Premier Mounts UNI-PDSB project mount
Contents
1. Throw Distance Calculation Please review the Operator s Manual that came packaged with your projector before attaching the upper mounting NOTE bracket The correct throw distance the distance from the projector to the screen must be determined prior to mounting the projector Yoo Step 1 Refer to the projectors Users Manual to Calculations determine the distance from the lens to the X Manufacturers recommended front of the screen throw distance Step 2 Measure the distance from the front of the Z Distance from wall to face of lens to the center of the PDS PLUS see whiteboard screen Front Lens diagram Front Mounted Len ont Mounted Leng g Front Lens Throw Distance For front mounted lenses add distance Y X Y Z to distance listed in projector Users Manual Rear Mounted Lens Rear Lens Throw Distance For rear mounted lenses subtract disance Y from X Y Z the distance listed Step 4 Use a tape measure to mark the appropriate distance on the UNI STA UNI EXT This will be where the center of the mounting bracket will be located Rear Lens If installing UNI EXT please refer to Ne eee A Page 10 before continuing Page 8 Installation Instructions UNI STA UNI EXT Upper Mounting Bracket Installation Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Insert the inner slide plate into the projector arm Determine which adjustment slot will be best for the projec2. Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DIS PLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUD ING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original con sumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIV
3. MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACH MENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE PROJECTOR IF NOT THE STRUCTURE MUST BE REINFORCED THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 75LBS PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the projector If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting drilling into an electrical line may cause serious injury Make sure there are no water line
4. location for the bottom rail on the wall Ground j plate Page 4 Installation Instructions b 4 UNI STA UNI EXT 24 Wood Stud Installation A Do NOT over tighten lag bolts when attaching the mount to the wall Improper installation may result in personal injury or damage to property WARNING 8 property STOP DEAD CENTER MUST BE LOCATED ON THE STUD FOR CORRECT AND SAFE INSTALLATION Stud finder R Step 1 Use an electronic stud finder Step 2 Use a pencil to mark the first Step 3 Use the level to make sure commercially available to mounting hole just above the wall plate is level from locate the center of the stud your height mark from top to bottom After that is in the wall page 4 determining the desired viewing height place the Lag Bolt and wall plate over the first hole Flat Washer and use a pencil to mark the rest of the holes Drill Marking Wall Plate Covers Socket Step 4 Once the holes have been Step 5 After the pilot holes have marked use a 1 4 drill bit been drilled use four 4 and portable drill to drill the 5 16 x 3 lag bolts and four pilot holes 4 flat washers to mount the wall plate to the wooden stud Use a 1 2 socket and socket wrench to finish this step Step 6 Insert and gently tap the wall plate covers into place Completed Installation Installation Instructions Page 5 b 4 CAA Solid Surface Installation A NOTE Concrete drill b
5. 2 NPT or CLS sold separately Step 1 Thread in CLS or any 1 1 2 NPT until securely fastened Step 2 Thread in one 1 M6 x 6mm set screw Step 3 Use an M3 security wrench to tighten the M6 set screw included in the PDS PLUS hardware Upper Mounting Bracket M6 Set Screw M3 Security Wrench Installation Instructions Page 11 gt 2 UNI STA UNI EXT Technical Specifications All measurements are in inches mm 26 15 664 24 00 610 3156 802 T 16 00 406 9 60 244 10 69 272 10 69 272 E YJ 26 04 661 OPTIONAL EXTENSION Ee T me MAXIMUM DISTANCE FROM WALL MINIMUM DISTANCE FROM WALL La 070 696 ee 7 00 cree eae Page 12 Installation Instructions D UNI STA UNI EXT 24 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered
6. ES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Installation Instructions Page 13
7. be easiest to pre wire all cables down the arm or extension at this time see Page 11 Security Wrench M5 x 12mm Security Screw Electronic Components Electronic Components Door Door Step 1 Open the storage door that is located on the side of Step 4 Close the storage door and secure using two the wall plate 2 1 upper and 1 lower M5 x 12mm security Step 2 Place the electronic components inside the storage head screws Tighten using a security wrench enclosure Repeat this process for the other side as well Step 3 Make all electronic connections at this time Attaching the Projector Arm Mounting Hook Cutout Mounting Hooks Wall Plate Projector Arm Step 1 Locate the mounting hook cutout on the top of the wall plate Step 2 Tilt the arm slightly and gently insert the mounting hooks into the mounting hook cutouts Step 3 Slowly lower and let the projector arm rest against the wall plate Installation Instructions Page 7 gt rH UNI STA UNI EXT A MAKE SURE THE PROJECTOR ARM IS FULLY SEATED BEFORE RELEASING THE UNIT WARNING Lock Mounting Point MS x 12mm Security Head Screw Screwdriver Security Wrench Step 4 Locate the two 2 lock mounting points on the projector arm These two points will be aligned with the lock mounting points on the wall plate Step 5 Using a security wrench insert and tighten two 2 M5 x 12mm security head screws A DO NOT OVERTIGHTEN THE SCREWS WARNING
8. cD PREMIER Cad MOUNTS The original holding company INSTALLATION INSTRUCTIONS UNI STA UNI EXT Universal Short Throw Projector Arm NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House a oe ee ea USA Shilton Industrial Estate Von es Shilton Coventry England CV79JY Phone 800 368 9700 Fae c00 839 Auee Phone 44 0 2476 614700 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2009 9530 010 001 00 UNI STA UNI EXT Wating Statements osoorssnieiiriseiiiii eii E EERE EEE E EA eit R E ict at i EER EER 2 Parts List sessusessssa Installation Tools Determining the Installation Height Wood Stud Installation Solid Surface Installation Utilizing the Storage Feature Attaching the Projector Arm Throw Distance Calculation Upper Mounting Bracket Installation Extension Arm Installation Base Box Installation Cable Management Set Screw Installation Optional Technical Specifications Warranty Warning Statements 9 YP PSPOoCS 6 O PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COM PLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER
9. er 1 4 Drill Bit Electronic Stud Finder 1 2 Socket and Socket Wrench 3 8 Masonry Drill Bit Installation Instructions Page 3 gt 4 24 UNI STA UNI EXT Determining the Installation Height In order to determine the installation height and throw distance the PDS PLUS projector bracket must be mounted to the A NOTE projector Please refer to the PDS PLUS Installation Instructions prior to performing the following steps A NOTE Refer to the projectors User s Manual to determine the offset of the projector lens to the top of the screen whiteboard Projector Step 1 Measure distance from center of lens to the top of the PDS PLUS bracket Step 2 Add the distance from the ground to the top of the screen A the recommended offset from the projector manual B the measurement from Step 1 C and then add 1 5 Example A B C 1 5 Step 3 Measure the calculated distance from the top edge of the viewable area of the screen whiteboard and mark the wall This mark will represent the lower edge of the wall plate Mark Set 15 Top of Screen F Legend A Distance from ground to the top of the screen whiteboard viewable area B Manufacturers recommended offset A measurement This measurement will be listed in the Users Manual C Center of the lens to the top of the PDS PLUS bracket Add 1 5 to the calculated total This total distance will be the
10. he mounting slots on the UNI STA Step 5 Using a screwdriver insert and tighten two 2 M6 x 12mm security head screws 1 4 flat washers and 1 4 nylon spacers Step 6 Attach the PDS PLUS see page 10 Base Box Installation Please review the Operator s Manual that A came packaged with the PDS PLUS before attaching the PDS PLUS to the upper mounting bracket Projector Mount M6 x 12mm Screws Security Wrench Base Box Step 1 Raise the base box projector mount to the upper mounting bracket Step 2 Align the two 2 one each side mounting holes Step 3 Using a screwdriver security wrench insert and tighten two 2 M6 x 12mm security head screws Do not over tighten the screws Step 4 Attach the projector to the base box referring to the PDS PLUS Installation Instructions for final adjustments Page 10 Installation Instructions gt 4 UNI STA UNI EXT 24 Cable Management UNI STA me amp Electronic Components Electronic Components UNI EXT aa Cables Electronic Components A Cable Opening Cable Opening Projector Hook Upss Cables oO 0 ooo re lt OSC Cable Opening Projector Hook Ups Step 1 The cable access holes are located at the end of the short throw mount and on the wall plate Step 2 Route the cables through one end of the UNI STA UNI EXT and out the other end Set Screw Installation Optional The M6 set screw will be used in conjunction with any standard 1 1
11. its are commercially available Marking Step 1 Place the wall plate against the wall and use a level to make sure the wall plate is Step 3 Usea3 8 drill bit to drill the mounting holes where the marks were made with a level from top to bottom pencil Step 2 Use a pencil to mark the location of the mounting holes Nut and Washer Seated Wedge Anchor Socket Wall Plate Wall Plate Step 7 Place the flat washer and nut onto the wedge anchor and tighten using a socket and socket wrench Do not overtighten Step 8 Insert and gently tap the wall plate covers into place Step 6 Place the wall plate over the wedge anchors once the wedge anchors have been correctly inserted into the mounting surface Page 6 Drill 3 8 Drill Bit UNI STA UNI EXT Hammer ee Wedge Anchor Step 4 Step 5 Once the holes have been drilled place the concrete wedge anchors into the hole Using a hammer gently tap into place Once the wedge anchors have been inserted into the mounting holes remove the nut and flat washer from the wedge anchor Wall Plate Covers Completed Installation Installation Instructions gt 4 UNI STA UNI EXT 24 Utilizing the Storage Feature The storage feature may be used to store electronic components There is an accessible door on each side of the storage enclosure It may be securely held shut with the use of four 4 M5 x 12mm security head screws It may
12. s inside the wall where the mount is to be located Cutting drilling into a water line may cause severe water damage to the mounting surface This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Installation Instructions gt 4 UNI STA UNI EXT 24 Parts List This mount is shipped with all proper installation hardware and components Make sure that none of these parts are A missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 Wz Extension Hardware Pack M6 x 12mm Security Qty 2 1 4 Flat Washer Qty 2 1 4 Nylon Spacer Extension Arm Optional Qty 1 Qty 2 included with the UNI EXT HE O 2 Non Security Qty 1 Security Qty 1 Upper Mounting Bracket Inner Slide Plate Qty 1 5 16 x 3 Lag 5 16 Flat M6 Set Screws Qty 1 Bolts Qty 4 Washers Qty 4 M5 x 12mm Security Head M6 x 12mm Security 3 8 Concrete Wedge Back Plate Security Wrenches Screws Qty 11 Head Screws Qty 4 Anchors Qty 4 Covers Qty 2 PDS PLUS Hardware Pack PDS PLUS Projector Mount P Phillips Screwdriv
13. tor placement Raise the upper mounting bracket into position Align the mounting holes of the upper projector plate with the mounting holes of the inner slide plate Secure and finger tighten two 2 M6 x 12mm security head screws Once the correct throw distance has been determined use the security wrench supplied to tighten the mounting screws Do not overtighten the screws Installation Instructions Projector Arm Adjustment Slot Inner Slide Plate Upper Mounting Bracket M6 x 12mm Security Screw Calculated Throw Distance Security Wrench Page 9 gt 4 CA UNI STA UNI EXT Extension Arm Installation Optional Please see the Operator s Manual to determine the correct throw distance the distance from the projector to the screen A NOTE must be determined prior to mounting the projector A If the extension arm was purchased at a later date the end cover must be removed prior to installing the extension arm WARNING UNI STA 1 4 Flat Security Screw Security Wrench Upper Mounting Bracket Extension Arm Step 1 Slide the extension arm into the open end of the UNI STA the front of the mount Step 2 Attach the upper mounting bracket directly to the extension using two 2 M6 x 12mm set screws see page 8 Step 3 Adjust length so that the center of the upper mounting bracket matches the throw distance calibration Step 4 Line up the mounting holes on the extension arm with t
Download Pdf Manuals
Related Search