Premier Mounts FLIP-B flat panel ceiling mount
Contents
1. 3 78 96 01 4 70 1 92 11 98 119 38 48 771 304 29 aL 1 97 50 03 470 394 295 an 119 381 100 07 74 931 9 4 100 07 2 00 a 3 90 149 86 Page 10 Installation Instructions b 4 FLIP Mount 24 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DIS PLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAM2. Softwood Cabinet Installation A NOTE 1 4 20 Tee Nut and screws are recommended when installing the FLIP mount into softwood surfaces 1 4 20 Tee Nut 1 4 20 Tee Nut Cupboard Pre drilled Hole 5 16 drill bit 1 4 20 x 5 8 Screw FLIP Mount Screwdriver _f Step 1 Use a 5 16 drill bit and drill to pre drill the tee nut pilot holes in the underside of the cupboard Step 2 After drilling the mounting holes open the cupboard door and place two 2 1 4 20 tee nuts into each hole see inset above Use a hammer to gently tap into place Step 3 Line the FLIP Mount up with the two pre drilled mounting holes Step 4 Using a screwdriver insert and tighten two 2 1 4 20 x 5 8 screws and attach the FLIP Mount to the underside of the cabinet Page 6 Installation Instructions FLIP Mount Mount Installation Wall Surface Optional l lt j ValS Electronic Stud Finder Step 1 If the location where the flat panel will be installed is acceptable use a stud finder to determine the exact center of each stud Step 2 Once a wood stud has been located mark this spot with a pencil This will be the upper mounting point if I _ I lt Wall Stud I 1 8 Drill Bit Before drilling the pilot holes line A up the mounting holes with the pencil marks and level the FLIP mount if needed Step 4 Using a 1 8 drill bit pre drill both pilot holes
3. AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELAT ING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST 5 TIMES THE WEIGHT OF THE FLAT PANEL IF NOT THE WALL STRUCTURE MUST BE RE INFORCED PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY Indicates that the power plug is to be disconnected Contact Premier Mounts with any questions from the power outlet 800 368 9700 Safety precautions must be taken at all times Warning and Caution statements It is recommended that a maximum of 5 8 plaster board be used when mounting to
4. at the marked locations Installation Instructions Wall Stud Mark FLIP Mount Step 3 Mark the lower mounting point as well once the upper mounting point has been marked Wall Stud 14 x 2 Wood Screw FLIP Mount Screw driver Using a portable drill insert and tighten two 2 14 x 2 wood screws Ay warna Do NOT over tighten the wood screws as this could cause the threads to strip out the wood inside the wall stud Page 7 FLIP Mount Attaching the Flat Panel If you chose not to use the 360 feature of the FLIP mount please insert and tighten one 1 M5 x 10mm flat head screw into any one of the four mounting point locations please see below for mounting points The M5 x 10mm flat head screw will prevent the FLIP mount from rotating 360 Ao FLIP Mount Keyhole Mounting Slot M4 x 10mm M5 x10mm Flat Head Screw see NOTE M4 x 10mm Screw Mounting Point N pS S en Te SN Beu nN _IT gt D_ Fiat Panel Re a 7 5s x N Aw Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Page 8 If you chose not to use the 360 feature of the FLIP mount please insert and tighten one 1 M5 x 10mm flat head screw into any one of the four mounting point locations please see above for mounting points The M5 x 10mm flat head screw will prevent the FLIP mount from rotating 360 Locate the mounting points that are on t
5. wooden studs Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the flat panel and or damage to the mounting surface Do not install near heater fireplace direct sunlight air conditioning or any other source of direct heat energy Failure to do so may result in damage to the flat panel and could increase the risk of fire At least two qualified people should perform the installation procedure Injury and or damage can result from dropping or mishandling the flat panel OPP PP OOO 6 QO Installation Instructions ae o ya N b 4 FLIP Mount P Parts List Congratulations on the purchase of your new Premier Mounts FLIP flat panel mount This mount is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts Z 800 368 9700 NI gt The M5 flat head screw will prevent NOTE rotating 360 Gy Ke Ke M5 x 10mm Flat Head Screw Qty 1 1 4 20 x 5 8 Combo Screw Qty 2 eG e v amp M4 x 10mm Combo Screw Qty 4 1 4 20 Tee Nut Qty 2 as PI NOTE the FLIP mount mounting plate from 14 x 2 Wood Screw Qty 2 14 x 7 8 Wood Screw Qty 2 Wall Stud Applications Under counter Applications 5 32 Allen Wrench 5 16 Dril
6. AGES INCLUD ING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original con sumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Installation Instructions Page 11
7. cD PREMIER y Wa MOUNTS The original holding company INSTALLATION INSTRUCTIONS FLIP Flip Down LCD Mount NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 800 368 9700 Fax 800 832 4888 Phone 44 0 2476 614700 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2009 9531 017 011 00 24 FLIP Mount Table of Contents Warnme Statements ciinei EE a e aeai Aaea r iai haina eiea 2 Parts EiS oeeie a A T AE EE EE E a 3 T st llation TOOS eree ana a ON EEEE Ere SE EEN ELETERE 3 ELIP Mo nt Locatioh oscri a a a a a ad 4 Hardwood Cabinet Fis tal Aine os 510 524 bin ione yy sranocentescnonaderd saddens beteareoeckdenn oa aaa E Eaa Ei z Softwood Cabinet Installati n eienen e E E E ee cnae 6 Mount Installation Wall Surface Optional scsiiscisieosscsncescocseenesesectecssceeeaieneasdesannassabeesnnessess 7 Astachine the Flat Panel a ceiessiascidsscnceetianeieiat net tadeee scat ae van E E A 8 FLIP M nt Adj stMEntS oss cei cissahaduniss que sac ineas niai enera Agseactessasastueseoens 9 Final AdjJ sStMEntS sennoina sen e EEEE EECA E TETEA EEE eatin 9 Technical SpecincationS saareen EAE AEn ree aiae SEEE 10 Warran aea a e E O A E NEER 11 Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ
8. he back of the flat panel Line up the mounting points on the flat panel with the corresponding mounting holes on the FLIP mount Loosely attach the upper two 2 M4 x 10 mounting screws Insert the screw heads into the corresponding keyhole mounting slots that are on the FLIP mount With the FLIP mount securely attached insert and tighten the two 2 lower M4 x 10 mounting screws Use a screwdriver to tighten all mounting hardware at this time Installation Instructions FLIP Mount FLIP Mount Adjustments SS Vertical Adjustment Final Adjustments The FLIP mount has pivots points that allow the mount to be easily adjusted Once the adjustments have been made the pivot points will need to be tightened Please refer to the steps below to tighten the pivot point screws Step 1 Make sure the FLIP mount has been adjusted to the determined viewing angle Step 2 Locate each pivot point Step 3 Use the 5 32 Allen wrench supplied to tighten each pivot point screw Installation Instructions 360 Rotation Adjustment Left to Right 360 Rotation Adjustment Pivot Point Tilt Adjustment Pivot Point Screw 5 32 Allen Wrench 5 32 Allen Wrench Vertical Lateral Pivot Point Adjustment Screw Pivot Point Page 9 b a 22 FLIP Mount Technical Specification All measurements are in inches mm
9. l Bit 1 8 Drill Bit Tee Nut Installation Wood Stud Installation Electronic Stud Finder Drill Hammer Tape Measure Pencil Screwdriver Installation Instructions Page 3 FLIP Mount FLIP Mount Location A wre Before drilling make sure that there is enough room to lower and raise the display For example when the display is put in the up position it should not hit the wall and should be even with the front of the cabinet A NOTE Mount placement will be primarily determined by the size of the flat panel being used A per There must be enough clearance for the FLIP mount and flat panel to be adjusted without interfering with the wall counter top surface and the overhead cupboard see diagram below Clearance Cupboard Clearance UP Position FLIP 13 a J Mount Via E S va Flat DOWN Position y Clearance Counter top When mounting the FLIP mount to the underside of a cupboard careful consideration must be taken The following steps will help in determining the placement of the FLIP mount please see diagram above Step 1 Step 2 Step 3 Step 4 Step 5 Page 4 Attach the flat panel to the FLIP mount SEE PAGE 8 Put the FLIP mount in the up position Place the FLIP mount base flush on the underside of the cupboard Slide flat panel and FLIP mount to the rear of the cupboard surface until the botto
10. m edge of the flat panel is a minimum 1 from the wall Use a pencil to mark where the two mounting holes are This will be the location where your pilot holes will be drilled Installation Instructions FLIP Mount P Hardwood Cabinet Installations A NOTE Wood screws are recommended when mounting the FLIP mount onto hardwood surfaces Cupboard FLIP Mount This distance was determined in the FLIP Mount Location section Step 1 Place the FLIP Mount base on the mounting location and mark using a pencil where the FLIP will be mounted The FLIP mount base may be used as a A NO template when marking the mount location Prior to drilling into the underside of the NOTE i ve cabinet it is strongly recommended that all items be removed from the cabinet Marking X 1 8 Drill Bit Drill N ts Qe oN Step 2 Using a 1 8 drill bit and portable drill pre drill both pilot holes at the a marked locations A Installation Instructions Page 5 b a 24 FLIP Mount Step 3 Line the FLIP Mount up with the two pre drilled mounting holes and use two 2 14 x 7 8 wood screws and secure the FLIP Mount to the underside of the cabinet using a screwdriver A WARNING Do NOT over tighten the wood screws as this could cause the threads to strip out the wood inside the cabinet enclosure 14 x 7 8 Wood Screw FLIP Mount ce Screwdriver
Download Pdf Manuals
Related Search