StarTech.com USB Dual VGA over Cat5 KVM Console Extender - 650 ft / 200m
Contents
1. Beep Codes Some of the keyboard command sequences you issue to the Remote Unit have multiple possible settings The Unit will beep to indicate what setting you have selected for the command you issued A short beep followed by a long beep indicates an invalid command Ctrl Ctrl Alt E Compatibility Mode Selection 1 beep disabled factory default 2 beeps enabled Note Commands described in the Key Key format are keys that must be pressed in order on the keyboard Commands described in the Key Key format must be pressed simultaneously Note If the NumLock CapsLock and ScrollLock lights are flashing in unison on the keyboard the other Unit has control of Computer A You will not be able to use A until the other Unit releases access to that computer StarTechg om 14 Hard to find made easy Instruction Manual Specifications Maximum 1920 x 1200 at maximum UTP cable iui Resolution Maximum Range 650 feet 200 meters _ Tice Le Strailge MR Unshielded Twisted Pair UTP Cat 5 Each Local and Remote Unit 4x HD 15 female 2 x KVM 2 x console VGA Connectors 2 x RJ 45 2 x USB keyboard mouse for console 1 x Power optional ov DC 600mA center positive per rd Power Adapter Optional only required when connected using a conventional KVM switch StarTechg om 15 Hard to find made easy Instruction Manual RJ 45 Connector Pinout Instruction Manual Wire Color White Orang2. Unit immediately takes control of the system Local On The LED Local lights up the connected PC or KVM Switch is controlled by the Local Unit In this case 3 LEDs Num Caps and Scroll Lock flash on the keyboard attached to the Remote Unit Remote On The LED Remote lights up the system can be remotely controlled by the Remote Unit StarTechg om 6 Hard to find made easy Instruction Manual Video Compensation Video Compensation allows the user to adjust the equalization from the Remote Unit console to optimize video performance based on the length of cable being used as well as other factors that may affect the display with adjustments available for Equalizer Sharpness Gain Brightness and Skew RGB To compensate the varying lengths of CAT 5 CAT 5e CAT 6 cable there 16 levels on coarse tune and up to 128 256 scales on fine tune are available for adjustment on the equalizer and gain There are also 8 levels on coarse tune and 16 32 scales on fine tune are available for skew adjustment on Red Green and Blue Please refer to the section below titled Hotkey Commands for Remote Unit for details on how to apply video compensation settings After Video Compensation Note 1 The video adjustment is available on the Remote Unit ONLY 2 The video adjustment is applicable only if the CATx cable is connected and the Remote Unit is in control 3 The idle time out of Video Adjustment is 30 seconds
3. standard Category 5 5e 6 patch cables at both locations if using premises cabling StarTechg om 1 Hard to find made easy Instruction Manual NOTE The total length of cable between the Local and Remote Units cannot exceed 650 feet 200 meters including patch cables if used It is suggested using Cat5 cables with identical brand and length when connected simultaneously Category 5e and 6 cabling is compatible with this product and may improve performance NOTE Long cable lengths between the Local and Remote Units may adversely affect image quality at high resolutions and refresh rates If you need to run your remote displays at high resolutions and frequencies use as little cabling between locations as possible and avoid practices such as coiling unused cable in a ceiling NOTE This product will also control a KVM switch allowing you to manage more than one computer remotely In this configuration you can connect the KVM extender s Local Unit to the console ports on the KVM You must use the provided power adapters if using this configuration You should set the Local Unit to Compatibility Mode before connecting it to a KVM that uses the Ctrl key as its hotkey sequence see Hotkey Commands page 8 for details Packaging Contents 1x Local Unit 1x Remote Unit 2x6 ft 2 in 1 USB VGA KVM cables 2x Packs Rubber Feet 1x Power Adapter e 1x Instruction Manual StarTechg om 2 Hard to find made easy Instructi
4. the products you need in no time Visit www startech com for complete information on all StarTech com products and to access exclusive resources and time saving tools StarTech com is an ISO 9001 Registered manufacturer of connectivity and technology parts StarTech com was founded in 1985 and has operations in the United States Canada the United Kingdom and Taiwan servicing a worldwide market
5. used Adjust 1st Monitor first use F1 F4 and then 2nd Monitor second use F5 F8 Please refer to Video Adjustment section for more details adjustment Instruction Manual StarTechg om 17 Hard to find made easy Symptom Solution Keyboard hotkeys are inoperable when the KVM Apply compatibility mode hotkey commands Extender connects with the Verify if the Extender has enough power KVM Switch Verify if the units have enough power If the power is insufficient for the needs purchase a power adapter from your local dealers Computer units are inoperable Problems continue to occur after checking the solutions above Remove and reinstall each device checking the connectors and sockets for bent pins or other damage StarTechg om 18 Hard to find made easy Instruction Manual Technical Support StarTech com s lifetime technical support is an integral part of our commitment to provide industry leading solutions If you ever need help with your product visit www startech com support and access our comprehensive selection of online tools documentation and downloads For the latest drivers software please visit www startech com downloads Warranty Information This product is backed by a three year warranty In addition StarTech com warrants its products against defects in materials and workmanship for the periods noted following the initial date of purchase During this period the products m
6. StarTechg om Hard to find made easy USB Dual VGA Cat5 KVM Console Extender 650ft 200m SV565DUTPU actual product may vary from photos DE Bedienungsanleitung de startech com FR Guide de l utilisateur fr startech com ES Gu a del usuario es startech com IT Guida per l uso it startech com NL Gebruiksaanwijzing nl startech com PT Guia do usu rio pt startech com For the most up to date information please visit www startech com Manual Revision 06 26 2012 FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a
7. That is it will automatically escape from video adjustment status if no activity is detected by the keyboard within 30 seconds You can activate video adjustment on the Remote Unit either through hotkeys or push button The Unit is capable of hotkey control whether the Mask Hotkey is OFF or ON When the Video Adjustment mode is activated the Numeric Lock and Scroll Lock LED on the keyboard connected to the Remote Unit will flash respectively Then you can perform the video adjustment by hotkey commands as the table shown below To exit the video adjustment status three approaches are available 1 No activity is detected by the keyboard for 30 seconds 2 Push the Esc key once on the keyboard attached to the Remote Unit 3 Push the push button on the top panel of the Remote Unit once StarTechg om 7 Hard to find made easy Instruction Manual Hotkey Commands A hotkey command is a short key sequence to select a computer activate computer scan and so forth The KVM Extender interprets keystrokes for hotkeys all the time And the built in buzzer generates a high pitched beep for correct hotkey command otherwise one short and one long beep are generated for a bad command in which the bad key command won t be sent to the extender unit or the selected computer Cascade Architecture The KVM Extender can be connected to the console ports of a KVM Switch however to prevent any conflict via hotkey commands the hotkey commands prefi
8. Unit Two beeps Enable Compatibility Mode and the users at Local Unit accessing to the KVM switch that is connecting to the Local Unit Reset the Unit to the factory default Escape from hotkey mode Mode selection i in Sequence Switch console control between Local Computer and Remote Computer Local mode selection Remote Unit Enable the user at the Remote Unit accessing to the computer KVM Switch that connects to the Remote Unit Local Unit Enable the user at Local Unit exclusive accessing to the PC KVM Switch that connects to Local Unit Disables the Remote Unit user accessing StarTechg om 10 Hard to find made easy Hotkey Commands Keyboard Push Button 2 N A F12 V 4 Digits For both 1st amp 2nd Monitors Mouse resynchro Function Descriptions Remote mode selection Enable the user at the Remote Unit exclusive accessing to computer KVM Switch that connects to the Local Unit only if the Local Unit is in Remote or Auto mode Disable Local Unit user accessing to the Local Unit during this mode ized for PS 2 PC EDID Configuration EDID Emulation Prevent the video resolution setting from exceeding the capability of the connected display require CPU reboot the following options for video resolution V IM 4 Digits For 1st Monitors are available for selecting Input 4 digits with 1007 for resolution of 1024 x 0768 1210 for resolution of 1280
9. Unit B Local Unit in Auto mode Remote Local LED flashes alternatively One beep Enable the output video signal of Local Unit Two beeps By triggering keyboard mouse users can disable the output video signal of Local Unit temporarily The Local Unit users protect the privacy for 5 15 30 and 60 seconds See the above table Latch time selection for more descriptions Three beeps By triggering keyboard mouse the Remote Unit or Local Unit users can temporarily disable the output video signal of the other Unit The users protect the privacy for 5 15 30 and 60 seconds as well StarTechg om 12 Hard to find made easy Instruction Manual Hotkey Commands for Remote Unit The Video Adjustment function is on Remote Unit only To launch its hotkey command also start with the specific leading code depending on situation and then press F11 to enter Video Adjustment Mode After adjustment just press Esc to escape from this Mode Hotkey Commands 2 imm Function Descriptions Push Button Keyboard Equalizer Gain Adjustment Equalizer Sharpness Num Lock LED Caps Lock LED Flashing 1 For both 1st and 2nd monitors 1 1 Press lt or gt to coarse tune 16 levels for adjustment 1 2 Press and Hold Shift 4 amp or gt to fine tune 2 For 1st Monitor Num Lock LED Caps Lock LED Flashing 2 1 Press F1 or F2 to coarse tune 16 levels for adjustment 2 2 Press and Hold Shift F1 or F2 to fine tune 3 F
10. ay be returned for repair or replacement with equivalent products at our discretion The warranty covers parts and labor costs only StarTech com does not warrant its products from defects or damages arising from misuse abuse alteration or normal wear and tear Limitation of Liability In no event shall the liability of StarTech com Ltd and StarTech com USA LLP or their officers directors employees or agents for any damages whether direct or indirect special punitive incidental consequential or otherwise loss of profits loss of business or any pecuniary loss arising out of or related to the use of the product exceed the actual price paid for the product Some states do not allow the exclusion or limitation of incidental or consequential damages If such laws apply the limitations or exclusions contained in this statement may not apply to you Starlechcom 19 Hard to find made easy Instruction Manual Starlechcaom Hard to find made easy Hard to find made easy At StarTech com that isn t a slogan It s a promise StarTech com is your one stop source for every connectivity part you need From the latest technology to legacy products and all the parts that bridge the old and new we can help you find the parts that connect your solutions We make it easy to locate the parts and we quickly deliver them wherever they need to go Just talk to one of our tech advisors or visit our website You ll be connected to
11. circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Use of Trademarks Registered Trademarks and other Protected Names and Symbols This manual may make reference to trademarks registered trademarks and other protected names and or symbols of third party companies not related in any way to StarTech com Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech com or an endorsement of the product s to which this manual applies by the third party company in question Regardless of any direct acknowledgement elsewhere in the body of this document StarTech com hereby acknowledges that all trademarks registered trademarks service marks and other protected names and or symbols contained in this manual and related documents are the property of their respective holders Starlechcom Hard to find made easy Instruction Manual Table of Contents ide Tee dre tS 1 pU crsm E EETEEME 1 System Requirements nene e NIRE THER ARAE 1 sre tT Info Rao Tni A EE 2 Connecting Your KVM Extender Preparing Your Site ACIEM M 4 nstalling thieLocal WMI ssc sscviesnesdsecoeacsessbonssss etnnrdvaattavoeosubasssinedaseaceieaens recte Recto PRI rere ton Od 4 nstalling the Remote Unt aoc teen eid Rr te pp dca ies 4 Push Button Control and LEDS
12. e Orange White Green Blue White Blue Green White Brown Brown Pair Function StarTechg om Hard to find made easy Troubleshooting If you encounter problems with the KVM Extender during the installation or operations please check through this section for a possible solution If your problem is not listed here and you can not resolve the issue please contact your local dealer for the fastest assistances Symptom No video signal Poor video quality 2 monitors 1st and 2nd on Remote Unit can t simultaneously display improved video quality after Solution Verify that all the cables are qualified according to the hardware requirement section Verify that all the cables are properly connected to their ports and are firmly seated Use an alternative CATx cable connection between the unit of con sole and computer Use CATx cables with identical brand and length when connected simultaneously Use CATx cables for the connection between the respective RJA5 port Cat5 1 to Cat5 1 Cat5 2 to Cat5 2 on each Unit Power down the computer Connect the monitor directly to the computer and power up again If the monitor does not operate correctly direct to the Use the EIA TIA 568B industry standard CATx cable for KVM Extender connection Unplug the CATx cable s from the Extender then plug it them back in Perform the video quality adjustment for the length of CATx being
13. on Manual Connecting Your KVM Extender Preparing Your Site Before you can install the product you need to prepare your site 1 Determine where the local computer will be located and set up the computer 2 Determine where the console devices mouse keyboard monitor will be located and place them appropriately 3 a If you are using surface cabling ensure you have enough Category 5 unshielded twisted pair UTP network cabling to run two cables from the Local Unit to the Remote Unit s location and that each end is terminated with a RJ 45 connector OR b If you are using premises cabling ensure that the Category 5 unshielded twisted pair UTP network cabling between the Local Unit and the Remote Unit has been properly terminated into wall outlets in each location and there is a patch cable long enough to connect the Remote Unit and the Local Unit to their respective outlets CAT52 EE 7T T t CAT5 1 amp Option Option VGA Cable KVM Cable KVM KB MS VGA Cable KVM Cable KVM KB MS Remote Unit E Option Local Unit i StarTechg om Instruction Manual 3 Hard to find made easy Installation Installing the Local Unit 1 2 Place the Local Unit near the computer Switch off the computer and disconnect any connected devices 3 Using the provided StarTech com integrated KVM cable connect the end of the cable that has the USB or PS 2 VGA connectors to the VGA O
14. on on Remote Unit The button on the top panel of Remote Unit can be used to switch mode between Local and Remote in the sequence as the diagram shown below p Local On Remote On gt Local On When the LED Local lights up the system controls its local computer Remote On When the LED Remote lights up the system remotely controls the Local Unit Push Button on Local Unit The button on the top panel of Local Unit can be used to switch mode among Local Remote and Auto in the sequence as the diagram shown below p Auto Local On Remote On J Auto The LEDs Remote and Local flash alternatively the system is now waiting for the Remote or Local Unit to take control The control priority is on the first come first served basis For example once the keyboard or mouse attached to the Local Unit is active the LED Local will light up and the LED Remote will light off This status indicates that the Local Unit is now taking control of the system and vice versa for Remote Unit In Auto mode the duration of latch time for taking control can be preset to 5 15 30 or 60 seconds via hotkeys which allows the Local or Remote Unit to resume control again via any keystroke or mouse activity if the latch time is due and the status returns to the Auto mode In Auto mode whenever any activity from the keyboard mouse buttons or mouse scroll wheel is detected the Unit Local Unit or Remote
15. or 2nd Monitor Num Lock LED Caps Lock LED Flashing E 3 1 Press F5 or F6 to coarse tune 16 levels for adjustment 3 2 Press and Hold Shift F5 or F6 to fine tune Gain Brightness Caps Lock LED Scroll Lock LED Flashing 1 For bot stand 2nd monitors or 1 1 Press to ag Wes 6 levels for adjustment 1 2 Press and Hold Shift or Y to fine tune 2 For 1st Monitor Num Lock LED Caps Lock LED Flashing 2 1 Press F3 or F4 to uei ae 16 levels for adjustment 2 2 Press and Hold Shift P or Y to fine tune 3 For 2nd Monitor Num Lock LED Caps Lock LED Flashing 3 1 Press F7 or F8 to coarse tune 16 levels for adjustment 3 2 Press and Hold Shift F7 or F8 to fine tune StarTechg om 13 Hard to find made easy Instruction Manual Hotkey Commands WEROTVEEPU STEPH IRE QHTTEO ROTER EAT z Function Descriptions Keyboard Push Button Blue Green Red Color Adjustment Caps Lock LED Flashing B Blue 1 For both 1st and 2nd monitors Eug 1 1 Press or 3 to coarse tune 8 levels for adjustment G Green 1 2 Press and Hold Shift lt or gt to fine tune R Red 2 For 1st monitor 2 1 Press F1 or F2 to coarse tune 8 levels for adjustment Choose one color at a time 2 2 Press and Hold Shift F1 or F2 to fine tune for adjustment 3 For 2nd Monitor 3 1 Press F5 or F6 to coarse tune 8 levels for adjustment 3 2 Press and Hold Shift F5 or F6 to fine tune Esc Escape from Video Adjustment Mode
16. priate The PS 2 version of the cable is color coded Connect the opposite end of the cable with a single connector to the gray coded connector marked COMPUTER on the Remote Unit of the KVM extender Use Video cable for the connection between the video port on the computer side of the Unit and the video output port of the connected Computer Use Video cable for the connection between the video port on the console side of the Unit and the video input port of the connected monitor Use a CAT5 cable for the connection between the respective RJ45 port Cat5 1 amp Cat5 2 on the Remote and Local Unit StarTechg om 4 Hard to find made easy 7 Connect a USB mouse keyboard and a VGA monitor to the indicators marked as CONSOLE on the Remote Unit 8 Connect the UTP cable connections for Remote Unit to the NETWORK RJ 45 connector on the Remote Unit Connect the opposite end to a terminated wall outlet if using premises cabling CAUTION The UTP network cables that connect the Local and Remote Units carry electrical current and should not be plugged in to other devices as they may cause damage We strongly recommend marking the cables you are using with this product at both locations for easy identification StarTechg om 5 Hard to find made easy Instruction Manual Push Button Control and LEDs A push button on the respective top panel of Local Unit and Remote Unit can be used to select the control mode Push Butt
17. sessesessesesesssseseseseeseseseoseseseesesesesseses 6 Push Button on Remote Units tre ertt ovt cte E e tpe ta ian 6 Push B ttorion EOoCalUnit 55 55 m ecritrreterl tetra rod Bone ber etes er ee bor RA een 6 Video Compensation zc ctiani rmtttotnel RaR ER ERRi 7 Hotkey Commands Cascade Architecture Mask Hotkey Switch Hotkey Commands for both Remote Unit and Local Unit 10 Hotkey Commiands for Local Unitassoserononnonnnsnssisnmmonakenonomininnisai 12 Hotkey Commands for Remote Umit sccvicccscssscssssconssesssssssscssssssseisenssnedscosacassneibasseesonsensossaiasassesssdoaasieie 13 SII ID 14 SPECIICATIONS sesiassaissesccssescescecasosdecsatacccdsacenstesssesosdanscsacseassisestecaeacsseees este 15 RJ 45 Connector PiNOUt sssss ssssesossssossssssosssssusuosssesssssnsssersasssssev ssssessosoe 16 TROUDIESHOOTING e A 17 Technical Support Warranty Information oett terat eoe eot rete vna reb verae sosta 19 TT StarTechycom i Hard to find made easy Introduction The SV565DUTPU USB Dual VGA KVM Console Extender over CAT5 UTP lets you Operate a Dual VGA PC or KVM switch up to 650ft 200 m away as if it was installed locally at high definition 1920x1200 resolution PC connection cables are included with this product for a ready to use solution The dual VGA Cat5 KVM extender supports easy to use hot key and push button commands which allow you to switch between a locall
18. the keyboard within 3 seconds after the leading code input when Mask Hotkey OFF or within 6 seconds after BTN 2sec when Mask Hotkey ON Press the button Esc once to escape from the hotkey mode Press the Push Button once to escape from the hotkey mode and switch to either the Local or Remote mode Before inserting the hotkey commands it s required to launch the leading code refer to the diagram above according to different situations and succeed by one or two more keystrokes as the following charts show NOTE Hotkeys should be entered using the top row numbers and the left Ctrl Alt Shift keys only OFF ON Nis Mask tL Hotkey Instruction Manual Sta Tech om 9 Hard to find made easy Hotkey Commands for both Remote Unit and Local Unit Before inserting the hotkey commands it s required to launch the leading code Ctrl Ctrl or Ctrl Ctrl Hotkey Commands Keyboard Alt E Esc T 1 Instruction Manual Push Button N A N A E depending on Cascade Architecture Function Descriptions Cascading status selection both Units One beep Enable Standard Mode Remote Unit Two beeps Enable Compatibility Mode and the user at Remote Unit accessing to the KVM switch that is connecting to Local Unit Local
19. ut connectors and the USB or mouse and keyboard PS 2 connectors on the computer as appropriate The PS 2 version of the cable is color coded Connect the opposite end of the cable with a single connector to the gray coded connector marked COMPUTER on the Local Unit of the KVM extender Use Video cable for the connection between the video port on the computer side of the Unit and the video output port of the connected Computer Use Video cable for the connection between the video port on the console side of the Unit and the video input port of the connected monitor Use a CAT5 cable for the connection between the respective RJ45 port Cat5 1 amp Cat5 2 on the Remote and Local Unit If you wish to have console access to the local computer connect a USB mouse keyboard and VGA monitors to the indicators marked as CONSOLE on the Local Unit Connect the UTP cable connections for Remote Unit to the NETWORK RJ 45 connector on the Local Unit Connect the opposite end to a terminated wall outlet if you are using premises cabling Installing the Remote Unit 1 2 3 Instruction Manual Place the Remote Unit near the computer Switch off the computer and disconnect any existing VGA and input connections Using a StarTech com integrated KVM cable connect the end of the cable that has the USB or PS 2 VGA connectors to the VGA Out connectors and the USB or mouse and keyboard PS 2 connectors on the computer as appro
20. x 1024 1612 for resolution of 1600 x 1200 V IS 4 Digits For 2nd Monitors 1912 for resolution of 1920 x 1200 1914 for resolution of 1920 x 1440 2011 for resolution of 2048 x 1152 NOTE By default the EDID Configuration EDID Emulation setting between the Remote Unit and Local Unit will follow the Remote Unit setting after reboot The following options for video resolution are available for selecting 4 Digits Resolution 4 Digits Resolution 1007 l 1024 x 768 Bn 1612 1600 x 1200 14 09 1440 x 900 l 19 14 l 1920 x 1440 TUN Starlech om 11 Hard to find made easy Hotkey Commands for Local Unit Hotkey Commands SS ES SRST a j Function Descriptions Keyboard Push Button 3 N A Auto Mode Selection Latch Time Selection F3 Auto Mode latch time setting The extender generates 1 to 4 beeps to indicate the duration of latch time 5 15 30 60 seconds respectively Privacy setting enable F6 Ne Enable the Local Unit stop Video Signal Privacy Setting Enable Please identify the current mode in either Local or Auto mode by checking the Local Unit LED first then through repeating the hotkey commands for privacy setting Leading Code F6 the KVM Extender generates 1 to 3 beeps to indicate the statuses of the Local Unit as follows A Local Unit in Local mode Remote LED Off Local LED On One beep Enable the output video signal of Local Unit Twoorthree beeps Disable the output video signal of Local
21. xed with Compatibility mode leading code can be applied for directly accessing to the KVM Extender Mask Hotkey Switch The hotkey commands of KVM Switches vary among models which may cause hotkey errors unwanted configurations between the Extender Unit and mixed types of KVM Switches that connect to each other The Mask Hotkey extremely simplifies the hotkey control in cascade architecture Cascade Mask Aree E Hotkey Hotkey Commands Switch Standard Mode factory default The hotkey command starts with the leading code left Ctrl left Ctrl NO OFF followed by one or two more keystrokes Only the key Ctrl located on the lower left corner of the keyboard is eligible for hotkey commands Compatibility Mode Users can configure the computer attached to the KVM Switch by applying the KVM Extender built in hotkey command prefixed with the cascade leading code left Ctrl left Ctrl E YES OFF The state of the KVM Extender with or without connection s to KVM Switch es Users can apply built in hotkey commands of its KVM Switch es or use the KVM YES NO ON Extender alternative hotkey command with the button maneuvering Press amp Hold push button 2 Sec followed by one or two more keystrokes In later descriptions this action will be simplified as BTN 2sec StarTechg om 8 Hard to find made easy Instruction Manual NOTE The hotkey command will be automatically time out if There is no activity detected by
22. y connected system and your remote server or KVM and works with virtually any standard USB keyboard and mouse including wireless sets The hot key commands also provide video adjustment controls for optimizing picture quality over varying distances Extending over two standard Cat5 or better cables gives you the ability to use existing infrastructure wiring to achieve remote access to your server or KVM switch Backed by a StarTech com 3 year warranty and free lifetime technical support Features Can be used with a single computer or connected to an existing dual VGA KVM switch Easy installation using 2 industry standard UTP network cables Intuitive hotkey commands Supports auto switching between local and remote users or dedicated control USB computers are supported at the local and remote locations USB keyboard and mouse required for remote console Independently adjust video quality inclusive of Equalizer sharpness Gain brightness and RGB skew System Requirements 1x integrated KVM cable each for the local and remote computers Longer cables are available from StarTech com part numbers SVECONx PS 2 SVECONUSx USB 2xunshielded Category 5 5e 6 twisted pair UTP straight through network cable terminated at each end with RJ 45 connectors if using surface cabling OR Unshielded Category 5 5e 6 twisted pair UTP straight through network cable terminated at each end in two wall mounted outlets with two
Download Pdf Manuals
Related Search