Code Corporation CR1400
Contents
1. mode and the trigger must be pressed to read a bar code refer to Section 4 0 Revision 1 Hardware of the CR1400 does not have an automatic stand detection feature to enable motion detection reading when the CR1400 is in a stand To configure this hardware revision for motion detection scanning please refer to the CR1400 Configuration Guide located at www codecorp com files php and scan the appropriate code See Section 10 0 to learn how to determine your CR1400 hardware revision number Ba C006819_04_CR1400_User_Manual 6 0 Reading Ranges CR1400 Performance Test Code Min Inches mm Max Inches mm 3 mil Code 39 3 1 80 mm 4 0 102 mm 7 5 mil Code 39 1 3 33 mm 7 2 182 mm 10 5 mil GS1 DataBar 0 8 20 mm 8 7 220 mm 3180mm 4 0 aoamm 08 20mm 87 220mm 11 0 280 mm 13 mil UPC 1 1 28 mm 4 2 mil Data Matrix 1 9 48 mm 4 3 110 mm 5 mil Data Matrix 1 7 43 mm 4 5 115 mm 1 3 33 mm 6 3 mil Data Matrix 5 9 150 mm e e 10 mil Data Matrix 0 8 20 mm 7 1 180 mm 20 8 mil Data Matrix 1 1 28 mm 13 5 343 mm Note working ranges are a combination of both the wide and high density fields All samples were high quality codes and were read along a physical center line at a 10 angle Default AGC settings were used Accuracy 10 7 0 Reader Feedback Scenario Top LED Light Sound Vibration CR1400 Su2. 2 J J NOTES pee GRANGE 8 __ __ _ 1 Part to be ROHS and Reach compliant YF cts erem 7 T 2 Maximum Voltage Tolerance 5V 10 10 GND os 24 AW 3 Caution Exceeding the maximum voltage will void manufacturer SHIELD warranty See Section 15 0 for complete reader pinouts descriptions fe co06819_04_CR1400_User_Manual 7 15 0 Reader Pinouts The connector on the CR1400 is an RJ 50 10P 10C The pinouts are as follows Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 16 0 CR1400 Maintentance The CR1400 needs only a minimum of maintenance to operate A few tips are given below for maintenance suggestions Cleaning the CR1400 The CR1400 window should be clean to allow the best performance of the device The window is the clear plastic piece inside the head of the reader Do not touch the window Your CR1400 uses CMOS technology that is much like a digital camera A dirty window may stop the CR1400 from reading bar codes If the window becomes dirty clean it with a soft non abrasive cloth or a facial tissue no lotions or additives that has been moistened with water A mild detergent may be used to clean the window but the window should be wiped with a water moistened cloth or tissue after using the detergent The following agents are approved to clean a Code bar code reader 1 Alcohol Wipes 2 CaviWipes Disinfecting Towlettes 3 Clorox Disinfecting Wipes 4 Clorox Bleach Solution 10 clorox bl
3. User Manual code Code Reader 1400 Manual Version 04 Release Date January 2013 leet C006819_04_CR1400_UserManual Statement of Agency Compliance rE The Code Reader 1400 CR1400 has been tested for compliance with FCC regulations and was found to be compliant with all applicable FCC Rules and Regulations IMPORTANT NOTE To comply with FCC RF exposure compliance requirements this device must not be co located or operate in conjunction with any other antenna or transmitter CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment The CR1400 has been tested for compliance to CE standards and guidelines and was found to conform to applicable CE standards specifically the EMC requirements EN 55024 ESD EN 61000 4 2 Radiated RF Immunity EN 61000 4 3 ENV 50204 EFT EN 61000 4 4 Conducted RF Immunity EN 61000 4 6 EN 55022 Class B Radiated Emissions and Class B Conducted Emissions Code voids product warranty if the hard case has been opened or tampered with in any way In addition a CB Test Certificate has been issued by the National Certification Board NCB indicating CR1400 meets all safety and quality standards in accordance to IEC 60950 1 2001 First Edition Ea C006819_04_CR1400_User_Manual Code Reader 1400 User Manual Copyright 2013 Code Corporation All Rights Reserved The software describ
4. a JJJ is the boot application version KKKK is the operating system kernel version m LLL is the root file system version lt TAB gt is the ASCII TAB character s the OEM decoder version a null terminated string of printable ASCII characters Without a decoder ini file order of the decoders listed here indicates the order of use Zahi the Example Xap i3000300006040010002363A06D SD SQ Note Code will periodically release new firmware for CR1400 readers For information on latest firmware versions call Code at 801 495 2200 To upgrade firmware please visit our website at http www codecorp com codesupport php and follow instructions provided Es C006819_04_CR1400_User_Manual 12 0 CR1400 Overall Dimensions 131 7 2 5 186 Ea C006819_04_CR1400_User_Manual 13 0 USB Cable Example with Pinouts Connector A Connector B WIRING TABLE See Section 15 0 for complete reader pinouts descriptions NOTES 1 Part to be ROHS and Reach compliant 2 Maximum Voltage Tolerance 5V 10 3 Caution Exceeding the maximum voltage will void manufacturer warranty 14 0 RS232 Cable Example with Pinouts Connector A Connector B Connector C 6 50 IN 0 5 IN T MATING PLUGS OD 3 5 mm CENTER PIN OD 2 0 mm LENGTH 6 5 mm INPUT 5 V MIN S00 mA e gt G Connector A T J WIRING TABLE i vn fawc reo s zawo Ro m 4 T BROWN
5. ccessfull A Green LED Flashes 1 Beep Handle Vibrates Powers Up CR1400 Successfully Once Enumerated Enumerates with Host 1 Beep Handle Vibrates the Green LED turns Off via cable Green LED Attempting to Decode None No Vibration Successful Decode and Green LED Flashes 1 Beep Handle Vibrates Data Transfer Configuration Code Successfully Decoded and Green LED Flashes 2 Beep Handle Vibrates Processed Configuration Code successfully decoded l Green LED Flashes 4 Beeps Handle Vibrates but wasn t successfully processed fe co06819_04_CR1400_User_Manual 3 8 0 Symbologies Defaulted On The following are symbologies that have a default of ON To turn symbologies on or off scan the symbology bar codes located in the CR1400 Configuration Guide located on our website at http www codecorp com Aztec All GS1 DataBar Codabar Interleaved 2 of 5 Code 39 PDF417 Code 93 QR Code Code 128 UPC EAN JAN Data Matrix Data Matrix Rectangle 9 0 Symbologies Defaulted Off The following are symbologies that have a default of OFF To turn symbologies on or off scan the symbology bar codes located in the CR1400 Configuration Guide located on our website at http www codecorp com Aztec Inverse Matrix 2 of 5 Code 11 Micro PDF417 Code 32 Micro QR Code 39 Extended Full ASCII MSI Plessey Code 39 Checksum Plessey Composite QR Code Inverse Data Matrix Inverse Straight 2 of 5 Han Xin Trioptic UPC E Expansion UPC Supp
6. csccsccsccsccsccsccsccccescesceccnccesceccnccescecceccsccecceccscceccecsccsccecoscescesceeces 15 0 REAGEN PINOUNS ssesienipeteencstsnscannsessarepaseteieanses EAN E EEE E E S AE 16 0 Mamta NCE ssas naa A EEE ENEE SEEEN RE ESAERAREN AEO EANN ETa 17 0 War anty sassancacansnncsisucastnsucnsdevannsaeiucdassnsaanenenavnstanvevseseuaseucnnsanadacsouaenesdnsesenvdagasnsaesawtanesesannesansuasenvaciesueseseatetesesngatssmas Ea C006819_04_CR1400_User_Manual 1 0 Unpacking Remove the CR1400 from its packing and inspect it for damage If the reader was damaged during shipping please call Code at 801 495 2200 Depending on the kit ordered a USB or RS232 Affinity cable has been included with your reader USB Affinity Cable RS232 Affinity Cable w Power Supply 2 0 Attaching and Detaching a Cable To attach a cable plug the RJ 50 end of the Affinity cable into bottom of the reader handle Figure 1 Firmly push the connector into the reader until a snap can be heard to indicate the cable is properly attached To detach a cable press a paper clip into the hole on the side of the CR1400 handle Figure 2 and gently pull the cable from the reader Figure 1 Figure 2 3 0 Powering On Off the Reader For USB Cable plug the USB end of the Affinity cable into a USB port on the host device After several seconds the reader will beep twice the reader will vibrate and the LED will turn off to indicate the CR1400 is ready
7. cts must be shipped in the original or comparable packaging with shipping and insurance charges prepaid Only parts listed in the original RMA should be sent and will be accepted Code will pay for return shipping and insurance of repaired or replacement products worldwide Code will use new or refurbished parts at its discretion and will own all parts removed from repaired products Customer will pay for any pre shipped replacement product in case it does not return the replaced product to Code within 7 days of receipt of the replacement product The process for return and customer s charges will be in accordance with Code s Exchange Policy in effect at the time of the exchange Customer accepts full responsibility for its software and data including the appropriate backup thereof Repair or replacement of a product during warranty will not extend the original warranty term Return time frames are listed in the chart above For RMA s not covered under warranty as outlined in the exclusion section customer will be required to pay the non covered warranty fee as listed in the chart above General EXCEPT FOR THE WARRANTIES STATED ABOVE CODE DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED ON PRODUCTS FURNISHED HEREUNDER INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT The stated express warranties are in lieu of all obligations or liabilities on part of Code for damages inc
8. each 90 tap water 5 Medical DiAirKem 6 Sani Cloth HB Super Sani Cloth Germicidal Sani Cloth Plus Germicidal Disposable Wipes 7 Virex II Disinfectant Cleaner Technical Support and Returns For returns or technical support call Code Technical Support at 801 495 2200 For all returns Code will issue an RMA number which must be placed on the packing slip when the reader is returned Visit http www codecorp com codesupport php for more information Ba C006819_04_CR1400_User_Manual 8 17 0 Warranty Code s CR1400 carries a five year limited warranty as described herein Universal Stands follow the warranty of the reader and Cables have a 90 Day warranty period Limited Warranty Code manufactures its hardware products in accordance with industry standard practices Code warrants its products will be free from defects in materials and workmanship provided that the products are used under normal operating condition intended by the Manufacturer This warranty is provided to the original owner only and is not transferable to any third party This warranty is subject to any and all accompanying disclaimers limitations and other terms of this section Warranty periods are not extendable beyond 5 years CodeOne extended warranty programs are available and must be purchased within 90 days of purchase Please refer the CodeOne Data Sheet for program pricing and terms and conditions Exclusions No warranty herein contained or
9. ed in this manual may only be used in accordance with the terms of its license agreement No part of this publication may be reproduced in any form or by any means without written permission from Code Corporation This includes electronic or mechanical means such as photocopying or recording in information storage and retrieval systems NO WARRANTY This technical documentation is provided AS IS Further the documentation does not represent a commitment on the part of Code Corporation Code Corporation does not warrant that it is accurate complete or error free Any use of the technical documentation is at the risk of the user Code Corporation reserves the right to make changes in specifications and other information contained in this document without prior notice and the reader should in all cases consult Code Corporation to determine whether any such changes have been made Code Corporation shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from the furnishing performance or use of this material Code Corporation does not assume any product liability arising out of or in connection with the application or use of any product or application described herein NO LICENSE No license is granted either by implication estoppel or otherwise under any intellectual property rights of Code Corporation Any use of hardware software and or technology of Code Corporation i
10. for use For RS232 Cable plug the power supply into the AC outlet plug the power supply cord into the barrel jack of the cable and connect the RS232 connector to the appropriate serial port on the host device After several seconds the reader will beep twice the reader will vibrate and the LED will turn off to indicate the CR1400 is ready for use Paks C006819 04 CR1400_ User _Manual 1 4 0 Using a CR1400 Out of a Universal Stand Press and hold the CR1400 trigger the two blue bars emitting from the reader are used for targeting Center the blue bars in the middle of a bar code The optimal reading distance from reader to bar code is approximately 4 0 10 cm Once the reader is at the optimal distance the reader will read the bar code The CR1400 will beep flash a green LED and vibrate to indicate a good read has occurred To modify any default settings download the CR1400 Configuration Guide at www codecorp com files php and scan the appropriate code 5 0 Using a CR1400 in a Universal Stand Revision 2 Hardware of the CR1400 has a stand detection feature By default when the CR1400 is placed in the stand the reader will automatically enter into motion detection mode When in this mode simply place a bar code in the scan field to activate the reader The CR1400 will beep and flash a green LED to indicate a good read has occurred When the CR1400 is removed from the stand the reader switches to manual
11. lemental 10 0 Locating the Hardware Revision Number Locate the serial label on the bottom of the reader to identify the hardware revision number of the CR1400 Serial 20000XXXX MFG CR1411 Designed in USA The number after the underscore _ represents the hardware revision number Made in Malaysia Ba C006819_04_CR1400_User_Manual 4 11 0 Reader ID and Firmware Version To find out the Reader ID and firmware version open a text editor program i e Notepad Microsoft Word etc and read the following code Reader ID and Firmware z r M0148_01 You will see a text string indicating your firmware version and CR1400 ID number see below iVVVVWWWWXXXXSSSSSSSSSSAOODYYYYH HIHIJJJJKKKKLLLL lt TAB gt Z Z i indicates string output VVVV is the application firmware version number WWWW is the core application firmware version number XXXX is reserved for the radio firmware version number SSSSSSSSSS is the Reader s serial number ten digits is the current execution state A means core is running B means undefined C means undefined O is the OEM identifier is the display type TS 0 or N is no display device D is the standard Keypad Display YYYY is the flash file system version number Reserved S i gt i RF L H is the hardware revision Ill is the hardware type identifier 0008 indicates a CR1400
12. luding without limitation special indirect or consequential damages arising out of or in connection with the use or performance of the product Seller s liability for damages to buyer or others regardless of the form of action whether by contract warranty tort malpractice and or otherwise resulting from the use of any product shall in no way exceed the purchase price of said product In no event shall Code be liable for any consequential special indirect incidental or punitive damages or for any loss of profits revenue or data even if Code has been advised of the possibility thereof Paks C006819_04_CR1400_User_Manual
13. s governed by its own agreement The following are trademarks or registered trademarks of Code Corporation CodeXML Maker QuickMaker CodeXML Maker CodeXML Maker Pro CodeXML Router CodeXML Client SDK CodeXML Filter HyperPage CodeTrack GoCard GoWeb ShortCode GoCode Code Router QuickConnect Codes Rule Runner Cortex CortexRM CortexMobile Code Code Reader CortexAG CortexStudio CortexTools Affinity and CortexDecoder All other product names mentioned in this manual may be trademarks of their respective companies and are hereby acknowledged The software and or products of Code Corporation include inventions that are patented or that are the subject of patents pending U S Patents 6997387 6957769 7428981 6619547 6736320 7392933 7014113 7240831 7353999 7519239 7204417 6942152 7070091 7097099 7621453 8001550 8011584 The Code Reader software uses the Mozilla SpiderMonkey JavaScript engine which is distributed under the terms of the Mozilla Public License Version 1 1 The Code Reader software is based in part on the work of the Independent JPEG Group Code Corporation 14870 South Pony Express Road Suite 200 Bluffdale UT 84065 www codecorp com Paks C006819_04_CR1400_User_Manual Table of Contents DOD ACN sais csececas xessccce E E wos lt oeeeecieseneeeussshecaucncueeaccreeudsnte E 2 0 Attaching Deta ching a Cable vosancvinnsaievesnzacensioneda vn vanen usennedionsvedewsauiess
14. set out shall apply to any product i which has been repaired altered or tampered with unless done or approved by Code ii which has not been maintained in accordance with any operating or handling instructions supplied by Code iii which has been subjected to unusual physical or electrical stress immersion in fluids puncture crushing misuse abuse power shortage improper power supply such as incorrect voltage or wrong polarity negligence or accident or iv which has been used other than in accordance with the product operating and handling instructions Preventive maintenance is the responsibility of the customer and is not covered under this warranty Warranty Coverage and Procedure During the warranty period Code will repair or replace defective products returned to Code s service center in the US For worldwide warranty service go to http www codecorp com technical support php and fill out a service request Customer will be issued a case number Case will be routed into the support queue within Code Customer will be contacted within one business day of submission Code representative will work with customer to troubleshoot solution and attempt to restore reader to proper functionality If the Code representative determines that it cannot be restored programmatically and deems a hardware issue is found a Return Material Authorization RMA Number will be assigned and customer will be instructed to return the product to Code Produ
15. uvannsuacwesevonadpuenaswasesuseeenuieaensnvenguesdesunoonesaseoumyangancees 3 0 Powering the Reader On Off sssesossesssesssssosssosssosssosssoosssosesosssossssosssosesosesossssssesosssosssosssosssosssosseossssosssosssesssessssoo 40 Using a CR1400 Out of a Stand wick cavctis cxcctececwevccescccecwaxecexcvedanvetaucersvensecavsiucawnievcucnsuacexncsedaswcneteteouscettexcddceiwiacvecensenites 5 0 Using a CR1400 Mn a StaNUeismesrnisaricireroiada aiaiai n aaa a aai is 60 Reading Rahe Esia aer EA EEEN NT cise civ E ENE EA A EEEE E sn sewacenseeeusceedonseceees 7 0 R ader Feedbatk scrisse a E E EN E A 8 0 Symbologies Defaulted ON isssissssesssissansssssssnstsssnzssssossnerssssdanovorsris svor d torons kotoo takn Non rsen ir P nnan orenian k o issar n s Kis iEsis 9 0 Symbologies Defaulted Off eeseseoessesecececsosecececscsesececeososececeososesececeososececeoeoseseceosososececeososesececeososeseceoscseseceseeseses 10 0 Locating the Hardware Revision Number sessssssesessosecececsosesececeososececeososesececeososececsososesececsesesececessesesesecseseseceosee 11 0 Reader ID amp Firmware Version sisses irena AN E EEEE E E ESS 12 0 CR1400 Overall DIMENSIONS issocsserdsccssecscccava vente rE EA E ROEE EAS 13 0 USB Cable Example with PINQUNS seisnssiniicivnasunecarcsiuevessscucesavedeseacicsadsevesensusunswbasvdasedaenasnasvausssusarsescuaenissesceuededosveenees 14 0 RS232 Cable Example with Pinouts ccsccsccec
Download Pdf Manuals
Related Search