Gefen GTB-HDBT-POL
Contents
1. 2 Connect an IR emitter from the IR Out jack on the Sender unit to the IR sensor window of the source device to be controlled CONNECTING AND OPERATING THE EXTENDER FOR HDMI W POL control the source from the display location point the included IR remote control at the IR Extender connected to the Receiver unit The IR signals are transmitted from the Receiver to the Sender unit over the CAT 5e CAT 6 cable HDMI Cable Receiver Unit IR Extender HDTV Display Source Remote CAT 5e Cat 6 Receiver Unit Sender Unit IR Emitter Source 10 CONNECTING AND OPERATING THE EXTENDER FOR HDMI W POL How to Connect the Bi Directional IR Bi Directional IR Controlling the Display In the example below we will be setting up IR control for the display from the source location The following illustrations assume all A V devices have already been connected See page 8 for details 1 For IR control of a display from the source location connect 3 5mm to 3 5mm mono or stereo cable from one of the IR Emitter jacks on an automation device such as the Gefen PACS or Mini PACS to the IR In jack on the Sender unit Sender Unit 2 Connect an IR emitter from the IR Out jack on the Receiver unit to the IR sensor window of the HDTV display to be controlled 11 CONNECTING AND OPERATING THE EXTENDER FOR HDMI W POL 3 Tocontrol the display from the source location point the i2. D s both the Sender and Receiver units will turn on indicating that both units are powered IF HDCP is present the LED will be lit in solid blue IF HDCP is not detected the LED s will flash blue amber Wiring Diagram for the Extender for HDMI w POL CAT 5e CABLE ERN Gefen Up To 175 FT TOOLBHX HDMI CABLE ME IR Hi Def Source EXT PACS IR Input IR Extender IR Emitter ee Receiver IR Emitter Sender 7 HD Display GTB HDBT POL CONNECTING AND OPERATING THE EXTENDER FOR HDMI W POL How to Connect the Bi Directional IR Bi Directional IR The Bi Directional IR feature allows two simultaneous methods of control Control of the source device and control of the display The source device can be controlled from the viewing location by connecting an IR Extender Gefen part no EXT RMT EXTIRC to the Receiver unit The display can be controlled from the source location by connecting a PACS Mini PACS to the Sender unit Controlling the Source In the example below we will be setting up IR control for the source from the display location The following illustrations assume all A V devices have already been connected See page 8 for details 1 For IR control of a source connect the IR extender to the IR Ext jack on the Receiver unit A CAT 5e CAT 6 cable should already be connected from the Link jack on the Receiver to the Link jack on the Sender unit 2 am
3. Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Pr
4. Gefen TOOLBOX Extender for HDMI w POL GTB HDBT POL GTB HDBT POL BLK User Manual efen T iBHX T LBHX is is Extender for i Extencder for i HDMI w POL HDMI w POL amp Extender for j Extender for HDMI w POL S HDMI w POL gefentoolbox com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday Pacific Time Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefentoolbox com support gefentoolbox com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice Extender for HDMI w POL is a trademark of Gefen LLC HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing in the United States and other countries 2012 Gefen LLC All rights reserved Alltrademarks are the property of their respective owners Rev A1 CONTENTS Introduction Operation Notes Features Sender Unit Layout sender Unit Descriptions Receiver Unit Layout Receiver Unit Descriptions Connecting the Extender for HDMI w POL Wiring Diagram Bi Directional IR Controlling the Source Bi Directional IR Controlling the Display Network Cable Wiring Diagram Wall Mount
5. able M M 1 Single Infrared Emitter 1 IR Extender with Carrier Frequency 1 24V DC Locking Power Supply 1 Set of Mounting Plates Attached 1 Quick Start Guide SENDER UNIT LAYOUT Front SENDER UNIT DESCRIPTIONS IR Out Connect the included single infrared IR emitter Gefen part no GTB IREMIT from this jack to the IR sesnor window of the source Link Connect a CAT 5e CAT 6 cable from the Sender to the Receiver unit 24V DC Connect the included 24V DC power supply to this connector and plug the AC power cord into an available electrical outlet Only use the power supply shipped with this unit Power HDCP Indicator This LED will turn on once the included 24V DC power supply has been connected If HDCP is present the LED will be lit in solid blue If HDCP is not detected the LED will flash blue amber HDMI Locking Connector Used to lock the HDMI cable in place HDMI Input Connect a Hi Def source to this port using the included locking HDMI cable Please see the Features section on page 3 for supported HDMI features IR In Connect a 3 5mm to 3 5mm mini mono cable from this jack to one of the IR Emitter jacks on the Gefen PACS or Gefen Mini PACS IR Emitters or IR Extenders will not function if connected to this port RECEIVER UNIT LAYOUT Front Back RECEIVER UNIT DESCRIPTIONS IR Out Connect a single infrared IR emitter Gefen part no G TB IREMIT from this jack to the IR sensor window o
6. drywall surface use a 6 drywall screw When installing it is recommended to use the center hole on a stud 14 SPECIFICATIONS Maximum 1 RO AA 225 MHz Video Input Connector Sender 1 HDMI Type A 19 pin female locking Video Output Connector Receiver 1 HDMI Type A 19 pin female locking Link Connectors Sender 1 RJ 45 shielded Power HDGP Indicator LED een nee Bi color Blue Amber IR Extender Port 3 5mm mini stereo jack IR Out Port Sender 3 5mm mini mono jack IR In port SENO Een een 3 5mm mini mono jack Pow r SUpply NO CE 1 24V DC locking POW en ne ee 24W per unit max Operating Temperature 32 to 104 F 0 to 40 C Dimensions W x H x D 4 3 x 1 x 3 2 86mm x 33mm x 83mm SINBDIBO WEN une rer 4 bs 1 8 kg 15 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications
7. eters Shielded STP CAT 5 or CAT 6 is recommended However unshielded UTP CAT 5 or CAT 6 is acceptable depending on cable quality but is not the top choice Care should always be given to keep these cables away from power lines and other electromagnetic interference sources e NOTE Shielded cable has an advantage by providing immunity to Electromagnetic Interference EMI from cell phones and A C motors POL Power Over Line technology from Gefen sends power to the Receiver uni over the same CAT 5e 6 cable that is used for extending the HDMI signal HDBaseT technology allows HDMI IR Bi directional and power to be sent on one CAT 5e 6 cable FEATURES HDMI Features Supported e Resolutions up to 1080p Full HD e 12 bit Deep Color e 7 1 audio Dolby TrueHD Dolby Digital Plus and DIS HD Master Audio e pass through e pass through e Sync pass through Features e Extends HDMI and 3DTV up to 230 feet 70 meters over a single CAT 6 or up to 198ft 60 meters over a single CAT 5e Bi Directional IR remote control of source device and the display e Gefen POL feature provides power to the Receiver unit over the CAT 6 e Uses HDBasel6 technology e Locking power connector e Easy surface mounting e Available in Black and White finishes Package Includes 1 Extender for HDMI w POL Sender unit 1 Extender for HDMI w POL Receiver unit 1 6 ft Locking HDMI c
8. f the HDTV display Link Connect a CAT 5e CAT 6 cable from the Sender to the Receiver unit Power HDCP Indicatior This LED will turn on once the included 24V DC power supply has been connected If HDCP is present the LED will be lit in solid blue If HDCP is not detected the LED will flash blue amber HDMI Locking Connector Used to lock the HDMI cable in place HDMI Output Connect an HDTV display to this port using a locking HDMI cable IR EXT Connect the included IR extender Gefen part no EXT RMT EXTIRC to this jack CONNECTING THE EXTENDER FOR HDMI W POL How to Connect the Extender for HDMI w POL Using the included locking HDMI cable connect a Hi Def source to the HDMI Input port on the Sender unit Connect an HDTV display to the HDMI Output port on the Receiver unit using another HDMI cable Connect a CAT 6 cable from the Link jack on the Sender unit to the Link jack on the Receiver unit up to 230 feet 70 meters A CAT 5e cable can be used to extend up to 198 feet 70 meters the TIA EIA568B specification see page 9 NOTE If terminating network cables in the field please adhere to IR Control For details on using the Bi directional IR feature see page 9 Connect the included 24V DC power supply to the Sender unit and plug the AC power cord into an available electrical outlet Power to the Receiver unit is delivered from the Sender unit over the CAT 5e CAT 6 cable using Gefen POL technology The LE
9. ing Instructions Specifications Warranty INTRODUCTION Congratulations on your purchase of the Extender for HDMI w POL Your complete satisfaction is very important to us About Gefen We specialize in total integration for your home theater while also focusing on going above and beyond customer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line Please visit http www gefen com for the latest offerings in High Definition signal solutions or call us between the hours of 8 00 am and 5 00 pm Monday Friday Pacific Standard Time for assistance with your A V needs We ll be happy to assist you The GefenToolBox Extender for HDMI w POL The GefenToolBox Extender for HDMI with POL extends HDMI up to 230 feet 70 meters using one CAT 6 cable or up to 198ft 60m using one CAT 5e Resolutions up to 1080p Full HD with multichannel digital audio are supported This product provides Bi Directional IR extension between the Sender and the Receiver unit allowing the transfer of IR commands from one remote location to the other Bi Directional IR can be used to control A V sources placed near the sender unit and to send IR automation commands to devices placed near the Receiver unit Gefen POL Power Over Line technology powers the Receiver unit using the same 5 or CAT 6 cable that extends the HDMI signal from the Sender unit This feature eliminates the need for an external power su
10. ncluded IR remote control at the PACS or PACS connected to the Sender unit The IR signals are transmitted from the Sender to the Receiver unit over the CAT 5e CAT 6a cable Refer to the PACS or Mini PACS User Manual for more information on using IR commands EXT PACS Source HDMI Cable 3 5mm cable Sender Unit CAT 5e CAT 6 SSS St til Sender Unit gt Receiver Unit IR Emitter HDTV Display 12 NETWORK CABLE WIRING DIAGRAM Gefen recommends the TIA EIA 568 B wiring option Please adhere to the table below when field terminating cable for use with Gefen products 12345678 Blue White CAT 5 CAT 5e and CAT 6 cabling comes in stranded and solid core types Gefen recommends using solid core cabling CAT 6a cable is also recommended It is recommended to use one continuous run from one end to the other In some cases connecting through a patch might not work 13 WALL MOUNTING INSTRUCTIONS QU 6 D d E ps Lf li 22 MMi 97 Sy The Gefen Toolbox Extender for HDMI w POL should be mounted vertically on a wall or inside outside a cabinet with wood drywall screws as shown in the diagram above There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the HDMI cable For installation on a
11. oduct page under the Support section of the Gefen Web site 16 Rev A1 MA GTB HDBT POL 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefentv com support gefentv com Qu E cc o This product uses UL or CE listed power supplies
12. pply at the Receiver unit which helps simplify installation How It Works Connect the Sender unit to the Hi Def source using an HDMI cable Use another HDMI cable to connect the Receiver unit to the HDTV display Connect a single CAT 6 cable up to 230 feet 70 meters or CAT 5e cable up to 198ft 60m between the Sender and Receiver units Connect the included 24V DC power supply to the Sender unit and plug the power supply in to an available electrical outlet Power to the Receiver unit is delivered from the Sender unit over the CAT 5e 6 cable using Gefen POL technology To control the Hi Def source from the display location connect the IR Extender Gefen part no EXT RMT EXTIRC to the Ext IR connector on the Receiver unit Connect the IR emitter Gefen part no GTB IREMIT to the IR Out of the Sender unit and place the IR emitter over the IR sensor of the Hi Def source Point the IR remote at the IR Extender to control the Hi Def source For IR control of a device placed near the Receiver unit such as the display connect the IR output from an automation device such as the Gefen PACS or Mini PACS to the IR In connector on the Sender unit Connect the IR emitter Gefen part no GTB IREMIT to the IR Out on the Receiver unit and attach the IR emitter to the IR sensor of the display 1 OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE EXTENDER FOR HDMI W POL CAT 5e or CAT 6 cables should not exceed 230 feet 70 m
Download Pdf Manuals
Related Search