Amer Networks SS3GR1028F network switch
Contents
1. SFP LX L transceiver 1000Base LX SFP 1310nm SMF 10km or MMF 550m SFP LX 20 L transcever 1310nm lightwave 9 125um_ single mode fiber 20km SFP LX 40 transceiver 9 125um single mode fiber 40km SFP LH 70 L transceiver 9 125um single mode fiber 70km SFP LH 120 L transceiver 9 125um single mode fiber 120km SFP GT Module 1000Base T SFP interface card module RJ 45 interface 1 7 SS3GR1028F Series Installation Guide Chapter 1 Introduction 1 4 6 SS3GR10XFP SS3GR10SFP Description Extended Module Provides 2 slots to install 2 SS3GR10XFP SS3GR10SFP or SS3GR10SFP extended modules Extended module model SS3GR1028F series switch Extended module description SS3GR10XFP Support 10G module XFP interface SS3GR10SFP Support 10G module SFP interface SS3GR10SFP Support 1G module SFP interface Take SS3GR10XFP as a example extended module diagram is shown as follows Figure 1 4 SS3GR10XFP structure diagram Each extended module s panel diagram is shown as follows Figure 1 6 panel diagram of SS3GR10SFP 1 8 SS3GR1028F Series Installation Guide Chapter 1 Introduction Figure 1 7 panel diagram of SS3GR10SFP Extended modules LED descriptions are in the following Table 1 7 LED descriptions of 10Gb extended module Status Description Ports are at link state with 10G Link Activity Blink Green Ports are at active state with 10G No link or the link is fai2. arcing Power line breakage Imperfect earth Overload circuit and Electrical short circuit If electric shock fire electrical short circuit occurs please cut off the electricity supply and alarm rapidly Rescue the injured person in the contingency under inherently safe give the injured person proper first aid treatment according to the injury state and seek help from the Medical Emergency using various ways 2 2 Installation Preparation 2 2 1 Verify the Package Contents Please unpack the shipping package and verify carefully the contents inside 2 2 2 Required Tools and Utilities The required tools and utilities are shown below WH Cross screwdrivers H Flat blade screwdriver WH ESD wrist strap H Antistatic uniform Caution Users should prepare the required tools by themselves 2 3 Installation Guide 2 3 1 Installing Switch 2 5 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation Fig 2 1 Install sketch map on the rack Please mount The SS3GR1028F on the 19 rack as below 1 Attach the 2 brackets on the SS3GR1028F with screws provided in the accessory kit 2 Put the bracket mounted switch smoothly into a standard 19 rack Fasten the SS3GR1028F to the rack with the screws provided Leave enough space around the switch for good air circulation Caution The brackets are used to fix the switch on the rack They can t serve as a bearing Please place a
3. hot swappable SS3GR10SFP extended module can insert SFP 1Gb fiber transceiver 2 3 6 SS3GR10SFP Extended module Installation The SS3GR1028F series provide 10Gb slots The procedure for installing the SS3GR10SFP module and the SFP 1Gb fiber transceiver is shown below Step 1 Put on an ESD wrist strap or antistatic gloves Step 2 Insert the SS3GR10SFP module to the guide rail inside the 10Gb module slot Step 3 Push the SS3GR10SFP module along the guide rail gently until it comes into contact with the machine panel Step 4 Insert the SFP transceiver to the guide rail inside the SS3GR10SFP Do not put the SFP transceiver up side down Step 5 Push the SFP transceiver along the guide rail gently until it comes into contact with the SS3GR10SFP Note the SFP 1Gb fiber transceiver is hot swappable Caution Do not stare directly at the 2 fiber bores in the fiber transceiver when the switch is in operation otherwise the laser may hurt your eyes 2 3 7 Copper Cable Fiber Cable Connection Copper cables should be connected as below 2 8 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation Step 1 Insert one end of the Ethernet cable to the RJ 45 Ethernet port in the copper cable line card of the switch Step 2 Insert the other end of the Ethernet cable to the RJ 45 Ethernet port of other device Step 3 Check all status indicators for the corresponding ports a lighted LED indicates that the link has been es
4. input specification for the detailed information AC Power supply connection procedure is described as below 1 Insert one end of the power cable provided in the accessory kit into the power source 2 9 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation socket with overload and leakage protection and the other end to the power socket in the back panel of the switch 2 Check the power status indicator in the front panel of the switch The corresponding power indicator should light The SS3GR1028F series is self adjustable for the input voltage As soon as the input voltage is in the range printed on the switch surface the switch can operate correctly 3 When the switch is powered on it executes self test procedure and startups Caution The input voltage must be within the required range otherwise the switch can be damaged or malfunction Do not open the switch shell without permission It can cause physical injury 2 3 9 DC Power Supply Connection The SS3GR1028F series supports 220V AC input 48V DC input or 220V AC 48V DC input simultaneously 48V DC input connection procedure is described as below 1 Insert DC power linker provided in the accessory kit into DC power source socket in the back panel of the switch 2 Check whether the power status indicator is light in the front panel of the switch 3 When the switch is powered on it executes self test procedure and startups Caution The input
5. In band and Out of band Management CLI and WEB interface and RMON It can mail the correlative sensitive information to the administrator abide by SMTP protocol Support SSH protocol ensure the configuration management security of the switch 1 3 Physical Specifications Item SS3GR1028F Dimension 440 X 324 A4 W H D Cmm Weight lt 6kg Fixed ports 12 SFP fiber ports 12 1000Mb Combo ports 2 interfaces with extended card 1 2 SS3GR1028F Series Installation Guide Chapter 1 Introduction Management 1 Console port ports System Supports AC DC power input power AC input The rating voltage range 100V 240V AC 50 60HZ The max voltage range 90V 264V AC 47HZ 63HZ DC input 48V DC input 48V 60V DC 2 5A Output Do not support power supply of PoE The max 35W Power Consumption Fan Support automatic timing Operating 0 C 50 C Temperature Relative 10 90 Humidity Table 1 1 Physical Specifications 1 4 Description of Hardware 1 4 1 Front Panel SS3GR1028F Ethernet switch provides 12 1000Mb fiber ports 12 1000Mb Combo ports 8 function LEDs and 1 Console port Fig 1 1 Front Panel of SS3GR1028F 1 3 SS3GR1028F Series Installation Guide Chapter 1 Introduction 1 4 2 Back Panel SS3GR1028F supplies 2 interfaces with the extended card 1 interface with 48V DC power input and 1 interface with 220
6. SS3GR1028F Series Installation Guide Content Content CHAPTER 1 INTRODUCTION ccccceeeeeeeeeesseeeseeeeeeeeeeseens 1 1 Pe OVERVIEW EE 1 1 1 2 INTRODUCTION TO PRODUCT iis cecncvencviscvenccascvascvisivusdviscvascvissviscuincdencwases 1 1 1 2 1 PFOGUCT Ove EW eet cave cles co tate Sedan ee dee Eege 1 1 1 2 2 Features and Benefits ecccceeceeeeeeeeeeeeeeeeeeeeeeaneeeeeeseaseeeesneneeeees 1 1 1 3 PHYSICAL SPECIFICATIONS se uisissiesdcauscendetussevdvavenauduausueudsdvsunnduaneasuduazans 1 2 1 4 DESCRIPTION OF HARDWARE 0 scccesseccesseccnsseccenseccnsseccnssesenssesenseess 1 3 14 A Front Panel eebe egene SCENE 1 3 1 4 2 Back Pane liciice ctesccsectecscat eg egche dadaa aae areenaa eaaa enaa aana r aa Aaaa iaaiiai 1 4 1 4 3 DC Power PoE Power INputt s sssunssssnunnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn 1 4 1 4 4 Status LEDS wi is ccccecescee cece nccevesteneeiceneceevesseceeteecceeceseecteausesteeuevedenuadee ccecee 1 4 1 4 5 Interface Description of Front Panel ccccsseeeeesseeneeeesesneeeeneeeeees 1 7 1 4 6 SS3GR10XFP SS3GR10SFP Extended Module Description 1 8 CHAPTER 2 HARDWARE INSTALLATION cccsseeeeeeeees 2 1 2 1 INSTALLATION NOTICE wincstnctacssdcetancnagnsincntaetionnicucioinisutinsnndwttssabsuaiedakane 2 1 2 1 1 Environmental Requirements cccsseeceesseeeeesseeneeeeseeneneeenseeeeeneees 2 1 2 1 2 Installati n Notice voc seiss wees teneecedeceewec
7. System is loading On Green System is operating normally On Green System is malfunctioning ALM e Off System is operating normally SR On Green System is using DC power Off System does not use DC power On Green Port of M1 is at link state On Green Port1 of M1 is receiving or sending M1 1 Blink ink the data Off Port1 of M1 is not at link state M1 2 On Green Port2 of M1 is at link state On Green Port2 of M1 is receiving or sending Blink the data Off Port2 of M1 is not at link state 1 6 SS3GR1028F Series Installation Guide Chapter 1 Introduction On Orange Port2 of M1 is not at link state but M1 is in place On Green Port1 of M2 is at link state On Green Port1 of M2 is receiving or sending M2 1 Blink ink the data Off Port1 of M2 is not at link state On Green Port2 of M2 is at link state On Green Port2 of M2 is receiving or sending Blink the data M2 2 Off Port2 of M2 is not at link state On Orange Port2 of M2 is not at link state but M2 is in place 1 4 5 Interface Description of Front Panel Provides RJ 45 1000Mb copper port and the interface of SFP 1000Mb fiber transceivers SFP GT Table 1 6 interface descriptions Interface mode Spec RJ 45 port 10 100 1000Mbps auto negotiation MDI MDI X cable mode auto negotiation 5 kinds of UTP 100 m SFP SX L transceiver 1000Base SX SFP 850nm MMF 550m
8. V AC power input Fig 1 2 Back Panel of SS3GR1028F 1 4 3 DC Power PoE Power Input Supports AC DC input power backup and PoE power output pin outs signal of DC power and PoE power are distributed as below Pinl Pin2 Dn DC socket AC socket Fig 1 3 Pin outs Distribution of DC Input SS3GR1028F There are 3 pin outs for DC socket PIN1 GND Ground connection PIN2 48V DC power cathode input PIN3 OV DC power positive electrode input 1 4 4 Status LEDs Mainboard LEDs include two parts one is 24 48 1000M interface LEDs they show each port state at RJ45 plug in each port corresponds a LED with double colors 1 4 SS3GR1028F Series Installation Guide Table 1 2 Port LEDs LED Status Description On On means ports are in the link state of 100M or export PoE power Off Off means ports are not in the link Red state of 100M or do not export PoE power Blink Send or receive the data On On means ports are in the link state of 1000M Green Off Off means ports are not in the link state of 1000M Blink Send or receive the data The other is system LEDs they are used to show the work status of the system at the right of front panel ne Status Description Symbol P PWR On Green Power is operating normally Off Power is abnormally DIAG On Green blink System is loading On Green System is operating normally On Green System
9. eesecanden cee ndeseed anadenia aani 2 4 EARKEZGIIOVAUC Tue ET 2 4 2 2 INSTALLATION PREPARATION cccesssseeecccessseeeceensseeeseensseeeeeeenseesseeensees 2 5 2 2 1 Verify the Package Contents csssccesseeeeeeseeeeeenseeneeeeseeneeeeenseeneeeneees 2 5 2 2 2 Required Tools and Utilities ccccceseeeeeeseeeeeeeseeeeeeeseeeeeesnseeeeeneees 2 5 2 3 INSTALLATION GUIDE ee gugesee eege eekOgee ege ue 2 5 ERIC Ee TEE 2 5 2 3 2 CONNECTING CONSOLE ccccesceneeeeeeeeeeeeseeeeeeeseeeeeeaseeneeeaseesneeseneseeeaeneees 2 6 2 3 3 SFP Transceiver Installation cccccseseeseeeeceeeeeeeeeeeeneeceeeeeeeeneeeseens 2 7 2 3 4 SS3GR10XFP Extended Module Installation cccesseeceseeeeeeeeees 2 7 2 3 5 SS3GR10SFP Extended module Installation cccsseeeesseeeneeeees 2 8 2 3 6 SS3GR10SFP Extended module Installation cccesseeesseeeeeeeees 2 8 2 3 7 Copper Cable Fiber Cable Connection 2 ccccceseessseeceeeeeeeeeeeenees 2 8 2 3 8 AC Power Supply Connection cccsseeeeeesseeeeesseeeeeeeseeneneeenseeneneneees 2 9 2 3 9 DC Power Supply Connection ccccceceeeeeeeseeeeeeeseeeeeeeeeeneneeenseeeeens 2 10 2 3 10 PoE Power Supply Connection ccccsceeecccesseeeeeeseeeeeeeeseneneeenseeenens 2 10 SS3GR1028F Series Installation Guide Chapter 1 Introduction Chapter 1 Introduction 1 1 Overview The SS3GR1028F series switch are intelligent network management switch used by the n
10. ered within 5 hours 2 1 1 3 Power Supply Before powering on the power supply please check the power input to ensure proper grounding of the power supply system The input source for the switch should be reliable and secure a voltage adaptor can be used if necessary The building s circuit protection system should include in the circuit a fuse or circuit breaker of no greater than 240 V 10 A It is recommended to use a UPS for more reliable power supplying Caution Improper power supply system grounding extreme fluctuation of the input power and transients or spikes can result in larger error rate or even hardware damage 2 1 1 4 Preventing Electrostatic Discharge Damage Static electric discharges can cause damage to internal circuits even the entire switch Follow these guidelines for avoiding ESD damage m Ensure proper earth grounding of the device H Perform regular cleaning to reduce dust RH Maintain proper temperature and humidity m Always wear an ESD wrist strap and antistatic uniform when in contact with circuit boards 2 1 1 5 Anti interference All sources of interference whether from the device system itself or the outside environment will affect operations in various ways such as capacitive coupling inductive coupling electromagnetic radiation common impedance including the grounding system and cables lines power cables signal lines and output lines The following should be noted m Precautions sh
11. etwork environment which needs the high performance the bigger port density and the convenient installation 12 fiber ports 12 Combo ports 2 extended cards DC power 1 2 Introduction to Product 1 2 1 Product Overview Front panel of SS3GR1028F supplies 12 1000M fiber ports and 12 Combo ports Features and Benefits Various Interfaces Provides 12 1000Mb fiber ports 12 1000Mb Combo ports 1000Mb fiber SFP ports 1000Mb copper ports and 2 slots with the extended cards lt Secure Power Supply Provides DC AC power backup support 220V AC input 48V DC input or 220V AC 48V DC input simultaneously lt Support 10Gb Ethernet 10Gb Ethernet which adopts full duplex technology instead of low speed half duplex CSMA CD protocol is a big leap in the evolution of Ethernet 10Gb Ethernet can be deployed in star or ring topologies Provide broad bandwidth and powerful processing capacity It is suitable for metropolitan networks and wide area networks Users can simplify network structures and reduce cost of network construction lt Networking Protocols Supports 802 1d w s 802 1Q 802 1p 802 3ad 802 3x GVRP DHCP and SNTP etc The switches also support the multicast protocols such as IGMP DVMRP and PIM Moreover this switch series supports RIPv1 2 OSPF BGP and IPv6 protocols All these protocols supported enable this switch series to meet the requirements of complex network constructions ACL Support comprehensi
12. he installation users must use the brackets and screws provided in the accessory kit Users should use the proper tools to perform the installation Users should always wear antistatic uniform and ESD wrist straps Users should use standard cables and connecters After the installation users should clean the site Before powering on the switch users should ensure the switch is well grounded Users should maintain the switch regularly to extend the lifespan of the switch 2 1 3 Security Warnings When using SFP transceiver do not stare directly at the fiber bore when the switch is in operation Otherwise the laser may hurt your eyes Do not attempt to conduct the operations which can damage the switch or which can cause physical injury Do not install move or disclose the switch and its modules when the switch is in operation Do not open the switch shell Do not drop metals into the switch It can cause short circuit Do not touch the power plug and power socket Do not place the tinder near the switch Do not configure the switch alone in a dangerous situation Use standard power sockets which have overload and leakage protection Inspect and maintain the site and the switch regularly Have the emergence power switch on the site In case of emergence switch off the 2 4 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation power immediately Caution Potential risk include Electric leakage Power supply
13. ide 10Gb slots The procedure for installing the SS3GR10XFP module and the XFP 10Gb fiber transceiver is shown below Step 1 Put on an ESD wrist strap or antistatic gloves Step 2 Insert the SS3GR10XFP module to the guide rail inside the 10Gb module slot Step 3 Push the SS3GR10XFP module along the guide rail gently until it comes into contact with the machine panel Step 4 Insert the XFP transceiver to the guide rail inside the SS3GR10XFP Do not put the XFP transceiver up side down Step 5 Push the XFP transceiver along the guide rail gently until it comes into contact with the SS3GR10XFP Note the XFP 10Gb fiber transceiver is hot swappable 2 7 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation 2 3 5 SS3GR10SFP extended module Installation The SS3GR1028F series provide 10Gb slots The procedure for installing the SS3GR10SFP module and the SFP 10Gb fiber transceiver is shown below Step 1 Put on an ESD wrist strap or antistatic gloves Step 2 Insert the SS3GR10SFP module to the guide rail inside the 10Gb module slot Step 3 Push the SS3GR10SFP module along the guide rail gently until it comes into contact with the machine panel Step 4 Insert the SFP transceiver to the guide rail inside the SS3GR10SFP Do not put the XFP transceiver up side down Step 5 Push the SFP transceiver along the guide rail gently until it comes into contact with the SS3GR10SFP Note the SFP 10Gb fiber transceiver is
14. is malfunctioning ALM l Off System is operating normally SES On Green System is using DC power Off System does not use DC power On Green M1 is in place M1 Off M1 is not in place On Green M2 is in place M2 Off M2 is not in place Chapter 1 Introduction LEDs of SS3GR1028F show the corresponding state There are two kinds of LEDs on front panel one of its kinds is fiber copper LEDs of port transceiver they are at RJ45 linker or SFP linker Each port of RJ45 linker corresponds a LED with double colors each port of SFP linker corresponds two LEDs detailed descriptions are shown in the following tables 1 5 SS3GR1028F Series Installation Guide Chapter 1 Introduction Table 1 3 RJ45 Port LEDs LED Status Description On It means port is at link state Green Off It means port is not at link state Blink Send or receive the data Table 1 4 SFP Port LEDs LED Status Description On SFP port is at link state SEN Off SFP port is not at link state Blink There is no this state On There is no this state Right LED Off No data is received or sent Blink Send or receive the data System LEDs of SS3GR1028F are at the right of the front panel Table 1 5 SS3GR1028F System LEDs Panel Si Status Description Symbol On Green Power is operating normall PWR p g y Off Power is abnormally DIAG On Green blink
15. lure Table 1 8 XFP SFP transceivers descriptions XFP SR transceiver 10GBase SR XFP multi mode fiber transceiver 850nm 62 5 u m MMF 32m 50 u m 500MHz km MMF 85m 502m 2000MHz km MMF 300m XFP LR transceiver 10GBase LR XFP single mode fiber transceiver 1310nm SMF 10km XFP ER transceiver 1550nm SMF 40km XFP ER 70 transceiver 1550nm SMF 70km SFP LR transceiver 10GBase LR SFP 1310nm SMF 10km SFP SR transceiver 10GBase SR SFP 850nm 62 5um MMF 32m 50um 500MHz km MMF 85m 50um 2000MHz km MMF 300m 1 9 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2 1 Installation Notice To ensure the proper operation and your physical security carefully the following installation guide 2 1 1 Environmental Requirements m The switch must be installed in a clean area Otherwise the switch may be damaged by electrostatic adherence HR Maintain the temperature within O to 50 C and the humidity within 10 to 95 non condensing m The switch must be put in a dry and cool place Leave sufficient spacing around the switch for good air circulation m The switch must work in the right range of power input AC power 90 264V 50HZz DC power 40 60V m The switch must be well grounded in order to avoid ESD damage and physical injury of people m The switch should avoid the sunlight perpendicular incidence Keep the switch away from heat source
16. ould be taken to prevent power source interruptions m Provide the system with a dedicated grounding rather than sharing the grounding with the electronic equipment or lightning protection devices H Keep away from high power radio transmitters radar transmitters and high frequency strong circuit devices m Provide electromagnetic shielding if necessary 2 1 1 6 Rack Configuration The dimensions of the SS3GR1028F is designed to be mounted on a standard 19 2 3 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation rack please ensure good ventilation for the rack m Every device in the rack will generate heat during operation therefore vent and fans must be provided for an enclosed rack and devices should not be stacked closely BR When mounting devices in an open rack care should be taken to prevent the rack frame from obstructing the switch ventilation openings Be sure to check the positioning of the switch after installation to avoid the aforementioned Caution If a standard 19 rack is not available the SS3GR1028F can be placed on a clean level desktop leave a clearance of 100mm around the switch for ventilation and do not place anything on top of the switch 2 1 2 Installation Notice Read through the installation instruction carefully before operating on the system Make sure the installation materials and tools are prepared And make sure the installation site is well prepared During t
17. rack shelf under the switch Do not place anything on top of the switch Do not block the blowholes on the switch to ensure the proper operation of the switch 2 3 2 Connecting Console The SS3GR1028F provides a Mini USB serial console port Fig 2 2 Connecting Console to switch 2 6 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation The connection procedure is shown below 1 Find the console cable provided in the accessory kit Attach the Mini USB end to console port of the switch 2 Connect the other side of the console cable to a character terminal PC Power on the switch and the character terminal Configure the switch through the character terminal 2 3 0 SFP Transceiver Installation SS3GR1028F provide multiple 1000Mb SFP transceiver slots The procedure for installing SFP transceiver is shown below Step 1 Put on a ESD wrist strap or antistatic gloves Step 2 Insert SFP transceiver to the guide rail inside the fiber interface line card Do not put the SFP transceiver up side down Step 3 Push SFP transceiver along the guide rail gently until you feel the transceiver snap into place at the bottom of the line card Note SFP transceiver supports the hot swap Caution Do not stare directly at the 2 fiber bores in the SFP transceiver when the switch is in operation otherwise the laser may hurt your eyes 2 3 4 SS3GR10XFP Extended Module Installation The SS3GR1028F series prov
18. rosion of internal components Extreme low relative humidity may cause the insulation spacer to contract making the fastening screw insecure Furthermore in dry environments static electricity is liable to be produced and cause harm to internal circuits Temperature extremes can cause reduced reliability and premature aging of insulation materials thus reducing the switch s working lifespan In the hot summer it is recommended to use air conditioners to cool down the site And the cold winter it is recommenced to use heaters The recommended temperature and humidity are shown below Temperature Relative humidity Long term condition Short term condition Long term condition Short term condition 15 30 C 0 50 C 40 65 10 95 Table 2 3 Environmental Requirements Temperature and Humidity Caution A sample of ambient temperature and humidity should be taken at 1 5m above the floor and 0 4m in front of the switch rack with no protective panel covering the front and rear of the rack Short term working conditions refer to a maximum of 48 hours of continued operation and an annual cumulative total of less than 15 days Formidable operation conditions refers to the ambient temperature and relative humidity value that 2 2 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation may occur during an air conditioning system failure and normal operation conditions should be recov
19. s and strong electromagnetic interference sources WH The switch must be mounted to a standard 19 rack or placed on a clean level desktop 2 1 1 1 Dust and Particles Dust is harmful to the safe operation of the SS3GR1028F series switch Dust can lead to electrostatic adherence especially likely under low relative humidity causing poor contact of metal connectors or contacts Electrostatic adherence will result in not only reduced product lifespan but also increased chance of communication failures The recommended value for dust content and particle diameter in the site is shown below Max Diameter um Max Density 5 z 1 4x10 7x10 particles m Table 2 1 Environmental Requirements Dust In addition salt acid and sulfide in the air are also harmful to the switch Such 2 1 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation harmful gases will aggravate metal corrosion and the aging of some parts The site should avoid harmful gases such as SOz H2S NO2 NH3 and Clo etc The table below details the threshold value Average mg m Max mg m 0 2 0 006 Table 2 2 Environmental Requirements Particles 2 1 1 2 Temperature and Humidity Although the switch is designed to use 4 fans the site should still maintain a desirable temperature and humidity High humidity conditions can cause electrical resistance degradation or even electric leakage degradation of mechanical properties and cor
20. tablished otherwise the link is not ready and the cable should be examined Caution Please verify the sign above the port to ensure the right port used Connecting to wrong ports might damage the switch Fiber cables should be connected as below Step 1 Remove the protective plug from the SFP XFP SFP fiber transceiver bore Remove the protective cap from one end of the fiber cable Keep the fiber end clean and neat Step 2 Attach one end of the fiber cable to the SFP XFP SFP transceiver and attach the other end to the transceiver of the corresponding devices Note The SFP XFP SFP transceiver s TX port should be connected to the RX port of the corresponding device and vice versa Step 3 Check the fiber port status indicator a lighted LED indicates that the link has been established otherwise the link is not ready and should be examined Caution Please verify the sign above the port to ensure using the other ports Connecting to wrong ports might damage the transceiver or the other ports When connecting other devices through a fiber cable to the switch the output power of the fiber cable must not exceed the maximum received power of the corresponding modules Otherwise it will damage the fiber transceiver Do not stare at the fiber bore when the switch is in operation That may hurt your eyes 2 3 8 AC Power Supply Connection The SS3GR1028F series switches use 220V AC power supply by default Please read the power
21. vely ACL policies The traffic can be classified by 1 1 SS3GR1028F Series Installation Guide Chapter 1 Introduction source destination IP addresses source destination MAC addresses IP protocols TCP UDP IP precedence time ranges and ToS And various policies can be conducted to forward the traffic By implementing ACL policies users can filter the virus packets such as Worm Blaster Worm Sasser and Red Code etc Also supports IEEE802 1x port based access authentication which can be deployed with RADIUS to ensure the port level security and block illegal users QoS Fully supports DiffServ Module Users can specify a queue bandwidth on each port WRR SP SWRR scheduling is also supported Support the port trust Users can configure trusted CoS DSCP IP precedence and port priority User can also modify packet s DSCP and COS values The traffic can be classified by port VLAN DSCP IP precedence and ACL table User can also modify packet s DSCP and IP precedence values Users can specify different bandwidths for voice data video to customize different qualities of service lt 3D SMP Ready Supports a self defending security region management strategy It is supported interaction with some security system such as firewall IDS etc It can defense the virus and aggress effectively from the extranet and internet Thus enhance the security and stability of the network wide Perfect Web Management Support SNMP
22. voltage must be within the required range otherwise the switch can be damaged or malfunction Do not open the switch shell without permission It can cause physical injury 2 3 10 PoE Power Supply Connection When using PoE function of The SS3GR1028F it needs to connect the external PoE power with 5 holes socket The connection procedure is described as below 1 Insert one end of PoE power cable provided in the accessory kit into the external PoE power with overload and leakage protection and the other end to PoE power socket in the back panel of the switch 2 Connect PD device to the front port of SS3GR1028F 3 Check whether PD device is powered and the port indicator status shows the power 2 10 SS3GR1028F Series Installation Guide Chapter 2 Hardware Installation supply normally Caution The input voltage must be within the required range otherwise the switch can be damaged or malfunction PoE power supply of the front port is disabled when the switch is power off or is not started If there is any problem do not open the switch shell without permission It can cause physical injury 2 11
Download Pdf Manuals
Related Search