Premier Mounts RTM-L flat panel wall mount
Contents
1. PREMIER MOUNTS The original holding company INSTALLATION INSTRUCTIONS Rotary Tilt Mount Model RTM L AUSTRALIA NEW ZEALAND OCEANIA NORTH AMERICA EUROPE DISTRIBUTOR 3130 East Miraloma Avenue Swallow House P O Box 295 d USA Shilton Industrial Estate Mordialloc Victoria 3195 U oT Shilton Coventry England CV79JY Australia Phone 800 368 9700 Fax 800 832 4888 Phone 444 0 2476 614700 Phone 039586 6330 Fax 44 0 2476 614710 WWW premiermounts com au Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2008 9531 009 011 03 Al P RTM L Marna SU e S E 2 Parts B MER m 9 118 16 11 518 18 54 ai AA AA AA AA EEE AAA AA NAA AAA AAA AAA AAA aaa 3 Depi AMAT 6 7 Universal Mounting Bracket Installation 9 10 idc un AM oe 10 CODE 11 Technical equ o 18 8 18 11 cH EUM HENRI n ISO E MM MALIA 12 IY waa d gnc 13 Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY2. L a es Installation Instructions RTML CC YO A Note The nylon spacers may be stacked to achieve proper spacing 1 4 Nylon spacers 9 16 Nylon spacers large Oty 8 Oty 8 1 2 Nylon spacers large Nylon sleeves Qty 12 Qty 8 5 16 Flat washers metal Qty 8 1 Nylon Spacers Qty 8 1 O3 1 4 Nylon spacers small Oty 8 Installation Instructions Page 5 b 24 oA RTM L Thread Depth Indicator 1 Insert the thread depth indicator supplied through the thread inserts found the back of the flat panel to make sure the inserts measure the same full depth and mark it Figure 1 2 Locate the correct diameter screw for the thread insert Compare your marking to the screws supplied 3 If your selected screw is longer than the marking on the thread depth indicator DO NOT USE this screw 4 The screw length must not bypass the marking Select another screw size Figure 2 and 3 until you find one that comes closest to your mark without going past e zu SEU Inverted Flat Panel Display Marking the J Depth 7 Thread Insert Thread Depth Indicator 221777277717777777117220 B screw Marking Thread Depth Thread Depth Indicator Indicator Page 6 Installation Instructions RTM L YA Mount Installation The installation instructions that are contained in this manual refer only to the RTM L The installation instructions AN Note for the va
3. DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE DISPLAY IF NOT THE SURFACE STRUCTURE MUST BE REINFORCED THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 160LBS PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the display If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder 18 recommended This product is intended for indoor use only Use of this product ou
4. BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LA BOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE QUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original con sumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 E Miraloma Avenue Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Installation Instructions Page 13
5. e handle Page 10 Installation Instructions RTM L PA Optional Configurations PSD TS Technical Specifications All measurements are in inches mm 7 854 199 49 17 41 449 21 10 00 ENS F Installation Instructions Page 11 4 28 RTM L Lock It Security Hardware Pack The RTM L is shipped with a safety knurl knob already installed If the user decides to incorporate the optional security hardware the following steps will show the user how to effectively remove the safety knurl knob and install the optional Lock It M hardware kit security head screw prior to completing assembly will not allow the RTM L to function properly 4 12mm Security Head Screw Security Allen Wrench Qty 1 and Lock Washers Qty 2 Qty 1 The M6 security head screw will be installed after the RTM L has been fully assembled Installation of the M6 Note 6 Security Head Screw and Lock Washers Safety Knurl Knob Universal Bracket Step 2 Place the two lock washers onto the Step 1 M6 x 12mm security head screw Remove the RTM L from the packaging Place the M6 x 12mm security head and remove the existing safety knurl knob screw onto the security Allen wrench Remove the universal bracket bar and insert into mounting point Safety Knurl Knob M6 Security Head Screw and Lock Washers Step 4 Once the M6 security head screw has been i
6. lips head screws located on the side of the mounting block to prevent Locking Screws 5 the mount from rotating Installation Instructions Page 9 b 4 RTM L Display Orientation The RTM L will allow the user to adjust the display a full 360 BEFORE ROTATING THE RTM L MAKE SURE THAT THE M6 KNURL KNOB IS SECURELY FASTENED A WARNING TO THE RTM L ALSO PLEASE MAKE SURE YOU ALLOW ENOUGH CABLE AND WIRE CLEARANCE FOR FULL ROTATION 1 To adjust the RTM L rotate the display either clockwise or counter clockwise 2 Tighten the two Phillips head locking screws Tilt Positioning The RTM L is shipped with the hand crank in the storage position The hand crank must be removed in order for the RTM L to be adjusted After the adjustments have been made return the hand crank to the storage position If the hand crank is not returned to the storage position it may cause damage to the unit or other equipment Please return the hand crank to the storage position after operation E IE 1 Rotate the crank handle to tilt the RTM L Down Clockwise Up Counter Clockwise The RTM L has the ability to tilt 10 down The RTM L has the ability to tilt 35 up Once the position has been locked down use an Allen wrench to take off the crank handle 2 Once the crank handle has been removed re attach the crank handle but in the opposite direction from what it was This is the storage position for th
7. nstalled re insert the safety knurl knob Installation completed This will prevent the display from being removed from the RTM L as sembly Step 3 Once inserted into the mounting point fully tighten into place using the security Allen wrench Page 12 Installation Instructions dA RTM L PA Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty 18 valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED IN CLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR POSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING
8. nting points the Griplate flat side must be facing up For the two lower mounting points the Griplate flat side must be facing down 3 At this time center the universal bracket bar and tighten the set screws that are located on the universal brackets M5 M8 Universal Mounting Brackets Set Screw GriplateTM Universal Bracket Bar GriplateTM A WARNING IT WILL TAKE TWO PEOPLE TO COMPLETE THE NEXT INSTALLATION STEP 1 WARNING THE CONGFIGURATION THAT THE UNIVERSAL MOUNTING BRACKETS ARE IN ABOVE MUST RE MAIN THE SAME ANY DEVIATION FROM THE LAYOUT ABOVE COULD AFFECT THE OPERATION OF THE MOUNT Page 8 Installation Instructions 4 RTM L Dad Lower the universal bracket bar and display into the cradle as to the left et bar must rest inside the nylon sleeve If seated improperly the operation of the RTM S will be hindered and the nylon sleeve will become damaged The circular portion of the universal brack A Note Nylon Sleeve Knurl Knob Mounting Points a knurl knob may be placed in ei ther mounting hole M6 x 12mm Security Head and M6 Lock Washer Mounting Points a security screw may be placed in either mounting hole 7 Insert an M6 knurl knob into the knurl knob mounting point and tighten 8 OPTIONAL Insert a M6 x 12mm security screw and MO lock washer into the mounting point and tighten using the M5 Allen wrench supplied 9 OPTIONAL Tighten the two 2 Phil
9. rious bases that are used with the RTM L will be included with those products A Note Prior to installing the RTM L the mounting configuration must already be assembled base support poles etc Mounting Block Set Screws Cradle Support Poles MO L Slide the mounting 2 To secure the mounting block to the support poles tighten the block over and down four set screws located on each side of the mounting block the support poles using the 5 32 Allen wrench supplied Installation Instructions Page 7 gt 4 RTM L Universal Mounting Bracket Assembly l Place the universal bracket bar and the universal brackets on a flat surface 2 Slide the universal brackets onto the universal bracket bar as shown below with the set screws facing up At this time do not tighten the set screws that are located on the universal bracket If you havean un even mounting surface or a recessed mounting point place the appropriately sized nylon washer Note between the display and the universal mounting brackets page 5 3 Place the display on a soft flat surface face down Next place the universal bracket assembly on the back of the display with the universal brackets resting directly over the display mounting points 4 Once the desired position has been determined place the Griplate washers over each mounting point and secure them using the appropriate hardware see Page 4 and 5 Note For the two upper mou
10. tdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com e o9 Page 2 Installation Instructions 4 I RTM L 24 Parts List This wall mount is shipped with all proper installation hardware and components Make sure that none of these parts Note are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 NS niversal Mounting Brackets Qty 2 Rotary Tilt Mount Qty 1 tj GriplateTM Qty 8 M6 Knurl Knob Hand Crank Qty 1 Qty 1 Installation Tools Phillips Head Screw Driver Soft Material Blanket Pencil Tape Measure Thread Depth Indicator Supplied Level Supplied 5 32 Allen Wrench Supplied Installation Instructions Page 3 5 x25 M5 50 Mo x 16 Page 4 Qty 9 Mo x 20 Mo x 45 M8 x 20 25 Qty 8 M8 x 30 x45 M8 x 70 RIM L Qty 8
Download Pdf Manuals
Related Search