Home

Miele G 2874 SCVi

1. The outer surfaces of the dishwasher are susceptible to scratching Contact with unsuitable cleaning agents can alter or discolour the outer surfaces Cleaning the wash cabinet The wash cabinet is largely self cleaning provided that the correct amount of detergent is always used If however there are limescale or grease deposits in the cabinet these can be removed with a proprietary dishwasher cleaner or conditioner Cleaning the door and the door seal m Wipe the door seals regularly with a damp cloth to remove food deposits m When the dishwasher is being loaded food and drink residues may drip onto the sides of the dishwasher door These surfaces are outside the wash cabinet and are not accessed by water from the spray arms Any soiling should be wiped off these surfaces before the door is closed Cleaning the reflector panel The reflector panel for the In operation indicator light is situated in the coverplate underneath the worktop m he reflector panel should only be wiped with a damp cloth or a suitable cleaning agent designed for use on plastic 43 Cleaning and care Cleaning the control panel and door front N Remove any soiling immediately If not it might become impossible to remove and could cause the outer surface to alter or discolour m The control panel should only be wiped with a damp cloth m Clean stainless steel surfaces using a microfibre cloth or with a solutio
2. but would still like to open the door at the end of the programme then make sure that you open the door fully Otherwise steam from the dishwasher could damage the edge of the worktop because the fan is no longer running Switching off At the end of a programme m Open the door m Switch the dishwasher off using the Off button O The dishwasher will continue to use electricity until it is switched off with the Off button O If the dishwasher is not going to be used for a longer period of time e g whilst on holiday the tap should be turned off Unloading the dishwasher Dishes tend to break and chip more easily when they are hot Allow the dishes to cool until they are comfortable enough to handle before unloading them If you open the door fully after switching off the dishes will cool much faster First unload the lower basket then the upper basket and finally the cutlery tray depending on model This will prevent water drops from the upper basket and cutlery tray from falling onto the dishes in the lower basket Interrupting a programme Operation is interrupted as soon as the door is opened If the door is closed again the programme will continue from the point it was at before the door was opened N Water in the dishwasher may be hot Danger of scalding Only open the door if absolutely necessary and exercise extreme caution when doing so Before closing the door again leave it ajar for
3. Cleaning the filters m Switch the dishwasher off m Turn the handle anti clockwise to release the filter combination CD m Take the filter combination out remove any coarse particles and rinse the filter well under running water Use a nylon brush if necessary 45 Cleaning and care To clean the inside of the filter the flap m Replace the filter combination so that must be opened it lies flat in the base of the wash cabinet m Press catches together in the direction of the arrows as shown and m Then turn the handle clockwise until open the filter both arrows point towards each other This will lock the filter m Rinse all the filters under running combination in place water m Then close the flap so that the catch Take care when you are fitting engages the filter combination that it is secured in position correctly Otherwise coarse soil could get into the circulation system and cause a blockage 46 Cleaning and care Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings The spray arms should therefore be inspected and cleaned regularly approx every 4 6 months m Switch the dishwasher off Remove the spray arms as follows m Take out the cutlery tray if your dishwasher is fitted with one m Push the top spray arm upwards to engage the inner ratchet Then unscrew the spray arm m Push the middle spray arms upwards D to engag
4. Fax 0800 463 453 www miele co nz Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Alteration rights reserved G2874 1409 CE M Nr 07 600 690 00
5. Plastic items are discoloured There are rust stains on cutlery Possible cause This may be caused by the detergent The glassware is not dishwasher proof The surfaces are affected The wash temperature of the selected programme was too low Remed Change your detergent There is no remedy Purchase glassware which is dishwasher proof Select a programme with a higher wash temperature The bleaching effect of the detergent used is too low Natural dyes e g from carrots tomatoes or tomato sauce may be the cause The amount of detergent used or its bleaching effect was not sufficient to deal with natural dyes The affected items are not corrosion resistant Change your detergent Use more detergent See Operation Discolouration is irreversi ble There is no remedy Purchase cutlery which is dishwasher proof A programme was not run after dishwasher salt was added Traces of salt have got into the wash cycle Always run the Quick wash programme without any crockery in the dishwasher and without selecting the Turbo function after adding dishwasher salt 57 Maintenance Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose The filter must be cleaned when dirty otherwise insufficient water flows into the wash cabinet The plastic housing of the water connection contains an electrical co
6. m Select the option you want and confirm this with OF m Confirm the following questions with Dk m l necessary press any button to start the Demo mode you have selected m To cancel it press any button and confirm it with OK To switch Demo mode off m Select Off and confirm with OE m Confirm the question Switch demo mode aff with DE Factory default setting If you have altered any settings from the factory default you can re set them back to the factory default settings m Confirm the question Reset factorw default settings with OK m Confirm the message All settings reset to factory default with OF To close the Settings F menu Press C to come out of the Settings P menu and return to the main menu 85 86 87 Miele Australia Pty Ltd ABN 96 005 635 398 Melbourne 1 Gilbert Park Drive Knoxfield VIC 3180 Telephone 03 9764 7130 Fax 03 9764 7149 Sydney 3 Skyline Place French Forest NSW 2086 Telephone 02 8977 4230 Fax 02 8977 4249 Brisbane 39 Harvey Street North Eagle Farm QLD 4009 Telephone 1800 798 578 Fax 1800 799 578 Adelaide 79 81 Sir Donald Bradman Drive Hilton SA 5033 Telephone 1800 018 770 Fax 1800 799 578 Perth 205 207 Stirling Highway Claremont WA 6010 Telephone 1800 094 872 Fax 1800 799 578 www miele com au Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland New Zealand Telephone 0800 264 353
7. Refer to the manufacturer s packaging as to whether the combi tabs are suitable for the water hardness level in your area Please note that the cleaning and drying results of tab detergents can vary greatly For optimum cleaning and drying results use Miele dishwasher detergent and add Miele salt and Miele rinse aid separately Under certain circumstances unsatisfactory washing and drying results might be noticed when using combination dishwasher detergents These products contain a combination of detergent and rinse aid or detergent and salt 2 in 1 or detergent rinse aid and salt 3 in 1 Drying results might not be as good as expected or residues or flecks might be left on crockery If results are still unsatisfactory even after seeking advice from the detergent manufacturer we suggest that you change to a different product or use a traditional dishwasher detergent 33 Operation Dispensing m Follow the dosage recommended by the manufacturer on the packaging m Unless directed otherwise use one detergent tab or add 20 to 30 ml in compartment II depending on the level of soiling With very heavy soiling you can also add a small amount of detergent to compartment see Programme chart 34 m Do not use tabs with the Quick wash programme as they will not dissolve properly Failure to dispense the recommended amount of detergent may impair cleaning results Avoid inhalation of powder
8. a complete programme is not yet needed Pre wash Adds a pre wash phase to the selected programme Soak Forloosening very stubborn food residues from pots pans and casserole dishes If you are using powder dishwasher detergent add approx 5 g to compartment I Longer drying For improved drying of awkwardly shaped dishes and also plastic items m Select the Extras you want and confirm with OE A tick will appear beside the Extra to show that it has been set m To cancel the selection of an Extra press the appropriate button again m When you have finished selecting Extras confirm with OF The display will change back to the programme menu The message Extras selected will appear in the display 37 Operation Start the programme m Select the Start option The message Please clase the door will appear If you want to select a different programme or make other changes select Back and cancel the programme with the Cancel function m Close the door The In operation indicator lights up The programme starts If you open the door Add ar itern will appear in the display As long as this prompt is showing crockery can be added without compromising the wash results A programme can only be cancelled in the first few minutes Otherwise the programme must continue to the end so that important programme stages e g reactivating the water softener are not omitted 38
9. accessed by m insert cutlery with the handles facing downwards water 32 Operation Detergent Only use detergents formulated for domestic dishwashers Do not use washing up liquid Miele branded dishwasher cleaning products are available from the Miele Spare Parts Department or via the internet at www miele shop com Active ingredients Modern detergents contain various active ingredients the most important of which are Phosphates to prevent calcification Alkalis to aid removal of dried on soiling Enzymes to break down starch and loosen protein Oxygen based bleaching agents to remove coloured stains e g tea coffee tomato sauce Most dishwasher detergents contain phosphate and are mildly alkaline with enzymes and oxygen based bleaching agents Phosphate free products are rare Types of detergent Powder and liquid gel detergents These detergents allow you to adjust the amount dispensed according to the amount of load and level of soiling Tab detergents These are suitable for most levels of soiling A variety of combination products is also available see Settings Detergent type In addition to detergent combi tabs contain rinse aid and salt substitutes Combi tabs are available as 3 in 1 or when they also contain other components such as glass and stainless steel protective additives and enhanced cleaning power as 4 in 1 5 in 1 etc
10. against the cup rack or suspended from it m The cup rack can be raised to make more room for tall items 29 Loading the dishwasher Narrow vario insert You can remove the narrow vario insert to make more room for larger items of crockery e g a large flat pot or another type of insert To remove it m Press the insert downwards and press the catch inwards at the same time To replace it m Position the narrow vario insert in the back right hand side of the lower basket m Fit the insert into the lower basket with the hooks going under the long cross piece as illustrated m Press down on the insert until it clicks into position 30 Bottle holder The bottle holder can be used to wash narrow items e g milk and baby bottles m it can be inserted into the bottom basket in more than one place See the areas marked in white in the illustration However do not place a bottle holder in the corners Water will not be able to access the bottles properly and they will not get clean Loading the dishwasher Q Cutlery Fi Cutlery tray depending on model 7 N Wr N IN j li n MIOS M NN T UND DR IN UNS AR A V 3 LA O IQ Q Mi Qi Q NO a Y La Dore
11. and confirm this with DIE Adjust Sensor wash You can adjust the Sensor wash programme so that it will remove stubborn soiling in a lightly soiled load m Select Ves and confirm with OK Settings menu F Change main menu You can change the order of the programmes in the main menu and also enter your favourite programmes into the first two programme places Sensor wash v Cancel Set position 1 Continue m Use the Y button to find the programme that you would like to have as your first choice in the main menu and then select it using the button next to the programme m Confirm with Continue m Use the Y button to find the programme that you would like to have as your second choice in the main menu and then select it using the button next to the programme m Confirm with Continue The programmes you have chosen will appear in the display If you want to change the position of another programme select the Back function until you reach the relevant menu m When you have finished making changes confirm with Finished 81 Settings menu F Save extras You can set additional functions e g Pre wash for individual programmes see Operation Selecting Extra options You can use the Save extras option to save settings you have chosen for a particular programme so that they are automatically selected when you run the programme in the future The dishwasher is delivered with this function
12. data Dishwasher model Height Height of building in recess Width Width of building in recess Depth Weight Voltage Connected load Fuse rating Test certificates awarded Water pressure flow rate Hot water connection Delivery head Drainage length Mains cable Capacity depending on model G 1XXX 80 5 cm adjustable 6 5 cm Min 80 5 cm 4 6 5 cm 59 8 cm 60 cm 57 cm Max 55 kg 230 V 2300 W 10A Electrical safety Typetest Mark C Tick Mark 30 1000 kPa 0 3 10 bar Up to max 60 C Max 1m Max 4m approx 1 7m 12 14 place settings G 2XXX 84 5 cm adjustable 6 5 cm Min 84 5 cm 4 6 5 cm 59 8 cm 60 cm 87 lai Max 61 kg 230 V 2300 W 10A Electrical safety Typetest Mark C Tick Mark 30 1000 kPa 0 3 10 bar Up to max 60 C Max 1m Max 4m approx 1 7 m 12 14 place settings 75 Settings menu F Settings menu for changing standard settings To open the Settings menu 76 m Switch the dishwasher on with the On button if it is switched off The programme selection menu will appear in the display If the memory function is activated the menu for the programme last selected will be displayed instead see Memory If this is the case press the Clear sensor to switch to the main menu Settings hain menu m Select Settings P The display will change to show the Settings P menu Language F Setti
13. detergents and do not ingest dishwasher detergent Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose mouth and throat if swallowed or inhibit breathing Consult a doctor immedi ately if detergent has been swallowed or inhaled Keep detergent and other household agents out of the reach of children at all times Keep children away from the dishwasher when the door is open There could still be detergent residues in the cabinet To avoid the danger of children coming into contact with the dishwasher detergent only add detergent just before starting the programme and close the door activating the child safety lock if your dishwasher is fitted with one Operation Adding detergent For information Compartment holds max 10 ml Compartment Il holds max 50 ml There are markings in compartment Il to assist with dispensing 20 30 The marks indicate a level of approx 20 or 30 ml when the door is open in a horizontal position m Press the opening catch on the detergent dispenser The flap will spring open The flap is always open at the end of a programme m Add the required amount of detergent and close the flap m Make sure that the detergent packaging is properly closed after use to avoid it getting damp and becoming lumpy 35 Operation Switching on m Open the tap if it is closed m Open the door m Make sure the spray arms are not
14. ease ata 82 TOMPO UE 2 cuina cantos rl po iria Tc ne ae 82 BUZZ 452 8 iran E 83 Keypad TOMES miii ena e aa ed 84 Bri htnessir is x ie eee ei Ree eye ade Paw ed We ba qs es 84 MEMORY rc P PP 84 Showroom programme iesse vec a gay x x ERE RUE Layee adeeb de 85 Factory default setting iiis es 85 To close the Settings P menu iu caa se tu es eux cic oa acci Ate dtc a a 85 Guide to the appliance Appliance overview zl Tee E LU E T o Upper spray arm not visible Filter combination 2 Cutlery tray depending on model Data plate 8 Upper basket 9 In operation indicator light Middle spray arm Rinse aid reservoir Air inlet for drying Dual compartment detergent depending on model dispenser Lower spray arm 42 Salt reservoir Guide to the appliance Control panel c oo i 100 Miele gt gt 9 e D Selector buttons On button with indicator light For selecting the option displayed For switching the dishwasher on next to them DOF button O Nue ine NAUES Gisplayed For switching the dishwasher off For moving to other menus 8 Service interface Used by service technicians to run diagnostic checks on your
15. fitted with a non return valve which prevents dirty water from flowing back into the dishwasher via the drain hose The dishwasher is supplied with approx 1 5 m of flexible drain hose with an internal diameter of 22 mm The drain hose can be extended using a connection piece to attach a further length of hose The drainage length must not be longer than 4 m and the delivery head must not exceed 1 m f the hose is to be directly fitted to the drainage outlet on site use the hose clip supplied see installation diagram The hose can be directed to the left or the right of the appliance The on site connector for the drain hose can be adapted to different widths of hose If the connector protrudes too far into the drain hose it will need to be shortened Otherwise the drain hose may become blocked The drain hose must not be shortened N Make sure that there are no kinks in the hose and that it is not squashed or stretched 74 Venting the drainage system If the on site drain connection is situated lower than the guide path for the bottom basket rollers in the open door the drainage system must be vented Otherwise a siphoning effect during a programme can cause the appliance to empty itself of water To vent it m Open the dishwasher door fully m Pull the lower spray arm firmly upwards to remove it m Cut off the top of the vent valve in the wash cabinet Technical
16. important that this basic safety requirement is present and regularly tested and where there is any doubt the electrical system in the house should be checked by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock gt Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating Warning and Safety instructions P This equipment may only be installed in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer P The plastic housing of the water connection contains an electrical component The housing must not be dipped in water P There are live wires in the water inlet hose Never cut the water inlet hose even if it is too long gt The integrated Waterproof System offers protection from water damage provided the following conditions are met The dishwasher is correctly installed and plumbed in The dishwasher is properly maintained and parts are replaced where it can be seen that this is necessary The tap has been turned off when the appliance is not used for a longer period of time e g during holidays The Waterproof system will work even if the appliance is switched off However the appliance
17. menu F External water softening system If your dishwasher is connected to an external water softening system which uses salt to reactivate to achieve good cleaning results you will still need to set the water hardness level of the water softening unit on the dishwasher to the water hardness level of the water supplied from the external water softening system If you do not know what this is then set the value at 1 4 mmol l 8 d German scale m Select the value which equates to the water hardness level of the water supplied by the external water softening unit and confirm your selection with OK If you disconnect the dishwasher from the external water softening system select the Autarnatic option Rinse aid You can adjust the rinse aid dosage for best results The rinse aid dosage can be set from approx 0 6 ml The factory default setting is 3 ml If spots appear on crockery and glassware Increase the rinse aid dosage If clouding or smearing appears on crockery and glassware Decrease the rinse aid dosage m Use to select the rinse aid dosage you want and confirm with DIE 80 Check filters You can adjust the interval at which the message to remind you to check the filters appears You can set an interval of between 30 and 60 programme cycles The Check filters message is set at the factory to appear after every 40 programme cycles m Select the interval you want
18. must remain connected to the electricity supply 10 P A damaged appliance could be dangerous If the dishwasher gets damaged switch it off at the mains and call your Miele Chartered Agent or the Miele Customer Contact Centre P Unauthorised repairs could result in unforeseen dangers for the user for which Miele cannot accept liability Repairs should only be undertaken by a Miele approved service technician P Faulty components must only be replaced by genuine Miele original spare parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used P Always disconnect the dishwasher from the electrical supply for maintenance work switch off at the wall socket and remove the plug D If the connection cable is damaged it must be replaced with a Miele cable by a Miele approved service technician only P In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Warning and Safety instructions Installation P The dishwasher must be installed and connected in compliance with the installation instructions D The dishwasher must be correctly aligned to ensure problem free operation P In order to ensure stability built under and integ
19. no danger to children while being stored for disposal You can also contact your Chartered Agent for advice It should be unplugged or disconnected from the mains electricity supply by a competent person To enable sorting by type of plastic for recycling all plastic parts of the appliance are labelled with international standard symbols Caring for the environment Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity You can make the most of your appliance by following these tips m For most economical dishwashing make full use of the baskets without overloading the dishwasher m Choose the programme to suit the type of crockery being washed and the degree of soiling m Select the Marmal programme for energy saving dishwashing m f your household water system is suitable this dishwasher can be connected to a hot water supply Select Without heater when washing lightly to normally soiled dishes The water will not be heated in this programme However because the water is not heated drying results may not match those of other programmes m Follow the detergent manufacturer s recommendations on detergent dosage m When using powder or liquid detergent you can use less detergent if baskets are only half full 14 Before using for the first time To open the door To close the door m Push the baskets right in m hen raise the door upwards
20. obstructed m Switch the dishwasher on using the button The main menu will appear in the display If the memory function is activated the programme menu for the programme last selected will be displayed instead see Settings menu Memory Sensor wash Quick wash T 40 C hain menu Select a programme 36 Choose your programme according to the type of load and how dirty it is The different programmes and their uses are described in the Programme chart later on in this booklet m Use the selector buttons to select the programme you want The display will change to show the programme menu Sensor wash Extras Pressing the i button will call up some information about the programme currently selected Operation You can now specify the type of dishwasher detergent you use You can choose normal detergent 2 in 1 tabs or Combi tabs see Settings menu Detergent type Selecting Extra options You can now select Extra options for your chosen programme m To do this first select the Extras option in the menu The Extras available for your programme will appear in the display The following extras are available Turbo For shortening the programme duration In order to achieve optimum results consumption rates increase with this option When used together with the Quick wash programme the Turbo function operates a cycle without heat to rinse crockery if
21. on using the On button The On indicator light comes on m Select the programme you want from the main menu m Select the Delay start 4 function The current time of day and the last start time selected will appear in the display The display will also show the end time for the programme The lt gt indicator light will come on Start time Finish at 13 32 m Use to set the time you want the programme to start at If the button is kept pressed in the time will automatically decrease or increase The end time alters automatically 41 Additional functions m Confirm the start time with OK The display will change to show the programme menu m Select Start m Close the door When the set time is reached the programme selected will begin automatically The indicator light will go out Starting a programme before the start time has been reached 42 You can start a programme before the set start time has been reached Proceed as follows m Open the door m Select Cancel and confirm with OE The lt gt indicator light will go out Sensor wash 12 00 Programme finished Main menu m Select Main menu m Select the programme you want m Select Start m Close the door The In operation indicator lights up The programme starts Cleaning and care Check the condition of your dishwasher regularly approx every 4 6 months This way faults and problems can be avoided
22. swallowed or inhaled detergent Warning and Safety instructions Technical safety P Before setting up the appliance check it for any externally visible damage Under no circumstances should you use a damaged appliance A damaged appliance could be dangerous D The dishwasher must only be plugged into the electricity supply via a suitable switched socket The electrical Socket must be easily accessible after the dishwasher has been installed so that it can be disconnected from the electricity supply at any time See Electrical connection P There must be no electrical sockets behind the dishwasher Danger of overheating and fire risk if the dishwasher were to be pushed up against a plug gt The dishwasher must not be installed under a cooktop The high radiant temperatures which are sometimes generated by a cooktop could damage the dishwasher For the same reason it should not be installed next to open fires or other appliances which give off heat such as heaters etc P Do not connect the dishwasher to the mains supply until it has been fully installed P Before connecting the appliance check that the connection data on the data plate voltage and connected load match the mains electricity supply If in any doubt consult a qualified electrician P The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system It is most
23. there is a bluish sheen on the surface of glassware film can be wiped off Possible cause The dishes were not loaded correctly See notes in Loading the dishwasher The programme was not powerful enough Select a more intensive programme See Programme chart There is some stubborn soiling although most of the crockery is only lightly soiled e g with tea stains Use the Adjust Sensor wash setting see Settings menu Pr Adjust Sensor wash Not enough detergent was dispensed Use more detergent or change your detergent Items are blocking the path of the spray arms Rearrange the items so that the spray arms can rotate freely The filter combination in the base of the wash cabinet is not clean or is not correctly fitted This may cause the spray arm jets to get blocked Clean and or fit the filter combination correctly Clean the spray arm jets See Cleaning and care The non return valve is open and blocked Dirty water has flowed back into the wash cabinet The rinse aid dosage is set too high Clean the drain pump and the non return valve See Maintenance Cleaning the drain pump and non return valve Reduce the dosage see Settings menu Rinse aid 55 Problem solving guide Dishes cutlery and glasses are not dry or are flecked White residue is visible on cutlery and crockery clouding occurs on glassware film can b
24. up to 10 acid content The resulting rinsing and drying quality will not however be as good as when rinse aid is used Do not use vinegar with a higher acid content e g vinegar essence 25 acid This would damage the dishwasher If you only ever use combination products containing rinse aid in your dishwasher you do not need to add rinse aid 21 Before using for the first time Rinse aid indicator When the Rinse aid low message appears the reservoir contains sufficient rinse aid for 2 3 programmes only m Add rinse aid in plenty of time If the 2 in 1 or Combi tab function has been selected the Rinse aid low message will not appear see Settings menu Detergent type m Confirm with DE m Add rinse aid only until it is visible in The Rinse aid low message will go the opening out The rinse aid reservoir holds approx 110 ml m Close the flap firmly so that it clicks into place Otherwise water can enter the rinse aid reservoir during a programme m Wipe up any spilled rinse aid This prevents over foaming occurring during the next programme You can adjust the rinse aid dosage for best results see Settings menu P Rinse aid 22 Loading the dishwasher Note Remove coarse food residues from crockery There is no need to rinse items under running water ADo not wash items soiled with ash sand wax lubricating grease or paint in the dishwasher
25. CD OI ER ETOILE ee dave een 39 Unloading the dishwasher 39 Interrupting a Programmes eder ra aee eee eae 39 Changing a programme 40 Additional functions 41 Delay start asas space need RES P tae Riek PRAET uam Sn A equ 41 Cleaning and care 43 Cleaning the wash cabinet 43 Cleaning the door and the door seal 43 Cleaning the reflector panel 43 Cleaning the control panel and door front 44 Checking the filters in the wash cabinet 45 Cleaning thetilierSs isse sacer tadas ado Rex REO XE RR ERE RR AUR RS de bee 45 Cleaning the spray arms 47 Problem solving guide 48 Techniealproblems x xus etie egeo x a anne 48 The dishwasher does not fill drain isses 50 General problems 2 52 NOISES e aromates o ee cake P aee d a eed ee en 54 Unsatisfactory washing result 55 Maintenance o ode e EE Seen RU Rte as deed tet ae dead 58 Cleaning the water inlet filter 58 Cleaning the drain pum
26. Display The duration of the programme selected appears in hours and minutes in the display before the programme begins During the programme the time left until the end of the programme is displayed The time displayed may vary with the same programme This is partly because of the water temperature at each intake the reactivation cycle and partly because of the amount of crockery and how dirty it is When a programme is selected for the first time the display shows an average time for a cold water intake The times shown in the Programme chart refer to standard test loads and temperatures Each time a programme is run the electronic unit takes the new conditions into account and calculates the time required To save energy the display goes out after 10 minutes if you do not touch any sensors during this time Touching any sensor will switch the display back on again except for the button O Operation Programme finished At the end of a programme the in operation indicator light flashes on and off slowly It is visible even with the door closed It will stop flashing one hour after the programme has finished If the message Programme finished or Drying plus comes up in the display and the door has opened slightly this indicates that the programme has finished You can now empty the dishwasher If you have deselected the auto matic door opening function see Settings menu Drying plus
27. LES LSA FIN L DIN amp LEA pP SS NZ SES If spoon handles do not fit between the holders then lay them the other way round m Arrange the cutlery in the tray as shown To make unloading much easier cutlery should be grouped in zones one for knives one for forks one for spoons etc Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs off them freely The upper spray arm must not be blocked by items which are too big The cutlery tray inserts are removable For example you can remove one insert to make room for larger items of crockery in the upper basket 31 WeS S2223 CESSE een 22 lum 36265 HEN IZ and distribute them Sememe g J 8535858 S SESTESESS required m Fit it into the cutlery basket if ER ER ERS A VE D er SSS ASS SNS slots to either side of the cutlery down in the basket will come out basket Loading the dishwasher Cutlery basket depending on model forks should be placed with the handles upwards in the basket However cutlery placed handle cleaner and drier Use the insert supplied for heavily soiled spoons m To avoid the risk of injury knives and Cutlery insert for the cutlery basket m Place small spoons in the individual The insert separates the items so that evenly along the insert they can be more easily
28. Miele Operating instructions VE SR A ir Nas INA ri i Ex 7 for dishwashers To avoid the risk of accidents or damage to the appliance it is en AUS NZ essential to read these instructions as well as the installation plan before it is installed and used for the first time M Nr 07 600 690 Contents Guide to the appliance 5 Appliance overview 0 teeta 5 Control panela E 6 DISEASE PRETI ITI 7 Warning and Safety instructions 8 Caring for the environment 13 Disposal of the packing material 13 Disposal of your old appliance 13 Energy saving Washilig uci ee Rr detecte e qon deos At aa ec 14 Before using for the first time 15 TOPONIMO ACO Meare O el Feen Mee WERE 15 TO ClOS6 INE TOO uuu aaa n po rt er db epe a tar ce 15 Setting the language 16 Glock display s a RI E Ee E eie 16 Setting the time of day 17 Before using the appliance for the first time you require 18 External water softening system 18 Filling the salt reservoir 26 RI 18 Insufficient salt indication iilii 20 RINSS AIT 2 Se o
29. The Without heater programme if available requires a hot water supply of between 45 C minimum and 60 C maximum The higher the water intake temperature the better the cleaning and drying results The inlet hose is approx 1 5 m long A 1 5 metre long flexible metal extension hose pressure tested to 14000 kPa 140 bar is available as an optional accessory if required 72 Atap with a 3 4 male thread must be provided on site The dishwasher is constructed to comply with Australian regulations and may be connected to a suitable supply without an extra non return valve if national regulations allow this The water pressure flow pressure at the take off point must be between 30 and 1000 kPa 0 3 and 10 bar If the water pressure is lower than this the fault message Water inlet fault will appear in the display see Problem solving guide If the water pressure is too high a pressure reducer valve must be fitted NTo avoid any damage to the appliance the dishwasher must only be connected to a fully vented plumbing system Plumbing IN The inlet hose must not be shortened or damaged in any way as it contains electrical components see Illustration This appliance incorporates back flow protection complying with AS NZS 3500 1 2 No further backflow protection required for connection to the water supply 73 Plumbing Drainage The appliance drainage system is
30. The tap is closed Open the tap fully Before rectifying the problem you must Switch the dishwasher off with the Off button Q Fault F12 F13 Water intake is restricted Open the tap fully Check the water inlet filter and clean it if necessary see Maintenance The water pressure at the intake is lower than 30 kPa 0 3 bar Seek professional advice Problem solving guide The In operation indicator is flashing quickly In the Without heater programme the following message appears Water intake temp too low The In operation indicator is flashing quickly The buzzer is sounding The following message appears in the display Drain fault F11 Possible cause The intake water has not reached the required temperature of 45 C see Connection to the water supply Remed Start the programme again If the fault message appears again select a different programme Before rectifying the problem you must Switch the dishwasher off with the Off button O Water outlet is restricted water remains in the wash cabinet at the end of a programme Clean the filter combination See Cleaning and care Clean the drain pump See Maintenance Clean the non return valve See Maintenance Remove any kink in the drain hose Remove drain hose and check for any blockages in the drain pipe 51 Problem solving guide General problems Pr
31. These materials will cause damage to the dishwasher Crockery can be loaded anywhere in the baskets but the following notes should be observed Do not place crockery and cutlery inside other pieces where they may be concealed Load the crockery so that water can access all surfaces This ensures that they get properly cleaned Make sure that all items are securely positioned Hollow items such as cups glasses pans etc must be inverted in the basket Tall narrow hollow items e g champagne glasses should be placed in the centre of the basket to ensure better water coverage Wide based items should be placed at an angle so that water can run off them freely The spray arms must not be blocked by items which are too tall or hang through the baskets If in doubt test for free movement by manually rotating the spray arms Make sure that small items cannot fall through the holders in the baskets Small items e g lids should therefore be placed in the cutlery tray or cutlery basket depending on model Some foodstuffs may contain natural dyes e g carrots tomatoes or tomato sauce Plastic items in the dishwasher may discolour if large quantities of these foodstuffs find their way into the appliance on the crockery The stability of plastic items is not affected by this discolouration 23 Loading the dishwasher Items not suitable for dishwashers Wooden cutlery and crockery or
32. ans T shortened cycle dried on soiling non sensitive crockery gt acer abur nous and cutlery food residues gt maximum wash power shortened cycle 1 Potatoes rice noodles or stews can leave starchy soiling on crockery Meat fish eggs or casseroles can leave albuminous soiling on crockery 64 Programme chart Programme Detergent Compartment Compartment II gt gt gt gt 2 see Detergent 3 Sometimes tabs don t fully dissolve 65 Programme chart Programme Programme sequence Pre wash Main wash Interim rinse Final rinse Drying id 1 2 is Sensor wash Variable programme sequence sensor controlled adjustment to amount of crockery and soiling if required 45 65 if required 65 X Quick wash 40 C 40 X 45 xe Sensor wash Variable programme sequence with glass care gentle Y sensor controlled adjustment to amount of crockery and soiling if required 40 48 if required 55 X Energy save 40 65 X Light soiling 50 C 50 65 X Normal x 50 50 x Intensive 65 C X 65 65 X Pots amp pans 75 C X 15 65 X 1 Standard programme for energy labelling 2 The drying phase continues for a further 20 minutes as long as the door is kept closed at the end of the programme cycle 66 Programme chart Consumption Duration Energy Water Cold w
33. appliance or to update 3 Clear sensor lt C programming data in the future For navigating back to the previous menu or deleting values which have been set previously Delay start button with indicator light For selecting the delay start function 2 Display See next page for more information 9 In operation indicator light Shows if a programme is running when the door is shut Sensor i Information button For displaying additional information about the option selected This instruction book applies to several different dishwasher models The specific dishwasher models below are referred to as follows G 1674 etc G 1XXX G 2674 etc G 2XXX The model numbers G 1XXX and G 2XXX used in this book refer to the model designation specified on the data plate of the appliance and not the description on the control panel The data plate is located on the right hand side of the door Guide to the appliance Display CEEA Pl A ejened s Seranne P The display is used to select the following the programme extras the delay start time the Settings menu P information During a programme the display shows the following the name of the programme the current time of day the stage the programme is at the estimated time left for the programme to run any relevant fault messages and notes To save energy the display goes out after 10 minutes if you do not pre
34. approx 20 seconds This will enable the temperature in the wash cabinet to settle Then raise the door upwards until the catch engages 39 Operation Changing a programme 40 If the detergent dispenser flap has already opened do not change the programme If a programme has already started and you wish to change it proceed as follows m Open the door Sensor wash 32 12 00 hain wash Cancel m Select Cancel and confirm with OK The programme will be cancelled Sensor wash 12 00 Programme finished Nain menu m Select the Main menu option The display will revert to the main menu m Select the programme you want m Select Start m Close the door The In operation indicator lights up The programme starts Additional functions Delay start The start time of a programme can be delayed e g to benefit from economy rates of electricity A delay start time of between 15 minutes and 24 hours can be selected The delay start time is set in 15 minute steps NWhen using the Delay start function make sure that the detergent compartment is dry before adding detergent Wipe dry with a cloth if necessary If the compartment is wet powder detergent can become lumpy and stick to the dispenser with the result that it is not fully dispensed Do not use liquid detergent when selecting Delay start as it can run into the dishwasher before it is required m Open the door m Switch the dishwasher
35. ass care system 68 Programme chart Programme sequence Consumption Duration Energy Water Pre Main Interim Final Drying Cold Hot Litres Cold Hot wash wash rinse rinse water water water water Le 1 2 C 20 C 60 C 20 C 60 C kWh kWh h min h min 70 X 70 X 1 35 1 05 13 2 14 2 05 X 0 01 0 01 4 0 13 0 13 2X X X X X 0 05 26 1 26 X 75 X 65 X 1 40 1 15 13 2 29 2 16 x 45 X 65 X 0 85 0 60 13 2 07 1 55 X 65 X 65 X 1 00 0 65 13 1 52 1 39 35 X 55 X 0 50 0 30 10 0 49 0 41 25 X X 0 20 10 0 17 The durations given can vary depending on individual circumstances 69 Optional accessories To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele Chartered Agent or from the Spare Parts Department some may be supplied as standard depending on model If you would like to you will need to order Wash long stemmed glassware a glassware insert for the upper basket wash a Miele Cappuccinatore a Cappuccinatore insert for the upper basket small plates baby bottles and small items in the upper basket a multi function basket for the upper basket different sized plates cups and glasses in the upper basket a vario insert for the upper basket wash bottles e g milk or baby bottles a bottle holder
36. ater Hot water Litres Cold water Hot water 20 C 60 C 20 C 60 C kWh kWh h min h min 0 95 1 35 0 70 1 00 8 17 1 30 2 38 1 18 2 21 0 55 0 20 10 0 38 0 27 0 70 0 95 0 40 0 50 10 17 1 26 2 02 1 17 1 43 1 10 0 75 10 2 06 1 55 1 05 0 75 10 1 36 1 23 0 84 0 41 12 7 2 32 2 18 1 25 0 95 13 2 19 2 06 1 50 1 10 13 2 38 2 27 The durations given can vary depending on individual circumstances 67 Programme chart Programme When to use Hygiene Programme with special parameters for hygienic removal of bacteria from baby bottles chopping boards utensils etc Pre wash For rinsing crockery to avoid smells if a complete cycle is not yet needed Without heater Y Only for use with hot water connection of at least 45 C for lightly to normally soiled crockery includes sensor controlled glass care system Pasta Paella Raclette For removing dried on soiling like pasta paella or raclette add 20 more detergent than recommended for a full load Plastics Y To gently wash dishwasher proof plastic containers includes sensor controlled glass care Tall items 65 C For very large heat resistant items e g tall vases Glasses warm Y For cleaning glassware without rinse aid and without detergent includes sensor controlled glass care system Glasses quick Y For rapid cleaning of glasses for immediate use again without rinse aid or detergent includes sensor controlled gl
37. d marinades Aluminium components e g grease filters must not be cleaned with caustic alkaline commercial or industrial cleaning agents These may damage the material or in extreme cases cause a severe chemical reaction See section Adding detergent for information on suitable detergents Loading the dishwasher Upper basket NFor safety reasons do not operate the dishwasher without the upper and lower baskets in place except when using the Tall items 65 C program m Use the upper basket for small lightweight and delicate items such as cups saucers glasses dessert bowls etc Shallow pans or casserole dishes can also be placed in the upper basket m Long items such as soup ladles mixing spoons and long knives should be placed lying down across the front of the upper basket Removable spiked insert The spiked insert can be removed to make more room for larger items such as casserole dishes LIM IIL 7 AB SER EESSL 1 lt 2 BS y UG wi LY GU A ay hi if i I 20 a H g IM A IN IN Z Y Y amp LU DES PNAS To remove the insert m Pull it upwards by the handle as shown BS To replace the insert m Fit the insert into the lower basket with the hooks going under the cross piece as illustrated m Press down on the handle until the insert is held securely in position 25 Loading the dis
38. deactivated m Select the option you want and confirm with CIC 82 Temperature The temperature can be displayed in C Celsius or F Fahrenheit The factory default setting is C m Select the option you want and confirm with OE Settings menu F Buzzer When the buzzer is activated an audible tone sounds atthe end ofa programme and when there is a fault The buzzer is activated as standard at the factory Buzzer at the end of a programme You will hear the buzzer at the end of a programme in bursts of five with a short pause in between The buzzer will continue to sound for up to an hour if you do not switch the dishwasher off Buzzer when there is a fault In the event of a fault the buzzer will sound continuously The buzzer will continue to sound for up to two minutes if you do not switch the dishwasher off or correct the fault The buzzer will still sound if there is a fault even if it has been deactivated Setting the buzzer volume You can select one of two options or deactivate the buzzer Off The buzzer at the end of a programme is deactivated Mormal The buzzer sounds at a normal volume Loud The buzzer sounds louder m Select the volume you want or deactivate the buzzer m Confirm with DE 83 Settings menu F Keypad tones An audible tone sounds each time a button is pressed There are seventeen different volume settings The factory default s
39. e dnp eee GY ack ee Sia Te ER E ER rats 21 Adding rinse ald erica di gud heed bbe d hd oe ohne ek beet oa e een 21 Rinse ald Indleaters sess op ac Qo EEE ES SUN aca BO ed doloe e Paid 22 Loading the dishwasher 23 Items not suitable for dishwashers 24 Wpper Baskets E PMID TT 25 Removable Spiked Insert use eser ERE a CR Re 25 HIAgEAEUPTACK ass act ng NAO 26 Positioning rail depending on model 26 SUPPOMN Malle citrato eed ated eed Pade bine secede duh e 27 Adjusting the upper basket cesses rra eer chm e due ae 28 Lower basket san as testen Eae adobe eios ten 29 Mario IFISertS us aci oe gen nh Lied Bat eR USA ind Bei dedo qr s 29 Bottle holder ix austragen pu wae pubs Gea ped pA E nee 30 A Rd Mus ni era ee 31 Cutlery tray depending on model 0 0 00 00 eee 31 Cutlery basket depending on model 1 32 Contents Operation lt lt vcd Seidio tien 33 Degen amp s rd re eruta wade ed aan ne Has DARE e d UR nei ps 33 Adding detergen e era o a in a leder te REA SR wit cn d 35 Switching ON 44044 4 0 36 Select a programme ooo 36 Selecting Extra options 0 0 0 e 37 Start tie Drograrmmmie cvs e EE ETE p 38 PIS layer Pi EA gece anda tases hd hae neh webu aM ata he A 38 Programme finished 24 coude ox egy e xe Rer wx Rd ue LR RE ded 39 SW
40. e programme sequence and duration will be adjusted for the type of detergent selected Depending on the programme the duration can be considerably longer Normal When using normal detergent you must add salt and rinse aid see Filling the salt reservoir and Adding rinse aid The rinse aid refill reminder is active with this setting 2 in 1 Select the 2 in 1 function if you are using 2 in 1 tabs detergent containing rinse aid The programme sequence will be adjusted and rinse aid will not be dispensed in the programme The Rinse aid low message is also deactivated 78 Combination tabs Select the Combi tabs function if you are using Combi tabs detergent containing rinse aid and salt substitutes as well as other components where applicable e g 3in 1 4 in 1 tabs The programme sequence will be adjusted and rinse aid will not be dispensed in the programme The Replenish rinse aid message is also deactivated When using Combi tabs you must still keep the salt reservoir replenished See Filling the salt reservoir Salt consumption in the water softener is reduced to between and of the normal amount Do not select the Combi tabs function if using 2 in 1 tabs detergent with rinse aid your water hardness level is above 3 8 mmol l or 21 d Follow the detergent manufacturer s instructions The cleaning and drying performance of these types of detergent can vary enormo
41. e the ratchet Then unscrew the spray arm m Remove the lower basket m Pull the lower spray arm firmly upwards to remove it m Use a pointed object to push food particles into the spray arm jets m Rinse thoroughly under running water m Replace the spray arms and check that they rotate freely 47 Problem solving guide With the aid of the following guide minor problems can be easily corrected without calling in a Miele service technician saving you both time and money N Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations Unauthorised or incorrect repairs could cause personal injury or damage to the appliance Technical problems Problem The dishwasher does not start The dishwasher stops After the programme has started the In operation indicator light is not visible 48 Possible cause The door is not properly closed Remed Push the door firmly shut The appliance is not plugged in Insert the plug and switch on at the socket The fuse is defective or has tripped Reset or replace the fuse Minimum fuse rating see data plate The appliance is not switched on Press the On button and select a programme A programme has not been selected The fuse is defective or The reflector panel was not correctly fitted Select the program
42. e wiped off 56 Possible cause The amount of rinse aid may be insufficient or the rinse aid reservoir empty Remed Replenish the reservoir increase the dosage or change the brand of rinse aid See Before using for the first time Crockery was taken out of the cabinet too soon Leave it in for longer See Operation Combi tabs have been used which have impaired drying performance Set the Detergent type to Normal and fill the rinse aid reservoir with rinse aid See Settings menu Detergent type The dishwasher has been set for 2 in 1 or Combi tabs even though this type of detergent has not been used Not enough rinse aid was used Set the Detergent type for the product being used see Settings menu Detergent type Reduce the dosage see Settings menu Rinse aid There is no salt in the salt reservoir Fill the salt reservoir See Before using for the first time Filling the salt reservoir An unsuitable combination detergent has been used Change your detergent Use a standard liquid tablet or powder detergent There is a fault with the automatic water softening system Call the Miele Customer Contact Centre Problem solving guide Glassware has a brown or blue tinge and film cannot be wiped off Glassware is dull and discoloured film cannot be wiped off Tea or lipstick stains have not been completely removed
43. elopments become available Comparison tests Test standard Standard programme for energy label comparison tests Capacity Amount of detergent Rinse aid dispensing Drying measurements Loading examples AS NZS 2007 1 2005 AS NZS 2007 2 2005 AS NZS 6400 2005 Normal 12 14 place settings depending on model 12 place settings 5g in compartment 25g in compartment Il 14 place settings 5g in compartment I 27 5 g in compartment Il Setting 3 approx 3 ml Door ajar using a block of approximately 50 mm upon completion of dry test Pictures illustrating how to load the dishwasher are shown on the following pages 61 Comparison tests Model types G 1xxx with a cutlery tray 12 place settings Cutlery tray 62 Comparison tests Model types G 2xxx with a cutlery tray 14 place settings Cutlery tray 63 Programme chart Crockery type Soiling Programme on variable MEL il sensor controlled wash non sensitive crockery gt none saling gt shortened cycle glasses and plastic containers sensitive to gt gt short cycle high temperatures light soiling variable gt gt sensor controlled wash with glass care gt average programme values shortened cycle mixed crockery gt normal lightly dried soiling gt water and energy saving cycle very high wash gt performance heavyly soiled pots p
44. er out ofthe cabinet m Remove all foreign objects from the using a suitable container or utensil drain pump watch out for glass or bone splinters which are particularly difficult to detect and could cause injury Turn the drain pump impeller by hand to check that there are no more obstructions You will feel a little resistance when you turn the impeller m Carefully replace the non return valve and secure it with the catch N Ensure that the catch engages correctly m Press the catch for the non return valve inwards D m Lift out the non return valve and rinse well under running water m Remove all foreign objects from the non return valve 59 After sales service Repairs In the event of any faults that you cannot remedy yourself please contact 60 Your Miele Chartered Agent or the Miele Customer Contact Centre You find the telephone number of the Miele Customer Contact Centre on the back cover of the manual When contacting your Chartered Agent or the Miele Customer Contact Centre please quote the model type and number of your appliance both of which are shown on the data plate on the right hand side of the door Future updates The programme update function is designed to enable a service technician to update your appliance s electronics in keeping with advances in technology Information regarding programme updates will be made known by the Miele Company as and when such dev
45. etting is 8 m Select the volume you want and confirm this with OF Brightness There are seventeen different display brightness settings The factory default setting is 9 m Select the brightness you want and confirm this with OF 84 Memory You can use the Memory function to save the last programme selected Instead of the main menu the last programme selected will appear in the display when the dishwasher is switched off and back on again at the end of a programme or the door is opened and then closed The dishwasher is delivered with the Memory function activated m Select the option you want and confirm this with OK Settings menu F Showroom programme The programme is for display use only The dishwasher is fitted with various demonstration programmes for showroom use The Demo mode and Demo mode in continuous loop programmes demonstrate operation and functions Demo mode This programme is started by pressing any button It will run through once and then has to be started again Demo mode in continuous loop This programme will begin as soon as you switch it on and then will play in a continuous loop until you switch it off Demo with sound This programme activates the pumps to demonstrate the sound of the dishwasher Demo programme Using for the first time is disabled in the display Drying plus demo The door will open automatically To switch Demo mode on
46. f it appears during a programme wait until the end of the programme m Confirm with OE The Replenish salt message will go out After the salt reservoir has been filled the Insufficient salt message may still appear in the display if the salt concentration has not yet reached the correct level If this is the case confirm again with Dk The salt indicator is deactivated when the dishwasher registers a water hardness level below 0 7 mmol l 4 d NRun the Quick wash programme immediately without any crockery in the dishwasher and without selecting the Turbo extra option to remove any traces of salt from the cabinet Before using for the first time Rinse aid Adding rinse aid Rinse aid is necessary to ensure water m Press the button on the lid of the salt does not cling and leave marks on reservoir in the direction of the arrow crockery during the drying phase and until the flap springs open helps crockery dry faster after it has been washed Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically Inadvertently filling the rinse aid reservoir with powder or liquid detergent will damage the reservoir Only pour rinse aid formulated for domestic dishwashers into the reservoir Otherwise you will cause serious damage to the reservoir Alternatively it is possible to use household vinegar with a max 5 acid content or liquid citric acid
47. f the wires in the mains lead of this appliance do not correspond with the coloured markings identifying the terminals of your plug proceed as follows m The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol L or coloured green or green and yellow m he wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N or coloured black m he wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter A AUSTRALIA WARNING THIS APPLIANCE MUST BE EARTHED 71 Plumbing The Miele waterproof anti leak system Providing your dishwasher has been installed correctly the Miele waterproof anti leak system will protect you from water damage throughout its lifetime Connection to the water supply N Water in the dishwasher must not be used as drinking water The dishwasher may be connected to a cold or hot water supply max 60 C We would only recommend connection to a hot water supply if it is economical e g a solar powered supply When connected to a hot water supply all programme stages which would otherwise be carried out with cold water will be carried out with hot water AA warm water connection with temperatures exceeding 60 C may cause damage to the unit impair wash results and affect the product guarantee
48. he water which is supplied from the external water softening system If you do not know what this is then set the value at 1 4 mmol l 8 d see Settings menu External water softener 18 Filling the salt reservoir In order to achieve good cleaning results the dishwasher needs to operate with soft water Hard water results in the build up of calcium deposits on crockery and in the dishwasher Mains water with a hardness level higher than 0 7 mmol l 4 d German scale needs to be softened This takes place automatically in the integrated softener unit The softener unit is suitable for a water hardness level of up to 12 6 mmol l 70 d It requires dishwasher salt If you use combination products which have salt in them in your dishwasher such as 3 in 1 or 4 in 1 products you should still add salt in order to achieve optimum results and to ensure that the water softener continues to function correctly Selecting the Combi tabs option reduces salt consumption to between and of the normal amount See Settings menu F Detergent type Before using for the first time You can check the water hardness level m When filling the salt reservoir only measured by the water softener sensor open the door halfway to ensure in the display see Settings menu P that all the salt gets into the reservoir Water hardness If the water hardness in your area is constantly lower than 4 d 0 7 mmol
49. hwasher Hinged cup rack m To make room for tall items raise the rack upwards G 2XXX models You can set the cup rack at two different heights m Pull the cup rack upwards and click it back into position at the required height 26 Positioning rail depending on model Glasses can be arranged along the positioning rail to give them some support during the programme Ig l 2 YA A i N Pa i e m Raise the rail and lean the glasses against it The positioning rail can be flipped over to the middle of the basket for easy sorting and removing of crockery Loading the dishwasher Support rail This support is designed to hold tall glasses and glasses with stems securely m Lower the support and lean tall glasses against it m You can also remove a section of the cutlery tray to make more room for tall glasses 27 Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket the following plate dimensions In order to gain more space for taller 9 P can be accommodated pieces of crockery in the bottom or upper basket the upper basket can be adjusted on three levels with 2 cm between each level Dishwasher with cutlery tray see data plate for model number The upper basket can also be set at an Upper Plate in cm angle with one side high and the other basket Uppe
50. ings will be saved in memory after the dishwasher has been through one complete programme After you have confirmed the minute entry with OE two messages will appear in the display The Insufficient salt and Rinse aid low messages may also appear to remind you to fill the salt and rinse aid reservoirs See relevant sections for how to do this After you have confirmed these messages with DK the display will change to show the main menu Sensor wash A Main menu Quick wash Y 40 C You can now select a programme and start it or switch the dishwasher off Before using for the first time Before using the appliance for the first time you require Approx 1 kg dishwasher salt Domestic dishwasher detergent Rinse aid formulated for domestic dishwashers Every dishwasher is tested at the factory There will be residual water in the appliance from this test It is not an indication that it has been used previously This dishwasher is fitted with a water softener sensor which automatically sets the water softener unit for the local water hardness level External water softening system If your dishwasher is connected to an external water softening system which uses salt to reactivate you will still need to programme the dishwasher to the correct water hardness level to achieve good cleaning results m Set the water softener unit of the dishwasher to the water hardness level of t
51. items with wooden parts these may discolour and fade The glue used in these items is not dishwasher proof and wooden handles may come loose after being washed in a dishwasher Craft items antiques valuable vases and decorative glassware are also not suitable for dishwashers Plastic items which are not heat resistant can melt or lose shape Copper brass tin and aluminium items may discolour or become matt Colours painted over a glaze may fade after a number of washes Clouding may occur on glasses after frequent washing Do not wash delicate glassware or glassware containing lead crystal in a dishwasher 24 We recommend When purchasing new crockery and cutlery make sure they are dishwasher proof If delicate glassware is washed in the dishwasher ensure that only very low temperatures are used see programme chart or a special glass care programme is used depending on model This will reduce the risk of clouding Wash particularly delicate glassware by hand Please note Silverware previously cleaned with a silver polish may still be damp or spotted at the end of a programme where water has not run off smoothly It may need to be rubbed dry with a soft cloth It may need to be rubbed dry with a soft cloth Silver which has been in contact with foods containing sulphur can discolour These include egg yolk onions mayonnaise mustard pulses fish fish brine an
52. l you do not need to add salt The salt refill indicator will be deactivated automatically Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener m Press the button on the lid of the salt reservoir in the direction of the arrow until the flap springs open N Miele recommends using specially designed dishwasher salt to maximize the performance of your dishwasher and to prevent build up of calcium and limescale in the dishwasher cabinet especially if you live in hard water area Dishwasher salt can be purchased online at www miele shop com depending on country or via the Miele Spare Parts Department m Lift up the funnel Before using for the first time Do not fill the reservoir with water m Add salt only until the reservoir is full or until water runs out of the opening The salt reservoir holds approx 1 kg of salt Do not add any more than 1 kg of salt As the salt reservoir is filled displaced water may overflow m Clean any excess salt from around the reservoir opening and then close the flap m Run the Quick wash programme im mediately without any crockery in the dishwasher and without selecting the Turbo extra option to remove any traces of salt from the cabinet 20 Insufficient salt indication m Fill the salt reservoir with dishwasher salt for reactivation when the Insufficient salt message appears I
53. me you want Reset or replace the fuse Re fit the reflector panel correctly see Installation diagram Problem solving guide The In operation indicator is flashing quickly The buzzer is sounding One of the following messages appears in the display Technical fault Switch the appliance off turn off the water supply and call the Service Department Waterproof fault Fro Possible cause There may be a technical fault The Waterproof system has reacted Remed Switch the dishwasher off with the Off button O After a few seconds Switch the dishwasher on Select the programme you want Close the door If the fault message appears again there is a technical fault Call the Miele Customer Contact Centre Close the tap Call the Miele Customer Contact Centre Fault with auto door closing The door is sometimes obstructed by an item inside the appliance Remove the obstruction If this is not the case call the Miele Service Dept Fault with auto door opening There may be a technical fault Open the door manually Call the Miele Customer Contact Centre 49 Problem solving guide The dishwasher does not fill drain Problem The In operation indicator is flashing quickly The buzzer is sounding One of the following messages appears in the display Water inlet fault Water inlet fault FAX 50 Possible cause
54. mponent It must not be dipped in water Recommendation If the mains water contains a large amount of insoluble substances we recommend fitting a large area filter in the connection between the tap and the water inlet hose threaded union This filter is available from the Miele Spares Parts Department Cleaning the filter m Disconnect the dishwasher from the mains supply Switch off at the mains socket and withdraw the plug m Close the tap m Unscrew the inlet hose 58 m Carefully remove the seal m Withdraw the filter using pointed pliers and rinse clean under running water m Replace the filter and seal making sure they are sitting correctly m Reconnect the inlet hose to the tap making sure it goes on correctly and is not cross threaded m Turn on the tap gradually to test for leaks If there is a leak the inlet hose might not be on securely or it may have been screwed on at an angle Unscrew and reconnect the water inlet valve correctly Maintenance Cleaning the drain pump and non return valve If the water has not been pumped away at the end of a programme the drain pump or the non return valve might be blocked They are however easy to clean m Disconnect the dishwasher from the mains supply Switch off at the mains socket and withdraw the plug m Take the filter combination out of the wash cabinet see Cleaning and cabinet non return valve see arrow m Scoop the wat
55. n of warm water and a little washing up liquid applied with a soft sponge Wipe the surfaces dry using a soft cloth 44 To avoid damaging the outer surface do not use cleaning agents containing soda ammonia acids or chlorides cleaning agents containing descaling agents abrasive cleaning agents e g powder cleaners and cream cleaners solvent based cleaning agents stainless steel cleaners dishwasher cleaner oven sprays glass cleaning agents hard abrasive sponges and brushes e g pot scourers sharp metal scrapers Cleaning and care Checking the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution preventing it accessing the circulation system and re entering the cabinet through the spray arms This dishwasher must not be used without all the filters in place Collection of coarse soil may cause the filters to clog The level of soiling and time it takes before the filters need cleaning will vary depending on use The message Check filters will appear in the display after every 40 programme cycles factory default setting You can set the interval for this message to appear to between 30 and 60 programme cycles see Settings menu F Check filters m Check the filter combination m Clean it if necessary m Then confirm the message with OF The display will change to show the main menu
56. ngs Time m Select the option you want to change Pressing the i button will call up some information about the programme currently selected Sub menu options which have already been set will have a tick v beside them Settings menu F Language F The display can be set to appear in one of several different languages You can change the language for the display via the Language I sub menu m Select the language you want and confirm this with DF The flag after the word Language I acts as a guide if a language which you do not understand has already been set If this is the case keep selecting the option which has a flag after it until you reach the Language sub menu Time of day Select either a 24 hour or 12 hour clock and then set the current time of day Clock display m Select the Format option m Select either the 24 hour or 12 hour option and confirm with OE To set the time of day m Select the Set the time option m Set the hours with f and confirm with DIE Then set the minutes After you have confirmed the minutes entry with DIE the display will change back to the previous menu and you can press the C button to return to the Settings I menu 77 Settings menu F Detergent type To ensure excellent results you can programme your dishwasher for the type of detergent you are using You can choose normal detergent 2 in 1 tabs or Combi tabs Th
57. nt residue is blocking the catch This is caused by the drying system and does not indicate a fault Remed Make sure the dispenser is dry before adding detergent Clean the detergent from the catch The moisture will dissipate after a short while Before rectifying the problem you must Switch the dishwasher off with the Off button O The filter combination in the wash cabinet is clogged Clean the filter combination See Cleaning and care The drain pump or non return valve may be blocked Clean the drain pump or the non return valve See Maintenance The drain hose is kinked Remove any kink from the drain hose 53 Problem solving guide Knocking noise in the wash cabinet Rattling noise in the wash cabinet Knocking noise in the water pipes 54 Possible cause A spray arm is knocking against an item in a basket Items of crockery are insecure in the wash cabinet This may be caused by the on site installation or the cross section of the piping Interrupt the programme and rearrange the items which are obstructing the spray arm Interrupt the programme and rearrange the items of crockery This has no influence on dishwasher function If in doubt contact a suitably qualified plumber Problem solving guide Unsatisfactory washing result Problem The dishes are not clean Smearing appears on glassware and cutlery
58. oblem The display is dark The buzzer sounds during a programme The following fault message appears in the display Close the salt reservoir The following fault message appears in the display Middle spray arm blacked or Bottom spray arm blacked 52 Possible cause The display has switched off automatically to save Standby mode The salt reservoir has not been closed properly Items are blocking the path of the middle or the bottom spray arm Press any button Stand by comes to an end Close the flap to the salt reservoir properly If the salt reservoir flap has come undone during a programme you must Switch the dishwasher off with the Off button O and then back on again Start the programme again Open the dishwasher door and rearrange the items which are obstructing the spray arm The middle or bottom spray arm jets are blocked Switch the dishwasher off with the Off button O Then Clean the spray arm See Cleaning and care Problem solving guide Detergent residue is left in the dispenser at the end of a programme The detergent dispenser lid cannot be closed properly At the end of a programme there is a film of moisture on the inside of the door and the interior walls Water remains in the wash cabinet at the end of a programme Possible cause The dispenser was still damp when detergent was added Clogged deterge
59. p and non return valve 59 After sales service 60 REDAS errie mn d e cba t aded eked ated ede ha eee teen os 60 Future updates sene eee Peed cc aia donee ee 60 Contents Comparison tests 61 Programme chart 64 Optional accessories 70 Electrical connection 71 PIUMBING 23 cdo AAPA Reed eek TOL ERA kg Duende etes 72 The Miele waterproof anti leak system 72 Connection to the water supply 72 DEIN AGS Me M IM 74 Technical data 75 Settings MENU torreta 76 To open the Settings menu es steri ri rreak erian EROE ENE EAT ESHA 76 Language A tered E E eed este dupl eae T ee 77 TIME Of day zx edes RE MSNM a Tere Red EHE eee ee et 77 Detergent pes sed Seid e geo ions De E meas dee aah a oa da ate 78 Dring PIUS LR TUIS 79 Waterhardness areas SN er oe es 79 External water softening system 80 als D m 80 Sarl c ERE 80 Adj st Sensor Wash sss sse arpa dida tice p Ru RAE Gow pars 80 Change main Meni Zus eu 22 panoyu manpet a ER Ra KS EON ER dn RR tarde ud 81 DAVE GXIIaS suae ir e ee Wed bp ori Rau ees
60. r basket Lower side low This can be useful to help level asket prevent water collecting in deep dishes G1XXX G2XXX etc Ensure however that the basket To 15 19 34 can be inserted smoothly into the P cabinet It is better to adjust the basket Middle 17 21 29 before loading it Bottom 19 23 27 m Pull out the upper basket Dishwasher with cutlery basket see data plate for model number o i Upper Plate in cm Fu basket Uses al N d Upper basket Lower ES DRE M GAXXX Gaxxx Pesket li Top 20 24 31 Middle 22 26 29 Bottom 24 28 27 To raise the upper basket m Pull the basket up until it clicks into place To lower the upper basket m Pull upwards on the levers at either side of the upper basket m Adjust the basket to the desired height and then push the levers securely back down into position 28 Loading the dishwasher Lower basket Vario inserts The vario inserts are used for washing cups glasses plates saucers pots and pans m For larger and heavier items such as plates serving platters saucepans bowls etc Small items such as saucers can also be placed in the lower basket Do not place thin delicate glassware in the lower basket m Stem glassware e g wine glasses or champagne flutes can be leaned
61. rated dishwashers must only be installed under a continuous worktop which is secured to adjacent cabinetry P If you want to convert your freestanding dishwasher to a built under U model you will need to order the appropriate conversion kit If you remove the existing plinth you must replace it with a U model plinth This is necessary to avoid the risk of injury caused by protruding metal parts Correct use P Do not use solvents in the dishwasher Danger of explosion P Do not inhale or ingest dishwasher detergent Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose mouth and throat if swallowed or inhibit breathing Consult a doctor immediate ly if detergent has been swallowed or inhaled P Avoid leaving the door open unnecessarily as you could trip over it P Do not sit or lean on the opened door This could cause the dishwasher to tip and be damaged and you could get injured P Only use detergent and rinse aid formulated for domestic dishwashers Do not use washing up liquid P Do not use commercial or industrial detergents as these may cause damage and there is a risk of severe chemical reaction P Do not fill the rinse aid reservoir with powder or liquid detergent This will cause serious damage to the reservoir Warning and Safety instructions P Inadvertently filling the salt reservoir with powder or liquid dishwasher detergen
62. ss any buttons during this time Pressing any button will switch the display back on again A dot in the display next to a selector button indicates that a function can be selected with that button 7 Le The arrows on the right hand side of the display indicate that more options or more text are available which can be displayed by pressing the relevant selector button A dotted line will appear after the last option available OK The OE function is used to confirm a message or setting and also to move to the next menu or to another menu level A tick will appear beside the option which is currently selected The Settings menu is used to alter the dishwasher s electronics to suit different requirements See Settings menu for more details Warning and Safety instructions This appliance conforms to current safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information on its safety use and maintenance Keep these instructions in a safe place and pass them on to any future owner Correct application P This dishwasher is intended exclusively for cleaning domestic crockery and cutlery in a domestic household Using it for purposes other than those for which it was designed as
63. t will damage the water softener Make sure you have bought the correct packet of dishwasher salt before filling the salt reservoir P Please only use special coarse grained dishwasher salt for reactivation as other salts may contain insoluble additives which can impair the functioning of the softener see Filling the salt reservoir gt In an appliance with a cutlery basket depending on model cutlery is cleaned and dried more efficiently if placed in the basket with the handles downwards However to avoid the risk of injury place knives and forks etc with the handles upwards P Plastic items which cannot withstand being washed in hot water such as disposable plastic containers or plastic cutlery and crockery should not be cleaned in the dishwasher The high temperatures in the dishwasher may cause them to melt or lose shape P On models with Delay start make sure that the dispenser is dry before adding detergent Wipe dry if necessary Detergent will clog if poured into a damp dispenser and may not be thoroughly dispersed 12 Accessories P Only use genuine Miele spare parts and accessories with this appliance If spare parts or accessories from other manufacturers are used this will invalidate the guarantee and Miele cannot accept liability Disposal of your old dishwasher P Make the door lock inoperative so that children cannot accidentally shut themselves in Make appropriate arrangemen
64. ts for the disposal of the appliance The manufacturer cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Caring for the environment Disposal of the packing material The packing material protects the dryer from transport damages The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled The packaging consists of the following materials Outer packaging Corrugated cardboard made from up to 100 recyclable material or Polyethylene PE protective wrap Polyproplylene PP strapping Inner packaging Chlorine and fluorine free expanded polystyrene EPS Base lid frame and support battens made from untreated natural wood from renewable forests Polyethylene PE protective wrap Rather than just throwing these materials away please ensure they are offered for recycling Disposal of your old appliance Electrical and electronic machines often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Therefore please do not dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact you dealer for advice Ensure that it presents
65. until the catch engages The door will then close automatically Do not put your hand inside the door as it is closing you may catch aS your fingers Danger of injury At the end of the programme the door will open automatically a little in order to help the drying process This function can be deactivated see Settings menu Drying plus m Pull the handle If the door is opened during operation all functions are automatically interrupted A Keep the area around the door free of obstructions Before using for the first time Welcome screen m Switch the dishwasher on with the On button If the dishwasher is being switched on for the first time the welcome screen will appear Setting the language Clock display 16 The display will then change automatically to the screen for setting the language testina Language y dansk m Select the language you want and confirm this with DK A tick will appear next to the language that has been set The display will then change to the screen for setting the clock display 12 h Clock 24 h Clock Clock display m Select the clock display you require and confirm this with Dk Before using for the first time Setting the time of day The display will then change to the screen for setting the time 00 Flease set the time m Set the hours with and confrim with DK Then set and confirm the minutes These sett
66. usly The appliance is set at the factory for using normal dishwasher detergent m Select the detergent type you want and confirm with OE Settings menu F Drying plus Value displayed At the end ofa programme with a od mmoii of in time display drying phase see Programme chart Germa the door will open automatically a little n scale in order to help the drying process 1 0 2 2 1 2 0 4 4 2 This function can be deactivated if 3 05 5 3 wished 4 0 7 7 4 5 0 9 9 5 select the option you want and 6 14 11 6 confirm with CIC 7 13 13 7 8 1 4 14 8 Drying plus will not operate in the x b 1 pa Marrmal programme 11 20 20 11 12 2 2 22 12 Water hardness 3 2 3 23 3 14 2 5 25 14 Your dishwasher is fitted with a water 15 2 7 27 15 softener sensor which determines the v 2 E E water hardness level of your local water 18 32 32 18 supply automatically 19 3 4 34 19 After your dishwasher has been 20 3 6 36 20 through one programme cycle e g 2 Pre wash you can call up the water 23 41 41 23 hardness level measured by the water 24 4 3 43 24 softener sensor via the Water hardness 25 4 5 45 25 26 47 47 26 ion opts 27 49 49 27 m OF will return you to the Settings 28 5 0 50 28 menu P 29 5 2 52 29 30 5 4 54 30 31 5 6 56 31 32 5 8 58 32 33 5 9 59 33 34 6 1 61 34 35 6 3 63 35 36 6 5 65 36 37 45 6 7 8 1 67 81 45 46 60 8 3 10 8 83 108 60 61 70 11 0 12 6 110 126 70 79 Settings
67. wash additional items of cutlery a small cutlery basket for the lower basket wash a lot of glasses a glassware insert for the lower basket wash large plates 70 an insert for plates up to 38 cm diameter 35 cm diameter Electrical connection A Please follow the installation instructions carefully All electrical work should be carried out only by a suitably qualified and competent person in strict accordance with national and local safety regulations Ensure power is not supplied to the appliance while installation work is being carried out This dishwasher is supplied with a mains cable and moulded plug ready for connection to an a c single phase supply 230 240 V 50 Hz for NZ and Australia via a fused plug and suitable switched socket which is easily accessible after installation m he voltage rated load and fuse rating are given on the data plate located above the door Please ensure that these match the household mains supply For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA m Do not connect via an extension lead ff the connection cable is damaged it must be replaced with a complete connection box and cable by a Miele approved service technician only The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live If the colours o
68. well as any alterations or conversions to the appliance would be unauthorised and could cause harm The manufacturer cannot be held liable for damage resulting from improper or incorrect use of the appliance gt This dishwasher is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they are supervised whilst using it or they have been given instruction concerning its use by a person responsible for their safety Safety with children P This appliance is not a toy To avoid the risk of injury keep children well away and do not allow them to play in or around the dishwasher or to use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen There is a danger that children playing might shut themselves in the dishwasher P Older children may only use the dishwasher when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse P Keep children away from detergents Dishwasher detergents contain irritant and corrosive ingredients which can cause burning in the mouth nose and throat if swallowed or inhibit breathing Keep children away from the dishwasher when the door is open There could still be detergent residues in the cabinet Consult a doctor immediately if your child has

Miele G 2874 SCVi

Contents

Download Pdf Manuals

Related Search

Related Contents