Home

TP-LINK TL-WDR3600 router

1. Figure 4 7 WAN BigPond Cable User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive Auth Server Enter the authenticating server IP address or host name Auth Domain Type in the domain suffix server name based on your location e g NSW ACT nsw bigpond net au VIC TAS WA SA NT vic bigpond net au QLD qld bigpond net au MTU Size The normal MTU Maximum Transmission Unit value for most Ethernet networks is 1500 Bytes It is not recommended that you change the default MTU Size unless required by your ISP Connect on Demand In this mode the Internet connection can be terminated automatically after a specified inactivity period Max Idle Time and be re established when you attempt to access the Internet again If you want your Internet connection keeps active all the time please enter O in the Max Idle Time field Otherwise enter the number of minutes you want to have elapsed before your Internet access disconnects Connect Automatically The connection can be re established automatically when it was down Connect Manually You can click the Connect Disconnect button to connect disconnect 26 TL WDR3600 EA AAEE ETT Meier lolimacelenccys immediately This mode also supports the Max Idle Time function as Connect on Demand mode The Internet connection can be disconnected automatically after a specified inactivity period and re es
2. WPA WPA2 Personal Recommended Version Automatic Recommended v Encryption TKIP v PSK Password 12345670 fou can enter ASCII characters between 8 and 63 or Hexadecimal characters between 8 and 64 Group Key Update Period 0 Seconds Keep it default if you are not sure minimum is 30 0 means no update We do not recommend using the TKIP encryption ifthe device operates in 802 11n mode due to the fact that TKIP is not supported by 802 11n specification Figure 4 21 WPA WPA2 Personal e PSK Password You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters The default password is the same with the default PIN code which is labeled on the bottom of the Router or can be found in Figure 4 16 e Group Key Update Period Specify the group key update interval in seconds The value should be 30 or above Enter 0 to disable the update WPA WPA2 Enterprise It s based on Radius Server e Version you can choose the version of the WPA security on the drop down list The default setting is Automatic which can select WPA Wi Fi Protected Access or WPA2 WPA version 2 automatically based on the wireless station s capability and request e Encryption You can select either Automatic or TKIP or AES cf Note If you check the WPA WPA2 Enterprise radio button and choose TKIP encryption you will find a notice in red as shown in Figure 4 22 WPAWPA2 Enterprise V
3. E Note The current configuration will be covered with the uploading configuration file Wrong process will lead the device unmanaged The restoring process lasts for 20 seconds and the Router will restart automatically then Keep the power of the Router on during the process in case of any damage 109 TL WDR3600 EA AAEE a Meier lolimacelenccys 4 19 6 Reboot Choose menu System Tools Reboot and then you can click the Reboot button to reboot the Router via the next screen Reboot Click this button to rebootthe device Figure 4 115 Reboot the Router Some settings of the Router will take effect only after rebooting which include Change the LAN IP Address system will reboot automatically Change the DHCP Settings Change the Wireless configurations Change the Web Management Port Upgrade the firmware of the Router system will reboot automatically Restore the Router s settings to factory defaults system will reboot automatically Vv Vv Y Y V VY WV Update the configuration with the file system will reboot automatically 4 19 7 Password Choose menu System Tools Password and then you can change the factory default user name and password of the Router in the next screen as shown in Figure 4 116 Password Old User Name Old Password New User Name New Password Contirm New Password Figure 4 116 Password It is strongly recommended that you should change the
4. PSK Password O Enable TP LINK_2 4GHz_13098E Also called the SSID United States l Y 2 4GHz Mbgn mixed Auto v Auto E Disable Security Enable SecuritaWPA PSKMWPA2 PSK 12345670 fou can enter ASCII characters between 8 and 63 or Hexadecimal characters between 8 and 64 No Change Figure 3 12 Quick Setup Wireless gt Wireless Radio Displays whether the wireless function is enabled or not gt Wireless Network Name Also called the SSID Service Set Identification Enter a value of up to 32 characters The same name must be assigned to all wireless devices in your network The default SSID is set to be TP LINK_2 4GHz_XXXXXX This value is case sensitive For example TEST is NOT the same as fest gt Region Select your region from the drop down list This field specifies the region where the wireless function of the Router can be used It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field If your country or region is not listed please contact your local government agency for assistance Cf Note Limited by local law regulations version for North America does not have region selection option gt Band This field displayed the operating frequency being configured gt Mode This field determines the wireless mode which the Router works on 15 TL WDR3600 BCU EN ETT M
5. TP LINK User Guide TL WDR3600 N600 Wireless Dual Band Gigabit Router Rev 1 0 0 1910010674 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK isa registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2012 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT HE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measur
6. screen shown in Figure 4 16 It is also labeled on the bottom of the Router Step 2 The Wi Fi Protected Setup LED flashes for two minutes during the Wi Fi Protected Setup process Step 3 When the WPS LED is on the client device has successfully connected to the Router Step 4 Refer back to your client device or its documentation for further instructions cs Note 1 The WPS LED on the Router will light green for five minutes if the device has been successfully added to the network 2 The WPS function cannot be configured if the Wireless Function of the Router is disabled Please make sure the Wireless Function is enabled before configuring the WPS 4 6 3 Wireless Security Choose menu Wireless 2 4GHz Wireless Security you can configure the security settings of your wireless network There are five wireless security modes supported by the Router WPA Personal WPA2 Personal WPA Enterprise WPA2 Enterprise and WEP 38 TL WDR3600 BCU TUE a RCIE o vi Wireless Security Disable Security WPA WPA2 Personal Recommended Version Autamatic Recommended Y Encryption AES 7 I vi PSK Password 12345670 fou can enter ASCII characters between 8 and 63 or Hexadecimal characters between 8 and 64 Group Key Update Period Oo Seconds Keep it default if you are not sure minimum is 30 0 means no update O WPA WPA2 Enterprise Version Automatic v Encry
7. Allow the packets specified by any enabled access control policy to pass through the Router Deny the packets specified by any enabled access control policy to pass through the Router Save ID Rule Name Schedule Enable Setup Wizard Add New Current No 1 Page Figure 4 77 Access Control Rule Management Enable Internet Access Control Select the check box to enable the Internet Access Control function so the Default Filter Policy can take effect Rule Name Here displays the name of the rule and this name is unique Host Here displays the host selected in the corresponding rule Target Here displays the target selected in the corresponding rule Schedule Here displays the schedule selected in the corresponding rule Enable Here displays the status of the rule enabled or not Check this option to enable a specific entry Modify Here you can edit or delete an existing rule Setup Wizard Click the Setup Wizard button to create a new rule entry Add New Click the Add New button to add a new rule entry Enable All Click the Enable All button to enable all the rules in the list Disable All Click the Disable All button to disable all the rules in the list Delete All Click the Delete All button to delete all the entries in the table Move You can change the entry s order as desired Enter in the first box the ID number of the entry you want to move and in the second box another ID number and
8. TL WDR3600 EA AAEE a ella o vi gt Save Log Click to save all the logs in a txt file gt Mail Log Click to send an email of current logs manually according to the address and validation information set in Mail Settings gt Clear Log All the logs will be deleted from the Router permanently not just from the page Click the Next button to go to the next page or click the Previous button to return to the previous page 4 19 9 Statistics Choose menu System Tools Statistics and then you can view the statistics of the Router including total traffic and current traffic of the last Packets Statistic Interval Statistics Current Statistics Status Disabled Packets Statistics Interval 5 60 10 Seconds Auto refresh Sorted Rules Sorted by Current Bytes w Reset All Delete All Total Current Modify IF Address WAC Address Packets Bytes Packets Bytes ICMP Tx UDP Tx SYN Tx The current list is empty entries per page Current No page Figure 4 119 Statistics gt Current Statistics Status Enable or Disable The default value is disabled To enable it click the Enable button If it is disabled the function of DoS protection in Security settings will be disabled gt Packets Statistics Interval 5 60 The default value is 10 Select a value between 5 and 60 seconds in the drop down list The Packets Statistic interval indicates the time section of the packets statistic gt Sorted Rules Ch
9. Advanced Security Packets Statistics Interval 5 60 Seconds DoS Protection Disable Enable Enable IEMmMP FLOGO Attack Filtering ICMP FLOOD Packets Threshold 5 3600 so Packets s Enable JOP FLOOD Filtering UDP FLOOD Packets Threshold 5 3600 soo Packets s Enable TOP SYM FLOOD Attack Filtering TCP SYN FLOOD Packets Threshold 5 3600 so Packetsls Ignore Ping Packet From WAN Port Forbid Pina Packet From LAM Por Blocked DoS Host List Figure 4 70 Advanced Security gt Packets Statistics Interval 5 60 The default value is 10 Select a value between 5 and 60 seconds from the drop down list The Packets Statistics Interval value indicates the time section of the packets statistics The result of the statistics is used for analysis by SYN Flood UDP Flood and ICMP Flood ff TL WDR3600 MYT ENa Meier lolimacelenccys gt DoS Protection Denial of Service protection Check the Enable or Disable button to enable or disable the DoS protection function Only when it is enabled will the flood filters be enabled Note Dos Protection will take effect only when the Traffic Statistics in System Tool Traffic Statistics is enabled gt Enable ICMP FLOOD Attack Filtering Enable or Disable the ICMP FLOOD Attack Filtering gt ICMP FLOOD Packets Threshold 5 3600 The default value is 50 Enter a value between 5 3600 When the current ICMP FLOOD Packets number is beyond the s
10. Average Pms C Documents and Settings english Figure 3 1 Success result of Ping command gt Ifthe result displayed is similar to Figure 3 2 it means the connection between your PC and the Router failed TL WDR3600 BCU TUE a clio vi ci C WINDOWS system3 cmd exe Microsoft Windows AP Version 5 1 2600 CCo Copyright 19785 26681 Microsoft Corp C Documents and Settings english ping 192 168 9 1 Pinging 192 168 60 1 with 32 bytes of data host unreachable host unreachable host unreachable Destination host unreachable Ping statistics for 192 168 6 1 Packets Sent 4 Received A Lost A O loss gt C Documents and Settings english Figure 3 2 Failure result of Ping command Please check the connection following these steps 1 Is the connection between your PC and the Router correct Cf Note The 1 2 3 4 LEDs of Ethernet ports which you link to on the Router and LEDs on your PC s adapter should be lit 2 Is the TCP IP configuration for your PC correct fe Note If the Router s IP address is 192 168 0 1 your PC s IP address must be within the range of 192 168 0 2 192 168 0 254 3 Is the default LAN IP of the Router correct E Note If the LAN IP of the modem connected with your router is 192 168 0 x the default LAN IP of the Router will automatically switch from 192 168 0 1 to 192 168 1 1 to avoid IP conflict Therefore in order to verify the network connection between your PC an
11. Firmware Version 3 13 17 Build 120508 Rel 458584n Hardware Version WORG3600 v1 00000000 Figure 4 112 Firmware Upgrade gt Firmware Version Displays the current firmware version gt Hardware Version Displays the current hardware version The hardware version of the upgrade file must accord with the Router s current hardware version To upgrade the Router s firmware follow these instructions below 1 Download a most recent firmware upgrade file from our website www tp link com 2 Enter or select the path name where you save the downloaded file on the computer into the File Name blank 3 Click the Upgrade button 4 The Router will reboot while the upgrading has been finished Note 1 New firmware versions are posted at http www tp link com and can be downloaded for free There is no need to upgrade the firmware unless the new firmware has a new feature you want to use However when experiencing problems caused by the Router rather than the configuration you can try to upgrade the firmware 2 When you upgrade the Router s firmware you may lose its current configurations so before upgrading the firmware please write down some of your customized settings to avoid losing important settings 3 Do not turn off the Router or press the Reset button while the firmware is being upgraded Loss of power during the upgrade could damage the Router 4 The firmware version must correspond to the hardware 5 The upgr
12. Pp PO PO PO PO The time schedule can be setin Access Control schedule Status Enabled we Figure 4 74 Add or Modify Parental Control Entry gt Parental Control Check Enable if you want this function to take effect otherwise check Disable gt MAC Address of Parental PC In this field enter the MAC address of the controlling PC or you can make use of the Copy To Above button below 81 6 T TL WDR3600 Bye EAEE Sy late Rel Ade ti MAC Address of Your PC This field displays the MAC address of the PC that is managing this Router If the MAC Address of your adapter is registered you can click the Copy To Above bution to fill this address to the MAC Address of Parental PC field above Website Description Description of the allowed website for the PC controlled Schedule The time period allowed for the PC controlled to access the Internet For detailed information please go to Access Control Schedule Enable Check this option to enable a specific entry Modify Here you can edit or delete an existing entry Enter the MAC address of the PC e g 00 11 22 33 44 AA you d like to control in the MAC Address of Child PC field or you can choose the MAC address from the All Address in Current LAN drop down list Give a description e g Allow Google for the website allowed to be accessed in the Website Description field Enter the allowed domain name of the website either the ful
13. TL WDR3600 BCT BITE TRF a RIEL o vi Click the Next button to go to the next page or click the Previous button to return to the previous page Add or Modify a Host Entry Mode IF Address w LAN IF Address 192 168 0 1 1192 168 0 23 Figure 4 84 Add or Modify a Host Entry Add or Modify a Host Entry Mode MAC Address Host Description MAC Address 00 11 22 33 44 AA Figure 4 85 Add or Modify a Host Entry For example If you desire to restrict the internet activities of host with MAC address 00 11 22 33 44 AA you should first follow the settings below 1 Click Add New button in Figure 4 83 to enter the Add or Modify a Host Entry page 2 In Mode field select MAC Address from the drop down list 3 In Host Description field create a unique description for the host e g Host_1 4 In MAC Address field enter 00 11 22 33 44 AA 5 Click Save to complete the settings Then you will go back to the Host Settings page and see the following list ID Host Description information Modify 1 Host MAC O0 11 22 35 44 44 Edit Delete 4 14 3 Target Choose menu Access Control Target and then you can view and set a Target list in the screen as shown in Figure 4 86 The target list is necessary for the Access Control Rule 90 TL WDR3600 A AAEE a Meier lolimacelenccys Target Settings ID Target Description Information Modify 1 Target 1 192 168 0 2 192 168 0 2 32 1TCF Edit Delete Add
14. 00 Edit Delete Add Mew Delete All Page Figure 4 89 Schedule Settings gt Schedule Description Here displays the description of the schedule and this description is unique gt Day Here displays the day s in a week gt Time Here displays the time period in a day gt Modify Here you can edit or delete an existing schedule To add a new schedule follow the steps below 1 Click Add New button shown in Figure 4 89 and the next screen will pop up as shown in Figure 4 90 2 In Schedule Description field create a unique description for the schedule e g Schedule_1 3 In Day field select the day or days you need 4 In Time field you can select all day 24 hours or you may enter the Start Time and Stop Time in the corresponding field 5 Click Save to complete the settings Click the Delete All button to delete all the entries in the table Click the Next button to go to the next page or click the Previous button to return to the previous page 93 TL WDR3600 MCU eee BIUE a elit Advance Schedule Settings Mote The Schedule is based on the time ofthe Router AA Schedule Description Day Time Start Time Everday Select Days hon Tue Wed Thu Fri Sat sun all day 24 hours Stop Time Figure 4 90 Advanced Schedule Settings For example If you desire to restrict the internet activities of host with MAC address 00 11 22 33 44 AA to access www google com only
15. 1 000 RTS Threshold 2346 1 2348 Fragmentation Threshold 2346 256 2346 DTIM Interval 1 1 15 Enable Whim Enable Short Gl C Enable AP Isolation Save Figure 4 41 Wireless Advanced Transmit Power Here you can specify the transmit power of Router You can select High Middle or Low which you would like High is the default setting and is recommended Beacon Interval Enter a value between 20 1000 milliseconds for Beacon Interval here The beacons are the packets sent by the Router to synchronize a wireless network Beacon Interval value determines the time interval of the beacons The default value is 100 RTS Threshold Here you can specify the RTS Request to Send Threshold If the packet is larger than the specified RTS Threshold size the Router will send RTS frames to a particular receiving station and negotiate the sending of a data frame The default value is 2346 Fragmentation Threshold This value is the maximum size determining whether packets will be fragmented Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets 2346 is the default setting and is recommended DTIM Interval This value determines the interval of the Delivery Traffic Indication Message DTIM A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages When the Router has buffered broadcast or multicast mes
16. Default gateway Use the following DNS server addresses Preferred DHS server Alternate DNS server Figure B 3 122 TL WDR3600 BCC BITE ETT Meier lolimacelenccys Appendix C Specifications IEEE 802 11n IEEE 802 119 IEEE 802 11b IEEE 802 11a IEEE 802 11e IEEE 802 111 IEEE 802 1X IEEE 802 3X IEEE 802 3 IEEE 802 3u IEEE 802 3ab TCP IP PPPoE DHCP ICMP NAT SNTP 1 10 100 1000M Auto Negotiation Internet RJ45 port Ports 4 10 100 1000M Auto Negotiation Ethernet RJ45 ports supporting Auto MDI MDIX 2 USB ports supporting storage FTP Media Print Server 10BASE T UTP category 3 4 5 cable maximum 100m ElA TIA 568 1000 STP maximum 100m 100BASE TX UTP category 5 5e cable maximum 100m Cabling Type l EIA TIA 568 1000 STP maximum 100m 1000BASE TX UTP category 5 5e cable maximum 100m EIA TIA 568 1000 STP maximum 100m Power System Wireless 2 4GHz Wireless 5GHz Ethernet 1 4 LEDs Internet WPS Safety amp Emissions FCC CE Frequency Band 2 4GHz 5GHz 11b 1 2 5 5 11 Mbps Radio Data Rate 11a g 6 9 12 18 24 36 48 54Mbps 11n up to 300Mbps 2 4GHz 300Mbps 5GHz Frequency Expansion DSSS Direct Sequence Spread Spectrum verre 11 n g a QPSK BPSK 16 QAM 64 QAM for OFDM 11b CCK DQ PSK DBPSK WEP WPA WPA2 WPA2 PSK WPA PSK 1M 98dBm 8 PER 11M 92dBm 8 PER 6M 93dBm 10 PER 54M 75dBm 10 PER 65M 130M 73dBm 10 PER 135M 270M 66dBm 10 PER 2dBi 2 4 2 5GH
17. Device O Enter the new device s PIN Press the button of the new device in two minutes Figure 4 18 Add A New Device Step 2 Press and hold the WPS button of the client device directly Step 3 The Wi Fi Protected Setup LED flashes for two minutes during the Wi Fi Protected Setup process Step 4 When the WPS LED is on the client device has successfully connected to the Router Step 5 Refer back to your client device or its documentation for further instructions Il Enter the client device s PIN on the Router Use this method if your client device does not have the WPS button but has a Wi Fi Protected Setup PIN number Step 1 Keep the default WPS status as Enabled and click the Add device button in Figure 4 16 then Figure 4 19 will appear Add A New Device Enter the new device s PIN Press the button of the new device in two minutes Figure 4 19 Add A New Device Step 2 Enter the PIN number from the client device in the field on the above WPS screen Then click Connect button Step 3 Connect successfully will appear on the screen of Figure 4 19 which means the client device has successfully connected to the Router a7 s TL WDR3600 BYU ele TEA Ele Rel Ade ti Ill Enter the Router s PIN on your client device Use this method if your client device asks for the Router s PIN number Step 1 On the client device enter the PIN number listed on the Router s Wi Fi Protected Setup
18. Egress bandwidth This field displays the max and mix upload bandwidth through the Internet port the default is 0 gt Ingress bandwidth This field displays the max and mix download bandwidth through the Internet port the default is 0 gt Enable This displays the status of the rule gt Modify Click Modify to edit the rule Click Delete to delete the rule To add modify a Bandwidth Control rule follow the steps below 1 Click Add New shown in Figure 4 97 you will see a new screen shown in Figure 4 98 2 Enter the information like the screen shown below Bandwidth Control Rule Settings Enable Port Range CEA Protocol Min Bandwidthfkbps hax Bandwidthikbps Egress Bandwidth Ingress Bandwidth E Figure 4 98 Bandwidth Control Rule Settings 3 Click the Save button 4 17 IP amp MAC Binding Setting IP amp MAC Binding Figure 4 99 the IP amp MAC Binding menu There are two submenus under the IP amp MAC Binding menu shown in Figure 4 99 Binding Settings and ARP List Click any of them and you will be able to scan or configure the corresponding function The detailed explanations for each submenu are provided below 4 17 1 Binding Settings This page displays the IP amp MAC Binding Setting table you can operate it in accord with your desire shown in Figure 4 100 98 TL WDR3600 BCT eee EN a ella o vi Binding Settings ARP Binding Disabl
19. L2TP is the method used to enable Point to Point sessions via the Internet on the Layer Two level To allow L2TP tunnels to pass through the Router click Enable IPSec Passthrough Internet Protocol security IPSec is a suite of protocols for ensuring private secure communications over Internet Protocol IP networks through the use of cryptographic security services To allow IPSec tunnels to pass through the Router click Enable ALG It is recommended to enable Application Layer Gateway ALG because ALG allows customized Network Address Translation NAT traversal filters to be plugged into the Mir oE TL WDR3600 EA AAEE a Meier lolimacelenccys gateway to support address and port translation for certain application layer control data protocols such as FTP TFTP H323 etc e FTP ALG To allow FTP clients and servers to transfer data across NAT click Enable e TFTP ALG To allow TFTP clients and servers to transfer data across NAT click Enable e H323 ALG To allow Microsoft NetMeeting clients to communicate across NAT click Enable e RTSP ALG To allow some media player clients to communicate with some streaming media servers across NAT click Enable Click the Save button to save your settings 4 12 2 Advanced Security Choose menu Security Advanced Security and then you can protect the Router from being attacked by TCP SYN Flood UDP Flood and ICMP Flood in the screen as shown in Figure 4 70
20. MAC Filtering Disabled Filtering Rules Deny the stations specified by any enabled entries in the listto access Allow the stations specified by any enabled entries in the listto access ID MAC Address Status Description Modify 1 00 0A EB B0 00 0B Enabled Wireless station A Modify Delete Add New Enable All Disable All Delete All Figure 4 24 Wireless MAC Filtering To filter wireless users by MAC Address click Enable The default setting is Disabled gt MAC Address The wireless station s MAC address that you want to filter gt Status The status of this entry either Enabled or Disabled gt Description A simple description of the wireless station To Add a Wireless MAC Address filtering entry click the Add New button The Add or Modify Wireless MAC Address Filtering entry page will appear shown in Figure 4 25 Add or Modify Wireless MAC Address Filtering entry Status Enabled w Figure 4 25 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry follow these instructions 1 Enter the appropriate MAC Address into the MAC Address field The format of the MAC Address iS XX XX XX XX XX XX X is any hexadecimal digit For example 00 OA EB B0 00 06B 2 Give a simple description for the wireless station in the Description field For example Wireless station A 3 Select Enabled or Disabled for this entry on the Status drop down list 4 Click the Save butto
21. Mew Delete All Current Mo Fage Figure 4 86 Target Settings gt Target Description Here displays the description about the target and this description is unique gt Information The target can be IP address port or domain name gt Modify To modify or delete an existing entry To add a new entry please follow the steps below 1 Click the Add New button 2 In Mode field select IP Address or Domain Name 3 Ifyou select IP Address the screen shown is Figure 4 87 Add or Modify an Access Target Entry Mode IP Address kd Protocol Common Serice Port please select Y Figure 4 87 Add or Modify an Access Target Entry 1 In Target Description field create a unique description for the target e g Target_1 2 In IP Address field enter the IP address of the target 3 Select a common service from Common Service Port drop down list so that the Target Port will be automatically filled If the Common Service Port drop down list doesn t have the service you want specify the Target Port manually 4 In Protocol field select TCP UDP ICMP or ALL from the drop down list 4 Ifyou select Domain Name the screen shown is Figure 4 88 91 TL WDR3600 EA AAEE a Meier lolimacelenccys Add or Modify an Access Target Entry Figure 4 88 Add or Modify an Access Target Entry 1 In Target Description field create a unique description for the target e g Target_1 2 In Domain Name field enter
22. Select the channel width from the drop down list The default setting is automatic which can adjust the channel width for your clients automatically e Note If 11b only 11g only or 11bg mixed is selected in the Mode field the Channel Width selecting field will turn grey and the value will become 20M which is unable to be changed Channel This field determines which operating frequency will be used The default channel is set to Auto so the AP will choose the best channel automatically It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point 34 TL WDR3600 Bye ele Ele Rel Leti gt Enable SSID Broadcast When wireless clients survey the local area for wireless networks to associate with they will detect the SSID broadcast by the Router If you select the Enable SSID Broadcast checkbox the Wireless Router will broadcast its name SSID on the air gt Enable WDS Bridging Check this box to enable WDS With this function the Router can bridge two or more Wlans If this checkbox is selected you will have to set the following parameters as shown in Figure 4 15 Make sure the following settings are correct 5ID to be bridged ESSID to be bridged Example 00 10 O0F 11 22 33 WEP Index Auth type Password Figure 4 15 WDS Setting gt SSID to be bridged The SSID of the AP your Router is going to connect to as a client You ca
23. appear as shown in Figure 4 106 Serice Provider Mo 1P rn no Ip corr Goto register User Name Domain Name C Enable DONS Connection Status cons not launching Figure 4 106 No ip com DDNS Settings To set up for DDNS follow these instructions 1 Enter the User Name for your DDNS account 2 Enter the Password for your DDNS account 3 Enter the Domain Name you received from dynamic DNS service provider 4 Click the Login button to login to the DDNS service Connection Status The status of the DDNS service connection is displayed here Click Logout to log out the DDNS service cs Note If you want to login again with another account after a successful login please click the Logout button then input your new username and password and click the Login button 103 TL WDR3600 BCT ee BTU SF Tave elit 4 19 System Tools System Tools Diagnostic Firmware Upgrade Factory Defaults Backup amp Restore Reboot Password System Log Statistics Figure 4 107 The System Tools menu Choose menu System Tools and you can see the submenus under the main menu Time Settings Diagnostic Firmware Upgrade Factory Defaults Backup 8 Restore Reboot Password System Log and Statistics Click any of them and you will be able to configure the corresponding function The detailed explanations for each submenu are provided below 4 19 1 Time Setting Choose menu System Tools T
24. choose the appropriate connection type click the Detect button to allow the Router to automatically search your Internet connection for servers and protocols The connection type will be reported when an active Internet service is successfully detected by the Router This report is for your reference only To make sure the connection type your ISP provides please refer to the ISP The various types of Internet connections that the Router can detect are as follows e PPPoE Connections which use PPPoE that requires a user name and password e Dynamic IP Connections which use dynamic IP address assignment e Static IP Connections which use static IP address assignment The Router can not detect PPTP L2TP BigPond connections with your ISP If your ISP uses one of these protocols then you must configure your connection manually 4 4 2 LAN Choose menu Network LAN you can configure the IP parameters of the LAN on the screen as below 302 TL WDR3600 MCU ete BIUE ETT Meier lolimacelenccys MAC Address Q0 04 EB 13 049 8F IP Address 192 168 0 1 subnet Mask 255 255 255 0 MM Dave Figure 4 10 LAN gt MAC Address The physical address of the Router as seen from the LAN The value can t be changed gt IP Address Enter the IP address of your Router or reset it in dotted decimal notation factory default 192 168 0 1 gt Subnet Mask An address code that determines the size of the network Normall
25. displayed here The default PIN of the Router can be found in the label or User Guide gt Restore PIN Restore the PIN of the Router to its default gt Gen New PIN Click this button and then you can get a new random value for the Router s PIN You can ensure the network security by generating a new PIN gt Disable Router s PIN If this box is checked and then wireless clients will not be able to connect to the wireless network with PIN code gt Add device You can add a new device to the existing network manually by clicking this button If the wireless adapter supports Wi Fi Protected Setup WPS you can establish a wireless connection between wireless adapter and Router using either Push Button Configuration PBC method or PIN method Cs Note To build a successful connection by WPS you should also do the corresponding configuration of the new device for WPS function meanwhile I Use the Wi Fi Protected Setup Button Use this method if your client device has a Wi Fi Protected Setup button Step 1 Press the WPS Reset button on the back panel of the Router as shown in Figure 4 17 You can also keep the default WPS status as Enabled and click the Add device button in Figure 4 16 Then choose Press the button of the new device in two minutes and click Connect shown in Figure 4 18 36 TL WDR3600 EA AAEE a ella vi Figure 4 17 Add A New
26. from 18 00 to 20 00 on Saturday and Sunday you should first follow the settings below 1 Click Add New button shown in Figure 4 89 to enter the Advanced Schedule Settings page 2 In Schedule Description field create a unique description for the schedule e g Schedule_1 3 In Day field check the Select Days radio button and then select Sat and Sun 4 In Time field enter 1800 in Start Time field and 2000 in Stop Time field 5 Click Save to complete the settings Then you will go back to the Schedule Settings page and see the following list D Schedule Description Day Time Modify 1 schedule _1 Sat Sun 18 00 20 00 Edit Delete 4 15 Advanced Routing Advanced Routing System Routing Table Figure 4 91 Advanced Routing There are two submenus under the Advanced Routing menu as shown in Figure 4 91 Static Routing List and System Routing Table Click any of them and you will be able to configure the corresponding function 94 TL WDR3600 EAA BIUE ETT Meier lolimacelenccys 4 15 1 Static Routing List Choose menu Advanced Routing Static Routing List and then you can configure the Static route in the next screen shown in Figure 4 92 A static route is a pre determined path that network information must travel to reach a specific host or network static Routing Destination Network Subnet Mask Default Gateway Status Modify Add Mew Figur
27. from 18 00 to 20 00 on Saturday and Sunday and forbid other hosts in the LAN to access the Internet you should follow the settings below 1 Click the submenu Rule of Access Control in the left to return to the Rule List page Select Enable Internet Access Control and choose Allow the packets specified by any enabled access control policy to pass through the Router We recommend that you click Setup Wizard button to finish all the following settings Click the submenu Host of Access Control in the left to enter the Host List page Add a new entry with the Host Description is Host_1 and MAC Address is 00 11 22 33 44 AA Click the submenu Target of Access Control in the left to enter the Target List page Add a new entry with the Target Description is Target_1 and Domain Name is www google com Click the submenu Schedule of Access Control in the left to enter the Schedule List page Add a new entry with the Schedule Description is Schedule 1 Day is Sat and Sun Start Time is 1800 and Stop Time is 2000 Click the submenu Rule of Access Control in the left Click Add New button to add a new rule as follows 1 In Rule Name field create a name for the rule Note that this name should be unique for example Rule 1 2 In Host field select Host_1 3 In Target field select Target _1 88 TL WDR3600 EA AAEE a ella vi 4 In Schedule field select Schedule_1 5 In Status field select Enable 6 Click Save to co
28. install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps Korea Warning Statements sa FAGHE 22 AREA UE O WS NCC Notice Ae HY SU ae as SZ RR A SERS ZS MAREA eS A E AAA MAD K BY See EF a aT EE Re AE RD RN REL EH Nh a RL LAR FBG a SARA FBS ESTE A We JE Die DI FEIR RH MIARA IK EI ALE TESS L ER EA ES E PERRA AMA BCT Se PAA aH EAN E EE A TH o y MlpoaykT ceptudikoBaHo 3riaHo c npaBunamu cucrema YkpCENMPO Ha BIAnNoBiAHicTte BUMOraM HODPMaTUBHUX OOKYMeHTIB Ta BUMOTaM LUO nepernbayehi 4NHHNMA 3aKOHOAABYUMU AKTaMu YkpalHn TP LINK TP LINK TECHNOLOGIES CO LTD DECLARATION OF CONFORMITY For the following equipment Product Description N600 Wireless Dual Band Gigabit Router Model No TL WDR3600 Trademark TP LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives Directives 1999 5 EC Directives 2004 108 EC Directives 2006 95 EC Directives 1999 519 EC Directives 2011 65 EU The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1 7 1 2006 ETSI EN 301 489 1 V1 8 1 2008 amp ETSI EN 301 489 17 V2 1 1 2009 EN 55022 2010 EN 55024 2010 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 EN60950 1 2006 A11 2009 A1 2010 A12 2011 EN62311 2008 EN 301 893 EN 302
29. month in the first field the week in the second field the day in the third field and the time in the last field Daylight Saving Status Displays the status whether the Daylight Saving is in use To set time manually 1 2 3 4 Select your local time zone Enter the Date in Month Day Year format Enter the Time in Hour Minute Second format Click Save To set time automatically 1 2 3 Select your local time zone Enter the address or domain of the NTP Server I or NTP Server Il Click the Get GMT button to get system time from Internet if you have connected to the Internet To set Daylight Saving 1 2 Check the box to enable Daylight Saving Select the start time from the drop down lists in the Start field Select the end time from the drop down lists in the End field Click the Save button to save the settings 105 TL WDR3600 EAA AEAEE a Meier lolimacelenccys e Enable Daylight Saving Daylight Saving Status daylight saving is down Figure 4 109 Time settings Note 1 This setting will be used for some time based functions such as firewall You must specify your time zone once you login to the router successfully otherwise these functions will not take effect 2 The time will be lost if the router is turned off 3 The Router will automatically obtain GMT from the Internet if it is configured accordingly 4 The Daylight Saving will take effect one minute afte
30. next screen shown in Figure 4 94 System routing table views all of the valid route entries in use The Destination IP address Subnet Mask Gateway and Interface will be displayed for each entry System Routing Table Destination Network Subnet Mask Interface 192 168 0 0 255 255 255 0 LAN amp WLAN 1 0 0 0 255 0 0 0 WAN 239 0 0 0 255 0 0 0 LAN amp WLAN 0 0 0 0 0 0 0 0 VAN Figure 4 94 System Routing Table gt Destination Network The Destination Network is the address of the network or host to which the static route is assigned gt Subnet Mask The Subnet Mask determines which portion of an IP address is the network portion and which portion is the host portion gt Gateway This is the IP address of the gateway device that allows for contact between the Router and the network or host gt Interface This interface tells you either the Destination IP Address is on the LAN amp WLAN internal wired and wireless networks or on the WAN Internet 4 16 Bandwidth Control Bandwidth Control Rules List Figure 4 95 Bandwidth Control 96 TL WDR3600 BTU EN a eli ovio There are two submenus under the Bandwidth Control menu as shown in Figure 4 95 Control Settings and Rules List Click any of them and you will be able to configure the corresponding function The detailed explanations for each submenu are provided below 4 16 1 Control Settings Choose menu Bandwidth Control Co
31. number used is 8080 please enter http 202 96 12 8 8080 in your browser Later you may be asked for the Router s password After successfully entering the username and password you will be able to access the Router s web based utility 2 Be sure to change the Router s default password to a very secure password 4 13 Parental Control Choose menu Parental Control and then you can configure the parental control in the screen as shown in Figure 4 73 The Parental Control function can be used to control the internet activities of the child limit the child to access certain websites and restrict the time of surfing 80 TL WDR3600 EA AAEE a ella vi Parental Control Settings Mon Parental PCs not listed will not be able to access the Internet Parental Control Disable Enable MAC Address of Parental PC A MAC Address of Your PC 40 61 86 ct20 7a Copy To Above ID MAC address Website Description Schedule Enable Add New Current Mo Page Figure 4 73 Parental Control Settings To add a new entry please follow the steps below 1 Click the Add New button and the next screen will pop up as shown in Figure 4 74 Add or Modify Parental Control Entry The Schedule is based on the time ofthe Router The time can be setin System Tools Time settings MAC Address of Child PC All MAC Address In Current LON please select w Website Description Allowed Domain Name pO PO PO
32. or above Enter 0 to disable the update WEP It is based on the IEEE 802 11 standard If you check this radio button you will find a notice in red as show in Figure 4 38 sp2 TL WDR3600 BCT ee BTU ETT EEIE OIT ipe WEP Key Format Hexadecimal Key Selected WEP Key Password Key Type Key 1 Disabled Y We do not recommend using the WEF encryption ifthe device operates in 202 11n mode due to the fact that YEP is not supported by 802 11n specification Figure 4 38 WEP e Type you can choose the type for the WEP security on the drop down list The default setting is Automatic which can select Shared Key or Open System authentication type automatically based on the wireless station s capability and request e WEP Key Format Hexadecimal and ASCII formats are provided here Hexadecimal format stands for any combination of hexadecimal digits 0 9 a f A F in the specified length ASCII format stands for any combination of Keyboard characters in the specified length e WEP Key Select which of the four keys will be used and enter the matching WEP key that you create Make sure these values are identical on all wireless stations in your network e Key Type You can select the WEP key length 64 bit or 128 bit or 152 bit for encryption Disabled means this WEP key entry Is invalid 64 bit You can enter 10 hexadecimal digits any combination of 0 9 a f A F zero key is not promot
33. page as shown in Figure 4 102 Find IP amp MAC Binding Entry MAC Address 00 E0 4C 00 07 BE ID MAC Address IPF Address Bind Link 1 00 E0 46 00 07 BE 192 168 0 4 To page Figure 4 102 Find IP amp MAC Binding Entry Click the Enable All button to make all entries enabled Click the Delete All button to delete all entries 4 17 2 ARP List To manage the computer you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list and you could also configure the items on the ARP list This page displays the ARP List it shows all the existing IP amp MAC Binding entries shown in Figure 4 103 ARP List MAC Address IP Address Status Configure 40 61 86 CF 20 7A 192 168 0 101 Unbound Load Delete Load All Figure 4 103 ARP List 1 MAC Address The MAC address of the controlled computer in the LAN 2 IP Address The assigned IP address of the controlled computer in the LAN 3 Status Indicates whether or not the MAC and IP addresses are bound 4 Configure Load or delete an item gt Load Load the item to the IP amp MAC Binding list gt Delete Delete the item Click the Bind All button to bind all the current items available after enable Click the Load All button to load all items to the IP amp MAC Binding list Click the Refresh button to refresh all items 100 TL WDR3600 EA AAEE a MCT er lolimacelenccys Note An item could not be l
34. password here Storage Authority Choose Read and Write or Read Only from the drop down list to assign access authority of Storage Sharing to the user FTP Access Choose Yes or No from the drop down list to decide whether the user can access FTP Server or not Save You can click the SAVE button to save your settings Back You can click the Back button to discard the settings and just go to the media server configuration page Note Please restart the service for the new settings to take effect If you cannot use the new user name and password to access the shares press Windows logo R to open the Run dialog box and type net use 192 168 1 1 delete yes and press Enter 192 168 1 1 is your router s LAN IP address If the LAN IP of the modem connected with your router is 192 168 1 x the default LAN IP of the Router will automatically switch from 192 168 1 1 to 192 168 0 1 to avoid IP conflict in this case please try net use 192 168 0 1 delete yes 68 TL WDR3600 EA AAEE a ella vi 4 10 NAT Choose NAT and you can enable or disable the NAT function NAT Control Setting ote Make sure the NAT is enable if you want the Hardware NAT configuration take effect Current NAT Status Enable Disable urrent Hardware NAT Status Enable Disable Figure 4 60 The Forwarding menu 4 11 Forwarding Port Triggering DMZ UPnP Figure 4 61 The Forwarding menu There are four
35. the background Click the Save button to save your settings 6 If your ISP provides PPTP connection please select PPTP Russia PPTP option And you should enter the following parameters Figure 4 9 28 TL WDR3600 BCU BIE ETT Meier lolimacelenccys WAN WAN Connection Type PPTPRussia PPTP we User Name username Disconnected DynamicIP Static IP Server IP Address Hame IP Address Subnet Mask Gateway DNS Internet IP Address Internet DHS MTU Size in bytes 1420 The defaultis 1420 do not change unless necessary Max Idle Time minutes 0 means remain active at all times WAN Connection Mode Connect on Demand Connect Automatically Connect Manually Figure 4 9 PPTP Settings User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive Dynamic IP Static IP Choose either as you are given by your ISP and enter the ISP s IP address or the domain name If you choose static IP and enter the domain name you should also enter the DNS assigned by your ISP And click the Save button Click the Connect button to connect immediately Click the Disconnect button to disconnect immediately Connect on Demand You can configure the Router to disconnect from your Internet connection after a specified period of inactivity Max Idle Time If your Internet connection has been terminated due to inactivity Connect on Demand ena
36. you the unexpected networking experience at speed much faster than 802 11g It is also compatible with all IEEE 802 119 and IEEE 802 11b products Multiple Security Protections With multiple protection measures including SSID broadcast control and wireless LAN 64 128 152 bit WEP encryption Wi Fi Protected Access WPA2 PSK WPA PSK as well as advanced Firewall protections the TL WDR3600 N600 Wireless Dual Band Gigabit Router provides complete data privacy Flexible Access Control The TL WDR3600 N600 Wireless Dual Band Gigabit Router provides flexible access control so that parents or network administrators can establish restricted access policies for children or staff It also supports Virtual Server and DMZ host for Port Triggering and then the network administrators can manage and monitor the network in real time with the remote management function Simple Installation gt Since the Router is compatible with virtually all the major operating systems it is very easy to manage Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide Before installing the Router please look through this guide to know all the Router s functions TL WDR3600 BCU ele TEA EO Rel Leti 1 2 Conventions The Router or TL WDR3600 mentioned in this guide stands for TL WDR3600 N600 Wireless Dual Band Gigabit Router without any explanation 13 Main Features gt Complies with IEEE 802 11n to p
37. your Internet connection after a specified period of inactivity Max Idle Time If your Internet connection has been terminated due to inactivity Connect on Demand enables the Router to automatically re establish your connection as soon as you attempt to access the Internet again If you wish to activate Connect on Demand check the radio button If you want your Internet connection to remain active at all times enter 0 in the Max Idle Time field Otherwise enter the number of minutes you want to have elapsed before your Internet connection terminates gt Connect Automatically Connect automatically after the Router is disconnected To use this option check the radio button gt Connect Manually You can configure the Router to make it connect or disconnect manually After a specified period of inactivity Max Idle Time the Router will disconnect from your Internet connection and you will not be able to re establish your connection automatically as soon as you attempt to access the Internet again To use this option check the radio button If you want your Internet connection to remain active at all times enter 0 in the Max Idle Time field Otherwise enter the number of minutes that you wish to have the Internet connecting last unless a new link is requested Caution Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time because some applications are visiting the Internet continually in
38. 4 12 4 Remote Management Choose menu Security Remote Management and then you can configure the Remote Management function in the screen as shown in Figure 4 72 This feature allows you to manage your Router from a remote location via the Internet 79 TL WDR3600 BTC BITE ETT ella o vi Remote Management Web Management Port Remote Management IP Address 0 0 0 0 Enter 255 255 255 255 for alli nave Figure 4 72 Remote Management gt Web Management Port Web browser access normally uses the standard HTTP service port 80 This Router s default remote management web port number is 80 For greater security you can change the remote management web port to a custom port by entering that number in the box provided Choose a number between 1 and 65534 but do not use the number of any common service port gt Remote Management IP Address This is the current address you will use when accessing your Router from the Internet This function is disabled when the IP address is set to the default value of 0 0 0 0 To enable this function change 0 0 0 0 to a valid IP address If set to 295 255 255 255 then all the hosts can access the Router from internet Note 1 To access the Router you should type your Router s WAN IP address into your browser s address in IE or Location in Navigator box followed by a colon and the custom port number For example if your Router s WAN address is 202 96 12 8 and the port
39. 502 The product carries the CE Mark C 1588 Person is responsible for marking this declaration Yang Hongliang Product Manager of International Business Date of issue 2012 TP LINK TECHNOLOGIES CO LTD Building 24 floors 1 3 4 5 and 28 floors 1 4 Central Science and Technology Park Shennan Rd Nanshan Shenzhen China Package C ont ntS esisin 1 Chapter 1 INtoductoNiaarsncaniania is 2 11 OVERVIEW Of the ROM e ed 2 az CONVENON S te a dl ll o 3 To Main Reales manera 3 TA PERC La VO E o ote cl dos OD ated 4 LAY TEMG PROM Panel cade ld 4 AZ The Rear Pane laica cialis 5 Chapter 2 Connecting the Router ooocconcccncocccocccocccnncocnconanonnnnnncnnrnnncnnnenarenanenanos 7 Zeal System REg menlo uns ia a enol 7 2 2 Installation Environment Requirements ccccccecceeceeeeeceeceeeeeeseeseeseeeeeseeeeetseees T 23 Connecting the ROM dde o alte 7 Chapter 3 Quick Installation Guide oncoccconconcocnconnoccconconcccncnnronrnnncnncnanenannnnos 9 91 TEGPP Comtiquralo sana 9 32 Quick Insta lato GUE ida 10 Chapter 4 Configuring the Router occoncccncocccocccocccnnconaronanonnnnancnnnnnarenaronaronnnnns 19 MAE o A O ad nae E 19 a ame 2 110 E O PO A oe en ome re ee eee 19 A A 21 Age DING IW Ol Kioto E din 21 4AN WAN euredenn cee dat atau a el aden i i ote dat eta tu had cul 21 HAZ AN dd AS 30 BAS MAC GIONE eadra a a E E 31 4o Dualband e S 32 AG Wireless 24GH
40. Adapter for TL WDR3600 N600 Wireless Dual Band Gigabit Router Quick Installation Guide Vv V V WV Resource CD for TL WDR3600 N600 Wireless Dual Band Gigabit Router including e This Guide e Other Helpful Information Ss Note Make sure that the package contains the above items If any of the listed items are damaged or missing please contact with your distributor TL WDR3600 MCU ee BIUE a Meier lolimacelenccys Chapter 1 Introduction Thank you for choosing the TL WDR3600 N600 Wireless Dual Band Gigabit Router 1 1 Overview of the Router The TL WDR3600 N600 Wireless Dual Band Gigabit Router integrates 4 port Switch Firewall NAT Router and Wireless AP Powered by 3x3 MIMO technology the N600 Wireless Dual Band Gigabit Router delivers exceptional range and speed which can fully meet the need of Small Office Home Office SOHO networks and the users demanding higher networking performance Your wireless connections are radio band selectable to avoid interference in your area and the four built in Gigabit ports supply high speed connection to your wired devices Incredible Speed The TL WDR3600 N600 Wireless Dual Band Gigabit Router provides up to 300Mbps 2 4GHz 300Mbps 5GHZ wireless connection with other 802 11n wireless clients The incredible soeed makes it ideal for handling multiple data streams at the same time which ensures your network stable and smooth The performance of this 802 11n wireless Router will give
41. Click the Login button to login the DDNS service Connection Status The status of the DDNS service connection is displayed here Click Logout to log out of the DDNS service cf Note If you want to login again with another account after a successful login please click the Logout button then input your new username and password and click the Login button 4 18 2 Dyndns org DDNS If the dynamic DNS Service Provider you select is www dyndns org the page will appear as shown in Figure 4 105 serice Provider Dyndns sw dyndns org Goto register User Name Username Password Domain Name C Enable DONS Connection Status DDNS not launching Save Figure 4 105 Dyndns org DDNS Settings To set up for DDNS follow these instructions 1 Enter the User Name for your DDNS account 2 Enter the Password for your DDNS account 3 Enter the Domain Name you received from dynamic DNS service provider 4 Click the Login button to login to the DDNS service Connection Status The status of the DDNS service connection is displayed here Click Logout to logout of the DDNS service 102 TL WDR3600 EI AAEE a Meier lolimacelenccys Cf Note If you want to login again with another account after a successful login please click the Logout button then input your new username and password and click the Login button 4 18 3 No ip com DDNS If the dynamic DNS Service Provider you select is www no ip com the page will
42. Connection Type If you select Auto Detect the Router will automatically detect the connection type your ISP provides Make sure the cable is securely plugged into the Internet port before detection The appropriate configuration page will be displayed when an active Internet service is successfully detected by the Router 1 If the connection type detected is PPPoE the next screen will appear as shown in Figure 3 7 Quick Setup PPPoE User Name Username Password Confirm Password Figure 3 7 Quick Setup PPPoE gt User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive If you have difficulty with this process please contact your ISP gt Confirm Password Enter the password again to make sure that the password is correct 2 If the connection type detected is Dynamic IP the next screen will appear as shown in Figure 3 8 A MAC address is a 12 digit code assigned to a unique piece of hardware for identification Some ISPs will register the MAC address of your computer when you access the Internet for the first time via the cable ADSL modem they offered lf you add a router into your network to share the Internet the ISP may not recognize the new MAC TL WDR3600 EA AAEE a RIEL aoti address of the router and will not offer the Internet connection any more Therefore it is necessary to clone the MAC address of the computer to the router Quic
43. Repair Bridge Connections Create Shorkecut Delete Rename Properties Figure B 1 120 TL WDR3600 BTU BITE SF Tave Meier lolimacelenccys 4 Inthe prompt page that showed below double click on the Internet Protocol TCP IP L Local Area Connection Properties x General Authentication Advanced Connect using E Realtek BTL8139 Family PCI Fast EX This connection uses the following items F Install Uniretall Properties Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected e Notify me when this connection has limited or no connectivity Figure B 2 5 The following TCP IP Properties window will display and the IP Address tab is open on this window by default 121 TL WDR3600 BTU ENa Meier lolimacelenccys 6 Select Obtain an IP address automatically and Obtain DNS server automatically as shown in the Figure below Internet Protocol TCP IP Properties x General Alternate Configuration fou can get IF settings assigned automatically if your network supports this capability Othenvise You need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address F address Subnet mask
44. S technology using OFDM modulation and operating in the unlicensed radio spectrum at 2 4GHz and backward compatibility with IEEE 802 11b devices and WEP encryption for security gt DDNS Dynamic Domain Name System The capability of assigning a fixed host and domain name to a dynamic Internet IP Address gt DHCP Dynamic Host Configuration Protocol A protocol that automatically configure the TCP IP parameters for the all the PC s that are connected to a DHCP server gt DMZ Demilitarized Zone A Demilitarized Zone allows one local host to be exposed to the Internet for a special purpose service such as Internet gaming or videoconferencing gt DNS Domain Name System An Internet Service that translates the names of websites into IP addresses gt Domain Name A descriptive name for an address or group of addresses on the Internet gt DSL Digital Subscriber Line A technology that allows data to be sent or received over existing traditional phone lines gt ISP Internet Service Provider A company that provides access to the Internet gt MTU Maximum Transmission Unit The size in bytes of the largest packet that can be transmitted gt NAT Network Address Translation NAT technology translates IP addresses of a local area network to a different IP address for the Internet gt PPPoE Point to Point Protocol over Ethernet PPPoE is a protocol for connecting remote hosts to the Inter
45. SP gt Secondary DNS Optional Input the IP address of another DNS server if your ISP provides two DNS servers 58 TL WDR3600 A AAEE a Meier lolimacelenccys Cf Note To use the DHCP server function of the Router you must configure all computers on the LAN as Obtain an IP Address automatically 4 8 2 DHCP Clients List Choose menu DHCP DHCP Clients List you can view the information about the clients attached to the Router in the screen as shown in Figure 4 45 DHCP Clients List D Client Name MAC Address Assigned IP Lease Time 1 th 113ea910272d 40 61 G6 CF 20 7A 192 166 0 100 01 49 59 Figure 4 45 DHCP Clients List gt Client Name The name of the DHCP client gt MAC Address The MAC address of the DHCP client gt Assigned IP The IP address that the Router has allocated to the DHCP client gt Lease Time The time of the DHCP client leased After the dynamic IP address has expired a new dynamic IP address will be automatically assigned to the user You cannot change any of the values on this page To update this page and to show the current attached devices click the Refresh button 4 8 3 Address Reservation Choose menu DHCP Address Reservation you can view and add a reserved address for clients via the next screen shown in Figure 4 46 When you specify a reserved IP address for a PC on the LAN that PC will always receive the same IP address each time when it acces
46. This mode also supports the Max Idle Time function as Connect on Demand mode The Internet connection can be disconnected automatically after a specified inactivity period and re established when you attempt to access the Internet again Click the Connect button to connect immediately Click the Disconnect button to disconnect immediately Caution Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background If you want to do some advanced configurations please click the Advanced button and the page shown in Figure 4 6 will then appear 24 TL WDR3600 BCT eee UE a RIEL ovio PPPoE Advanced Settings MTU Size in bytes 1450 The defaultis 1480 do not change unless necessary C Use IP address specified by ISP ISP Specified IP Address poon Detect Online Interval bo seconds 0 120 seconds the default is 0 0 means not detecting C Use the following ONS Servers Secondary DNS 0 0 0 0 Optional Figure 4 6 PPPoE Advanced Settings gt MTU Size The default MTU size is 1480 bytes which is usually fine It is not recommended that you change the default MTU Size unless required by your ISP gt Service Name AC Name The service name and AC Access Concentrator name should not be configured unless you are sure it is necessary for your ISP In most cases leaving these fields bla
47. Type Unknown IP Routing Enabled z WINS Proxy Enabled Ethernet adapter Local Area Connection Connection specific DNS Suffix Description Realtek PCIe FE Family Controller 2 Physical Address 1 48 61 86 CF 20 7A Dhep Enabled IP Address 172 351 786 224 Subnet Mask 255 255 255 0 Default Gateway DNS Servers s 172 31 51 2 Figure 3 9 Find MAC Address A TL WDR3600 MYT ee ENa Meier lolimacelenccys 3 If the connection type detected is Static IP the next screen will appear as shown in Figure 3 10 Configure the following parameters and then click Next to continue Quick Setup Static IP IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 Optional Primary DNS 0 000 Optional Secondary DNS 0 0 0 0 Optional Figure 3 10 Quick Setup Static IP gt IP Address This is the WAN IP address as seen by external users on the Internet including your ISP Your ISP will provide you with the IP address you need to enter here Enter the IP address into the field gt Subnet Mask The Subnet Mask is used for the WAN IP address Your IPS will provide you with the subnet mask which is usually 255 255 255 0 gt Default Gateway Your ISP will provide you with the Gateway address which is the ISP server s address Enter the gateway IP address into the box if required gt Primary DNS Enter the DNS Server IP address into the box if required gt Sec
48. Z ii di 33 AL Wireless Setihg Scerni A A gees 33 462 WPSorie a E idaietta eda natiuneteanidas 35 4 6 3 Wireless Security cooocccocccccnoccnoconononnonanocncnonononanonannonnnonanonaronannnnanonaninnnnns 38 46 4 Wireless MAC Eller iS 41 4 6 5 Wireless Advanced ocooocccocccoccoconcconccoononnnononononnonononancnnnnonnnonannnanconnnenanennness 43 400 0 Wireless otallStls sitio Ln 45 AT Wireless olaa 45 CONTENTS ATA Wireless Seting Ses setecenceecbesue ese lhe AA 46 Bll WES A lsc dade A occa ebice acoso eect 48 AT 3 Wireless SEOCUIN Vi a hace aceeaeeeheaeieesireueete 50 4 7 4 Wireless MAC Filtering sien ce isl cote iio 53 4 7 5 Wireless Advanced nica lado 55 ATO Wireless Statistics neata 57 A e o a E E 57 40 1 DACP SENGS oras A a 58 1o DAGA leal aos 59 4 8 3 Address Reservation ooncconccconnconcccnnoconononnonnnononononcnnnnonancnnnnnnnnenonenancnnnnss 99 A9 UOB US E 60 ADT Storage Shang 0 id 61 BZ O sacme se deeahie a tosten aa eacae 62 439 3 Medid SEE ios 64 AO A pe E ENTA 66 499 USCrACCOUINS risiet a a a E 67 AMO NA cn cdi 69 AST FO cales 69 ANET MAS ES e E nO 69 AZ POR MITIN tia 11 dE E y PAR ene eee ee a eee ees 73 AMA UPIP ercran dos 74 AZ A e ubeln Glia ain 75 4121 Basic SOCUMILY eerie dis 75 4 12 2 Advanced ecu ersero in nseries 77 41259 Oca Management s lt 12 cia tierce do Ls 78 4 12 4 Remote Management cccccccscceseceseceeceeeceeesaeesaeeceesauessesueesees
49. a particular receiving station and negotiate the sending of a data frame The default value is 2346 Fragmentation Threshold This value is the maximum size determining whether packets will be fragmented Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets 2346 is the default setting and is recommended DTIM Interval This value determines the interval of the Delivery Traffic Indication Message DTIM A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages When the Router has buffered broadcast or multicast messages for associated clients it sends the next DTIM with a DTIM Interval value You can specify the value between 1 15 Beacon Intervals The default value is 1 which indicates the DTIM Interval is the same as Beacon Interval Enable WMM WMM function can guarantee the packets with high priority messages being transmitted preferentially It is strongly recommended Enable Short GI This function is recommended for it will increase the data capacity by reducing the guard interval time Enabled AP Isolation This function can isolate wireless stations on your network from each other Wireless devices will be able to communicate with the Router but not with each other To use this function check this box AP Isolation is disabled by default 44 TL WDR3600 EA AAEE a Meier lolimacelenccys
50. ade process takes a few moments and the Router restarts automatically when the upgrade is complete 4 19 4 Factory Defaults Choose menu System Tools Factory Defaults and then and you can restore the configurations of the Router to factory defaults on the following screen 108 TL WDR3600 EAA AEAEE a ella o vi Factory Defaults Click the following button to reset all configuration settings to their default values Figure 4 113 Restore Factory Default Click the Restore button to reset all configuration settings to their default values gt The default User Name admin gt The default Password admin gt The default Subnet Mask 255 255 255 0 Note All changed settings will be lost when defaults are restored 4 19 5 Backup amp Restore Choose menu System Tools Backup 8 Restore and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 4 114 Backup amp Restore Figure 4 114 Backup amp Restore Configuration gt Click the Backup button to save all configuration settings as a backup file in your local computer gt To upgrade the Router s configuration follow these instructions e Click the Browse button to find the configuration file which you want to restore e Click the Restore button to update the configuration with the file whose path is the one you have input or selected in the blank
51. age 4 9 USB Settings USB Settings FTP Server Media Server Print Server User Accounts Figure 4 48 The USB Settings menu 60 TL WDR3600 Bye leet TR Sy Tale Rel evi There are four submenus under the USB Settings menu shown in Figure 4 48 Storage Sharing FTP Server Media Server Print Server and User Accounts Click any of them and you will be able to configure the corresponding function 4 9 1 Storage Sharing Choose menu USB Settings Storage Sharing you can configure a USB disk drive attached to the Router and view volume and share properties such as share name capacity used space and free space etc on this page as shown below Storage Sharing Service Status Started C Access shared storage with password Volume Capacity Used Free Use Shared View volume 1 9 GB 1 3 GB 616 MB 62 Open the disk Figure 4 49 Storage Sharing gt Service Status Indicates the Network Sharing service s current status You can click the Start button to start the Storage Sharing service and click the Stop button to stop it gt Volume The volume name of the USB drive the users have access to Volume 1 8 is mapping to USB port1 and Volume 9 16 is mapping to USB port2 gt Capacity The storage capacity of the USB driver gt Used The used space of the USB driver gt Free The available space of the USB driver gt Use The percentage of the used space gt Shared Indicat
52. arameters For advanced settings please refer to 4 7 Wireless 5GHz Then you will see the Finish page gt If you don t make any change on the Wireless page you will see the Finish page as shown in Figure 3 14 Click the Finish button to finish the Quick Setup Quick Setup Finish Congratulations The Router is now connecting you to the Internet For detail settings please click other menus if necessary Figure 3 14 Quick Setup Finish gt If there is anything changed on the Wireless page you will see the Finish page as shown in Figure 3 15 Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup Quick Setup Finish Congratulations The Router is now connecting you to the Internet For detail settings please click other menus if necessary The change of wireless config will not take effect until the Router reboot Figure 3 15 Quick Setup Finish 18 TL WDR3600 MCU ee BIUE a Meier lolimacelenccys Chapter 4 Configuring the Router This chapter will show each Web page s key functions and the configuration way 4 1 Login After your successful login you will see the sixteen main menus on the left of the Web based utility On the right there are the corresponding explanations and instructions Status Quick Setup Network Dual Band Selection Wireless 2 4GHz Wireless 5GHz DHCP USB Settings NAT Forwarding Security Parental Control Acc
53. bles the Router to automatically re establish your connection as soon as you attempt to access the Internet again If you wish to activate Connect on Demand check the radio button If you want your Internet connection to remain active at all times enter O in the Max Idle Time field 29 TL WDR3600 Bye cele OTT TM SF Tale Rele ti Otherwise enter the number of minutes you want to have elapsed before your Internet connection terminates gt Connect Automatically Connect automatically after the Router is disconnected To use this option check the radio button gt Connect Manually You can configure the Router to make it connect or disconnect manually After a specified period of inactivity Max Idle Time the Router will disconnect from your Internet connection and you will not be able to re establish your connection automatically as soon as you attempt to access the Internet again To use this option click the radio button If you want your Internet connection to remain active at all times enter 0 in the Max Idle Time field Otherwise enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested Caution Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background Click the Save button to save your settings cS Note If you don t Know how to
54. ccys streaming or gaming Using this band can avoid interference with 2 4GHz networks or noisy devices like cordless phones and microwave ovens 4 6 Wireless 2 4GHz Wireless 7 4GHz WPS Wireless Security Wireless MAC Filtering Wireless Advanced Wireless Statistics Figure 4 13 Wireless menu There are five submenus under the Wireless menu shown in Figure 4 13 Wireless Settings WPS Wireless Security Wireless MAC Filtering Wireless Advanced and Wireless Statistics Click any of them and you will be able to configure the corresponding function 4 6 1 Wireless Settings Choose menu Wireless 2 4GHz Wireless Settings you can configure the basic settings for the wireless network of 2 4GHz on this page Wireless Settings 2 4GHz Wireless Network Name TP LINK 2 4GHz 13095E Also called the SSID Warning ensure you selecta correct Country to conform local law INCcorrel ETI Ws mav cause ito Mode 11bgn mixed hs Channel Width Enable SSID Broadcast C Enable WDS Bridging nave Figure 4 14 Wireless Settings 2 4GHz gt Wireless Network Name Also called the SSID Service Set Identification Enter a value of up to 32 characters The same name must be assigned to all wireless devices in your network Considering your wireless network security the default SSID is set to be 33 TL WDR3600 BCU BIUE ETT Meier lolimacelenccys TP LINK_2 4GHz_XXXXXX This value is cas
55. cifies the number of data bytes to be sent The default is 64 Ping Timeout Time to wait for a response in milliseconds The default is 800 Vv Vv V WV Traceroute Max TTL Set the maximum number of hops max TTL to be reached in the path to search for the target destination The default is 20 Click Start to check the connectivity of the Internet The Diagnostic Results page displays the result of diagnosis If the result is similar to the following screen the connectivity of the Internet is fine Diagnostic Results Pinging 202 108 22 5 with 64 bytes of data Reply from 202 108 225 bytes 64 time 1 TTL 127 seq 1 Reply from 202 108 225 bytes 64 time 1 TTL 12 sega Reply from 202 108 225 bytes 64 time 1 TTL 12 seg 3 Reply from 202 108 22 5 bytes 64 time 1 TTL 127 seg 4 Ping statistics for 202 108 22 5 Packets Sent 4 Received 4 Lost 0 0 loss Approximate round trip times in milliseconds NI inimum 1 Maximum 1 Average 1 Figure 4 111 Diagnostic Results E Note 1 Only one user can use the diagnostic tools at one time 2 Ping Count Ping Packet Size and Ping Timeout are Ping Parameters and Traceroute Max TTL is Traceroute Parameter 4 19 3 Firmware Upgrade Choose menu System Tools Firmware Upgrade and then you can update the latest version of firmware for the Router on the following screen 107 TL WDR3600 EA AAEE a ella vi Firmware Upgrade
56. ct the Auto scan at same time select an auto scan interval time by drop down list In this case the media server will auto scan the share folders Cf Note The max share folders number is 6 If you want share a new folder when the number has been reached to be 6 you can delete a share folder and then add a new one 4 9 4 Print Server Choose menu USB Settings Print Server you can configure print server on this page as shown below 66 TL WDR3600 BCT ee TUE a Meier lolimacelenccys Print Server Setting Server Status Online Figure 4 57 Pint Server Setting There are two states of the print server they are as follows gt Online Indicates the print service has been turned on and no user is using the print service at present You can click the Stop button to stop the print service gt Offline Indicates the print service feature is disabled You can click Start button to start the print service 4 9 5 User Accounts You can specify the user name and password for Storage Sharing and FTP Server users on this page Storage Sharing users can use Internet Explorer to access files on the USB drive FTP Server users can log into the FTP Server via FTP Client There are two default user accounts that can access the Storage Sharing and FTP Server They are Administrator and Guest as shown in Figure 4 58 Administrator has read write access to Storage Sharing and can access FIP Server while Guest
57. d the Router you can open a command prompt and type ping 192 168 1 1 and then press Enter 3 2 Quick Installation Guide With a Web based utility it is easy to configure and manage the N600 Wireless Dual Band Gigabit Router The Web based utility can be used on any Windows Macintosh or UNIX OS with a Web browser such as Microsoft Internet Explorer Mozilla Firefox or Apple Safari 1 To access the configuration utility open a web browser and type in the default IP address http tplinklogin net in the address field 10 TL WDR3600 EA AAEE a RCIE o vi A Cannot find server Microsoft Internet Explorer File Edit wiew Favorites Tools Help Address http eplinklogin net we o Figure 3 3 Log in the Router After a moment a login window will appear similar to Figure 3 4 Enter admin for the User Name and Password both in lower case letters Then click the OK button or press the Enter key Connect to tplinklogin net TF LIHE Wireless Dual Band Gigabit Router WIRS600 Password Figure 3 4 Login Windows cs Note If the above screen does not pop up it means that your Web browser has been set to a proxy Go to Tools menu gt Internet Options gt Connections gt LAN Settings in the screen that appears cancel the Using Proxy checkbox and click OK to finish it After successfully log in you can click the Quick Setup menu to quickly configure your Router Quick Setup The quick setup will tell you how to configure
58. dd device button in Figure 4 31 49 TL WDR3600 BTU BITE SF Tave Meier lolimacelenccys then Figure 4 34 will appear Add A New Device Enter the new device s PIN Press the button of the new device in two minutes Figure 4 34 Add A New Device Step 2 Enter the PIN number from the client device in the field on the above WPS screen Then click Connect button Step 3 Connect successfully will appear on the screen of Figure 4 34 which means the client device has successfully connected to the Router lil Enter the Router s PIN on your client device Use this method if your client device asks for the Router s PIN number Step 1 On the client device enter the PIN number listed on the Router s Wi Fi Protected Setup screen shown in Figure 4 31 It is also labeled on the bottom of the Router Step 2 The Wi Fi Protected Setup LED flashes for two minutes during the Wi Fi Protected Setup process Step 3 When the WPS LED is on the client device has successfully connected to the Router Step 4 Refer back to your client device or its documentation for further instructions cs Note 1 The WPS LED on the Router will light green for five minutes if the device has been successfully added to the network 2 The WPS function cannot be configured if the Wireless Function of the Router is disabled Please make sure the Wireless Function is enabled before configuring the WPS 4 7 3 Wireless Security C
59. ddress 192 168 0 199 Address Lease Time 120 minutes 1 2880 minutes the default value is 120 Default Gateway optional Default Domain optional Primary DNS optional Secondary DNS optional SAYE Figure 4 44 DHCP Settings gt DHCP Server Enable or Disable the DHCP server If you disable the Server you must have another DHCP server within your network or else you must configure the computer manually gt Start IP Address Specify an IP address for the DHCP Server to start with when assigning IP addresses 192 168 0 100 is the default start address gt End IP Address Specify an IP address for the DHCP Server to end with when assigning IP addresses 192 168 0 199 is the default end address gt Address Lease Time The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address Enter the amount of time in minutes and the user will be leased this dynamic IP Address After the time is up the user will be automatically assigned a new dynamic IP address The range of the time is 1 2880 minutes The default value is 120 minutes gt Default Gateway Optional It is suggested to input the IP address of the Ethernet port of the Router The default value is 192 168 0 1 gt Default Domain Optional Input the domain name of your network gt Primary DNS Optional Input the DNS IP address provided by your ISP or consult your I
60. e Enable MAC Address IP Address Bind Modify 1 00 E0 4C 00 07 BE 192 168 0 4 Modify Delete Add NEw Enable All Disable All Delete All Current Mo Fage Figure 4 100 Binding Setting MAC Address The MAC address of the controlled computer in the LAN IP Address The assigned IP address of the controlled computer in the LAN Bind Check this option to enable ARP binding for a specific device Y Y V Y Modify To modify or delete an existing entry When you want to add or modify an IP amp MAC Binding entry you can click the Add New button or Modify button and then you will go to the next page This page is used for adding or modifying an IP amp MAC Binding entry shown in Figure 4 101 IP amp MAC Binding Settings MAC Address IP Address Back Figure 4 101 IP amp MAC Binding Setting Add amp Modify To add IP amp MAC Binding entries follow the steps below 1 Click the Add New button as shown in Figure 4 100 2 Enter the MAC Address and IP Address 3 Select the Bind checkbox 4 Click the Save button to save it To modify or delete an existing entry follow the steps below 1 Find the desired entry in the table 2 Click Modify or Delete as desired on the Modify column To find an existing entry follow the steps below 1 Click the Find button as shown in Figure 4 100 99 TL WDR3600 EA AAEE a ella vi 2 Enter the MAC Address or IP Address 3 Click the Find button in the
61. e 4 92 Static Routing To add static routing entries 1 Click Add New shown in Figure 4 92 you will see the following screen Add or Modify a Static Route Entry Destination Network Subnet Mask Default Gateway Status Figure 4 93 Add or Modify a Static Route Entry 2 Enter the following data gt Destination Network The Destination Network is the address of the network or host that you want to assign to a static route gt Subnet Mask The Subnet Mask determines which portion of an IP Address is the network portion and which portion is the host portion gt Default Gateway This is the IP Address of the gateway device that allows for contact between the Router and the network or host 3 Select Enabled or Disabled for this entry on the Status drop down list 4 Click the Save button to make the entry take effect Other configurations for the entries Click the Delete button to delete the entry 95 TL WDR3600 EI AAEE a MCT er lolimacelenccys Click the Enable All button to enable all the entries Click the Disable All button to disable all the entries Click the Delete All button to delete all the entries Click the Previous button to view the information in the previous screen click the Next button to view the information in the next screen 4 15 2 System Routing Table Choose menu Advanced Routing System Routing Table and then you can view the System Routing Table in the
62. e System Folder Figure 4 54 Media Server Setting 2 Click the Start button to start the media server and then the screen will appear as shown in Figure 4 55 Media Server Setting Server Name TP LINK_13098F Server Status Started C Auto scan every scan All Add share folder Hame File System Folder Figure 4 55 Media Server Setting 3 Click the Add share folder button to specify a folder as the search path of media server The screen will then appear as shown in Figure 4 56 65 TL WDR3600 BTU BTU a eile fF lolimacelenccys Add New Folder Partition Share entire partition Folder Location imy share Folder photo vided Figure 4 56 Add New Folder gt Display Name You can enter a display name for the share folder gt Share entire partition Choose this option and then the folders contained in this partition will all be shared gt Folder Location Displays the location of this folder gt Select Check the radio button to select the folder to share gt Folder Displays folders that are in current path gt Upper Click this button to get into the upper folder gt Save Click this button to save your settings and the page will be redirected to the media server configuration page gt Back Click this button to discard the settings and just go to the media server configuration page 4 Click the Scan All button to scan all the share folders immediately You can also sele
63. e sensitive For example TEST is NOT the same as fest Region Select your region from the drop down list This field specifies the region where the wireless function of the Router can be used It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field If your country or region is not listed please contact your local government agency for assistance When you select your local region from the drop down list click the Save button then the Note Dialog appears Click OK Microsoft Internet Explorer Note Dialog SP Note Limited by local law regulations version for North America does not have region selection option Mode Select the desired mode e 11b only Select if all of your wireless clients are 802 11b e 11g only Select if all of your wireless clients are 802 11g When 802 11g mode is selected only 802 11g wireless stations can connect to the Router e 11n only Select only if all of your wireless clients are 802 11n When 802 11n mode is selected only 802 11n wireless stations can connect to the Router eo 11bg mixed Select if you are using both 802 11b and 802 11g wireless clients e 11bgn mixed Select if you are using a mix of 802 11b 11g and 11n wireless clients It is strongly recommended that you set the Mode to 802 11bgn mixed and all of 802 11b 802 11g and 802 11n wireless stations can connect to the Router Channel Width
64. e the wireless channel unless you notice interference problems with another nearby access point Enable SSID Broadcast When wireless clients survey the local area for wireless networks to associate with they will detect the SSID broadcast by the Router If you select the Enable SSID Broadcast checkbox the Wireless Router will broadcast its name SSID on the air Enable WDS Bridging Check this box to enable WDS With this function the Router can bridge two or more Wlans If this checkbox is selected you will have to set the following parameters as shown in Figure 4 30 Make sure the following settings are correct SSID to be bridged BSSID to be bridged Example 00 10 OF 11 22 33 Key type WEP Index Auth type Password Figure 4 30 gt SSID to be bridged The SSID of the AP your Router is going to connect to as a client You can also use the search function to select the SSID to join 47 TL WDR3600 EAA AEAEE ETT Meier lolimacelenccys gt BSSID to be bridged The BSSID of the AP your Router is going to connect to as a client You can also use the search function to select the BSSID to join gt Survey Click this button you can search the AP which runs in the current channel gt Key type This option should be chosen according to the AP s security configuration It is recommended that the security type is the same as your AP s security type gt WEP Index This option should be c
65. ect another service and type the same IP address for that computer or server To modify or delete an existing entry 1 Find the desired entry in the table 2 Click Modify or Delete as desired on the Modify column Click the Enable Disabled All button to make all entries enabled disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and click the Previous button to return to the previous page Note If you set the service port of the virtual server as 80 you must set the Web management port on System Tools Remote Management page to be any other value except 80 such as 8080 Otherwise there will be a conflict to disable the virtual server 4 11 2 Port Triggering Choose menu Forwarding Port Triggering you can view and add port triggering in the next screen shown in Figure 4 64 Some applications require multiple connections like Internet games video conferencing Internet telephoning and so on Port Triggering is used for some of these applications that cannot work with a pure NAT Router arie TL WDR3600 EA AAEE a ella vi Port Triggering ID Trigger Port Trigger Protocol Incoming Port Incoming Protocol Status Modify 1 554 ALL 8970 8999 ALL Enabled Modify Delete Add Mew Enable All Disable All Delete All Figure 4 64 Port Triggering To add a new rule follow the steps below 1 Click the Add New button the next screen will pop up as sho
66. ed or 5 ASCII characters 128 bit You can enter 26 hexadecimal digits any combination of 0 9 a f A F zero key is not promoted or 13 ASCII characters 152 bit You can enter 32 hexadecimal digits any combination of 0 9 a f A F zero key is not promoted or 16 ASCII characters cs Note If you do not set the key the wireless security function is still disabled even if you have selected Shared Key as Authentication Type Be sure to click the Save button to save your settings on this page 4 7 4 Wireless MAC Filtering Choose menu Wireless MAC Filtering you can control the wireless access by configuring the Wireless MAC Filtering function shown in Figure 4 24 53 TL WDR3600 MYC BITE SE Tave Meier lolimacelenccys Wireless MAC Filtering Wireless MAC Filtering Disabled Filtering Rules Deny the stations specified by any enabled entries in the listto access Allow the stations specified by any enabled entries in the listto access ID MAC Address Status Description Modify 1 00 0A EB B0 00 0B Enabled Wireless station A Modify Delete Add New Enable All Disable All Delete All Figure 4 39 Wireless MAC Filtering To filter wireless users by MAC Address click Enable The default setting is Disabled gt MAC Address The wireless station s MAC address that you want to filter gt Status The status of this entry either Enabled or Disabled gt Description A simple description of t
67. eeeseeesaes 19 4 139 Parental Dl 80 Ae TAY ACCESS COMMU Ol kefre as o cial 83 A arden haeh a 83 a NA a OE A ET A eeae enced Cae T E S E E T nea Seannerenls 89 E E aa E E E E EA 90 ANA A E A A 92 415 Advanced OU 94 ATON Statie ROMINO LIS ereire nn ONE 95 A t9 2 gt VStem Rounng Table rreren ie te e acne 96 AAG Bana wiGtt CONTO as A nec teense eee een 96 416 1 Control Sets Sesent ccc enide ideas ete hdtiace Sees eek A 97 416 2 Rules LIS ot A O o tess coaeiaa Macdeaaetbheeneheeetaieae rte 97 ATT PS MAC Bindang Seting is a tod alas salte o sie 98 AST 21 BiNGING SEtUNG Seesen en caceria 98 A e nl ee 100 410 DyNamMme DN 0 O 5 ee eee ee 101 4 181 COMexe c DON Sa A eee 101 418 2 Dyndns Org DDNS x6 iS ta 102 418 3 INO IP COMMDDIN Stan io a 103 ANO System TOS id a a od cts nro le pa en a endo 104 AA OST TIME CUINA ica 104 AZ DANOS ui A ta ode 106 4 19 39 ElMmwale Upgrade stas orde 107 4 194 Factory DelalllS srren lolis 108 A195 BACK Gc RESO eri 109 AS A A ee te ear 110 ATIT O eoria 110 ATE OVSE A A a sce bast 111 AS DUAL SUCS oea a a a od 113 Appendix A FAQ eiie 115 Appendix B Configuring the PCS cooccccncccccocccocccncnonaconanonnnnnnnnnnonarennrennrnnnrnannnnn 120 Appendix C Specifications isis 123 Appendix D GlIOSS BUY ai 124 TL WDR3600 EA AAEE a ella vi Package Contents The following items should be found in your package TL WDR3600 N600 Wireless Dual Band Gigabit Router DC Power
68. eier lolimacelenccys e 11b only Select if all of your wireless clients are 802 11b e 11g only Select if all of your wireless clients are 802 11g e 11n only Select only if all of your wireless clients are 802 11n eo 11bg mixed Select if you are using both 802 11b and 802 11g wireless clients e 11bgn mixed Select if you are using a mix of 802 11b 11g and 11n wireless clients gt Channel Width Select any channel width from the drop down list The default setting is Auto which can adjust the channel width for your clients automatically gt Channel This field determines which operating frequency will be used It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point If you select Auto then the AP will select the best channel automatically gt Wireless Security Disable Security The wireless security function can be enabled or disabled If disabled the wireless stations will be able to connect the Router without encryption eo Enable Security WPA PSK WPA2 PSK It s selected by default with the default PSK password the same as the default PIN code e No Change If you chose this option wireless security configuration will not change These settings are only for basic wireless parameters For advanced settings please refer to 4 6 Wireless 2 4GHz Configure the basic parameters for 5GHz wireless network in the fo
69. ency for assistance When you select your local region from the drop down list click the Save button then the Note Dialog appears Click OK Microsoft Internet Explorer Note Dialog 46 TL WDR3600 EA AAEE a MCT er lolimacelenccys cs Note Limited by local law regulations version for North America does not have region selection option Mode Select the desired mode e 11a only Select if all of your wireless clients are 802 11a When 802 11a mode is selected only 802 11a wireless stations can connect to the Router e 11n only Select only if all of your wireless clients are 802 11n When 802 11n mode is selected only 802 11n wireless stations can connect to the Router eo 11an mixed Select if you are using both 802 11a and 802 11n wireless clients It is strongly recommended that you set the Mode 11an mixed and all of 802 11a and 802 11n wireless stations can connect to the Router Channel width Select the channel width from the drop down list The default setting is automatic which can adjust the channel width for your clients automatically cs Note If 11a only is selected in the Mode field the Channel Width selecting field will turn grey and the value will become 20M which is unable to be changed Channel This field determines which operating frequency will be used The default channel is set to Auto so the Router will choose the best channel automatically It is not necessary to chang
70. er has a system error Off The wireless The wireless function is disabled The wireless function is disabled disabled Wireless 2 4GHz Flashin car wireless function is enabled The Router is working on 9 2 4GHz radio band Of The wireless function is disabled gt Wireless 5GHZ The wireless function is enabled The Router is working on MARMING 5GHz radio band There is no device linked to the corresponding port GJ Ethernet On There is a device linked to the corresponding port but there amp Internet is no activity Flashing There is an active device linked to the corresponding port TL WDR3600 BY BITE SF Tale RCIE o vi Slow A wireless device is connecting to the network by WPS Flash function This process will last in the first 2 minutes A wireless device has been successfully added to the 5 a network by WPS function Quick A wireless device failed to be added to the network by WPS Flash function USB on the No storage device or printer is plugged into the USB port fear pane A storage device or printer has connected to the USB port Table 1 1 The LEDs Description CF Note 1 After a device is successfully added to the network by WPS function the WPS LED will keep on for about 5 minutes and then turn off 2 The Router is set to working concurrently in 2 4GHz and 5GHz by default If you desire to choose the working frequency please go to 4 5 Dual Band Selecti
71. er lolimacelenccys Chapter 2 Connecting the Router 2 1 System Requirements gt Broadband Internet Access Service DSL Cable Ethernet gt One DSL Cable Modem that has an RJ45 connector which is not necessary if the Router is connected directly to the Ethernet gt PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors gt TCP IP protocol on each PC gt Web browser such as Microsoft Internet Explorer Mozilla Firefox or Apple Safari 2 2 Installation Environment Requirements gt Place the Router in a well ventilated place far from any heater or heating vent gt Avoid direct irradiation of any strong light such as sunlight gt Keep at least 2 inches 5 cm of clear space around the Router gt Operating Temperature 0 C 40 C 32 F 104 F gt Operating Humidity 10 90 RH Non condensing 2 3 Connecting the Router Before installing the Router make sure your PC is connected to the Internet through the broadband service successfully If there is any problem please contact your ISP After that please install the Router according to the following steps Don t forget to pull out the power plug and keep your hands dry 1 Power off your Cable DSL Modem and the Router 2 Locate an optimum location for the Router The best place is usually at the center of your wireless network 3 Adjust the direction of the antenna Normally upright is a good direction 4 Connect the DSL Cable Modem t
72. ersion Encryption TKIP hal Radius Server Pf Radius Port 1812 1 65535 0 stands for default pon 1812 Group Key Update Period pa fin second minimum is 30 0 means no update We do notrecormnend using the TKIP encreption ifthe device operates in 202 11n mode due to the fact that TKIP is not supported by 802 11n specification Figure 4 22 WPA WPAZ2 Enterprise e Radius Server IP Enter the IP address of the Radius server e Radius Port Enter the port number of the Radius server e Radius Password Enter the password for the Radius server e Group Key Update Period Specify the group key update interval in seconds The value should be 30 or above Enter 0 to disable the update WEP It is based on the IEEE 802 11 standard If you check this radio button you will find a notice in red as show in Figure 4 23 40 TL WDR3600 BCT ee BTU ETT RIEL ao i WEP Key Format Hexadecimal Key Selected WEP Key Password Key Type Ko peg We do not recommend using the WEP encryption ifthe device operates in 802 1719 mode due to the fact that YEP is not supported by 802 11n specification Figure 4 23 WEP e Type you can choose the type for the WEP security on the drop down list The default setting is Automatic which can select Shared Key or Open System authentication type automatically based on the wireless station s capability and request e WEP Key Format Hexadecimal and ASCII formats a
73. es e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This device and its antenna must not be co located or operating in conjunction with any other antenna or transmitter To comply with FCC RF exposure compliance requirements this grant is applicable to only Mobile Configurations The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in c
74. es the shared or non shared status of the volume When the volume is shared you can click the Disable to stop sharing the volume when volume is non shared you can click the Enable button to share the volume Click the Start button to start the Network Sharing service Click the Stop button to stop the Network Sharing service Click the Eject Disk button to safely remove the USB storage device that is connected to USB port This takes the drive offline A message as shown in Figure 4 50 will appear on your web browser when it is safe to detach the USB disk 61 TL WDR3600 AAEE a ella o vi Microsoft Internet Explorer A The disk can be physically unplugged from the Router now Oox Figure 4 50 Safe Unplug Message Click the Rescan button to start a new scan Follow the instructions below to set up your Router as a file server 1 Plug an external USB hard disk drive or USB flash drive into this Router 2 Click the Rescan button to find the USB drive that has been attached to the Router Click the Start button to start the Storage Sharing service 9 Click the Enable button under Shared to enable the disk to share 5 Click the Open the disk to visit the sharing disk cS Note 1 The Router can automatically locate new USB drive But to display the information about your USB device you need to click the Rescan button manually 2 The new settings will not take effect until you restart the service 3 To unp
75. ess Control Advanced Routing Bandwidth Control IP amp MAC Binding Dynamic DHS system Tools The detailed explanations for each Web page s key function are listed below 4 2 Status The Status page provides the current status information about the Router All information is read only 19 Status Firmware Version Hardware Version LAN MAC Address IP Address Subnet Mask Wireless 2 4GHz Wireless Radio Name SSID Mode Channel Channel Width MAC Address WDS Status Wireless 5GHz Wireless Radio Hame SSID Mode Channel Channel Width MAC Address WDS Status WAN MAC Address IP Address Subnet Mask Default Gateway DNS Server Traffic Statistics Bytes Packets System Up Time TL WDR3600 N600 Wireless Dual Band Gigabit Router 3 13 17 Build 120508 Rel 455954n WDOR3600 v1 00000000 D8 SD 40 1 0 FF 2F 192 168 0 1 255 455 255 0 Enable TP LINK_ 2 4GHz_10FF2E Tibgn mixed Auto Current channel 6 Automatic D8 5D 4C 10 FF 2E Disable Enable TP LINK_SGHz_10FF2F 11an mixed Auto Current channel 36 Automatic D8 50 40 10 FF 2F Disable D8 5D 40 10 FF 30 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Received 0 0 O days 06 10 02 Dynamic IP Renew Sent 6651 89 Figure 4 1 Router Status 90 lt TL WDR3600 EJ AAEE a Meier lelimacelenccys 4 3 Quick Setup Please refer to 3 2 Quick Installation Guide 4 4 Network Net
76. ess Statistics Figure 4 28 Wireless menu 45 TL WDR3600 EAA AEAEE ETT Meier lolimacelenccys There are five submenus under the Wireless menu shown in Figure 4 13 Wireless Settings WPS Wireless Security Wireless MAC Filtering Wireless Advanced and Wireless Statistics Click any of them and you will be able to configure the corresponding function 4 7 1 Wireless Settings Choose menu Wireless 5GHz Wireless Settings you can configure the basic settings for the wireless network of 5GHz on this page Wireless Settings GHZ Wireless Network Name TP LIMNK S GHz_13098F Also called the SSID Mode Channel Width Enable SSID Broadcast C Enable WDS Bridging SAVE Figure 4 29 Wireless Settings 5GHz gt Wireless Network Name Also called the SSID Service Set Identification Enter a value of up to 32 characters The same name must be assigned to all wireless devices in your network Considering your wireless network security the default SSID is set to be TP LINK_5GHz_XXXXXX This value is case sensitive For example TEST is NOT the same as fest gt Region Select your region from the drop down list This field specifies the region where the wireless function of the Router can be used It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field If your country or region is not listed please contact your local government ag
77. et value the Router will startup the blocking function immediately gt Enable UDP FLOOD Filtering Enable or Disable the UDP FLOOD Filtering gt UDP FLOOD Packets Threshold 5 3600 The default value is 500 Enter a value between 5 3600 When the current UPD FLOOD Packets number is beyond the set value the Router will startup the blocking function immediately gt Enable TCP SYN FLOOD Attack Filtering Enable or Disable the TCP SYN FLOOD Attack Filtering gt TCP SYN FLOOD Packets Threshold 5 3600 The default value is 50 Enter a value between 5 3600 When the current TCP SYN FLOOD Packets numbers is beyond the set value the Router will startup the blocking function immediately gt Ignore Ping Packet From WAN Port Enable or Disable Ignore Ping Packet From WAN Port The default setting is disabled If enabled the ping packet from the Internet cannot access the Router gt Forbid Ping Packet From LAN Port Enable or Disable Forbid Ping Packet From LAN Port The default setting is disabled If enabled the ping packet from LAN cannot access the Router This function can be used to defend against some viruses Click the Save button to save the settings Click the Blocked DoS Host List button to display the DoS host table by blocking 4 12 3 Local Management Choose menu Security Local Management and then you can configure the management rule in the screen as shown in Figure 4 71 The management
78. f Dynamic Static IP to activate this secondary connection e Disabled The Secondary Connection is disabled by default so there is PPPoE connection only This is recommended e Dynamic IP You can check this radio button to use Dynamic IP as the secondary IS TL WDR3600 Bye ele Ele Rel Leti connection to connect to the local area network provided by ISP e Static IP You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP gt Connect on Demand In this mode the Internet connection can be terminated automatically after a specified inactivity period Max Idle Time and be re established when you attempt to access the Internet again If you want your Internet connection keeps active all the time please enter 0 in the Max Idle Time field Otherwise enter the number of minutes you want to have elapsed before your Internet access disconnects gt Connect Automatically The connection can be re established automatically when it was down gt Time based Connecting The connection will only be established in the period from the start time to the end time both are in HH MM format Ss Note Only when you have configured the system time on System Tools Time Settings page will the Time based Connecting function can take effect gt Connect Manually You can click the Connect Disconnect button to connect disconnect immediately
79. fF Note If you are not familiar with the setting items in this page it s strongly recommended to keep the provided default values otherwise it may result in lower wireless network performance 4 6 6 Wireless Statistics Choose menu Wireless 2 4GHz Wireless Statistics you can see the MAC Address Current Status Received Packets and Sent Packets for each connected wireless station Wireless Statistics Current Connected Wireless Stations numbers 1 ID MAC Address Current Status Received Packets sent Packets 1 00 04 FEB 88 34 75 STA A5S50C 416 2 Previous Figure 4 27 Wireless Statistics gt MAC Address The connected wireless station s MAC address gt Current Status The connected wireless station s running status one of STA AUTH STA ASSOC STA JOINED WPA WPA PSK WPA2 WPA2 PSK AP UP AP DOWN Disconnected gt Received Packets Packets received by the station gt Sent Packets Packets sent by the station You cannot change any of the values on this page To update this page and to show the current connected wireless stations click on the Refresh button If the numbers of connected wireless stations go beyond one page click the Next button to go to the next page and click the Previous button to return the previous page fF Note This page will be refreshed automatically every 5 seconds 4 7 Wireless 5GHz WPS Wireless Security Wireless MAC Filtering Wireless Advanced Wirel
80. factory default user name and password of the Router because all users who try to access the Router s Web based utility or Quick Setup 110 TL WDR3600 BTU BITE SF Tave Meier lolimacelenccys will be prompted for the Router s default user name and password The new user name and password must not exceed 14 characters in length and not include any spaces Enter the new Password twice to confirm it Click the Save button when finished Click the Clear All button to clear all 4 19 8 System Log Choose menu System Tools System Log and then you can view the logs of the Router system Log Auto Mail Feature Disabled Mail Settings Log Type ALL Log Level ALL Log is Empty Time 1970 01 01 6 24 23 230645 H Wer WDR3600 v1 00000000 Ver 3 13 17 Build 120508 Rel 45884n L 192 168 0 1 M 255 255 255 0 Wl DHCP Y 0 0 0 0 M 0 0 0 0 G 0 0 0 0 Mail Log Current Mo E Page Figure 4 117 System Log gt Auto Mail Feature Indicates whether auto mail feature is enabled or not gt Mail Settings Set the receiving and sending mailbox address server address validation information as well as the timetable for Auto Mail Feature as shown in Figure 4 118 111 TL WDR3600 EJAAN a Meier lolimacelenccys Mail Account Settings To SMTP Server F Authentication O Enable Auto Mail Feature Everyday mail the log at Mail t
81. feature allows you to deny computers in LAN from accessing the Router 78 TL WDR3600 BYU BTU ETT ella o vi Local Management Management Rules Allthe PCs on the LAN are allowed to access the Routers Web Based Utility O Only the PCs listed can browse the builtin web pages to perform Administrator tasks MAC 1 MAC 2 MAC 3 MAC 4 Your PC s MAC Address Figure 4 71 Local Management By default the radio button All the PCs on the LAN are allowed to access the Router s Web Based Utility is checked If you want to allow PCs with specific MAC Addresses to access the Setup page of the Router s Web Based Utility locally from inside the network check the radio button Only the PCs listed can browse the built in web pages to perform Administrator tasks and then enter each MAC Address in a separate field The format for the MAC Address is XX XX XX XX XX XXK X is any hexadecimal digit Only the PCs with MAC address listed can use the password to browse the built in web pages to perform Administrator tasks while all the others will be blocked After click the Add button your PC s MAC Address will be placed in the list above Click the Save button to save your settings E Note If your PC is blocked but you want to access the Router again use a pin to press and hold the Reset Button hole on the back panel for about 5 seconds to reset the Router s factory defaults on the Router s Web Based Utility
82. from the drop down list for the rule The default value is the Target Description you set just now gt Schedule In this field select a schedule from the drop down list for the rule The default value is the Schedule Description you set just now gt Status In this field there are two options Enable or Disable Select Enable so that the rule will take effect Select Disable so that the rule won t take effect 5 Click Finish to complete adding a new rule Method Two 1 Click the Add New button and the next screen will pop up as shown in Figure 4 82 2 Give a name e g Rule_1 for the rule in the Rule Name field 3 Select a host from the Host drop down list or choose Click Here To Add New Host List 4 Select a target from the Target drop sown list or choose Click Here To Add New Target List 8 s TL WDR3600 EAA AEAEE ETT eile rlolimacelenccys Select a schedule from the Schedule drop down list or choose Click Here To Add New Schedule In the Status field select Enabled or Disabled to enable or disable your entry Click the Save button Add Internet Access Control Entry Rule Name Host Click Here To Add New Host List Target Any Target Glick Here To Add New Target List Schedule Click Here To Add New Schedule Status Enabled Figure 4 82 Add Internet Access Control Entry For example If you desire to allow the host with MAC address 00 11 22 33 44 AA to access www google com only
83. h is displayed on the Status page 4 How to enable DMZ Host Log in to the Router click the Forwarding menu on the left of your browser and click DMZ submenu On the DMZ page click Enable radio button and type your IP address into the DMZ Host IP Address field using 192 168 0 169 as an example remember to click the Save button Current DMZ Status Enable Disable DMZ Host IP Address 192 168 0 7169 nave Figure A 6 DMZ 5 How to enable H323 ALG Log in to the Router click the Security menu on the left of your browser and click Basic Security submenu On the Basic Security page check the Enable radio button next to H323 ALG Remember to click the Save button 117 TL WDR3600 BCT ee BTU SF Tave elit Basic Security Firewall SPI Firewall Enable Disable PPTP Passthrough Enable Disable L2TP Passthrough Enable Disable IPSec Passthrough Enable Disable FTP ALG Enable Disable TFTP ALG Enable Disable H323 ALG Enable Y RTSP ALG Enable Disable DAYE Figure A 7 Basic Security want to build a WEB Server on the LAN what should I do 1 Because the WEB Server port 80 will interfere with the WEB management port 80 on the Router you must change the WEB management port number to avoid interference 2 To change the WEB management port number Log in to the Router click the Security menu on the
84. h this device The required antenna impedance is 50 ohms To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that permitted for successful communication Industry Canada Statement This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body Ce dispositif est conforme a la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 Le dispositif ne doit pas produire de brouillage pr judiciable et 2 Ce dispositif doit accepter tout brouillage recu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable NOTE IMPORTANTE D claration d exposition aux radiations Cet quipement est conforme aux limites d exposition aux rayonnements IC tablies pour un environnement non contr l Cet quipement doit tre
85. has read only access to Storage Sharing and can not access FTP Server User Account Management Add New User Password Storage Authority FTP Access Modify admin Read and Write yes Edit Delete quest Read Only no dit Delete Figure 4 58 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB drive To add a new user account please follow the steps below 1 Click Add New User button and the screen will appear as shown in Figure 4 59 2 Self define a User Name 3 Enter the password in the Password field oe 4 5 6 TL WDR3600 EA AAEE a MCT erlolimacelenccys Re enter the password in the Confirm Password field Choose the Storage Authority from the drop down list Read and Write or Read Only Choose FTP Access from the drop down list Yes or No Add or Modify User Account User Name quest2 Password Confirm Password Storage Authority Read Only wt FTP Access Figure 4 59 Add or Modify User Account User Name Type the user name that you want to give access to the USB drive The user name must be composed of alphanumeric symbols not exceeding 15 characters in length Password Enter the password in the Password field The password must be composed of alphanumeric symbols not exceeding 15 characters in length For security purposes the password for each user account is not displayed Confirm Password Re enter the
86. he log every hours Figure 4 118 Mail Account Settings eo From Your mail box address The Router would connect it to send logs To Recipient s address The destination mailbox where the logs would be received o SMTP Server Your smtp server It corresponds with the mailbox filled in the From field You can log on the relevant website for help if you are not clear with the address e Authentication Most SMTP Server requires Authentication It is required by most mailboxes that need User Name and Password to log in ce Note Only when you select Authentication do you have to enter the User Name and Password in the following fields o User Name Your mail account name filled in the From field The part behind is excluded eo Password Your mail account password e Confirm The Password Enter the password again to confirm e Enable Auto Mail Feature Select it to mail logs automatically You could mail the current logs either at a specified time everyday or by intervals but only one could be the current effective rule Enter the desired time or intervals in the corresponding field as shown in Figure 4 118 Click Save to keep your settings Click Back to return to the previous page gt Log Type By selecting the log type only logs of this type will be shown gt Log Level By selecting the log level only logs of this level will be shown gt Refresh Refresh the page to show the latest log list 112
87. he same with the default PIN code which is labeled on the bottom of the Router or can be found in Figure 4 31 Group Key Update Period Specify the group key update interval in seconds The value should be 30 or above Enter 0 to disable the update WPA WPA2 Enterprise Its based on Radius Server Version you can choose the version of the WPA security on the drop down list The default setting is Automatic which can select WPA Wi Fi Protected Access or WPA2 WPA version 2 automatically based on the wireless station s capability and request Encryption You can select either Automatic or TKIP or AES f Note If you check the WPA WPA2 Enterprise radio button and choose TKIP encryption you will find a notice in red as shown in Figure 4 37 WPAWPA2 Enterprise Version Encryption TKIP le Radius Server IP San Radius Port 1812 1 65535 0 stands for default pon 1812 Group Key Update Period o fin second minimum is 30 0 means no update We do notrecommend using the TKIP encrption ifthe device operates in 202 11n mode due to the fact that TKIP is not supported by 802 11n specification Figure 4 37 WPA WPA2 Enterprise Radius Server IP Enter the IP address of the Radius server Radius Port Enter the port number of the Radius server Radius Password Enter the password for the Radius server Group Key Update Period Specify the group key update interval in seconds The value should be 30
88. he wireless station To Add a Wireless MAC Address filtering entry click the Add New button The Add or Modify Wireless MAC Address Filtering entry page will appear shown in Figure 4 25 Add or Modify Wireless MAC Address Filtering entry Status Enabled w Figure 4 40 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry follow these instructions 1 Enter the appropriate MAC Address into the MAC Address field The format of the MAC Address iS XX XX XX XX XX XX X is any hexadecimal digit For example 00 OA EB B0 00 06B 2 Give a simple description for the wireless station in the Description field For example Wireless station A 3 Select Enabled or Disabled for this entry on the Status drop down list 4 Click the Save button to save this entry To modify or delete an existing entry 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete 54 TL WDR3600 BCT ee BTU ETT MCT erlolimacelenccys 2 Modify the information 3 Click the Save button Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled Click the Delete All button to delete all entries Click the Next button to go to the next page Click the Previous button to return to the previous page For example If you desire that the wireless station A with MAC address 00 OA EB BO 00 0B and the w
89. hedule is based on the time of the Router Schedule Description SS Day Everyday Select Days Mon Tue Wed Thu Fri sal Time all day 24 hours Start Time HHMI Stop Time HHMM Figure 4 80 Quick Setup Create an Advanced Schedule Entry Schedule Description In this field create a description for the schedule Note that this description should be unique e g Schedule_ 1 Day Choose Select Days and select the certain day days or choose Everyday Time Select 24 hours or specify the Start Time and Stop Time yourself 86 TL WDR3600 EAA AEAEE ETT Meier lolimacelenccys gt Start Time Enter the start time in HHMM format HHMM are 4 numbers For example 0800 is 8 00 gt Stop Time Enter the stop time in HHMM format HHMM are 4 numbers For example 2000 is 20 00 4 Click Next when finishing creating the advanced schedule entry and the next screen will appear as shown in Figure 4 81 Quick Setup Create an Internet Access Control Entry Rule Name Host Host 1 Target Target_1 aa Schedule Schedule 1 Status Enabled Finish Figure 4 81 Quick Setup Create an Internet Access Control Entry gt Rule In this field create a name for the rule Note that this name should be unique e g Rule 1 gt Host In this field select a host from the drop down list for the rule The default value is the Host Description you set just now gt Target In this filed select a target
90. hoose menu Wireless 5GHz Wireless Security you can configure the security settings of your wireless network There are five wireless security modes supported by the Router WPA Personal WPA2 Personal WPA Enterprise WPA2 Enterprise and WEP BO Wireless Security Disable Security TL WDR3600 N600 Wireless Dual Band Gigabit Router WPA WPA2 Personal Recommended Version Encryption PSK Password Group Key Update Period WPA WPA2 Enterprise Version Encryption Radius Server IP Radius Port Radius Password Group Key Update Period WEP Type WEP Key Format Key Selected Key 1 Key 2 Key 3 Key 4 Automatic Recommended Y AES J 12345670 You can enter ASCII characters between 8 and 63 or Hexadecimal characters between 8 and 64 0 Seconds Keep it default if you are not sure minimum is 30 O means no update Automatic y Automatic xj 1812 1 65535 0 stands for default port 1812 in second minimum is 30 O means no update Automatic v Hexadecimal v WEP Key Password Key Type Disabled Disabled Disabled Disabled Save Figure 4 35 Wireless Security Disable Security If you do not want to use wireless security check this radio button But it s strongly recommended to choose one of the fo
91. hosen if the key type is WEP ASCII or WEP HEX It indicates the index of the WEP key gt Auth Type This option should be chosen if the key type is WEP ASCII or WEP HEX It indicates the authorization type of the Root AP gt Password If the AP your Router is going to connect needs password you need to fill the password in this blank 4 7 2 WPS Choose menu Wireless 5GHz WPS you can the screen as shown in Figure 4 31 This section will guide you to add a new wireless device to an existing network quickly by WPS Wi Fi Protected Setup function WPS Wi Fi Protected Setup WPS Status Enabled Disable WPS Current PIN 12345670 Restore PIN Gen New PIN Disable Routers PIM Add anew device Add device Figure 4 31 WPS gt WPS Status Enable or disable the WPS function here gt Current PIN The current value of the Router s PIN is displayed here The default PIN of the Router can be found in the label or User Guide gt Restore PIN Restore the PIN of the Router to its default gt Gen New PIN Click this button and then you can get a new random value for the Router s PIN You can ensure the network security by generating a new PIN gt Add device You can add a new device to the existing network manually by clicking this button 48 TL WDR3600 EA AAEE ETT Meier lolimacelenccys If the wireless adapter supports Wi Fi Protected Setup WPS you can establish a wireless co
92. ically Time based Connecting Period of Time from o a HH Mnf to 23 59 HH MM O Connect Manually hax Idle Time 15 minutes 0 means remain active at all times Disconnected Figure A 2 PPPoE Connection Mode E Note 1 Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time since some applications is visiting the Internet continually in the background 2 If you are a Cable user please configure the Router following the above steps 115 TL WDR3600 Bye leet TR Sy Tale Rel evi 2 How dol configure the Router to access Internet by Ethernet users 1 Login to the Router click the Network menu on the left of your browser and click WAN submenu On the WAN page select Dynamic IP for WAN Connection Type finish by clicking Save Some ISPs require that you register the MAC Address of your adapter which is connected to your cable DSL Modem during installation If your ISP requires MAC register login to the Router and click the Network menu link on the left of your browser and then click MAC Clone submenu link On the MAC Clone page if your PC s MAC address is proper MAC address click the Clone MAC Address button and your PC s MAC address will fill in the WAN MAC Address field Or else type the MAC Address into the WAN MAC Address field The format for the MAC Address is XX XX XX XX XX XX Then click the Save butt
93. ime Setting and then you can configure the time on the following screen Time Settings Time zone GMT 08 00 Beijing Hong Kong Perth Singapore Time e HHIMMISS HTP Server i DOD Optional HTP Server ll DO Optional Get GMT Enable Daylight Saving Start Wlar ar Sun Zam End Navy ne Sun Jam Daylight Saving Status daylight saving is down Mote Click the GET GMT to Update the time from the internet with the pre defined servers or entering the customized serverdP Address or Domain Mame in the above frames Figure 4 108 Time settings 104 Vv Vv V WV gt TL WDR3600 MCU ee BIUE a Meier lolimacelenccys Time Zone Select your local time zone from this pull down list Date Enter your local date in MM DD YY into the right blanks Time Enter your local time in HH MM SS into the right blanks NTP Server NTP Server Il Enter the address or domain of the NTP Server or NTP Server Il and then the Router will get the time from the NTP Server preferentially In addition the Router built in some common NTP Servers so it can get time automatically once it connects the Internet Enable Daylight Saving Check the box to enable the Daylight Saving function Start The time to start the Daylight Saving Select the month in the first field the week in the second field the day in the third field and the time in the last field End The time to end the Daylight Saving Select the
94. ireless station B with MAC address 00 OA EB 00 07 5F are able to access the Router but all the other wireless stations cannot access the Router you can configure the Wireless MAC Address Filtering list by following these steps 1 Click the Enable button to enable this function 2 Select the radio button Allow the entries specified by any enabled entries in the list to access for Filtering Rules a Delete all or disable all entries if there are any entries already gt Click the Add New button Enter the MAC address 00 0A EB B0 00 0B 00 0A EB 00 07 5F in the MAC Address field 6 Enter wireless station A B in the Description field 7 Select Enabled in the Status drop down list 8 Click the Save button 9 Click the Back button The filtering rules that configured should be similar to the following list Filtering Rules Deny the stations specified by any enabled entries in the listto access Allow the stations specified by any enabled entries in the listto access ID MAC Address Status Description Modify 1 00 0A EB B0 00 0B Enabled wireless station A Modify Delete 2 00 04 EB 00 07 5F Enabled wireless station B Modify Delete 4 7 5 Wireless Advanced Choose menu Wireless Wireless Advanced you can configure the advanced settings of your wireless network 55 TL WDR3600 EJ AAEE a Meier lolimacelenccys Wireless Advanced Transmit Power High v Beacon Interval 100 Y 40
95. ited by local law regulations version for North America does not have region selection option gt Band This field displayed the operating frequency being configured gt Mode This field determines the wireless mode which the Router works on e 11a only Select if all of your wireless clients are 802 11a e 11n only Select only if all of your wireless clients are 802 11n o 11an mixed Select if you are using both 802 11a and 802 11n wireless clients gt Channel Width Select any channel width from the drop down list The default setting is Auto which can adjust the channel width for your clients automatically 47 TL WDR3600 EIA BTU SF Tave MCT er lolimacelenccys gt Channel This field determines which operating frequency will be used It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point If you select Auto then the AP will select the best channel automatically gt Wireless Security Disable Security The wireless security function can be enabled or disabled If disabled the wireless stations will be able to connect the Router without encryption eo Enable Security WPA PSK WPA2 PSK It s selected by default with the default PSK password the same as the default PIN code e No Change If you chose this option wireless security configuration will not change These settings are only for basic wireless p
96. ith Schedule Description is Schedule _1 Day is Sat and Time is all day 24 hours 3 Click Parental Control menu on the left to go back to the Add or Modify Parental Control Entry page 1 Click Add New button 2 Enter 00 11 22 33 44 AA in the MAC Address of Child PC field 3 Enter Allow Google in the Website Description field 4 Enter www google com in the Allowed Domain Name field 5 Select Schedule 1 you create just now from the Effective Time drop down list 6 In Status field select Enable 4 Click Save to complete the settings Then you will go back to the Parental Control Settings page and see the following list as shown in Figure 4 75 ID MAC address Website Description Schedule Enable Modify 1 00 11 22 33 44 AA Allow Google Schedule_1 Edit Delete Add New Enable All Disable All Delete All Figure 4 75 Parental Control Settings 4 14 Access Control Access Control There are four submenus under the Access Control menu as shown in Figure 4 76 Rule Host Target and Schedule Click any of them and you will be able to configure the corresponding function 4 14 1 Rule Choose menu Access Control Rule and then you can view and set Access Control rules in the screen as shown in Figure 4 77 83 Vv Vv V V WV Vv Vv Y VW WV VY Yy TL WDR3600 BCT IU ETT RCIE ot Access Control Rule Management C Enable Internet Access Control Default Filter Policy
97. k Setup MAC Clone MAC Clone is necessary for most users using Cable Modern It s highly recommended to do this on the MAIN COMPUTER that was originally connected to your Cable Modem Ifyou are unsure please select YES For more information please read the HELP section on the right Yes am using cable modem and connected by the main computer clone MAC address No lam using non cable modem service do NOT clone MAC address Mote Itis strongly recommended to restart the Cable Modern after the Quick Setup is done This important operation will solve mostissues Figure 3 8 Quick Setup MAC Clone gt Ifyou are visiting the Router from the main computer please select Yes and then click Next gt If you are visiting the Router from another computer rather than the main computer please select No and then click Next Cf Note 1 It s strongly recommended that you visit and configure the Router from the main computer 2 To find the main computer s MAC please go to Start gt Run on your main computer type in cmd and press Enter At the command prompt enter ipconfig all and press Enter The MAC will be displayed as Physical Address shown in Figure 3 9 ca CAOWINDOWS is ystem3 2 temd exe Microsoft Windows HP Version 5 1 2600 CG Copyright 1985 26081 Microsoft Corp C Documents and Settings english gt ipconfig all Windows IP Configuration Host Hame tpidea 1B0272d Primary Dns Suffix z Hode
98. l name or the keywords e g google in the Allowed Domain Name field Any domain name with keywords in it www google com www google com hk will be allowed Select from the Effective Time drop down list the schedule e g Schedule_1 you want If there are not suitable schedules for you click the Schedule in red below to go to the Advance Schedule Settings page and create the schedule you need In the Status field you can select Enabled or Disabled to enable or disable your entry Click the Save button Click the Enable All button to enable all the rules in the list Click the Disable All button to disable all the rules in the list Click the Delete All button to delete all the entries in the table Click the Next button to go to the next page or click the Previous button to return to the previous page For example If you desire that the child PC with MAC address 00 11 22 33 44 AA can access www google com on Saturday only while the parent PC with MAC address 00 11 22 33 44 BB is without any restriction you should follow the settings below 1 Click Parental Control menu on the left to enter the Parental Control Settings page Check Enable and enter the MAC address 00 11 22 33 44 BB in the MAC Address of Parental PC field 82 TL WDR3600 BCT eee BIUE a RCIE o vi 2 Click Access Control Schedule on the left to enter the Schedule Settings page Click Add New button to create a new schedule w
99. le 2000 2038 2046 2050 2051 2085 3010 3030 gt Incoming Protocol The protocol used for Incoming Port either TCP UDP or ALL all protocols supported by the Router gt Status The status of this entry Enabled means the Port Triggering entry is enabled gt Modify To modify or delete an existing entry gt Common Applications Some popular applications already listed in the drop down list of Incoming Protocol To modify or delete an existing entry 1 Find the desired entry in the table 2 Click Modify or Delete as desired on the Modify column Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled Click the Delete All button to delete all entries Once the Router is configured the operation is as follows 1 A local host makes an outgoing connection to an external host using a destination port number defined in the Trigger Port field 2 The Router records this connection opens the incoming port or ports associated with this entry in the Port Triggering table and associates them with the local host 3 When necessary the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field Note 1 When the trigger connection is released the corresponding opened ports will be closed 2 Each rule can only be used by one host on the LAN at a time The trigger connection of other hosts on the LAN
100. left of your browser and click Remote Management submenu On the Remote Management page type a port number except 80 such as 88 into the Web Management Port field Click Save and reboot the Router Remote Management Web Management Port Remote Management IP Address 0 0 0 0 Enter 255 255 255 255 for all Save Figure A 8 Remote Management E Note If the above configuration takes effect you can visit and configure the Router by typing http 192 168 0 1 88 the Routers LAN IP address Web Management Port in the address field of the Web browser If the LAN IP of the modem connected with your router is 118 TL WDR3600 EIA BTU SF Tave MCT er lolimacelenccys 192 168 0 x the default LAN IP of the Router will automatically switch from 192 168 0 1 to 192 168 1 1 to avoid IP conflict in this case please try http 192 168 1 1 88 3 Log in to the Router click the Forwarding menu on the left of your browser and click the Virtual Servers submenu On the Virtual Servers page click Add New then on the Add or Modify a Virtual Server page enter 80 into the blank next to the Service Port and your IP address next to the IP Address assuming 192 168 0 188 for an example remember to Enable and Save Virtual Servers ID Service Port internal Port IP Address Protocol Status Modify 1 1720 1720 192 168 0 169 ALL Enabled hlodity Delete Add Mew Enable All Disable All Delete A
101. ll Figure A 9 Virtual Servers Add or Modify a Virtual Server Entry Service Port PORRO OF KAY Internal Port la Ax Only valid for single Service Port or leave it blank IP Address 192 160 0 100 Protocol LL Status Enabled Common Service Port Select One Figure A 10 Add or Modify a Virtual server Entry The wireless stations cannot connect to the Router 1 Make sure the Wireless Router Radio is enabled 2 Make sure that the wireless stations SSID accord with the Router s SSID 3 Make sure the wireless stations have right KEY for encryption when the Router is encrypted 4 Ifthe wireless connection is ready but you can t access the Router check the IP Address of your wireless stations 119 TL WDR3600 MCU ete BIE A ETT Meier lolimacelenccys Appendix B Configuring the PCs In this section we ll introduce how to install and configure the TCP IP correctly in Windows XP First make sure your Ethernet Adapter is working refer to the adapter s manual if needed 1 Install TCP IP component 1 On the Windows taskbar click the Start button point to Settings and then click Control Panel 2 Click the Network and Internet Connections icon and then click on the Network Connections tab in the appearing window 3 Right click the icon that showed below select Properties on the prompt page LAN or High Speed Internet ocal Area Connection Connected Firewalled Cada Disable Status
102. llowing modes to enable security WPA WPA2 Personal It s the WPA WPA2 authentication type based on pre shared passphrase The Router is configured by this security type by default Version you can choose the version of the WPA PSK security on the drop down list The default setting is Automatic which can select WPA PSK Pre shared key of WPA or WPA2 PSK Pre shared key of WPA automatically based on the wireless station s capability and request Encryption When WPA PSK or WPA is set as the Authentication Type you can select either Automatic or TKIP or AES as Encryption cs Note If you check the WPA WPA2 Personal radio button and choose TKIP encryption you will find a notice in red as shown in Figure 4 36 51 TL WDR3600 MYC BTU a Mei er lolimacelenccys WPAWPA2 Personal Recommended Version Automatic Recommended Y Encryption TKIP v PSK Password 12345670 fou can enter ASCII characters between 8 and 63 or Hexadecimal characters between 8 and 64 Group Key Update Period o an Seconds Keep it default if you are not sure minimum is 30 0 means no update We do not recommend using the TKIP encryption ifthe device operates in 802 11n mode due to the fact that TKIP is not supported by 802 11n specification Figure 4 36 WPA WPA2 Personal PSK Password You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters The default password is t
103. llowing screen as shown in Figure 3 13 and then click Next 16 TL WDR3600 MCU Tee BIER ETT Meier lolimacelenccys Quick Setup Wireless 5GHz Wireless Radio Wireless Network Name Region Band Mode Channel Width Channel Wireless Security O PSK Password O Enable TP LINK_5GHz_13098F Also called the SSID United States wi 5GHz Man mixed _ Auto v Auto _ Disable Security Enable Security WPA PSKWPA2 PSK 12345670 You can enter ASCII characters between 8 and 63 or Hexadecimal characters between 8 and 64 No Change Figure 3 13 Quick Setup Wireless gt Wireless Radio Choose from the drop down list to enable or disable the wireless radio gt Wireless Network Name Also called the SSID Service Set Identification Enter a value of up to 32 characters The same name must be assigned to all wireless devices in your network The default SSID is set to be TP LINK_5GHz_XXXXXX This value is case sensitive For example TEST is NOT the same as fest gt Region Select your region from the drop down list This field specifies the region where the wireless function of the Router can be used It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field If your country or region is not listed please contact your local government agency for assistance Cf Note Lim
104. lug the USB drive click Eject Disk button first Simply pulling USB drive out of the USB port can cause damage to the device and loss of data 4 Mounted volumes of each USB port are subject to the 8 volume limit So you cannot access more than 8 volumes on the USB storage device 5 If you change the storage settings during the storage connection is established then the changes will not take effect until the Router or the client is rebooted 4 9 2 FTP Server Choose menu USB Settings FTP Server you can create an FTP server that can be accessed from the Internet or your local network 62 TL WDR3600 AAEE a Meier lolimacelenccys FTP Server Configuration Server Status Started Internet Access Enable O Disable Service Port The defaultis 21 do not change unless necessary internet Address 0 0 0 0 Public Address 0 0 0 0 Add New Folder Partition Folder Modify volume volume Learming Edit Delete nave Figure 4 51 FTP Server Configuration Service Status Indicates the FTP Server s current status Internet Access Select enable to allow access of the FTP server from the Internet Otherwise select disable to only allow local network access Service Port Enter the FTP Port number to use The default is 21 Name This folder s display name Partition The volume that the folder resides Volume 1 8 is mapping to USB port1 and Volume 9 16 is mapping to USB port2 Folder The real f
105. mplete the settings Then you will go back to the Access Control Rule Management page and see the following list ID Rule Name 5chedule Enable Mocdlify 1 Rule_1 Schedule 1 Edit Delete 4 14 2 Host Choose menu Access Control Host and then you can view and set a Host list in the screen as shown in Figure 4 83 The host list is necessary for the Access Control Rule Host Settings ID Host Description Information Modify 1 Host 1 IF 192 168 0 1 192 168 0 23 Edit Delete Add Mew Delete All Current Mo Fage Figure 4 83 Host Settings gt Host Description Here displays the description of the host and this description is unique gt Information Here displays the information about the host It can be IP or MAC gt Modify To modify or delete an existing entry To add a new entry please follow the steps below 1 Click the Add New button 2 Inthe Mode field select IP Address or MAC Address 1 If you select IP Address the screen shown is Figure 4 84 e In Host Description field create a unique description for the host e g Host_1 eo In LAN IP Address field enter the IP address 2 Ifyou select MAC Address the screen shown is Figure 4 85 e In Host Description field create a unique description for the host e g Host_1 e In MAC Address field enter the MAC address 3 Click the Save button to complete the settings Click the Delete All button to delete all the entries in the table 89
106. n also use the search function to select the SSID to join gt BSSID to be bridged The BSSID of the AP your Router is going to connect to as a client You can also use the search function to select the BSSID to join gt Survey Click this button you can search the AP which runs in the current channel gt Key type This option should be chosen according to the AP s security configuration It is recommended that the security type is the same as your AP s security type gt WEP Index This option should be chosen if the key type is WEP ASCII or WEP HEX It indicates the index of the WEP key gt Auth Type This option should be chosen if the key type is WEP ASCII or WEP HEX It indicates the authorization type of the Root AP gt Password If the AP your Router is going to connect needs password you need to fill the password in this blank 4 6 2 WPS Choose menu Wireless 2 4GHz WPS you can the screen as shown in Figure 4 16 This section will guide you to add a new wireless device to an existing network quickly by WPS Wi Fi Protected Setup function 35 TL WDR3600 BCT eee ENa ella o vi WPS Wi Fi Protected Setup WPS Status Enabled Disable WPS Current PIN 12345670 Restore PIN Gen New PIN Disable Routers PIN Add anew device Add device Figure 4 16 WPS gt WPS Status Enable or disable the WPS function here gt Current PIN The current value of the Router s PIN is
107. n to save this entry To modify or delete an existing entry 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete 42 TL WDR3600 BCT ee BTU ETT MCT erlolimacelenccys 2 Modify the information 3 Click the Save button Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled Click the Delete All button to delete all entries Click the Next button to go to the next page Click the Previous button to return to the previous page For example If you desire that the wireless station A with MAC address 00 OA EB BO 00 0B and the wireless station B with MAC address 00 OA EB 00 07 5F are able to access the Router but all the other wireless stations cannot access the Router you can configure the Wireless MAC Address Filtering list by following these steps 1 Click the Enable button to enable this function 2 Select the radio button Allow the entries specified by any enabled entries in the list to access for Filtering Rules 3 Delete all or disable all entries if there are any entries already 4 Click the Add New button 1 Enter the MAC address 00 0A EB B0 00 0B 00 0A EB 00 07 5F in the MAC Address field 2 Enter wireless station A B in the Description field 3 Select Enabled in the Status drop down list 4 Click the Save button 5 Click the Back button The filtering rules that configured should be
108. net over an always on connection by simulating a dial up connection ADA TL WDR3600 Bye ele Ele Rele ti SSID A Service Set Identification is a thirty two character maximum alphanumeric key identifying a wireless local area network For the wireless devices in a network to communicate with each other all devices must be configured with the same SSID This is typically the configuration parameter for a wireless PC card It corresponds to the ESSID in the wireless Access Point and to the wireless network name WEP Wired Equivalent Privacy A data privacy mechanism based on a 64 bit or 128 bit or 152 bit shared key algorithm as described in the IEEE 802 11 standard Wi Fi A trade name for the 802 11b wireless networking standard given by the Wireless Ethernet Compatibility Alliance WECA see http www wi fi net an industry standards group promoting interoperability among 802 11b devices WLAN Wireless Local Area Network A group of computers and associated devices communicate with each other wirelessly which network serving users are limited in a local area 125
109. nk will work gt ISP Specified IP Address If your ISP does not automatically assign IP addresses to the Router during login please click Use IP address specified by ISP check box and enter the IP address provided by your ISP in dotted decimal notation gt Detect Online Interval The Router will detect Access Concentrator online at every interval The default value is 0 You can input the value between 0 and 120 The value 0 means no detect gt Primary DNS Secondary DNS If your ISP does not automatically assign DNS addresses to the Router during login please click Use the following DNS servers check box and enter the IP address in dotted decimal notation of your ISP s primary DNS server If a secondary DNS server address is available enter it as well Click the Save button to save your settings 4 lf your ISP provides BigPond Cable or Heart Beat Signal connection please select BigPond Cable And you should enter the following parameters Figure 4 7 25 TL WDR3600 EI AAEE a ella o vi WAN Connection Type BigPond Cable User Name Username Password Auth Server Auth Domain MTU Size in bytes The defaultis 1500 do not change unless necessary Connect on Demand Max Idle Time minutes 0 means remain active at all times Connect Automatically Connect Manually Max Idle Time 15 minutes 0 means remain active at all times Connect Disconnected
110. nnection between wireless adapter and Router using either Push Button Configuration PBC method or PIN method fe Note To build a successful connection by WPS you should also do the corresponding configuration of the new device for WPS function meanwhile I Use the Wi Fi Protected Setup Button Use this method if your client device has a Wi Fi Protected Setup button Step 1 Press the WPS Reset button on the back panel of the Router as shown in Figure 4 32 You can also keep the default WPS status as Enabled and click the Add device button in Figure 4 31 Then choose Press the button of the new device in two minutes and click Connect shown in Figure 4 33 Figure 4 32 Add A New Device Enter the new device s PIN Press the button of the new device in two minutes Figure 4 33 Add A New Device Step 2 Press and hold the WPS button of the client device directly Step 3 The Wi Fi Protected Setup LED flashes for two minutes during the Wi Fi Protected Setup process Step 4 When the WPS LED is on the client device has successfully connected to the Router Step 5 Refer back to your client device or its documentation for further instructions Il Enter the client device s PIN on the Router Use this method if your client device does not have the WPS button but has a Wi Fi Protected Setup PIN number Step 1 Keep the default WPS status as Enabled and click the A
111. nternal Port IP Address Status 1 BitCormet 192 166 1 100 25959 25959 TCF 23959 192 166 1 100 Enabled 2 BitComet 192 166 1 100 25959 25959 UDF 23959 1952 168 1 100 Enabled Figure 4 67 UPnP Setting gt Current UPnP Status UPnP can be enabled or disabled by clicking the Enable or Disable button This feature is enabled by default gt Current UPnP Settings List This table displays the current UPnP information 74 TL WDR3600 EAA BIUE ETT Meier lolimacelenccys e App Description The description about the application which initiates the UPnP request e External Port The port which the Router opened for the application e Protocol The type of protocol which is opened e Internal Port The port which the Router opened for local host e IP Address The IP address of the local host which initiates the UPnP request e Status Either Enabled or Disabled Enabled means that the port is still active otherwise the port is inactive Click the Enable button to enable UPnP Click the Disable button to disable UPnP Click the Refresh button to update the Current UPnP Settings List 4 12 Security Security Adwanced Security Local Management Remote Management Figure 4 68 The Security menu There are four submenus under the Security menu as shown in Figure 4 68 Basic Security Advanced Security Local Management and Remote Management Click any of them and you will be able to configure the corresp
112. ntrol Settings and then you can configure the Egress Bandwidth and Ingress Bandwidth in the next screen Their values you configure should be less than 100000Kbps For optimal control of the bandwidth please select the right Line Type and ask your ISP for the total bandwidth of the egress and ingress Bandwidth Control Settings Enable Bandwidth Control Line Type ADSL Other Ingress Bandwidth 2048 Kbps Save Figure 4 96 Bandwidth Control Settings gt Enable Bandwidth Control Check this box so that the Bandwidth Control settings can take effect gt Line Type Select the right type for you network connection If you don t know how to choose please ask your ISP for the information gt Egress Bandwidth The upload speed through the Internet port gt Ingress Bandwidth The download speed through the Internet port 4 16 2 Rules List Choose menu Bandwidth Control Rules List and then you can view and configure the Bandwidth Control rules in the screen below Bandwidth Control Rules List Egress Bandwidth Kbps Ingress Bandwidth Kbps ID Description Enable Modify Min Max Min Max 1 192 168 0 2 192 168 0 23 21 TCP 0 1000 4000 Modify Delete Add New Delete All Nowisthe 1 page Figure 4 97 Bandwidth Control Rules List gt Description This is the information about the rules such as address range S07 TL WDR3600 MYT BTU SF Tave MCT er lolimacelenccys gt
113. o the Internet port of the Router shown in Figure 2 1 5 Connect the PC s and each Switch Hub in your LAN to the Ethernet ports on the Router shown in Figure 2 1 If you have the wireless NIC and want to use the wireless function you can skip this step TL WDR3600 MCU ee BIE a RIELLET 6 Connect the power adapter to the power socket on the Router and the other end into an electrical outlet shown in Figure 2 1 The Router will start to work automatically 7 Power on your Cable DSL Modem Wall Socket Computer USB flash disk gt USB hard drive Some USB hard drives that work at a high power without using any external power adapter might not be supported 1 O O USB1 USB LED USB2 Printer A A E A A A eee A ee Figure 2 2 USB Installation cs Note If you want to use the Router to share files or printer plug the USB storage device to the USB port or connect the printer to the Router with a matching cable TL WDR3600 EA AAEE a Meier lolimacelenccys Chapter 3 Quick Installation Guide This chapter will show you how to configure the basic functions of your N600 Wireless Dual Band Gigabit Router using Quick Setup Wizard within minutes 3 1 TCP IP Configuration The default IP address of the Router is 192 168 0 1 and the default Subne
114. oaded to the IP amp MAC Binding list if the IP address of the item has been loaded before Error warning will prompt as well Likewise Load All only loads the items without interference to the IP amp MAC Binding list 4 18 Dynamic DNS Choose menu Dynamic DNS and you can configure the Dynamic DNS function The Router offers the DDNS Dynamic Domain Name System feature which allows the hosting of a website FTP server or e mail server with a fixed domain name named by yourself and a dynamic IP address and then your friends can connect to your server by entering your domain name no matter what your IP address is Before using this feature you need to sign up for DDNS service providers such aS www comexe cn www dyndns org or www no ip com The Dynamic DNS client service provider will give you a password or key 4 18 1 Comexe cn DDNS If the dynamic DNS Service Provider you select is www comexe cn the page will appear as shown in Figure 4 104 Domain Name Domain Name Domain Name Domain Name Domain Name User Name Password C Enable DONS Connection Status CONS not launching Save Figure 4 104 Comexe cn DDNS Settings To set up for DDNS follow these instructions 1 Enter the Domain Name your dynamic DNS service provider gave 101 TL WDR3600 BCT ee BTU ETT MCT erlolimacelenccys 2 Enter the User Name for your DDNS account 3 Enter the Password for your DDNS account 4
115. of the PC running the service application gt Protocol The protocol used for this application either TCP UDP or All all protocols supported by the Router gt Status The status of this entry Enabled means the virtual server entry is enabled gt Common Service Port Some common services already exist in the drop down list gt Modify To modify or delete an existing entry To setup a virtual server entry 1 Click the Add New button pop up Figure 4 63 2 Select the service you want to use from the Common Service Port list If the Common Service Port menu does not list the service that you want to use enter the number of the service port or service port range in the Service Port field 3 Enter the IP address of the computer running the service application in the IP Address field 4 Select the protocol used for this application in the Protocol drop down list either TCP UDP or All 5 Select the Enabled option in the Status drop down list 6 Click the Save button 70 TL WDR3600 BCT ee BTU SF Tave elit Add or Modify a Virtual Server Entry Service Port EA DOCIOC OT XOX Internal Port E XX Only valid for single Service Port or leave a blank IP Address Status Enabled Ww Common Service Port Select One Ww Figure 4 63 Add or Modify a Virtual Server Entry E Note It is possible that you have a computer or server that has more than one type of available service If so sel
116. on 1 4 2 The Rear Panel Figure 1 2 Rear Panel sketch The following parts are located on the rear panel View from left to right gt Power The Power socket is where you will connect the power adapter Please use the power adapter provided with this TL WDR3600 N600 Wireless Dual Band Gigabit Router On Off The switch for the power Wireless On Off The switch for the wireless function USB The USB port connects to a USB storage device or a USB printer Internet This port is where you will connect the DSL cable Modem or Ethernet Vv Vv Y V WV Ethernet 1 2 3 4 These ports 1 2 3 4 connect the Router to the local PC s TL WDR3600 BYU BIUE A Tave Meier lolimacelenccys WPS Reset Pressing this button for less than 5 seconds enables the WPS function If your client devices such as wireless adapters that support Wi Fi Protected Setup then you can press this button to quickly establish a connection between the Router and client devices and automatically configure wireless security for your wireless network Pressing this button for more than 5 seconds enables the Reset function With the Router powered on press and hold the WPS Reset button approximately 8 seconds until the SYS LED becomes quick flash from slow flash And then release the button and wait the Router to reboot to its factory default settings Wireless antenna To receive and transmit the wireless data TL WDR3600 MCU ee BIUE a Mei
117. on It will take effect after rebooting MAC Clone WAN MAC Address 00 08 01 00 00 05 Your PC s MAC Address 00 19 66 80 54 28 Clone MAC Address Figure A 3 MAC Clone 3 Iwantto use Netmeeting what do I need to do 1 2 If you start Netmeeting as a host you don t need to do anything with the Router If you start as a response you need to configure Virtual Server or DMZ Host and make sure the H323 ALG is enabled How to configure Virtual Server Log in to the Router click the Forwarding menu on the left of your browser and click Virtual Servers submenu On the Virtual Servers page click Add New Then on the Add or Modify a Virtual Server Entry page enter 1720 for the Service Port blank and your IP address for the IP Address blank taking 192 168 0 169 for an example remember to Enable and Save Virtual Servers ID Service Port Internal Port IP Address Protocol Status Modify 1 1720 1720 192 168 0 169 ALL Enabled hlodity Delete Add Mew Enable All Disable All Delete All Figure A 4 Virtual Servers 116 TL WDR3600 BCT ee BTU SF Tave REELL o vi Service Port 1720 LOA OF HG Internal Port 26 Only valid for single Service Port or leave it blank IP Address 192 160 0 163 Protocol HE Status Enabled Common Service Port Select Cne Figure A 5 Add or Modify a Virtual server Entry E Note Your opposite side should call your WAN IP whic
118. ondary DNS If your ISP provides another DNS server enter it into this field After finishing WAN Connection Type selection the Dual Band Selection page will appear as shown in Figure 3 11 Here we choose Concurrently with 2 4GHz and 5GHz 802 11a b g n for introduction Click Next to continue Quick Setup Dual Band Selection This router supports dual band please choose the frequency that you would like to work with Concurrently with 2 4GHz and SGHz 802 11 a b q n Only work in 2 4GHz 802 11 bigin Only work in SGHz 802 11 afn To turn off the wireless radio you can switch the Wireless On Off button located on the back panel of the device to the OFF position Figure 3 11 Quick Setup Dual Band Selection gt 2 4GHz You can use the 2 4GHz band to connect to many classic wireless devices like gaming consoles laptops DVRs ect 14 TL WDR3600 EA AAEE ETT Meier lolimacelenccys gt 5 GHz This band is less crowded and is used for time sensitive music video streaming or gaming Using this band can avoid interference with 2 4GHz networks or noisy devices like cordless phones and microwave ovens Configure the basic parameters for 2 4GHz wireless network in the following screen as shown in Figure 3 12 and then click Next Quick Setup Wireless 2 4GHz Wireless Radio Wireless Network Name Region Band Mode Channel Width Channel Wireless Security O
119. onding function 4 12 1 Basic Security Choose menu Security Basic Security and then you can configure the basic security in the screen as shown in Figure 4 69 75 TL WDR3600 BCT ee BTU SF Tave elit Basic Security Firewall SPI Firewall Enable O Disable PPTP Passthrough Enable Disable L2TP Passthrough Enable Disable IPSec Passthrough Enable Disable FTP ALG Enable O Disable TFTP ALG Enable Disable H323 ALG Enable Disable RTSP ALG Enable O Disable nave Figure 4 69 Basic Security Firewall A firewall protects your network from the outside world Here you can enable or disable the Router s firewall SPI Firewall SPI Stateful Packet Inspection also known as dynamic packet filtering helps to prevent cyber attacks by tracking more state per session It validates that the traffic passing through the session conforms to the protocol SPI Firewall is enabled by factory default If you want all the computers on the LAN exposed to the outside world you can disable it VPN VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pass through the Router PPTP Passthrough Point to Point Tunneling Protocol PPTP allows the Point to Point Protocol PPP to be tunneled through an IP network To allow PPTP tunnels to pass through the Router click Enable L2TP Passthrough Layer Two Tunneling Protocol
120. onjunction with any other antenna or transmitter CE Mark Warning 15880 This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures National Restrictions This device is intended for home and office use in all EU countries and other countries following the EU directive 1999 5 EC without any limitation except for the countries mentioned below Country Restriction Reason remark l General authorization required for outdoor use and Bulgaria None l l public service Outdoor use limited to Military Radiolocation use Refarming of the 2 4 GHz 10 mW e i r p within band has been ongoing in recent years to allow current France the band 2454 2483 5 relaxed regulation Full implementation planned 2012 MHz If used outside of own premises general authorization is Italy None l required General authorization required for network and service Luxembourg None supply not for spectrum This subsection does not apply for the geographical area Norway Implemented oy within a radius of 20 km from the centre of Ny Alesund Russian Federation None Only for indoor applications Note Please don t use the product outdoors in France This device has been designed to operate with the antennas listed below and having a maximum gain of 3dBi Antennas not included in this list or having a gain greater than 3dBi are strictly prohibited for use wit
121. oose how the displayed statistics are sorted Select the Auto refresh checkbox to refresh automatically Click the Refresh button to refresh immediately Click Reset All to reset the values of all the entries to zero Click Delete All to delete all entries in the table 113 TL WDR3600 ENI AAEE a Meier lolimacelenccys Statistics Table IP MAC Address The IP and MAC address are displayed with related statistics The total number of packets received and transmitted by the Router Total The total number of bytes received and transmitted by the Bytes Router The total number of packets received and transmitted in the last ratte Packets Statistic interval seconds The total number of bytes received and transmitted in the last Bytes ae Packets Statistic interval seconds The number of the ICMP packets transmitted to WAN per second saa at the specified Packets Statistics interval It is shown like Current ms current transmitting rate Max transmitting rate The number of UDP packets transmitted to the WAN per second UDP Tx at the specified Packets Statistics interval It is shown like current transmitting rate Max transmitting rate The number of TCP SYN packets transmitted to the WAN per second at the specified Packets Statistics interval It is shown like TCP SYN Tx aa current transmitting rate Max transmitting rate Reset Reset the value of he entry to zero Modify Delete the existing en
122. ption Automatic v Radius Server IP Radius Port 1812 1 65535 0 stands for default port 1812 Radius Password Group Key Update Period in second minimum is 30 O means no update WEP Type Automatic v WEP Key Format Hexadecimal v Key Selected WEP Key Password Key Type Key 1 Disabled wj Key 2 Disabled v Key 3 Disabled Key 4 Disabled Save Figure 4 20 Wireless Security Disable Security If you do not want to use wireless security check this radio button But it s strongly recommended to choose one of the following modes to enable security WPA WPA2 Personal It s the WPA WPA2 authentication type based on pre shared passphrase The Router is configured by this security type by default e Version you can choose the version of the WPA PSK security on the drop down list The default setting is Automatic which can select WPA PSK Pre shared key of WPA or WPA2 PSK Pre shared key of WPA automatically based on the wireless station s capability and request e Encryption When WPA PSK or WPA is set as the Authentication Type you can select either Automatic or TKIP or AES as Encryption cS Note If you check the WPA WPA2 Personal radio button and choose TKIP encryption you will find a notice in red as shown in Figure 4 21 39 gt TL WDR3600 EI AAEE a Meier lolimacelenccys
123. r the configurations are completed 4 19 2 Diagnostic Choose menu System Tools Diagnostic and then you can transact Ping or Traceroute function to check connectivity of your network in the following screen Diagnostic Tools Diagnostic Parameters Diagnostic Tool Ping Traceroute IP Address Domain Name PY Ping Count a 1 50 Ping Packet Size 4 1472 Bytes Ping Timeout 100 2000 milliseconds Traceroute Max TTL 20 1 30 Diagnostic Results The Router is ready Figure 4 110 Diagnostic Tools gt Diagnostic Tool Check the radio button to select one diagnostic too gt Ping This diagnostic tool troubleshoots connectivity reachability and name resolution to a given host or gateway 106 TL WDR3600 Bye leet TR Sy Tale Rel evi gt Traceroute This diagnostic tool tests the performance of a connection E Note You can use ping traceroute to test both numeric IP address or domain name If pinging tracerouting the IP address is successful but pinging tracerouting the domain name is not you might have a name resolution problem In this case ensure that the domain name you are specifying can be resolved by using Domain Name System DNS queries gt IP Address Domain Name Enter the IP Address or Domain Name of the PC whose connection you wish to diagnose Pings Count Specifies the number of Echo Request messages sent The default is 4 Ping Packet Size Spe
124. re folders number is 10 If you want to share a new folder when the number has reached 10 you can delete an existing share folder and then add a new one 2 Ifyou want to change the FTP settings you need to restart FTP Server to make the changes take effect 4 9 3 Media Server Choose menu USB Settings Media Server you can create media server that allows you to share stored content with other computers and devices on your home network and on the Internet Media Server Setting Server Name TP LINK_13098F Server Status Stopped Auto scan every File System Folder Figure 4 53 Media Server Setting gt Server Name The name of this Media Server 64 TL WDR3600 EA AAEE a eile rlolimacelenccys gt Server Status Indicates the Media Server s current status started or stopped You can click the Start button to start the Media Server and click the Stop button to stop it gt Name The display name of this folder gt File System The file system type on the partition can be FAT32 or NTFS gt Folder The real full path of the specified folder gt Delete You can delete the share folder by click Delete To set up your media server please follow the instructions below 1 Plug an external USB hard disk drive or USB flash drive into this Router and then the screen will appear as shown in Figure 4 54 Media Server Setting Server Name TP LINK_13098F Server Status Stopped Auto scan every Fil
125. re provided here Hexadecimal format stands for any combination of hexadecimal digits 0 9 a f A F in the specified length ASCII format stands for any combination of keyboard characters in the specified length e WEP Key Select which of the four keys will be used and enter the matching WEP key that you create Make sure these values are identical on all wireless stations in your network e Key Type You can select the WEP key length 64 bit or 128 bit or 152 bit for encryption Disabled means this WEP key entry is invalid 64 bit You can enter 10 hexadecimal digits any combination of 0 9 a f A F zero key is not promoted or 5 ASCII characters 128 bit You can enter 26 hexadecimal digits any combination of 0 9 a f A F zero key is not promoted or 13 ASCII characters 152 bit You can enter 32 hexadecimal digits any combination of 0 9 a f A F zero key is not promoted or 16 ASCII characters cf Note If you do not set the key the wireless security function is still disabled even if you have selected Shared Key as Authentication Type Be sure to click the Save button to save your settings on this page 4 6 4 Wireless MAC Filtering Choose menu Wireless 2 4GHz Wireless MAC Filtering you can control the wireless access by configuring the Wireless MAC Filtering function shown in Figure 4 24 41 TL WDR3600 MYC BITE SE Tave Meier lolimacelenccys Wireless MAC Filtering Wireless
126. rovide a wireless data rate of up to 300Mbps 2 4GHz 300Mbps 5GHZ gt One 10 100 1000M Auto Negotiation RJ45 Internet port four 10 100 1000M Auto Negotiation RJ45 Ethernet ports supporting Auto MDI MDIX gt Provides USB ports supporting storage FTP Media Print Server gt Provides WPA WPA2 WPA PSK WPA2 PSK authentication TKIP AES encryption security v Shares data and Internet access for users supporting Dynamic IP Static IP PPPoE Internet access Works in 2 4GHz or 5GHz radio bands doubling your network capability Supports Virtual Server Special Application and DMZ host Supports UPnP Dynamic DNS Static Routing Provides Automatic connection and Scheduled Connection on certain time to the Internet Built in NAT and DHCP server supporting static IP address distributing Supports Parental Control and Access Control Connects Internet on demand and disconnects from the Internet when idle for PPPoE Vv Vv Y VW Y VY V YV Provides 64 128 152 bit WEP encryption security and wireless LAN ACL Access Control List V Supports Flow Statistics gt Supports firmware upgrade and Web management TL WDR3600 BCT eee ENa ella o vi 1 4 Panel Layout 1 4 1 The Front Panel Figure 1 1 LEDs on the front panel The Router s LEDs are located on the front panel View from left to right On The Router is initializing or maybe has a system error Flashing The Router is working properly Off The Rout
127. sages for associated clients it sends the next DTIM with a DTIM Interval value You can specify the value between 1 15 Beacon Intervals The default value is 1 which indicates the DTIM Interval is the same as Beacon Interval Enable WMM WMM function can guarantee the packets with high priority messages being transmitted preferentially It is strongly recommended Enable Short GI This function is recommended for it will increase the data capacity by reducing the guard interval time Enabled AP Isolation This function can isolate wireless stations on your network from each other Wireless devices will be able to communicate with the Router but not with each other To use this function check this box AP Isolation is disabled by default 56 TL WDR3600 EAA BIUE ETT Meier lolimacelenccys Cf Note If you are not familiar with the setting items in this page it s strongly recommended to keep the provided default values otherwise it may result in lower wireless network performance 4 7 6 Wireless Statistics Choose menu Wireless Wireless Statistics you can see the MAC Address Current Status Received Packets and Sent Packets for each connected wireless station Wireless Statistics Current Connected Wireless Stations numbers 1 ID MAC Address Current Status Received Packets sent Packets 1 00 04 FEB 88 34 75 STA A5S50C 416 2 Figure 4 42 Wireless Statistics gt MAC Address The connected wirele
128. save your settings CSF Note Only the PC on your LAN can use the MAC Address Clone function 4 5 Dual Band Selection Choose menu Dual Band Selection and you can choose the working frequency for your Router It is recommended that your computers and devices running video and voice applications use the SGHz band while your guest access and computers that are only browsing the web use the 2 4GHz band Quick Setup Dual Band Selection This router supports dual band please choose the frequency that you would like to work with Concurrently with 2 4GHz and SGHz 802 11 a b q n Only work in 2 4GHz 802 11 bigin Only work in SGHz 802 1 1am To turn off the wireless radio you can switch the Wireless On Off button located on the back panel of the device to the OFF position Figure 4 12 Dual Band Selection gt Concurrently 2 4GHz and 5GHz 802 11a b g n Choose this option and then the Router will work concurrently in 2 4GHz and 5GHz frequency gt Only work in 2 4GHz 802 11b g n Choose this option and then the Router will only work in 2 4GHz frequency You can use the 2 4GHz band to connect to many classic wireless devices like gaming consoles laptops DVRs ect gt Only work in 5GHz 802 11a n Choose this option and then the Router will only work in 5GHz frequency This band is less crowded and is used for time sensitive music video 39 TL WDR3600 BCU BUTE Tate Meier lolimacelen
129. ses the DHCP server Reserved IP addresses should be assigned to the servers that require permanent IP settings Address Reservation MAC Address Reserved IP Address Status Modify 00 04 EB 00 23 11 192 168 0 100 Enabled Modify Delete Add Mew Enable All Disable All Delete All Figure 4 46 Address Reservation gt MAC Address The MAC address of the PC for which you want to reserve an IP address 59 TL WDR3600 EJ AAEE a RIELE vi gt Reserved IP Address The IP address reserved for the PC by the Router gt Status The status of this entry either Enabled or Disabled To Reserve an IP address 1 Click the Add New button Then Figure 4 47 will pop up 2 Enter the MAC address in XX XX XX XX XX XX format and IP address in dotted decimal notation of the computer for which you want to reserve an IP address 3 Click the Save button Add or Modify an Address Reservation Entry Reserved IP Address fT Status Enabled Figure 4 47 Add or Modify an Address Reservation Entry To modify or delete an existing entry 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete 2 Modify the information 3 Click the Save button Click the Enable Disabled All button to make all entries enabled disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and Click the Previous button to return the previous p
130. similar to the following list Filtering Rules Deny the stations specified by any enabled entries in the listto access Allow the stations specified by any enabled entries in the listto access ID MAC Address Status Description Modify 1 00 0A EB B0 00 0B Enabled wireless station A Modify Delete 2 00 04 EB 00 07 5F Enabled wireless station B Modify Delete 4 6 5 Wireless Advanced Choose menu Wireless 2 4GHz Wireless Advanced you can configure the advanced settings of your wireless network 43 TL WDR3600 BTU EN a ella vi Wireless Advanced Transmit Power High v Beacon Interval 100 40 1000 RTS Threshold 2346 1 2348 Fragmentation Threshold 2346 256 2346 DTIM Interval 1 1 15 Enable VM Enable Short Gl C Enable AP Isolation Save Figure 4 26 Wireless Advanced Transmit Power Here you can specify the transmit power of Router You can select High Middle or Low which you would like High is the default setting and is recommended Beacon Interval Enter a value between 20 1000 milliseconds for Beacon Interval here The beacons are the packets sent by the Router to synchronize a wireless network Beacon Interval value determines the time interval of the beacons The default value is 100 RTS Threshold Here you can specify the RTS Request to Send Threshold If the packet is larger than the specified RTS Threshold size the Router will send RTS frames to
131. ss station s MAC address gt Current Status The connected wireless station s running status one of STA AUTH STA ASSOC STA JOINED WPA WPA PSK WPA2 WPA2 PSK AP UP AP DOWN Disconnected gt Received Packets Packets received by the station gt Sent Packets Packets sent by the station You cannot change any of the values on this page To update this page and to show the current connected wireless stations click on the Refresh button If the numbers of connected wireless stations go beyond one page click the Next button to go to the next page and click the Previous button to return the previous page f Note This page will be refreshed automatically every 5 seconds DHCP Clients List Address Reservation Figure 4 43 The DHCP menu There are three submenus under the DHCP menu shown in Figure 4 43 DHCP Settings DHCP Clients List and Address Reservation Click any of them and you will be able to configure the corresponding function 57 TL WDR3600 EAA BIUE ETT Meier lolimacelenccys 4 8 1 DHCP Settings Choose menu DHCP DHCP Settings you can configure the DHCP Server on the page as shown in Figure 4 44 The Router is set up by default as a DHCP Dynamic Host Configuration Protocol server which provides the TCP IP configuration for all the PC s that are connected to the Router on the LAN DHCP Settings DHCP Server O Disable Enable Start IP Address 192 168 0 100 End IP A
132. submenus under the Forwarding menu shown in Figure 4 61 Virtual Servers Port Triggering DMZ and UPnP Click any of them and you will be able to configure the corresponding function 4 11 1 Virtual Servers Choose menu Forwarding Virtual Servers and then you can view and add virtual servers in the next screen shown in Figure 4 62 Virtual servers can be used for setting up public services on your LAN A virtual server is defined as a service port and all requests from Internet to this service port will be redirected to the computer specified by the server IP Any PC that was used for a virtual server must have a static or reserved IP address because its IP address may change when using the DHCP function 69 TL WDR3600 BTU TUE a Meier lolimacelenccys Virtual Servers ID Service Port Internal Port IP Address Protocol Status Wodify 1 21 21 192 168 1 100 ALL Enabled Modify Delete Add New Enable All Disable All Delete All Figure 4 62 Virtual Servers gt Service Port The numbers of External Service Ports You can enter a service port or a range of service ports the format is XXX YYY XXX is the Start port and YYY is the End port gt Internal Port The Internal Service Port number of the PC running the service application You can leave it blank if the Internal Port is the same as the Service Port or enter a specific port number when Service Port is a single one gt IP Address The IP address
133. t Mask is 255 255 255 0 These values can be changed as you desire In this guide we use all the default values for description Connect the local PC to the Ethernet ports of the Router and then you can configure the IP address for your PC by the following method Set up the TCP IP Protocol in Obtain an IP address automatically mode on your PC If you need instructions as to how to do this please refer to Appendix B Configuring the PC Then the built in DHCP server will assign IP address for the PC Now you can run the Ping command in the command prompt to verify the network connection between your PC and the Router The following example is in Windows 2000 OS Open a command prompt and type ping 192 168 0 1 and then press Enter gt Ifthe result displayed is similar to the Figure 3 1 it means the connection between your PC and the Router has been established well et C WINDOWS system3 cmd exe Microsoft Windows AP Version 5 1 2606 CCo Copyright 19785 26681 Microsoft Corp Ci sDocuments and Settings english ping 192 168 0 1 Pinging 192 168 B 1 with 32 bytes of data Reply from 192 168 0 1 bytes 32 AE Reply from 192 168 0 1 bytes 32 time lt ims TTL 64 Reply from 192 168 0 1 bytes 32 time lt ims TTL 64 Reply from 192 168 0 1 bhytes 32 timet lt ims TTL 64 Ping statistics for 192 168 6 1 Packets Sent 4 Received 4 Lost cx loss Approximate round trip times in milli seconds Minimum Ams Maximum fms
134. tablished when you attempt to access the Internet again Click the Connect button to connect immediately Click the Disconnect button to disconnect immediately Caution Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background Click the Save button to save your settings 5 If your ISP provides L2TP connection please select L2TP Russia L2TP option And you should enter the following parameters Figure 4 8 WAN WAH Connection Type L2TPRussia LATP w User Hame username Password Connect Disconnected Dynamic IP Static IP Server IP Address Hame IP Address Subnet Mask Gateway DNS Internet IP Address Internet DHS MTU Size in bytes 1460 The defaultis 1460 do not change unless necessary Max Idle Time minutes 0 means rernain active al all times WAN Connection Mode Connect on Demand Connect Automatically Connect Manually Figure 4 8 WAN L2TP Russia L2TP gt User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive gt Dynamic IP Static IP Choose either as you are given by your ISP Click the Connect button to connect immediately Click the Disconnect button to disconnect immediately TL WDR3600 Bye ele Ele Rele ti gt Connect on Demand You can configure the Router to disconnect from
135. teway IP address in dotted decimal notation provided by your ISP gt MTU Size The normal MTU Maximum Transmission Unit value for most Ethernet networks is 1500 Bytes It is not recommended that you change the default MTU Size unless required by your ISP gt Primary Secondary DNS Optional Enter one or two DNS addresses in dotted decimal notation provided by your ISP Click the Save button to save your settings 3 If your ISP provides a PPPoE connection select PPPoE Russia PPPoE option And you should enter the following parameters Figure 4 5 WAN Connection Type PPPoE Russia PPPoE PPPoE Connection User Name username Secondary Connection Disabled DynamicIP Static IP For Dual Access Russia PPPoE Wan Connection Mode Connect on Demand hax Idle Time minutes 0 means remain active at all times Connect Automatically Time based Connecting Period of Time fram o o HH Mt to 23 59 HH Mt Connect Manually hax Idle Time 15 minutes 0 means remain active at all times Connect Disconnected Figure 4 5 WAN PPPoE gt User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive gt Secondary Connection It s available only for PPPoE Connection If your ISP provides an extra Connection type such as Dynamic Static IP to connect to a local area network then you can check the radio button o
136. the basic network parameters To continue please click the Next button To exit please click the Exit button Figure 3 5 Quick Setup Click Next and then WAN Connection Type page will appear shown in Figure 3 6 The Router provides Auto Detect function and supports three popular ways Dynamic IP Static ly ee TL WDR3600 BCT EN ETT eile rlolimacelenccys IP and PPPoE to connect to the Internet It s recommended that you make use of the Auto Detect function If you are sure of what kind of connection type your ISP provides you can select the very type and click Next to go on configuring Quick Setup WAN Connection Type The Quick Setup is preparing to setup your connection type of WAN port The Router will try to detect the Internet connection type your ISF provides ifyou select the Auto Detect option Otherwise you need to specif the connection type manually Auto Detect Let the Router automatically detect the connection type your ISP provides O Pimamic IP Most Common Setup Lise this option ifyou are immediately online once your computer directly plugs into your Cable DSL modem without any setting changes or signing in O Static IP You will need the specific fixed IP address assigned to your connection by your ISP PPPoE Use this option if you used to run a specified program such as Broadband O Connection on the computer with Username and Password provided by your ISP Figure 3 6 WAN
137. the domain name either the full name or the keywords for example google in the blank Any domain name with keywords in it www google com www google cn will be blocked or allowed You can enter 4 domain names 5 Click the Save button Click the Delete All button to delete all the entries in the table Click the Next button to go to the next page or click the Previous button to return to the previous page For example If you desire to restrict the internet activities of host with MAC address 00 11 22 33 44 AA in the LAN to access www google com only you should first follow the settings below 1 Click Add New button in Figure 4 86 to enter the Add or Modify an Access Target Entry page 2 In Mode field select Domain Name from the drop down list 3 In Target Description field create a unique description for the target e g Target_1 4 In Domain Name field enter www google com 5 Click Save to complete the settings Then you will go back to the Target Settings page and see the following list ID Target Description Information Modify 1 Target_1 wy Google com Edit Delete 4 14 4 Schedule Choose menu Access Control Schedule and then you can view and set a Schedule list in the next screen as shown in Figure 4 89 The Schedule list is necessary for the Access Control Rule 92 TL WDR3600 Bye ele Ele Rel Ae ti schedule Settings D Schedule Description Time Modify 1 schedule_1 00 00 24
138. then click the Move button to change the entries order Next Click the Next button to go to the next page Previous Click the Previous button to return to the previous page There are two methods to add a new rule 84 TL WDR3600 EA AAEE a ella vi Method One 1 Click Setup Wizard button and the next screen will appear as shown in Figure 4 78 Quick Setup Create a Host Entry Mode IP Address we Figure 4 78 Quick Setup Create a Host Entry gt Host Description In this field create a unique description for the host e g Host_1 gt Mode Here are two options IP Address and MAC Address You can select either of them from the drop down list If the IP Address is selected you can see the following item gt LAN IP Address Enter the IP address or address range of the host in dotted decimal format e g 192 168 0 23 If the MAC Address is selected you can see the following item gt MAC Address Enter the MAC address of the host in XX XX XX XX XX XX format e g 00 1 1 22 33 44 AA 2 Click Next when finishing creating the host entry and the next screen will appear as shown in Figure 4 79 Quick Setup Create an Access Target Entry Mode IP Address e Target Description IP Address Target Port Protocol Common Service Port please select Figure 4 79 Quick Setup Create an Access Target Entry gt Target Description In this field create a descrip
139. tion for the target Note that this description should be unique e g Target_1 85 gt TL WDR3600 Baye ele Ele Rel evi Mode Here are two options IP Address and Domain Name You can choose either of them from the drop down list If the IP Address is selected you will see the following items gt IP Address Enter the IP address or address range of the target targets in dotted decimal format e g 192 168 0 23 Target Port Specify the port or port range for the target For some common service ports you can make use of the Common Service Port item below Protocol Here are four options All TCP UDP and ICMP Select one of them from the drop down list for the target Common Service Port Here lists some common service ports Select one from the drop down list and the corresponding port number will be filled in the Target Port field automatically For example if you select FTP 21 will be filled in the Target Port automatically If the Domain Name is selected you will see the following items gt Domain Name Here you can enter 4 domain names either the full name or the keywords for example google Any domain name with keywords in it www google com www google cn will be blocked or allowed Click Next when finishing creating the access target entry and the next screen will appear as shown in Figure 4 80 Quick Setup Create an Advanced Schedule Entry Note The Sc
140. try in the table There would be 5 entries on each page Click Previous to return to the previous page and Next to the next page 114 TL WDR3600 Bye leet TR Sy Tale Rel evi Appendix A FAQ 1 How do configure the Router to access Internet by ADSL users 1 First configure the ADSL Modem configured in RFC1483 bridge model 2 Connect the Ethernet cable from your ADSL Modem to the Internet port on the Router The telephone cord plugs into the Line port of the ADSL Modem 3 Login to the Router click the Network menu on the left of your browser and click WAN submenu On the WAN page select PPPoE Russia PPPoE for WAN Connection Type Type user name in the User Name field and password in the Password field type password in the Confirm Password field again finish by clicking Connect WAN Connection Type PPPoE Russia PPPoE PPPoE Connection User Name username Password PTT iii Confirm Password MT TT Figure A 1 PPPoE Connection Type 4 If your ADSL lease is in pay according time mode select Connect on Demand or Connect Manually for Internet connection mode Type an appropriate number for Max Idle Time to avoid wasting paid time Otherwise you can select Auto connecting for Internet connection mode Wan Connection Mode Connect on Demand hax Idle Time minutes 0 means remain active at all times Connect Automat
141. two DNS addresses select Use These DNS Servers and enter the primary and secondary addresses into the correct fields Otherwise the DNS servers will be assigned dynamically from your ISP cS Note If you find error when you go to a website after entering the DNS addresses it is likely that your DNS servers are set up improperly You should contact your ISP to get DNS server addresses Host Name This option specifies the Host Name of the Router Get IP with Unicast DHCP A few ISPs DHCP servers do not support the broadcast applications If you cannot get the IP Address normally you can choose this option It is rarely required Click the Save button to save your settings 2 If your ISP provides a static or fixed IP Address Subnet Mask Gateway and DNS setting select Static IP The Static IP settings page will appear shown in Figure 4 4 WAN Connection Type Static IF IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 Optional MTU Size in bytes 1500 The defaultis 1500 do not change unless necessary Primary DNS 0000 Optional secondary DNS 0 0 0 0 Optional Figure 4 4 WAN Static IP IP Address Enter the IP address in dotted decimal notation provided by your ISP Subnet Mask Enter the subnet Mask in dotted decimal notation provided by your ISP ee TL WDR3600 EAA BIUE ETT Meier lolimacelenccys usually is 255 255 255 0 gt Default Gateway Optional Enter the ga
142. ull path of the specified folder To set up your FTP Server please follow the instructions below 1 2 6 Plug an external USB hard disk drive or USB flash drive into this Router Click the Enable Disable radio box to enable disable Internet access to FTP from Internet port Specify a port for the FTP server to use The default port number is 21 The Internet Address displays the WAN IP address of this router so that other users can access FTP via this address If WAN type is PPPoE PPTP L2TP two connections will be available Therefore users can access FTP server via two connections Users in a private LAN can access ftp server via Public Address while Internet users can access ftp server via Internet Address Click the Start button to start the ftp server To add a new folder follow the instructions below 1 Click Add New Folder in Figure 4 51 63 TL WDR3600 BYU BTU Tave eli ovio Add or Modify Share Folder Partition Share entire partition Folder Location i Select Folder Learning Photos Printing Figure 4 52 Add or Modify Share Folder 2 Select the Share entire partition or a specific folder option 3 Enter display name of the share folder in Display Name filed 4 Click the Save button to save the settings You can click the upper button to go to the upper folder You can click the Back button to return to the ftp server configuration page Cf Note 1 The max sha
143. will be refused 3 Incoming Ports ranges cannot overlap each other 4 11 3 DMZ Choose menu Forwarding DMZ and then you can view and configure DMZ host in the screen 73 TL WDR3600 Bye cele TEA Sy late Rel Ade ti shown in Figure 4 66 The DMZ host feature allows one local host to be exposed to the Internet for a special purpose service such as Internet gaming or videoconferencing The Router forwards packets of all services to the DMZ host Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may be changed when using the DHCP function eee Current DMZ Status O Enable Disable DMZ Host IP Address 192 168 0 100 Figure 4 66 DMZ To assign a computer or server to be a DMZ server 1 Click the Enable button 2 Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field 3 Click the Save button 4 11 4 UPnP Choose menu Forwarding UPnP and then you can view the information about UPnP in the screen shown in Figure 4 67 The Universal Plug and Play UPnP feature allows the devices such as Internet computers to access the local host resources or devices as needed UPnP devices can be automatically discovered by the UPnP service application on the LAN Current UPnP Status Enabled Current UPnP Settings List ID App Description External Port Protocol I
144. wn in Figure 4 65 2 Select a common application from the Common Applications drop down list then the Trigger Port field and the Incoming Ports field will be automatically filled If the Common Applications do not have the application you need enter the Trigger Port and the Incoming Ports manually 3 Select the protocol used for Trigger Port from the Trigger Protocol drop down list either TCP UDP or All 4 Select the protocol used for Incoming Ports from the Incoming Protocol drop down list either TCP or UDP or All 5 Select Enable in Status field 6 Click the Save button to save the new rule Add or Modify a Port Triggering Entry Trigger Port Trigger Protocol Incoming Ports Incoming Protocol Status Enabled Common Applications Select Cne Figure 4 65 Add or Modify a Triggering Entry gt Trigger Port The port for outgoing traffic An outgoing connection using this port will trigger this rule gt 2 TL WDR3600 EAA BIUE ETT Meier lolimacelenccys gt Trigger Protocol The protocol used for Trigger Ports either TCP UDP or All all protocols supported by the Router gt Incoming Port The port or port range used by the remote system when it responds to the outgoing request A response using one of these ports will be forwarded to the PC which triggered this rule You can input at most 5 groups of ports or port sections Every group of ports must be separated with for examp
145. work LAN MAC Clone Figure 4 2 the Network menu There are three submenus under the Network menu shown in Figure 4 2 WAN LAN and MAC Clone Click any of them and you will be able to configure the corresponding function 44 1 WAN Choose menu Network WAN you can configure the IP parameters of the WAN on the screen below 1 If your ISP provides the DHCP service please choose Dynamic IP type and the Router will automatically get IP parameters from your ISP You can see the page as follows Figure 4 3 WAN Connection Type Dynamic IP IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 SS Renew MTU Size in bytes 1500 The defaultis 1500 do not change unless necessary d Primary DNS Secondary DNS Optional Host Name TLAMWDRS500 C GetlF with Unicast DHCP tis usually not required Figure 4 3 WAN Dynamic IP sA TL WDR3600 Bye ele TEA Sy Tale Rel Ade i This page displays the WAN IP parameters assigned dynamically by your ISP including IP address Subnet Mask Default Gateway etc Click the Renew button to renew the IP parameters from your ISP Click the Release button to release the IP parameters MTU Size The normal MTU Maximum Transmission Unit value for most Ethernet networks is 1500 Bytes It is not recommended that you change the default MTU Size unless required by your ISP Use These DNS Servers If your ISP gives you one or
146. y use 255 255 255 0 as the subnet mask cf Note 1 If you change the IP Address of LAN you must use the new IP Address to log in the Router 2 Ifthe new LAN IP Address you set is not in the same subnet the IP Address pool of the DHCP server will change accordingly at the same time while the Virtual Server and DMZ Host will not take effect until they are re configured 4 4 3 MAC Clone Choose menu Network MAC Clone you can configure the MAC address of the WAN on the screen below Figure 4 11 MAC Clone WAN MAC Address O0 19 66 CB 45 66 Restore Factory MAC Your PC s MAC Address Clone MAC Address save Figure 4 11 MAC Address Clone Some ISPs require that you register the MAC Address of your adapter Changes are rarely needed here 34 TL WDR3600 EA AAEE a MCT er lolimacelenccys gt WAN MAC Address This field displays the current MAC address of the Internet port If your ISP requires you to register the MAC address please enter the correct MAC address into this field in XX XX XX XX XX XX format X is any hexadecimal digit gt Your PC s MAC Address This field displays the MAC address of the PC that is managing the Router If the MAC address is required you can click the Clone MAC Address To button and this MAC address will fill in the WAN MAC Address field Click Restore Factory MAC to restore the MAC address of Internet port to the factory default value Click the Save button to
147. z 3dBi 4 9 5 825GHz Environmental and Physical Operating 0 C 40 C 32 F 104 TF Temperature Storage 40 C 70 C 40T 158 F 7 Operating 10 9 RH Non condensing Humidity Storage 5 90 RH Non condensing Standards Sensitivity PER Only 2 412GHz 2 462GHz is allowed to be used in USA which means only channel 1 11 is available for American users to choose 123 TL WDR3600 BYU BIUE A Tave Meier lolimacelenccys Appendix D Glossary gt 802 11n 802 11n builds upon previous 802 11 standards by adding MIMO multiple input multiple output MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity perhaps through coding schemes like Alamouti coding The Enhanced Wireless Consortium EWC 3 was formed to help accelerate the IEEE 802 11n development process and promote a technology specification for interoperability of next generation wireless local area networking WLAN products gt 802 11b The 802 11b standard specifies a wireless networking at 11 Mbps using direct sequence spread spectrum DSSS technology and operating in the unlicensed radio spectrum at 2 4GHz and WEP encryption for security 802 11b networks are also referred to as Wi Fi networks gt 802 11g specification for wireless networking at 54 Mbps using direct sequence spread spectrum DSS

TP-LINK TL-WDR3600 router

Contents

Download Pdf Manuals

Related Search

Related Contents