Home
Exposure 3010s2
Contents
1. are NO user serviceable parts inside except to install or change a phono card e Set the volume control to minimum before turning this unit on or off e Ensure that this unit is switched off when connecting or disconnecting speaker and interconnect cables Contact your Exposure dealer or distributor for advice on moving your equipment to another country or territory Caution For a long and trouble free life of your Exposure 301052 Integrated Amplifier please ensure the following e Do not short circuit the speaker terminals e Do not remove the cover of the Integrated Amplifier or dismantle the case except to Install or change phono card e Protect unit against all forms of liquid Never expose unit to dripping or splashing or place objects filled with water such as vases on the unit e Do not operate the Integrated Amplifier in damp environments or allow liquids to enter the unit e Do not attempt to bypass the mains fuse or replace the fuse with one of a different specification e Do not place the Integrated Amplifier in a position which restricts cooling airflow around its case e Do not use abrasive or solvent based cleaning fluids on the Integrated Amplifiers case Failure to observe these precautionary measures may void your warranty Technical Specifications Power Output 1O Watts per channel at KHz into 8 Ohms Input Impedance ZK Ohms minimum line input Input Sensitivity 250mV V for rated
2. knobs will rotate to match selections made on remote control Please check the contents in the box TAPE REC Provides line level output signals for recording o aa Inputs PRE OUT Provides left and right channel output signals appropriate Grey Buttons 5 for connection to an Exposure 3010S2 Power Amplifier E eet artes a Connect RCA Phono cables from each source component a future proof upgrade Exposure CD player if any CD Player Tuner Tape Disc Recorder Turntable Video Player Exposure 3010S2 Integrated Amplifier HS 101 Exposure System remote control 2 x AAA batteries Mains cable Ensure your unit is switched off and that the volume control knob is at ts minimum Please note that your Exposure 301052 Integrated Amplifier may take up to 48 hours to run in before reaching its optimal performance Each subsequent run in will then take about 20 minutes The Exposure 301052 Integrated Amplifier is equipped with a heat sensor which will automatically switch off the power amplifier section when an abnormally high temperature is reached To reset the output switch off the amplifier and allow to cool for 10 to 5 minutes to the respective input 3 Loudspeaker Connections Left Speak b Ensure left and right channels are connected correctly eee Right channel is marked in red SU a c The tape input is labeled TAPE PLAY Back view of exposure 301 0S2 I
3. aims under this warranty The unit should be surtably packed and returned to the dealer from whom it was purchased or directly to the local distributor together with proof of purchase or a copy of the dated sales receipt 2 f necessary the unit should be sent carriage pre paid by a reputable carrier NOT by post 3 No responsibility is accepted for the unit whilst on transit to the dealer or agent and customers are advised to insure the unit against loss or damage whilst in transit 4 The warranty card MUST be produced when making claims against this guarantee 5 Any tampering or alteration made to the warranty card or to the serial number on the unit will invalidate the warranty 6 The dealer or the agent shall notify the customer when the repairs have been completed The customer must claim the goods within fourteen 14 days from the date of notice failing which the Company reserves the right to impose storage charges 7 he Company reserves the right to dispose of the unit after 90 days from the date of notice In a manner that it sees fit and without compensation to the customer
4. high fidelity engineering ee Installation 4 Operation The Exposure 3010S2 Integrated Amplifier Front View a Turn amplifier volume control to minimum CeO pane TL amp exposune b Press power switch The LED power indicator will light up The amplifier output relay will activate after a 6 second delay a Set the volume control to minimum before connecting or disconnecting any cable b Connect the mains cable to the IEC mains input socket c Connect to the mains outlet on the wall DO NOT switch on until all input and output connections are made c Without playing any CD Player Tuner Tape Disc Recorder Turnable Video Player turn the volume control knob slowly clockwise to around 30 You should only hear a faint hiss 2 Source Component Connections The Exposure 3010S2 Integrated Amplifier Back View 4 Thi die sours Salsailan lnslotosstoc alive source component CD Player Tuner Tape Disc Recorder Turnable Video Player Quick Start Thank you for purchasing the Exposure 3010S2 Integrated Amplifier Oaoaoooeaa ca o e Audio should now be heard when the source component is played ole rere ee Oc SEa 5 Remote Control The Exposure 3010S2 Integrated Amplifier is fitted with six 6 line level RCA D Phono inputs suitable for connection to CD players tuners and tape or Outputs disc recorders Before you start The source selection
5. input gain 8dB full volume Aa LON ya se oade Pre amplifier Output Frequency Response Total Harmonic Distortion lt Q 03 at rated output ref KHz gt QOcdB ref rated output gt 60dB 20Hz 20KHZz 1O 120V or 220 240V 50 60HZz factory set lt 400VA 8 Ohms load both channels driven Signal to Noise Ratio Channel Separation Mains Supply Power Consumption Dimensions H x W x D Nett Weight Unpacked 2 kg Gross Weight Packed 14 kg 115 mm x 440 mm x 300 mm Exposure Warranty Policy The Exposure warranty entitles you to FREE repair of this unit for the first three 3 years from the date of purchase 2 This warranty is valid only if the unit is purchased from an authorised Exposure dealer registered with the authorised agent in your country of residence and issued with a recognised warranty card 3 The agent accepts no responsibility for defects arising from accident misuse abuse wear and tear neglect or through unauthorised adjustment and or repair or replacement of any components nor will they accept responsibility for damage or loss occurring during transit to or from the person making a claim under warranty 4 The Exposure warranty covers Parts and labour costs for three 3 years from the date of purchase Please retain your original receipt as proof of purchase and purchase date The guarantee is extended only to the original purchaser and Is not transferable When making cl
6. lf 2 Remove the mains cable from the wall and the IEC socket 6 Observe the position of the plug on the phono card and carefully plug it in ensuring that all of the pins are inserted correctly into their connectors 5 Remove the small jumper board that is fitted on the right hand side at the back EN i GITET Wea 411 ARS A he Be o oy UTNE S i hi gt l 7 Fit the three M3 bolts that are supplied with the phono card _ 4 Slide the cover back about 2cm until it is free to move upwards to reveal the main circuit board 8 Replace the cover and screws Safety Incorrect installation or inappropriate use of the Exposure 3010S2 Integrated Amplifier may result in injury due to electrical shock e Ensure that the voltage rating on the rear panel of this unit matches that of your local mains supply e Ensure that the mains cable and plug supplied with this unit are also correct Contact your dealer immediately if this is not the case e This unit is protected by a mains fuse which is accessible as part of the IEC socket on the rear panel e Fuse replacement specifications 220 240V units 10 120V units T4A fuse T 8A fuse e Protect the unit against all forms of liquid Never expose unit to dripping or splashing or place objects filled with water such as vases on the unit e Unplug unit from mains when not in use for prolonged periods e Do not open this unit there
7. ntegrated Amplifier rom rs a Pest gi so ah _ P O a o CD Player Tape Deck i ee eo l OE JEEE a Connect left and right loudspeakers to corresponding left and right speaker outputs on amplifier o 50000 j F a b Connect terminal of loudspeaker to terminal of the amplifier Tuner Satellite c Connect terminal of loudspeaker to terminal of the amplifier Cable TV eu i EEEE i Bi wired Connection Bi wiring may provide a useful gain in subjective performance Should you choose this option please refer to the Extended Set Up instructions overleaf DVD U Bi amping of Loudspeakers IQGCO i i i Ki Player Bi amping of loudspeakers using a 3010S2 Integrated and a 3010S2 Power Am plifier provides a useful gain in subjective performance For this operation please Turntable connection requires the installation i e l refer to the Extended Set Up instructions overleaf of an optional MM or Mc Phono Card 9 10 oer AUTE ALMUPH TUNER CO Vol4 AUS AUS TAPE VOL PRGA RANDOM TIME APT PREY NEXT lt SEARCH PLAY STOP PAUSE OFEN Red Button Mutes the volume output to minimum Indicator lights on VOLUME and INPUT SELECTOR knobs will be turned off Press the red button again or press the VOL button to return volume to its previous level and restore indicator lights Green Buttons Increase decrease the volume Indicator light on VOLUME knob will flash as vol
8. or connecting a pair of loudspeakers in bi wiring mode Bi amping of Loudspeakers Bi amping of suitable loudspeakers using a 30 10S2 Integrated Amplifier and a 301052 Power Amplifier provides a useful gain in subjective performance The Integrated Amplifier is used to drive the treble units and the Power Amplifier is used to drive the bass units through the loudspeaker s split crossover with the joining links removed Check your loudspeaker user manual for the wiring connections 2 Follow the diagram on the right for connecting a pair of loudspeakers in bi amping mode Installation of aMC or MM Phono Module Right Speaker High Frequency High Frequency Preout ee ee ee Rear of Exposure 3010S2 Integrated Amplifier 0 0 F T q Left Speaker Right Left SPK SPK2 SPK SPK2 High Frequency Low Frequency L ee Connecting a pair of loudspeakers in bi wiring mode Right Speaker Left Speaker Rear of Exposure 301 0S2 Integrated Amplifier Preout Right Left SPKI SPK2 SPKI SPK2 0000 o a 0 INPUT Rear of Exposure 3010S2 Power Amplifier SPK SPK2 SPKI SPK2 High Frequency L a Right Left id Low Frequency Connecting a pair of loudspeakers in bi wiring mode This is best carried out by your dealer However if you wish to attempt installation yourse
9. ume is adjusted Black Buttons Select input sources Indicator light on the INPUT SELECTOR knob will flash as sources are selected Installation of aMC or MM Phono Module For details please refer to the Extended Set Up section overleaf or contact your dealer Exposure 3010S2 Integrated Amplifier Extended Set Up Although the Exposure 301QS2 Integrated Amplifier is able to drive almost any loudspeaker system the best results will most likely be achieved with speakers rated at 8ohms While the Exposure 3010S2 Integrated Amplifier is compatible with most types of loudspeaker cables the type of cables used can influence the subjective performance of your system Please ask your Exposure dealer for advice on bi amping loudspeaker cable compatibility and how to get the best from your Exposure 3010S2 Integrated Amplifier Note The Exposure 3010S2 Integrated Amplifier is internally protected against damage from short circuits However no such protection is infallible and damage may occur If positive and negative speaker cables are inadvertently connected together Bi wiring The Exposure 301052 Integrated Amplifier is fitted with two sets of 4mm loudspeaker sockets for bi wired connections Another pair of speaker wires Is required for this operation Ensure that the links at the speaker terminals between the high frequency and the low frequency are removed on both loudspeakers 2 Follow the diagram on the right f
Download Pdf Manuals
Related Search
Related Contents
GT 5 - euro HÜBNER Fig. 1 Fig. 2 Fig. 3 Fig. 4 R-Flex Knee CPM Owner`s Manual Copyright © All rights reserved.
Failed to retrieve file