL ID are not the same This LCD monitor can be controlled via personal computer or wireless remote control using an RS 232C connection MONITOR ID and IR CONTROL Using one PC or one infrared wireless controller up to 100 individual LCD monitors can be controlled through a daisy chain via RS 232C connection 1 Connect PC and LCD monitors Connect a PC s RS 232C control output to the LCD monitor RS 232C input You can then connect the RS 232C output from the LCD monitor to another LCD monitor RS 232C input Up to 100 monitors
39. condensation 90 3 5 x Temp 40 C regarding over 40 C 1250 2 W x 721 0 H x 141 5 D mm 49 2 W x 28 4 H x 5 6 D inches with handle 1250 2 W x 721 0 H x 125 4 D mm 49 2 W x 28 4 H x 4 9 D inches without handle 40 0 kg 88 2 lbs 400 mm x 400 mm M6 4 Holes VESA DPM VESA DDC2B DDC CI DisplayPort Setup manual Power Cord Video Signal cable Remote Control AA Battery x 2 Clamp x 3 Screw x 5 CD ROM Thumbscrew for optional stand x 2 Cable cover 1 Compressed image 2 Common terminal English 39 Pin Assignment 1 RS 232C input output D SUB 9P GND This LCD monitor uses RXD TXD and GND lines for RS 232C control GND 6 8 9 2 REMOTE IN GND DATA DC 3V VDD DC 3V 3 REMOTE OUT GND DATA DC 3 V English 40 Manufacturer s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company s top priorities in trying to minimize the burden placed on the environment We are engaged in developing environmentally friendly products and always strive to help define and comply with the latest independent standards from agencies such as ISO International Organisation for Standardization and TCO Swedish Trades Union Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re use upgrading reconditi
40. ct Choose Mark EXIT MAR daD Close priority over the schedule with the lowest number For example schedule 7 will have priority over schedule 1 If selected input or picture mode is not available now disable input or picture mode is shown in red NOTE 2 IMAGE PERSISTENCE Please be aware that LCD Technology may experience a phenomenon known as Image Persistence Image Persistence occurs when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image As with all personal display devices NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use Please set SCREEN SAVER DATE amp TIME and SCHEDULE SETTINGS functions to further reduce the risk of Image persistence For long life use as Public Display Image Sticking of LCD Panel When an LCD panel is operated continuously for long hours a trace of electric charge remains near the electrode inside LCD and residual or ghost image
41. de Picture out Picture mode Pe PoP Picture by picture split screen mode with keep aspect ASPECT Picture by picture split screen mode with full screen FULL Selects the size of the sub picture used in Picture in Picture PIP mode LARGE Determines where the PIP appears on the screen Enables Text Ticker and allows you to set Horizontal or Vertical direction Selects the location of the Text Ticker on the screen Determines the size of the Text Ticker in relationship to the overall screen size Sets the transparency of the Text Ticker 0 transparent 100 opaque Enables auto detection of the Text Ticker Enables fade in of the text ticker Selects sub picture input signal signal input RESET russe iP opto back to aio stings except ASPECT ara sue Neut OSD LANGUAGE Select the language used by the OSD ENGLISH Depends on ENGLISH destination DEUTSCH FRAN AIS ITALIANO ESPA OL SVENSKA PYCCKN x MENU DISPLAY TIME Turns off the OSD after a period of inactivity The preset choices are 10 240 seconds OSD POSITION Determines the location where the OSD appears on the screen X 128 Y 225 DOWN LEFT U RIGHT English 22 INFORMATION OSD Selects whether the information OSD is displayed or not The information OSD will be displayed when the input signal or source changes The information OSD will also give a warning when there is no signal or the signal is out of range
42. e Control s batteries status e Check if batteries are inserted correctly e Check if the Remote Control is pointing at the monitor s remote sensor e Check the Remote Control Mode status e The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor or when there is an object in the path SCHEDULE OFF TIMER function is not working properly e The SCHEDULE function will be disabled when the OFF TIMER is set e fthe OFF TIMER function is enabled and the power to the LCD monitor is turned off when the power supply is interrupted unexpectedly then the OFF TIMER will be reset Snowy Picture Poor Sound in TV e Check antenna cable connection Use new cable if necessary Interference in TV e Check components for shielding move away from monitor if necessary RS 232C or LAN control is not available e Check RS 232C or LAN cable connection e Check CONTROL setting in EXTERNAL CONTROL e Check the IDZALL REPLY setting in EXTERNAL CONTROL Either light vertical or horizontal stripes may appear depending on the specific display pattern This is no product fault or degradation English 36 Specifications P402 Product Specifications LCD Module Pixel Pitch Resolution Color Brightness Contrast Ratio Viewing Angle Frequency Horizontal Vertical Pixel Clock Viewable Size Input Signal
43. e same area a remote control in normal mode would send signals to every monitor at the same time see Figure 1 Using the remote in REMOTE CONTROL ID mode will only operate one specific Figure 1 monitor within the group see Figure 2 idis ormai mode or the REMOTE ID is set to O TO SET REMOTE CONTROL ID While holding down the REMOTE ID SET button on the remote control use the KEYPAD to input the Monitor ID 1 100 of the display to be controlled via remote The remote can then be used to operate the monitor having that specific Monitor ID number When 0 is selected or when the remote control is in normal mode all monitors will be operated Monitor IDM Monitor ID 2 Monitor ID 3 TO SET RESET REMOTE CONTROL MODE Remote does Remote does Remote works ID Mode To enter ID Mode press the REMOTE ID SET button and hold down for Bore oru 2 seconds Normal Mode To return to Normal Mode press the REMOTE ID CLEAR button and hold down for 2 seconds In order for this feature to work properly the display must be assigned a Monitor ID number Figure 2 The Monitor ID number can be assigned under the MULTI DISPLAY menu in the OSD Remote set up to use REMOTE See page 23 D3 Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button The MONITOR ID number is shown on the display when your remote control is in ID mode Use the remote control to operate a monitor that has a spe
44. edule number and press set The box next to the number will turn yellow The schedule can now be programmed 2 Use the down button to highlight the hours setting in the ON time slot Use the and buttons to set the hour Use the up and down buttons to highlight the minutes setting Use the and buttons to set the minutes Set the OFF time in the same manner 3 Use the up and down arrows to highlight INPUT Use the and buttons to choose the input source Use the up and down arrows to highlight PIC MODE Use the and buttons to choose the picture mode 4 Use the down button to select a day on which the schedule will be enabled Push the set button to enable If the schedule is to be ran every day choose EVERY DAY and press m LUE SCHEDULE the SET button The circle next to EVERY DAY will turn yellow If a weekly schedule is SCHEDULE THU JUN 182009 15 38 desired choose the days of the week using the up and down buttons and pressing SET OFF TIMER SETTINGS oe SCHEDULE SETTINGS e1 s2 e3 04 e5 e 7 to select Then highlight the EVERY WEEK option and press SET SCHEDULE LIST PO NEM OE DATE amp TIME OFF 5 After a schedule is programmed the remaining schedules can then be set Press MENU RENE INPUT PIC MODE to leave the OSD or press EXIT to go back to the previous menu amp EVERY DAY Note If schedules are overlapping then the schedule with the highest number will have S NON a TUE e WED s THU e FRI eSAT e SUN OQG Sele
45. elected in picture mode predefined 6500k is set so it cannot be changed GAMMA CORRECTION NATIVE except SRGB setting Select a display gamma for best picture quality Note When sRGB is selected in picture mode this function cannot be changed NATIVE Gamma correction is handled by the LCD panel Typical display gamma for use with a PC Good for video DVD etc S GAMMA Special gamma for certain types of movies Raises the dark parts and lowers the light parts of the image S Curve DICOM SIM DICOM GSDF curve simulated for LCD type PROGRAMMABLE A programmable gamma curve can be loaded using NEC optional software NOISE REDUCTION Adjusts the amount of noise reduction Press or to adjust VIDEO 1 VIDEO2 S VIDEO inputs only TELECINE Automatically senses the sources frame rate for optimal picture quality HDMI DVD HD SCART VIDEO1 VIDEO2 S VIDEO inputs only ADAPTIVE CONTRAST Sets the level of adjustment for dynamic contrast HDMI DVD HD SCART VIDEO1 VIDEO2 S VIDEO inputs only PICTURE MODE Selects picture mode HIGHBRIGHT STANDARD sRGB CINEMA AMBIENT 1 or STANDARD AMBIENT2 See page 18 D N A ND RESET Resets the following settings within the PICTURE menu back to factory setting BACKLIGHT CONTRAST SHARPNESS BRIGHTNESS HUE COLOR COLOR TEMPERATURE COLOR CONTROL GAMMA CORRECTION MOVIE SETTINGS ADJUST AUTO SETUP Automatically adjusts Screen Size H position
46. en a component failure is detected within the monitor the indicator will blink red If OFF is selected in POWER INDICATOR see page 23 LED will not light when the LCD monitor is in active mode AMBIENT LIGHT SENSOR Detects the level of ambient light allowing the monitor to make automatic adjustments to the brightness setting resulting in a more comfortable viewing experience Do not cover this sensor See page 18 Control Key Lock Mode This control completely locks out access to all Control Key functions To activate the control key lock function press both Ww and A and hold down simultaneously for more than 3 seconds To resume user mode press both W and A and hold simultaneously for more than 3 seconds English 7 Terminal Panel 20 dran HE 18 Out 00000 00000 1 AC IN connector Connects with the supplied power cord e9 Main Power Switch On Off switch to turn main power ON OFF Q LAN port RJ 45 LAN connection See page 31 REMOTE IN OUT Use the optional wired remote control by connecting it to your monitor NOTE When you use Remote IN OUT IR CONTROL in OSD menu should be NORMAL NOTE Do not use this connector unless specified RS 232C D Sub 9 pin IN connector Connect RS 232C input from external equipment such as a P
47. ensor and cooling fan If the LCD becomes too hot the cooling fan will turn on automatically If the LCD becomes overheated while the cooling fan is running a Caution warning will appear If the Caution warning appears discontinue use and allow the unit to cool Using the cooling fan will reduce the likelihood of early circuit failure and may help reduce image degradation and Image Persistance If the LCD is used in an enclosed area or if the LCD panel is covered with a protective screen please check the inside temperature of the monitor by using the HEAT STATUS control in the OSD see page 24 If the temperature is higher than the normal operating temperature please turn the cooling fan to ON within the FAN CONTROL menu within the OSD see page 24 IMPORTANT Lay the protective sheet which was wrapped around the LCD monitor when it was packaged beneath the LCD monitor so as not to scratch the panel 2 Install the remote control batteries The remote control is powered by two 1 5V AA batteries To install or replace batteries A Press and slide to open the cover B Align the batteries according to the and indications inside the case C Replace the cover CAUTION Incorrect usage of batteries can result in leaks or bursting NEC recommends the following battery use e Place AA size batteries matching the and signs on each battery to the and signs of the batte
48. equipment Main Menu Item ani BACKLIGHT CONTRAST SHARPNESS BRIGHTNESS HUE COLOR COLOR TEMPERATURE COLOR CONTROL GAMMA CORRECTION MOVIE SETTINGS PICTURE MODE RESET Sub Menu Adjustment Settings THANK YOU FOR SAVING THE ENVIRONMENT CARBON FOOTPRINT 86 0 Key Guide Press UP or DOWN Press SET button to select sub menu MENU MENU Remote Control 4e EXIT EXIT Press INPUT button to decide Press UP or DOWN button to select Control Panel EXIT v Fy 3 EC i exa AUDIO SCHEDULE PIP I MULTI DSP PROTECT ADVANCED PICTURE BACKLIGHT CONTRAST SHARPNESS BRIGHTNESS OSD screen HUE COLOR COLOR TEMPERATURE COLOR CONTROL GAMMA CORRECTION MOVIE SETTINGS PICTURE MODE RESET IARTA ETS ALW SET MGR REA EXIT MENU LO Loy English 19 Press UP or DOWN PLUS or MINUS to select the function or setting to be adjusted Eu ES Press MENU or EXIT EXIT Press UP or DOWN PLUS Press EXIT or MINUS button to select INPUT MUTE b PD ro ER ence PICTURE REA gs BU eRe este URS N21 OSD MULTI DSP PROTECT ADVANCED PICTURE BACKLIGHT CONTRAST SHARPNESS BRIGHTNESS HUE COLOR COLOR TEMPERATURE COLOR CONTROL GAMMA CORRECTION MOVIE SETTINGS PICTURE MODE RESET THANK YOU FOR SAVING THE ENVIRONMENT CARBON FOOTPRINT 86 0 OG Select OGED Goto Adjustment G MD Return D Close Setting Default PICTURE BACKLIGHT Adjusts
49. g mounting accessories other than those that are NEC approved they must comply with the VESA compatible FDMIv1 mounting method e NEC strongly recommends Unit No gap Mounting using size M6 screws Pd Bracket 11 12 mm thickness Washer of bracket and washer in length If using screws LU 3Screw longer than 11 12 mm Poem check the depth of the hole Thickness Recommended Fasten es Force 470 635Necm Screw length should equal NEC recommends mounting depth of hole 11 12 mm the interfaces that comply with UL 1678 standard in North America thickness of mounting bracket and washer Bracket hole should be under 8 5 mm e Prior to mounting inspect the installation location to insure that it is strong enough to support the weight of the unit so that the unit will be safe from harm e Refer to the instructions included with the mounting equipment for detailed information e Make sure there is no gap between the monitor and the bracket Orientation e When using the monitor in the portrait position the monitor should be rotated clockwise so that the left side is moved to the top and the LED indicator light is on the bottom This will allow for proper ventilation and will extend the lifetime of the monitor Improper ventilation may shorten the lifetime of the monitor LED Indicator Mounting location e The ceiling and wall must be strong enough to support the monitor and moun
50. ich has BSMI mark at both ends when you use this monitor in Taiwan Declaration Declaration of the Manufacturer We hereby certify that the color monitor MultiSync P402 and marked with LA00U5 MultiSync P462 L460U6 MultiSync P552 P552 are in compliance with Council Directive 2006 95 EC EN 60950 1 ND 2004 108 EC NEC Display Solutions Ltd 4 13 23 Shibaura EN 61000 3 2 Minato Ku EN 61000 3 3 _ EN 55024 Tokyo 108 0023 Japan Council Directive 2009 125 EC EC No 642 2009 EN 62301 2005 e The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment e The product is intended to be connected to a computer and is not intended for the display of television broadcast signals English 2 Safety Precautions Maintenance amp Recommended Use FOR OPTIMUM PERFORMANCE PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTI FUNCTION MONITOR e DO NOT OPEN THE MONITOR There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy o
51. ide image area will be cut off due to expansion 1 1 Display the image in a 1 by 1 pixel format ZOOM The image can be expanded beyond the active display area The image which is outside of active display area is not shown px tense English 17 Information OSD The Information OSD provides information such as Monitor ID Input Source Picture Size etc Press the DISPLAY button on the remote to bring up the Information OSD ID number assigned to current monitor Monitor ID 1 DVI Target ID 5 AUDIO IN1 ASPECT FULL ID number assigned monitor to be controlled via RS 232C Input Name Audio input mode Q Picture aspect 1024 X 768 48KHz 60Hz 000 Input Signal Information Sub picture information E18 A1 e NTSC 1 IR CONTROL should be set Primary or Secondary 2 IR CONTROL should be set Primary Picture Mode DVI VGA RGB HV DPORT STANDARD sRGB AMBIENT1 AMBIENT2 HIGHBRIGHT fe HDMI DVD HD SCART VIDEO 1 VIDEO2 S VIDEO STANDARD CINEMA AMBIENT1 AMBIENT2 HIGHBRIGHT e AMBIENT Mode The backlight of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room If the room is bright the monitor becomes correspondingly bright If the room is dim then the monitor will dim accordingly The purpose of this function is to make the viewing experience more comforta
52. ings by using an HTTP server function NOTE When you use this function EXTERNAL CONTROL should be LAN See page 23 To use a LAN connection you are required to assign an IP address Example of LAN connection Server NOTE Use a category 5 or higher LAN cable LAN cable not supplied Network Setting by Using an HTTP Browser Overview Connecting the monitor to a network allows for monitor control from a computer via the network To perform the monitor control from a web browser you must have an exclusive application installed on your computer The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP server function Please be sure to use Microsoft Internet Explorer 6 0 or a higher version for the web browser This device uses JavaScript and Cookies and the browser should be set to accept these functions The setting method will vary depending on the version of browser Please refer to the help files and the other information provided in your software Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the monitor and entering the following URL Network Setting http lt the Monitor s IP address gt index html TIP The default IP address is 192 168 0 10 The exclusive application can
53. ironment Temperature Humidity Dimension Weight VESA compatible mounting interface Power Management Plug amp Play Accessories NOTE Technical specifications are subject to change without notice 46 1168 mm diagonal 0 530 mm 1920 x 1080 Over 16 million colors depending on video card used 650 cd m Max 500 cd m Factory setting Typ 25 C 3500 1 89 typ CR gt 10 15 625 15 734 kHz 31 5 KHz 91 1 kHz Analog Input 31 5 kHz 91 1 kHz Digital Input 50 0 85 0 Hz 25 2 MHz 162 0 MHz 1018 1 x 572 7 mm DVI HDCP VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz 1080p 1080i DisplayPort Complies with Standard V1 1a applicable to HDCP V1 3 VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920x1080 60 Hz 1080p 720p 0 7 Vp p 75 ohm VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz Separate TTL level Pos Neg Composite sync on Green Video 0 3 Vp p Neg 0 7 Vp p 75 ohm VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGAG60 1920X1080 60Hz Separate TTL level Pos Neg Composite sync on Green Video 0 3 Vp p Neg HDMI VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920x1080 60 Hz 1080p 1080i 720p 50Hz 60Hz 576p 9 50Hz 480p 60Hz 576i 50Hz 480i 60Hz Y 1 0 Vp p 75ohm Cb Cr Pb Pr 0 7 Vp p 75 ohm HDTV DVD 1080p 1080i 720p Q9 50Hz 60Hz 576p 50Hz 480p 60Hz 576i 50Hz 480i 60Hz 1 0 Vp p 75 ohm NTSC PAL SECAM 4 43NTSC PAL60 Y
54. ith a soft cloth e To clean the cabinet dampen the cloth with a neutral detergent and water wipe the cabinet and follow with a dry cloth NOTE DO NOT clean with benzene thinner alkaline detergent alcoholic system detergent glass cleaner wax polish cleaner soap powder or insecticide Rubber or vinyl should not be in contact with the cabinet for an extended period of time These types of fluids and materials can cause the paint to deteriorate crack or peel The product you purchased may not have this feature English 3 Contents Your new MultiSync monitor box should contain the following e CD monitor e Cable cover e Power cord e Clamp x 3 e Video Signal Cable e Screw M4 x 10 x5 e Wireless Remote Control and AA Batteries e CD ROM e Setup Manual e Thumbscrew for optional stand x 2 Video Signal Cable Mini D SUB 15 pin to Mini D SUB 15 pin Om O Screw M4 x 10 x 5 Thumbscrew for Power Cord optional stand x 2 Cable cover P402 P462 Cable cover P552 LL Setup Manual CD ROM 2 Setup Manual Wireless Remote Control and AA Batteries Remember to save your original box and packing material to transport or ship the monitor Type and number of power cords included will depend on the where the LCD monitor is to be shipped When more than one power cord is included please use a power cord that matches the AC voltage of the power outlet and has been app
55. ke certain the computer is not in a power saving mode touch the keyboard or mouse e Check to see that the power indicator option in the OSD is set to ON RED LED on monitor is blinking e A certain failure might have occurred please contact your nearest authorized NEC DISPLAY SOLUTIONS service facility e If the monitor is powered off by the inside temperature being higher than the normal operating temperature a RED LED will blink six times Power on the display again after confirming the inside temperature has been reduced to normal operation temperature Display image is not sized properly e Use the OSD Image Adjust controls to increase or decrease the coarse adjustment e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode Selected resolution is not displayed properly e Use OSD Display Mode to enter Information menu and confirm that the appropriate resolution has been selected If not select corresponding option No Sound e Check to see if audio cable is properly connected e Check to see if mute is activated e Check to see if volume is set at minimum e Check to see if computer supports an audio signal through DisplayPort If unsure contact the computer manufacturer e Check to see if SURROUND is ON e Check Internal External speaker switch Remote Control is not available e Check the Remot
56. l Pixel Clock Viewable Size Input Signal DVI D 24pin Digital RGB DisplayPort DisplayPort Connector Digital RGB 15pin Mini D sub Analog RGB Sync RGB HV BNC R G B H V Analog RGB Sync HDMI HDMI Connector Digital YUV Digital RGB Component DVD HD BNC X3 VIDEO1 BNC Composite VIDEO2 BNC S VIDEO Mini DIN 4 pin S VIDEO Ms Signal DVI D 24pin Digital RGB DisplayPort E Connector Digital RGB AUDIO AUDIO RCA L R Analog Audio Input STEREO Mini Jack X2 HDMI Connector Digital Audio AUDIO STEREO Mini Jack Analog Audio Output Speaker Output Control RS 232C In RS 232C Out LAN Remote IN Remote OUT Power Supply Operational Environment Temperature Humidity Altitude Storage Environment Temperature Humidity Dimension Weight VESA compatible mounting interface Power Management Plug amp Play Accessories NOTE Technical specifications are subject to change without notice 54 6 1387 8 mm diagonal 0 630 mm 1920 x 1080 Over 16 million colors depending on video card used 700 cd m Max 500 cd m Factory setting Typ 25 C 4000 1 89 typ CR gt 10 15 625 15 734 kHz 31 5 KHz 91 1 kHz Analog Input 31 5 kHz 91 1 kHz Digital Input 50 0 85 0 Hz 25 2 MHz 162 0 MHz 1209 6 x 680 4 mm DVI HDCP VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz 1080p 1080i DisplayPort Complies with Standard V1 1a applicable to HDCP V1 3 VGA60 SVGA60 XGA60 WX
57. m L 3 ES o 00000 o gg Stereo Amplifier DVD player with SCART OUT Second monitor baec 82 LEON 1 ot l o 2 i J d ON c O __ Z CbA ENT UT NS OUT A DVD player VCR or with HDMI out DVD Player DVD player Computer Digital Multiple monitors that are daisy chained have a limit to the connectable monitors NOTE Solid lines video signal Dotted lines audio signal ro sonnaceng Setting in Terminal Mode Input signal name POHBACURS input button equipment terminal Audio terminal in remote control DVI DVI D DVI MODE DVI HD AUDIO IN1 IN2 IN3 HDMI RAW EXPAND HDMI HDMI HDMI 5BNC VIDEO BNC MODE SCART SCART AUDIO IN1 IN2 IN3 DVD HD AV S VIDEO BNC MODE VIDEO BNC MODE COMPONENT DVI MODE DVI PC BNC MODE RGB DPORT DISPLAYPORT RAW EXPAND 1 depend on signal type e AUDIO IN 1 2 and 3 can be used for audio input To select audio source IN1 IN2 or IN3 in AUDIO INPUT in OSD menu or press the AUDIO INPUT button remote control English 14 Connecting a Personal Computer Connecting your computer to your LCD monitor will enable
58. mit depending on the cable you use Z O COPY START Select YES and press the SET button to start copying ALL INPUT All input terminals settings are copied when you select this item Default is off Resets MULTI DISPLAY options back to factory settings except LAN SETTING RESET DISPLAY PROTECTION POWER SAVE O Z Sets how long the monitor waits to go into power save mode after the signal is lost Note When connecting DVI the video card might not stop sending the digital data even though the image might have disappeared If this occurs the monitor will not switch into power management mode HEAT STATUS Displays status of the FAN BACKLIGHT and TEMPERATURE FAN CONTROL Cooling fan reduces the temperature of the display to protect from overheating AUTO If AUTO is selected you can adjust the start temperature of the cooling fan and fan speed SCHEEN SAVER Use the SCREEN SAVER function to reduce the risk of Image Persistence GAMMA The display gamma is changed and fixed when ON is selected OFF BACKLIGHT The brightness of backlight is decreased when ON is selected OFF NOTE Do not select this function when picture mode is AMBIENT1 or AMBIENT2 MOTION The screen image is slightly expanded and moves in 4 directions UP DOWN RIGHT LEFT at OFF user determined intervals You can set interval time and zooming ratio This function is disabled when PIP STILL TEXT TICKER or TILE MATRIX a
59. monitor does not operate normally by following operating instructions Recommended Use e For optimum performance allow 20 minutes for warm up e Rest your eyes periodically by focusing on an object at least 5 feet away Blink often e Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections e Clean the LCD monitor surface with a lint free non abrasive cloth Avoid using any cleaning solution or glass cleaner e Adjust the monitor s brightness contrast and sharpness controls to enhance readability e Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects e Get regular eye checkups Ergonomics To realize the maximum ergonomic benefits we recommend the following e Use the preset Size and Position controls with standard signals e Use the preset Color Setting e Use non interlaced signals e Do not use primary color blue on a dark background as it is difficult to see and may produce eye fatigue due to insufficient contrast Cleaning the LCD Panel e When the liquid crystal panel is dusty please gently wipe with a soft cloth e Please do not rub the LCD panel with hard material e Please do not apply pressure to the LCD surface e Please do not use OA cleaner as it will cause deterioration or discolor on the LCD surface Cleaning the Cabinet e Unplug the power supply e Gently wipe the cabinet w
60. n through the three axes R G and B previously available The sRGB standard provides the monitor with a uniform color profile This assures that the colors displayed on the monitor are exactly the same as on the color printout with SRGB supporting operating system and sRGB printer This allows you to adjust the colors on your screen and customise the color accuracy of your monitor to a variety of standards SRGB Color Control A new optimized color management standard which allows for color matching on computer displays and other peripherals The sRGB standard which is based on a calibrated color space allows for optimal color representation and backward compatibility with other common color standards OSD On Screen Display Controls Allow you to quickly and easily adjust all elements of your screen image via simple to use on screen menus Plug and Play The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor to send its capabilities such as screen size and resolutions supported directly to your computer automatically optimizing display performance IPM Intelligent Power Manager System Provides innovative power saving methods that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy costs reducing emissions and lowering the air conditioning costs of the workplace FullScan Capability Allows you to use
61. network connected to the monitor when DISABLE is selected for DHCP Subnet Mask Set your subnet mask number of the network connected to the monitor when DISABLE is selected for DHCP Default Gateway Set your default gateway of the network connected to the monitor when DISABLE is selected for DHCP Primary DNS Set your primary DNS settings of the network connected to the monitor Secondary DNS Set your secondary DNS settings of the network connected to the monitor Apply Reflect your settings NOTE Make sure to execute the reboot from the reboot screen or to turn the monitor off and then back on to enable the changing after clicking Apply NOTE The following settings will reset back to the factory setting when LAN reset is selected by an EXTERNAL CONTROL of OSD DHCP DISABLE IP v4 Address 192 168 0 10 Subnet Mask 255 255 255 0 Default Gateway 192 168 0 1 but Primary DNS and Secondary DNS are not changed English 32 Alert Mail Setting http lt the Monitor s IP address gt lanconfig html Mail Setting Alert Mail Enable Disable Host Name Domain Name Sender s Address SMTP Server Recipient s Address1 Recipient s Address2 Recipient s Address3 Authentication Method POP3 Server User Name Password Copyright NEC Display Solutions Ltd 2010 All rights reserved This option notifies your computer of an error mess
62. of previous image may be observed Image Persistence Image Persistence is not permanent but when fixed image is displayed for long period ionic impurities inside LCD are accumulated along the displayed image and may be permanent Image Sticking Recommendations To prevent Image Sticking and for longer life usage of LCD the following are recommended 1 Fixed image should not be displayed for long period Change fixed images after short intervals 2 When not in use please turn off the monitor by remote control or use Power Management or use Schedule Functions 3 Lower environmental temperatures prolong the lifespan of the monitor When Protective surface glass acrylic is installed over the LCD surface the LCD surface is located in an enclosed space the monitor are stacked utilize the temperature sensors inside monitor To reduce the environmental temperature use the Cooling Fan Screen Saver and Low Brightness 4 Please use Screen Saver Mode of monitor English 27 Remote Control Function REMOTE CONTROL ID FUNCTION REMOTE CONTROL ID The remote control can be used to control up to 100 individual MultiSync monitors using Monitor ID 1 Monitor ID 2 Monitor ID 3 what is called the REMOTE CONTROL ID mode The REMOTE CONTROL ID mode melios EERORNOIE distet Les works in conjunction with the Monitor ID allowing control of up to 100 individual MultiSync monitors For example if there are many monitors being used in th
63. on s action depends on which option board you use Refer to the option board s manual for further information Operating Range for the Remote Control Point the top of the remote control toward the LCD monitor s remote sensor during button operation Use the remote control within a distance of about 7 m 23 ft from remote control sensor or at a horizontal and vertical angle of within 30 within a distance of about 3 5 m 10 ft Caution Handling the remote control e Do not subject to strong shock Important the remote control system may not function when direct sunlight or strong vx 7 illumination strikes the remote control sensor or when there is an object in the path e Do not allow water or other liquid to splash the remote control If the remote control gets wet wipe it dry immediately e Avoid exposure to heat and steam e Other than to install the batteries do not open the remote control English 11 Setup 1 Determine the installation location CAUTION Installing your LCD monitor must be done by a qualified technician Contact your dealer for more information CAUTION MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE P402 P462 BY FOUR OR MORE PEOPLE P552 Failure to follow this caution may result in injury if the LCD monitor falls CAUTION Do not mount or operate the monitor upside down face up or face down CAUTION This LCD has a temperature s
64. oning or reclamation of material Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed To ensure the best recycling of our products NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way once it has reached the end of its life All required information concerning the disposal of the product and country specific information on recycling facilities can be found on our following websites http www nec display solutions com greencompany in Europe http www nec display com in Japan or http www necdisplay com in USA Energy Saving This monitor features an advanced energy saving capability When a VESA Display Power Management Signalling DPMS Standard signal is sent to the monitor the Energy Saving mode is activated The monitor enters a single Energy Saving mode Approx 145 W P402 Normal Operation Approx 155 W P462 Green Approx 265 W P552 Energy Saving Mode Less than 1 W Power Off Lessthan05W Red 1 without any option with factory settings 2 VGA input only WEEE Mark European Directive 2002 96 EC Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors
65. orrect Apply Click this button to reflect the above settings NOTE Make sure to execute the reboot from the reboot screen or to turn the monitor off and then back on to enable the changing after clicking Apply NOTE f you execute a test you may not receive an Alert mail Should this happen check if the network settings are correct e f you entered an incorrect address in a test you may not receive an Alert mail Should this happen check if the Recipient s Address is correct TIP The Alert Mail settings will not be affected even when RESET is done from the menu For Control command diagram please see file External Control pdf on the CD ROM English 33 Alert error message list Error number r 70h 7Fh The monitor s power supply is not Standby power Abnormal Please contact your supplier functioning normally 80h Fh The cooling fan has stopped Cooling fan Abnormal Please contact your supplier 90h 9Fh The monitor s back light unit is not Backlight abnormal Please contact your supplier functioning normally AOh AFh The monitor is overheated Temperature Abnormal Please contact your supplier SENSOR reached at the temperature Reconfirm the setting condition from that the user had specified OSD DISPLAY PROTECTION FAN condition DISPLAY PROTECTION FAN ET or please contact your CONTROL COOLING FAN AUTO The monitor doesn t have the input No signal Please check No picture in BOh BFh 2 N
66. ot appear e Select DisplayPort cables feature a locking function When removing this cable hold down the top button to release the lock e When you connect a second monitor via DisplayPort out allows to show 3840 x 1080 images However it depends on video card s capability English 15 Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off NOTE The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD OFF D Main Power Switch ON Power Button Using the remote control X 30 30 ene oon Pry rd jo a z EE REF OG 3 ez English 16 Power Indicator Power OFF Power consumption under 0 5 W Power Save Power consumption under 1 W Amber Power Standby when SCHEDULE Green and Amber blink alternately SETTINGS enabled Diagnosis Detecting failure Red Blinking See Troubleshooting page 36 1 If OFF is selected in POWER INDICATOR page 23 the LED will not light when the LCD monitor is in active mode 2 Without any option with factory settings VGA input only Using Power Management The LCD monitor follows the VESA approved DPM Display Power Management function The power management function is an energy saving function that automatically reduces the power consumption
67. ould be installed close to a power outlet which is easily accessible e Do not move or mount this product by hanging a rope or wire to the backside handle Do not mount or secure this product by using the backside handle It may fall and cause personal injury e Handle with care when transporting Save packaging for transporting e f using the cooling fan continuously it is recommended to wipe holes clean a minimum of once a month e Please clean the holes of back cabinet to reject dirt and dust at least once a year because of set reliability e When using a LAN cable do not connect to a peripheral device with wiring that might have excessive voltage Connecting to a TV e Cable distribution system should be grounded earthed in accordance with ANSI NFPA 70 the National Electrical Code NEC in particular Section 820 93 Grounding of Outer Conductive Shield of a Coaxial Cable e The screen of the coaxial cable is intended to be connected to earth in the building installation Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e If liquid has been spilled or objects have fallen into the monitor e If the monitor has been exposed to rain or water e If the monitor has been dropped or the cabinet damaged e f you notice any structural damage such as cracks or unnatural wobbling e If the
68. pared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 Windows is a registered trademark of Microsoft Corporation NEC is a registered trademark of NEC Corporation OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland DisplayPort is trademarks of Video Electronics Standards Association B All other brands and product names are trademarks or registered trademarks of their respective owners ADI HIGH DEFINITION MULTIMEDIA INTERFACE HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries ENERGY STAR As an ENERGY Star Partner NEC Display Solutions of America Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency The ENercy Star emblem does not represent EPA endorsement of any product or service English 1 Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICI
69. put the audio signal from the AUDIO IN 1 2 3 and HDMI to an external device stereo receiver amplifier etc D S VIDEO IN connector Mini DIN 4 pin To input the S video Y C separate signal D auno IN 1 2 3 To input audio signal from external equipment such as a computer VCR or DVD player EXTERNAL SPEAKER TERMINAL To output the audio signal from AUDIO 1 2 3 and HDMI Red terminal is plus Black terminal is minus Note This speaker terminal is for 15W 15W 8 ohm speaker English 8 17 Internal External speaker switch Switch to turn internal speaker external speaker LL Internal speaker LL External speaker NOTE Please power off the monitor when you use the Internal External speaker switch 18 Kensington Lock For security and theft prevention Option board slot Slot 1 and slot 2 type accessories are available Please contact your supplier for detailed information NOTE Please contact your supplier for available option board NOTE When you use slot 2 type option board you need to install it with the optional SB 02AM adapter e Internal speaker BNC input signal RGB HV DVD HD VIDEO2 SCART English 9 Wireless Remote Control DVI PORT VGA RGB HV HDMI DVD HD VIDEO S VIDEO MODE ASPECT SOUND J OPTION REMOTE CONTROLLER RU M117 POWER button Switches the power on standby INPUT button Selects input signal DVI DVI DISPLAY PORT
70. r within an RS 232C daisy chain SECONDARY Choose SECONDARY for all subsequent monitors within an RS 232C daisy chain LOCK Prevents the monitor from being controlled by the wireless remote controller To return to normal operation press the DISPLAY button on the remote controller for 5 seconds TILE MATRIX Allows one image to be expanded and displayed over multiple screens up to 100 through a distribution amplifier NOTE Low resolution is not suitable for tiling to a large number of monitors You can operate without a distribution amplifier at a lower number of screens The ZOOM setting of ASPECT becomes invalid POWER ON DELAY Adjusts the delay time between being in standby mode and entering power on mode 0 Sec POWER ON DELAY can be set between 0 and 50 seconds POWER INDICATOR Turns ON or OFF the LED located at the front of the monitor If OFF is selected LED will not light when the LCD monitor is in active mode EXTERNAL CONTROL CONTROL Selects the control interface RS 232C or LAN LAN RESET Resets the LAN settings ID ALL REPLY When controlling the monitor externally select if the communication command which specifies OFF destination equipment ID ALL or GROUP ID is replying or not When you need reply please LANDSCAPE Z NORMAL O zZ RS 232C select ON If you connect the multiple monitors that are daisy chained from second monitor by RS 232C you need to select O
71. re enabled SIDE BORDER COLOR Adjusts the color of the side borders when a 4 3 image is displayed Press button the bar will become lighter Press button the bar will become darker C1 O 7 AUTO BRIGHTNESS DPORT DVI VGA RGB HV inputs only Adjusts the brightness level according to the input signal NOTE Do not select this function when picture mode is AMBIENT1 or AMBIENT2 PASSWORD The factory preset password is 0000 ALERT MAIL Selects whether or not to send an e mail notification of monitor error via wired LAN OFF RESET Resets the following settings within the DISPLAY PROTECTION menu back to factory setting POWER SAVE FAN CONTROL SCREEN SAVER SIDE BORDER COLOR AUTO BRIGHTNESS DDC CI English 24 ADVANCED OPTION INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices are NONE connected NONE The Monitor will not search the other video input ports FIRST DETECT When the current video input signal is not present then the monitor searches for a video signal from the other video input port If the video signal is present in the other port then the monitor switches the video source input port to the new found video source automatically The monitor will not look for other video signals while the current video source is present LAST DETECT When the monitor is displaying a signal from the current source and a new secondary source is
72. roved by and complies with the safety standard of your particular country English 4 Installation This device cannot be used or installed without the Tabletop Stand or other mounting accessory for support For proper installation it is strongly recommended to use a trained NEC authorized service person Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer Product warranty does not cover damage caused by improper installation Failure to follow these recommendations could result in voiding the warranty Mounting DO NOT mount the monitor yourself Please ask dealer For proper installation it is strongly recommended to use a trained qualified technician Please inspect the location where the unit is to be mounted Mounting on wall or ceiling is the customer s responsibility Not all walls or ceilings are capable of supporting the weight of the unit Product warranty does not cover damage caused by improper installation remodelling or natural disasters Failure to comply with these recommendations could result in voiding the warranty DO NOT block ventilated openings with mounting accessories or other accessories For NEC Qualified Personnel To ensure safe installation use two or more brackets to mount the unit Mount the unit to at least two points on the installation location Please note the following when mounting on wall or ceiling e When usin
73. ry compartment e Do not mix battery brands e Do not combine new and old batteries This can shorten battery life or cause liquid leakage of batteries e Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment e Do not touch exposed battery acid it may injure skin NOTE If you do not intend to use the Remote Control for a long period of time remove the batteries 3 Connect external equipment See pages 14 and 15 e To protect the external equipment turn off the main power before making connections e Refer to your equipment user manual for further information NOTE Do not connect disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image 4 Connect the supplied power cord The equipment should be installed close to an easily accessible power outlet e Please fasten power cord to the LCD monitor by attaching the screw and clamp e Fully insert the prongs into the power outlet socket A loose connection may cause image degradation NOTE Please refer to the Safety Precautions and Maintenance section of this manual for proper selection of AC power cord English 12 5 Attach the cable cover Use two of the MA screws included to attach the cable cover
74. so as not to interfere with radio and television reception 1 Please use the supplied power cord or equivalent to ensure FCC compliance 2 Please use the supplied shielded video signal cable Mini D SUB 15 pin to Mini D SUB 15 pin 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult your dealer or an experienced radio TV technician for help If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet pre
75. splay via that registered host name using a compatible browser If the host name corresponding to the IP address of the monitor has been configured in the HOSTS file of the computer being used you can then access the network settings of the display via that host name using a compatible browser Example 1 When the host name of the monitor has been set to pd nec co jp access is gained to the network setting by specifying http pd nec co jp index html for the address or the entry column of the URL Example 2 When the IP address of the monitor is 192 168 73 1 access is gained to the mail alert settings by specifying http 192 168 73 1 index html for the address or the entry column of the URL Network Settings http lt the Monitor s IP address index html NEC Home SNMP Reboot IP v4 Settings DHCP Q Enable 9 Disable IP v4 Address 172 16 205 40 Subnet Mask 255 255 248 0 Default Gateway 172 16 200 1 Primary DNS 0 0 0 0 Secondary DNS 0 0 0 0 i m Copyright NEC Display Solutions Ltd 2010 All rights reserved Enabling this option automatically assigns an IP address to the monitor from your DHCP server Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator NOTE Consult your network administrator for the IP address when ENABLE is selected for DHCP IP v4 Address Set your IP address of the
76. supplied to the monitor the monitor will automatically switch to the new video source When current video input signal is not present the monitor searches for a video signal from the other video input port If the video signal is present in the other port then the monitor switches the video source input port to the new found video source automatically VIDEO DETECT DVD HD SCART VIDEO1 VIDEO2 or S VIDEO inputs will have priority over DVI VGA RGB HV When DVD HD SCART VIDEO1 VIDEO2 or S VIDEO input signal is present the monitor will change and keep to the DVD HD SCART VIDEO1 VIDEO2 or S VIDEO input CUSTOM DETECT Set the priority of input signals When CUSTOM DETECT is selected monitor searches listed inputs only INPUT CHANGE Sets input change speed NORMAL NOTE When QUICK is selected picture may be distorted when signal input is changed This function should be chosen after all adjustment options have been made for the input DVI MODE Selects the kind of DVI D equipment which is connected to the DVI input Select DVI PC when DVI PC PC or other computer equipment is connected Select DVI HD when DVD player which has DVI D output is connected Selects the type of signal associated with the BNC input HGB RGB Analog input R G B H V COMPONENT Component Y Cb Pb Cr Pr SCART SCART signal VIDEO Composite video VIDEO2 N BNC MODE HDMI SIGNAL RAW Disable the expanded feature EXPAND EXPA
77. the entire screen area in most resolutions significantly expanding image size VESA Standard FDMIv1 Mounting Interface Allows you to connect your LCD monitor to any VESA standard FDMIv1 third party mounting arm or bracket NEC recommends using mounting interface that comply with TUV GS and or UL1678 standard in North America DVI D The digital only subset of DVI ratified by the Digital Display Working Group DDWG for digital connections between computers and displays As a digital only connector analog support is not provided for a DVI D connector As a DVI based digital only connection only a simple adapter is necessary for compatibility between DVI D and other DVI based digital connectors such as DFP and P amp D The DVI interface of this display supports HDCP TILE MATRIX TILE COMP Shows one image over multiple screens with accuracy while compensating for bezel width ZOOM Expands image size for horizontal and vertical direction RS 232C daisy chain You can control the multiple monitors by controller or wireless remote controller Self diagnosis If an internal error should occur a failure state will be indicated HDCP High bandwidth Digital Content Protection HDCP is a system for preventing illegal copying of video data sent over a Digital Visual Interface DVI If you are unable to view material via the DVI input this does not necessarily mean the display is not functioning properly With the implementation of HDCP there may be
78. ting accessories e DO NOT install in locations where a door or gate can hit the unit e DO NOT install in areas where the unit will be subjected to strong vibrations and dust e DO NOT install near where the main power supply enters the building e Do not install in where people can easily grab and hang onto the unit or the mounting apparatus e When mounting in a recessed area as in a wall leave at least 4 inches 100 mm of space between the monitor and the wall for proper ventilation e Allow adequate ventilation or provide air conditioning around the monitor so that heat can properly dissipate away from the unit and mounting apparatus Mounting on ceiling e Ensure that the ceiling is sturdy enough to support the weight of the unit and the mounting apparatus over time against earthquakes unexpected vibrations and other external forces e Be sure the unit is mounted to a solid structure within the ceiling such as a support beam Secure the monitor using bolts spring lock washers washer and nut e DO NOT mount to areas that have no supporting internal structure DO NOT use wood screws or anchor screws for mounting DO NOT mount the unit to trim or to hanging fixtures Maintenance e Periodically check for loose screws gaps distortions or other problems that may occur with the mounting apparatus If a problem is detected please refer to qualified personnel for service e Regularly check the mounting location

NEC P402-TMX4P

Contents

Download Pdf Manuals

Related Search

Related Contents