Mace MAC-MON-17LED
Contents
1. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generation uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Precautions gt Read all of these instructions and save them for later use gt Follow all warnings and instructions on the product gt Product Donot cover or block the vent holes in the case Do not insert sharp objects or spill liquid into the LED monitor through cabinet slots They may cause accident fire electric shock or failure Disconnect the power plug2. m LED CCTV Security Surveillance Monitors A Genuine Mace Accessory a Mace sec Garey T TN User Guide Introduction and Package Contents Congratulations on your purchase You can expect only the sharpest and most brilliant color images from this security surveillance monitor Featuring simple OSD controls and built in speakers you will find this monitor both easy to use and a pleasure to look at Contents e Monitor 12VDC Power Adapter D Sub 15 pin VGA Connector Cable User Guide Hardware Installation The following sections in this guide give clear step by step descriptions of the installation process and explain how to use the monitor for optimum results Please pay attention to the Regulations and Warnings Section of this User Guide before setting up the security monitor Failure to do so may inadvertently result in personal injuries or machine damage Mace LED CCTV Security Surveillance Monitors Specifications Video inputs Video outputs Audio inputs Speakers Display modes Multi window support OSD control OSD languages Auto adjustment Wall mount Max resolution Response time Color depth Pixel pitch Display area H V Viewing angle Power Temperature 1 HDMI 1 VGA 2 Composite BNC 2 Composite BNC 1 VGA PC Audio 2 RCA Composite Audio 2 x 1 5W rear projection HDMI VGA PC AV1 AV2 PIP POP Off AV or VGA sub sources Picture Mode Contras
3. from the AC outlet if you will not use it for an indefinite period of time Donot attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage potentials or other risks Do not touch the screen directly with your fingers You may damage the screen and oil from your skin is difficult to remove Do not apply pressure to the screen The LED surface is delicate gt Power Use the type of power indicated on the marking label Mace LED CCTV Security Surveillance Monitors 10 gt Plugs Donotremove any of the prongs of the monitor s three pronged power plug Disconnect the power plug from the AC outlet under following conditions e f you will not use it for an indefinite period time When the power cord or plug is damaged or frayed ifthe product does not operate normally when the operation instructions are followed Adjust only those controls that are covered by the operating instructions Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation ifthe product has been dropped or the cabinet has been damaged e ifthe product exhibits a distinct change in performance this indicates a need for service gt Power and extension cords Donotallow anything to rest on the power cord Donot locate this product where people will walk on the c
4. Control Your LED color monitor has a simple button layout for controlling the monitor and OSD On Screen Display functions Button MAC MON 17LED Functions MAC MON 19LED Button Function Enter the main menu Switch between modes PC AVT and AV2 Automatically adjusts H Position V Position Pixel Clock and Phase for an optimal image in PC mode only Toggle the display between Standby mode and On Off Press Power and wait for 6 seconds LED Status Power State LED Color spay pon free reen Mace LED CCTV Security Surveillance Monitors 4 OSD Control OSD Menu Picture Mode Picture Mode Contrast Brigntness Tint saturation Sharpness Color Temp DNR Picture Mode Press lt or gt to select Picture Mode User Standard Movie Vivid Contrast This is used to set the brightness of the screen Press lt or gt to adjust the parameter This is used to adjust the image contrast g Press lt or gt to adjust the parameter This is used to adjust the image Tint Press lt or gt to adjust the parameter Saturation This is used to adjust the image saturation Press lt or to adjust the parameter sharoness Adjust the sharpness It makes the image become soft p Press lt or gt to adjust the parameter Press OR to adjust color tones olen temp Cool Warm Normal Press OR to adjust noise reduction High Low Off Mid
5. Note VGA Mode Contrast Brightness Color Temp Auto Adjust Press lt or gt to adjust volume level Press lt or gt to select sound Off On Mace LED CCTV Security Surveillance Monitors 5 OSD Menu Settings Mode AV HDMI Mode jea Language H Position H Zoom V Position V Zoom Scale Mode Reset VGA Mode i Setting Language English H Position V Position H Zoom V Zoom Phase Scale Mode Reset Press lt or gt to select language Move the display picture left or right Press lt or gt to adjust the parameter Adjust the H size of the display picture Press lt or gt to adjust the parameter Move the display picture up or down Press lt or gt to adjust the parameter Adjust the V size of the display picture Press lt or gt to adjust the parameter Press lt or gt to adjust the parameter Phase Press lt or gt to adjust the parameter Adjust the V size of the display picture Scale Mode Press lt or gt to adjust Full 16 9 Reset Recall Default value Note Clock and Phase setting in VGA Mode only Mace LED CCTV Security Surveillance Monitors OSD Menu PIP POP Setup Mode fa A s5 Multi Window Sas Press lt or gt to select Multi Window PIP POP Off Press lt or gt to select AV VGA Adjust the size of Sub S
6. ignal cable is properly connected to the display card computer Check the DB 15 signal cable connector on both ends for bent or pushed in pins The display card should be properly seated in its card slot within your PC Ensure that the computer s power switch is ON Ensure that the monitor s power switch is ON Unplug the power cord of the monitor from the AC outlet wait a few minutes then to plug the power cord into the AC outlet again This will reset the monitor and power supply Power LED is RED with no image on the screen Check the DB 15 signal cable to ensure that it is properly attached to the graphics display card Check the DB 15 signal cable on both ends for bent or pushed in pins Make sure the computer is not in Power Saving mode move the mouse or press a key on the keyboard No sound coming from the audio speakers Mace LED CCTV Security Surveillance Monitors Ensure that the audio cable is connected to the line out on the audio card and the line in on the monitor Inspect the audio cable for any apparent damage Double check by switching to another audio cable to see if the audio works Regulations amp Maintenance FCC Compliance This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation
7. late has a hard surface coating to prevent scratches However the use of strong chemical cleaning agents may damage this coating Use only a mild soap or detergent and water or specially formulated cleaners made for cleaning glass panels Avoid direct contact with water or other liquids Never use the LED monitor in or around areas where water may pose a potential hazard to normal operation Only use the LED monitor indoors and avoid monitor contact with oil vapor steam moisture and dust The LED monitor should be used in a clean and low humidity environment Keep the LED monitor away from heaters or other heat sources such as lighting equipment or direct sunlight Keep the LED monitor away from sharp objects WARNING Any unauthorized modification to this equipment could result in the revocation of the authorization to operate the equipment and void the product warranty Mace LED CCTV Security Surveillance Monitors Frequently Asked Questions Power button does not respond Check the power cord to ensure that it is securely plugged into the monitor base and also into the electrical outlet Ensure there is electrical power coming from the AC outlet Use another device to check for power Unplug the power cord of the monitor from the AC outlet wait a few minutes then to plug the power cord into the AC outlet again This will reset the monitor and power supply No image on the screen Ensure that the DB 15 s
8. ord Use the proper power cord with correct attachment plug type If the power source is IZOVAC use a power cord that has UL and C UL approvals If the power source is a 240VAC supply use the tandem T blade type attachment plug with ground conductor power cord that meets the respective European country s safety regulations such as VDE for Germany Do not overload wall outlets or power cords Ensure that the total of all units plugged into the wall outlet does not exceed 10 amperes Ensure that the total ampere rating of all units plugged into the extension cord is not over the cord s rating f the power supply cord which came with your monitor is to be connected to the PC instead of the wall outlet this equipment is to be used with UL TUV approved computers with receptacle rated 100 240V AC 50 60Hz 2 0ACminimum gt Environment Place the monitor on a flat and level surface Place the monitor in a well ventilated place Keep the monitor away from Extremely hot cold or humid places places directly under sunlight dusty surroundings equipment that generate strong magnetic fields Mace LED CCTV Security Surveillance Monitors 11 Mace SECURITY PRODUCTS 5101 NW 21st Ave Suite 210 Fort Lauderdale FL 33309 www mace com 877 585 6223
9. ource window Press lt or gt to select Large Small Move the position of Sub Source window Press lt or gt to select position LU RD RU LR Choose the border color of Sub Source window Border Color Press lt or gt to select color Black Blue Press lt or gt to select Main Sub mode Swap Press S Select to Swap the Source of Main and Sub Note 1 AV1and AV2 HDMI and VGA cannot be displayed at the same time on the monitor in PIP POP mode 2 If POP mode Is selected both images are scaled to fit the screen Mace LED CCTV Security Surveillance Monitors 7 Caring for your LED Security Monitor The monitor is a sensitive piece of electronic equipment Proper care can prevent accidental damage to the LED panel or the monitor itself By following these guidelines you can ensure many years of trouble free use 1 The LED monitor s casing and LED glass panel can be cleaned with a soft lint free cloth Never use scrub pads or other cleaning materials with abrasive surfaces to clean your LED monitor a A slightly damp cloth or newspaper may be used to clean the glass plate of fingerprints or smudges b For the plastic case a mild detergent may be used to clean the surface However you should ensure not to use too much detergent or water as this could leak into the interior of the casing DO NOT use cleaning fluids based on alcohol methylated spirit or ammonia The glass p
10. t Brightness Tint Saturation Sharpness Color Temp DNR Position Sound PIP English German French Italian Soanish Russian Turkish Polish Dutch Czech Yes Only for VGA mode Removable stands VESA mount ready case 1280 x 1024 Sms 16 7 million colors 0 264 x 0 264 mm 0 294 x 0 294 mm 13 3 x 10 64 in 14 81 x 11 85 in 557 9 x 270 5 MM 376 5 x 501 06 mm Vertical 80 80 Horizontal 85 85 AC 100 240V 50 60Hz 12VDC Power Adapter 15W max in ON Mode Under 3W in Power Saving Mode 100 VAC Under 5W in Power Saving Mode 240 VAC Operation 32 104 F 0 40 C Storage 14 140 F 10 60 C Humidity 10 90 15 16 x 15 12 x 6 5 in 16 69 x 16 34 x 6 5 in Dimensions W x H x D 385 x 384 x 165 MM 424 x 415 x165 mm 7 5 Ibs 3 4 Kgs 11 7 Ibs 5 3 Kgs Power Supply Adapter VGA Cable User Guide FCC CE ROHS Weight Included accessories Regulatory compliance VGA PC audio AV audio AV1 AV1 AV2 AV2 Input Output Input Output a A D gt m om AV2 AV1 AV1 AV audio PC audio VGA input Output input Mace LED CCTV Security Surveillance Monitors 2 VGA Timing Item Resolution H Freq KHz V Freq HZ a eosooaronzs seo eos z z Note The timings with presets are recommended Adjustments to the timing need to be made manually if they are not included in this list Mace LED CCTV Security Surveillance Monitors 3 Monitor and OSD
Download Pdf Manuals
Related Search