Brickcom OB-100Ap
Contents
1. Brickcom Before You Use This Product In many countries there are laws prohibiting or restricting the use of surveillance devices This Network Camera is a high performance web ready camera which can be part of a flexible surveillance system It is the user s responsibility to ensure that the operation of this camera is legal before installing this unit for its intended use Upon opening the products package verify that all the accessories listed on the Package Contents are included Before installing the Network Camera read the warnings in the Quick Installation Guide to avoid misuse When installing the Network Camera carefully read and follow the instructions in the Installation chapters to avoid damages due to faulty assembly or installation EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equ2. Lu amp Lu D D DS E LE Lu Lr d EXPERT IN WIRELESS IP SURVEILLANCE Brickcom C Wi Fi Antenna Package contents Optional Refer to the installation guide included in the package when installing the 3G antenna a 3G Antenna b Extension Cable d Mount Kit ul Ee La D a D u Lu H 5 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Chapter 2 Outdoor Bullet Network Camera Overview The Brickcom Outdoor Bullet SERIES is an outdoor bullet network camera It adopts a megapixel sensor which allows the camera to deliver extremely clear and detailed images that CCTV cameras cannot offer To optimize use of the megapixel resolution the Outdoor Bullet SERIES uses efficient H 264 MJPEG MPEG 4 codec compression to deliver dual configurable video streams simultaneously at up to 30 fps These features make this series the perfect outdoor camera for neighborhood school campus and parking lot surveillance The Outdoor Bullet SERIES has many user friendly features such as the Smart Focus capability which allows users to configure settings for excellent image quality without difficult procedures Support for Power over Ethernet enables the camera to use the same cable for power and data transmission eliminating the need to install an external power supply Installation for the WOB GOB Series models is not restricted by location or landforms The cameras offer various wireless opt
3. Brickcom Hardware User s Manual Megapixel Day amp Night Outdoor Bullet Network Camera Quality Service Group Outdoor Bullet V2 Series Brickcom Review History 1 Separate User Manual into HW and SW 2 Merge OB 100A V2 series OB 130N series into this User Manual 3 Add OB 500A Series OB 300N Series into the User Manual Product name Release Date Manual Revision Web site Email Network Camera Outdoor Bullet V2 series 2012 05 V3 1 www brickcom com technical brickcom com info brickcom com 2011 Brickcom Corporation All Rights Reserved EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Table of Contents Before You Use This Product ccccccecceeceeecenseeesenecneeeesensenesenscneeeeseneonesensonseeesaneoes 1 Regul tory InIormallODiuuia an e 2 Plaque signal tique du produit final 4 Chapter 1 Package Contents nanne eene nennnernnne mene nenseersnensnnrmenenenenn 6 Chapter 2 Outdoor Bullet Network Camera Overview seen 9 Chapter 3 Device Appearance Description eese erre 10 Ghliapter sett EE eege 14 4 1 Hardware WIS AN AU ON ed nc EYE de din 14 4 2 Camera Connection ccccccceecceeceeeeeeeeneeeeeeneeneeeesoneneesenseneseesenseeesensenesensones 20 4 9 System E E E CN 22 4 4 Software MStallatlOM ae ae ae 23 BO Kee ue 31 EXPERT IN WIRELESS IP SURVEILLANCE
4. SIM Card Installation a Remove the Lens cover from the Bullet Camera b Inset the Micro SD SDHC card and 3G SIM card into their respective slots d Reattach the Lens cover and secure the cover to the top of the camera device using two screws EXPERT IN WIRELESS IP SURVEILLANCE Brickcom B Wall Installation Using the Optional Bracket a Using the Bracket plate as a guide drill three holes into the wall and hammer the supplied plastic anchors into the three holes Use a screwdriver and the supplied screws to secure the plate to the wall b Attach the Bracket Assembly Plate to the bottom of the camera using two screws c 1 Use the two supplied screws to secure the bracket to the side of the camera 2 Push back the spring on the mortise lock and hook the camera and attached bracket onto the groove of the wall mount bracket as shown in the diagram 15 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom d Connect 1 the POE cable 2 DIDO Audio In Out RS485 cable and 3 Antenna cable with the camera Refer to step 3 for more details installation information f Place the wall mount bracket on the plate and attach it using the supplied screws Adjust the angle of the wall mount bracket towards the area to be monitored 16 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom C DIDO Audio In Out RS485 and Antenna Connection a PoE Connection For the Power over Ethernet
5. connection construct the PoE cable using the pin definitions of the RJ45 connector below and refer to step 5 for instructions on how to install the Water Proof Connector Once the PoE cable has been constructed using the waterproof connector pass the RJ 45 cable from the camera through the bracket and connect it to the PoE cable 17 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom b DIDO Audio In Out RS485 Cable Connection For the DIDO Audio In Out and RS485 cable connection construct an Ethernet cable using the pin definitions of the RJ 45 connector below and refer to step 4 for instructions on how to install the Water Proof Connector Once the Ethernet cable has been constructed using the waterproof connector pass the cable through the bracket and connect it to the RJ 45 connector at the bottom of the camera DIDO Diagram AV 4 5V 18 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom c WiFi or 3G Antenna Extension Cable Connection Pass the Antenna extension cable 1 through and bracket and connect it to the Antenna connector 2 at the bottom of the camera d Water Proof Connector Refer to the installation guide included in the package when installing the Water Proof connector i Insert the stripped cable through the sealing nut and the housing Clamp the cable with an RJ45 plug li Push the RJ45 plug into the housing and secure the sealing nut tightly il Attach the gasket to the fr
6. ed 00 26 82 50 Eb df DO 26 82 54 2F A CB 10DAp CE 10DAp CB 10DAp CB 1014p FB 1004p FB 1004p FD 130Ap MD 10DAp vD 100Ap WCB 10DAp WCB 10DAp v3 0 5 13 v3 0 2 3 v3 D 2 5 v3 0 5 12 v3 D 6 7 D For configuring the IP address settings select either Settings remain the same Automatically obtain an IP Address DHCP gt or Set IP Address configuration manually The DHCP setting is recommended settings Settings remain the same Automatically obtain an IP Address DHCP Set IP Address configuration manually 34 EXPERT IN WIRELESS IP SURVEILLANCE If Set IP Address configuration manually is selected the following pages will be displayed Brickcom settings Settings remain the same Automatically obtain an IP Address DHCP Set IP Address configuration manually Brickcom Enter the Static IP Address to configure IP Camera IP Address 169 254 105 144 ek 255 255 0 0 Gateway 169 254 105 134 DNS 1 Gi AE DNS 0 0 0 0 35 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom E If the camera supports the EasyLinkTM function the following page will be displayed Otherwise this page will not be shown If desired click lt Skip gt to skip this setting EasyLink Settings ou can use EasyLink Settings to connect to the IP camera without knowing the IP address EaswvLink Name 002682594233 Le Live View Windows Internet Exp
7. installation an EasyConfig icon was installed on the desktop Double click to open the icon EasyConfig If Custom Setup type was used in the software installation and an EasyConfig icon was not installed on the desktop the program will be installed under C Program Files Brickcom EasyConfig unless the program was saved to a preferred directory A Click Start to continue The program will automatically search for the camera in the intranet A NOTE Check Skip the hardware installation guide to skip checking the hardware connection To check the hardware installation settings do not check the option box Thank wou for choosing Brickcam EasyConfig will help you easily configure your Brickcom IP camera select Language English J Fig well Li 2010 Brickcom Corporation All rights reserved 31 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Connection NETWORK CABLE Brickcom CAMERA ETHERNET PORT Flug ane end of the supplied network cable into your network Switch or router Flug the other end of the supplied network cable into the camera s Ethernet port 32 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Plug the power adapter into the camera s power port Then connect the other end into the power outlet POWER Please check that the LED light is an SOCKET S CAMERA ETHERNET PORT Select either Simple Mode or Professional Mode to obtain the came
8. only by one user at atime If you have purchased multiple licenses for the Software then at any time you may have as many copies of the Software in use as you have licenses If vou obtain the Software together with a hardware product you are allowed to use the Software as a part of the hardware according to this Agreement The Software is in use on a computer when it is loaded into the temporary memory i e RAM or installed into the permanent memory e g hard disk CD ROM or other storage device of that computer In the event BRICKCOM provides you the upgrade for the Software you may use the resulting upgraded Software only in accordance with the terms of this amp areement acceptthe terms ofthe license agreement Print do not accept the terms ofthe license agreement 24 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom D Select either Complete setup or Custom setup to install the system a If COMPLETE SETUP is selected i All program features will be installed into the default directory Check the option Complete and then click lt Next gt i Brickcom Software Kit x Setup Type Select the setup type to install Please select a setup type Complete fs All program features will be installed Requires the most disk space ob L2 Custom zi EC ok users Cancel en ii Click Change to change the appointed folder where install
9. BI Please try again ar click Finish to quit the installation EIE GENE 37 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom c If the connection was successful the user will see the message Congratulations The installation of the camera is complete NN When this window is displayed click lt PC NVR gt to start the PC NVR program lt Live View gt to view the live video from the connected IP Camera or lt X gt in the top right corner of the screen to close the installation window If the user starts the PC NVR program please refer to the PC NVR user manual Once installation is complete the Administrator should proceed to the next section Accessing the Network Camera for necessary changes and configurations 38 EXPERT IN WIRELESS IP SURVEILLANCE
10. Brickcom Corporation All Rights Reserved 23 EXPERT IN WIRELESS IP SURVEILLANCE rickcom B In the Install Shield Wizard dialog box click Next to continue r 4 E ge Ter a 4 Brickcom Software Kit Welcome to the InstallShield Wizard for Brickcom Software Kit The InstallShield Wizard will install Brickcom Software Kit on your computrer Click Next to continue or Cancel to exit the Installation Wizard Irisiall C Read the End User License Agreement and check the option accept the terms of the license agreement Click Next to continue Brickcom Software Kit License Agreement Please read the following license agreement carefully End User License Agreement IMPORTANT READ CAREFULLY This End User License Agreement the 4greement is a legal agreement between you either an individual of an entity and BRICKCOM CORPORATION BRICKCOM regarding the use of the BRICKCOM s software entitled Brickcom Software Kit version 1 5 5 which may include user documentation provided in online or electronic form the Softvvare By clicking the button marked ACCEPT or YES below you agree to be bound by the terms of this Agreement If you do not agree to the terms of this Agreement please do not install or use the Software 1 Grand of License This amp greement permits you to use one copy of the specified version of the Software for internal purpose only on onl one computer and
11. a reglementation d Industrie Canada le present emetteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inferieur approuve pour l emetteur par Industrie Canada Dans le but de reduire les risques de brouillage radioelectrique a l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonnee equivalente p i r e ne depasse pas l intensite necessaire a l etablissement d une communication satisfaisante Le present emetteur radio IC 9219A WMDR129N a ete approuve par Industrie Canada pour fonctionner avec les types d antenne enumeres ci dessous et ayant un gain admissible maximal et l impedance requise pour chaque type d antenne Les types d antenne non inclus dans cette liste ou dont le gain est superieur au gain maximal indique sont strictement interdits pour l exploitation de l emetteur EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Ce dispositif a ete concu pour fonctionner avec une antenne ayant un gain maximal de dB 2 02 Une antenne a gain plus eleve est strictement interdite par les reglements d Industrie Canada L impedance d antenne requise est de 50 ohms Cet appareil est concu uniquement pour les int grateurs OEM dans les conditions suivantes Pour utilisation de dispositif module 1 L antenne doit tre install e de telle sorte qu une distance de 20 cm est respect e entre l antenne et les utilisateurs et 2 Le module me
12. ation and program files will be stored Click Next to continue Brickcom Software Kit CH Choose Destination Location Select folder where setup will install files Eom Install Brickcom Software Kit to CaPragram FilesiBrickcom Cancel 25 EXPERT IN WIRELESS IP SURVEILLANCE rickcom Brickcom Software Kit Setup Type Selectthe setup type that best suits your needs Select to create shortcuts Click lt Next gt to continue The InstallShield Wizard has successfully installed Brickcom Software Kit Click Next to continue iv Create Desktop Shortcut M Create Quick Launch Shortcut D Create StartMenu Shortcut 1115 i I elu iv The installation information will be displayed continue Brickcom Software Kit Please read the following text Current Settings Setup Type Complete Select Features EasyConfig PC NYR Standard Choose Destination Location EasyConfig C Program Files Brickcom EasyConfig PC NVR Standard C Program Files BrickcomiPC NVR StandardiEXE Creating shortcuts EasyConfig Create Desktop Shortcut Create Quick Launch Shortcut Create StartMenu Shortcut PC NVR Standard 26 Click Next to EXPERT IN WIRELESS IP SURVEILLANCE Brickcom v To launch EasyConfig or PC NVR Standard select the application and click lt Finish gt When launching the PC NVR program please refer to the PC NVR user manual Brickcom Software Kit Instal
13. e factory to match the intended destination The firmware setting is not accessible by the end user EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Industry Canada statement Ce dispositif est conforme la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage recu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable NOTE IMPORTANTE Pour l utilisation de dispositifs mobiles D claration d exposition aux radiations Cet quipement est conforme aux limites d exposition aux rayonnements IC tablies pour un environnement non contr l Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps Avertissement Le dispositif fonctionnant dans la bande 5150 5250 MHz est r serv uniquement pour une utilisation l int rieur afin de r duire les risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux Les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux c d qu ils ont la priorit pour les bandes 5250 5350 MHz et 5650 5850 MHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL Conformement a l
14. es an extension I O terminal block which is used to connect the camera with external input output devices The pin definitions are listed as below lt DI DO Diagram gt PIN 1 Poner tu AM 4 5V EXPERT IN WIRELESS IP SURVEILLANCE Brickcom lt Hardware Reset gt Reset Buttone The Reset Button can be used to reboot the camera or restore it to factory default settings If the camera experiences a problem rebooting the camera may correct the problem If the problem remains please restore the camera to factory default settings and reinstall the software To Reboot Press and hold the Reset Button for one second using a paper clip or thin object Wait for the camera to reboot To Restore Press and hold the Reset Button for ten seconds until the LED light turns off When successful restored the LED will be blue during normal operation A NOTE By restoring the camera all settings will be restored to the factory default settings Micro SD SDHC Card Capacit The network camera is compatible with Micro SD SDHC Maximum 32GB cards These are optional features Please refer to the Product List for the full list of optional features that are available for this product 13 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Chapter 4 Installation 4 1 Hardware Installation AN WARNING Do not mount the camera on a soft material The camera may fall and be damaged A Micro SD SDHC Card and 3G
15. ions that make connecting to networks easier by adopting the technology of IEEE 802 11 a b g n and 3G SIM module The wireless Bullet Cameras can be set within any wireless or 3G signal coverage areas Users do not have to worry about the data connection failing because each camera is equipped with a SD SDHC memory card slot for local storage With an IP67 certified outdoor enclosure the Outdoor Bullet SERIES is not only weather proof but also dust and rust resistant By utilizing a built in industrial fan and heater it can perform well in extreme environments 3G Phone g ed f 3G N t k NB PC with gt web Browser d o NB PC with web Browser MYR ef j Ze Internet Weather Proof CH sl gt Gs AP Router Pd N G er Residence e A Y Weather Proof Building B 4 ZE S Scenic Spot Traffic Historic spot EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Chapter 3 Device Appearance Description lt Front Panel gt IF LED Light Sensor lt Rear Panel gt shielding Cover Ventilation Hole lt Top gt Screw Holes 10 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom lt Bottom gt Screw Holes RI45 Connector 1 RI45 Connector Antenna Connector lt Side gt Micro SD SDHC Card Slot Reset Buttone 11 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom lt Extension I O Terminal Block gt The Network Camera provid
16. ipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation AN IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter The availability of some specific channels and or operational frequency bands are country dependent and are firmware programmed at th
17. lation Complete Thank you for choosing Brickcom iv Co you want to launch the application now EasyConfig PC NVR Standard Finish b If CUSTOM SETUP is selected i This option is recommended for advanced users t can be used to install the system to a preferred directory or to select specific program feature s ii Check the option Custom and then click lt Next gt Brickcom Software Kit x Setup Type Selectthe setup type to install Please select a setup type Complete ia All program features will be installed Requires the most disk space ofi W Lu le Custom PLE Select which program features you want installed Recommended for advanced Kaf users Cancel 27 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom ii Select the features to install Click Next to continue Brickcom Software Kit KH Select Features Selectthe features setup will install z fig will help users easily configure the Brickcom IP camera Space Required on C 50533 K Space Available on C iv Click Change to change the appointed folder where installation and program files will be stored Click Next to continue Brickcom Software Kit Choose Destination Location Select folder where setup will install files EE oe Install Brickcom Software Kit to CaProgram FilesiBrickcom Cancel 28 EXPERT IN WIRELESS IP SURVEILLANCE rickcom v Select program
18. lorer E zl Ed E http il002682592c33 mybrickcom com EasyLinkTM is a unique Brickcom function which allows users to assign a unique EasyLink name to their network camera s IP address There is no need to configure the router to open up ports or remember hard to memorize IP addresses Users can log onto uniqueEasyLinkname mybrickcom com to view the camera s web GUI and live view a Enter a unique EasyLink name whose length must be between 5 32 characters b When finished click the arrow button to continue 36 EXPERT IN WIRELESS IP SURVEILLANCE F When the IP address settings have been configured the screen will either display a successful or failed connection message If the connection failed either try again or quit the installation a If DHCP IP address settings was selected the failure page will be displayed as below Brickcom Sorry cannot connect Water a IP Camera VvCb 1004p has no response please check 1 If your router supports a DHCP server 2 Set computer IP address to 192 168 1 100 and subnet mask to 255 255 255 0 if your computer connects to the IP camera directly Please try again or click Finish to quit the installation GER GC b If Static IP address settings was selected the failure page will be displayed as below WT Brickcom Sorry cannot connect 0 0 IP CameraivvcBg 100 amp p9 has no response the following settings are recommended Gateway IBI RE I
19. ont of the housing iv Connect the Ethernet cable to the RJ45 cable v Secure the connectors tightly Q x G be gt EXPERT IN WIRELESS IP SURVEILLANCE Brickcom 4 2 Camera Connection The Outdoor Bullet Series is PoE compliant so there are two options for connecting the camera to a power and Ethernet source The camera can either be connected to a PoE enabled switch or a non PoE switch a If using a PoE enabled switch i Use a single Ethernet cable to connect the camera to the PoE enabled switch b If using a non PoE switch i Use a standard RJ 45 cable to connect the camera to a PoE Injector li Use a standard RJ 45 cable to connect the PoE Injector to the non PoE switch ii Use a standard power cable to connect the PoE Injector to a power outlet 20 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom c If using a PoE injector as power input For GOB WOB Series i Use a standard RJ 45 cable to connect the camera to a PoE Injector li Use a standard power cable to connect the PoE Injector to a power outlet d If using the DC12V for the power Supply The RJ45 cable will be data transmission This only apply in OB 500A Series OB 300N Series 21 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom 4 3 System Requirements Operating System Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 Computer IBM PC AT Compatible CPU Pentium 3GHz o
20. r faster Memory 1024 MB or more Monitor 1024 x 768 pixels or more 24 bit True color or better Network Interface 10 100Mbps Network interface card must be installed Web Browser Microsoft Internet Explorer 6 0 SP2 or higher Adobe Reader Adobe Reader 8 0 or higher Audio The audio function will not work if a sound card is not installed in the PC Audio may be interrupted depending on network traffic 22 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom 4 4 Software Installation In this manual User refers to whoever has access to the Network Camera and Administrator refers to the person who can configure the camera and grant user access to the camera After checking the hardware connection run the Installation Wizard program included on the products CDROM to automatically search the intranet for the camera There may be many cameras on the local network Differentiate the cameras using the serial number which is printed on the labels on the carton and the bottom of the camera A Insert the Installation CD into the CD ROM driver Run Auto Run Tool directly from the CD ROM to start the installation When installing the Brickcom software kit for the first time select a desired language for the interface The available languages are listed in the scroll box Click lt Install gt and follow the steps to install the EasyConfig wizard on the desired computer English EL TE cw ne de on L 2010
21. ra s IP settings If Simple Mode is selected EasyConfig will set up the connection automatically If Professional Mode is selected the user will need to configure the IP settings manually Brickcom If simple mode is selected the easy configuration program will set up the connection automatically If professional mode is selected the user will need to configure the IP manually The DHCP setting is recommended If user wants to set the IP address manually please refer ta the product user manual Simple Mode Professional Mode 33 EXPERT IN WIRELESS IP SURVEILLANCE C There may be many cameras in the local network Differentiate the cameras using their UPnP name Double click on the camera from the survey list to connect p I 1 Brickcom Please double click the camera you wantto Connect trom the list 1 2 3 4 5 6 7 8 CB 10DAp 4b11 CB 1004p 4c1F CB 1 lAp 4c21 CB 1 0Ap 89c6 CB 1014p 0001 FB 1004p da99 FB 1004p db00 FD 1308p 69F7 MD 1004p 6400 DO 1004p 30ed Wil B 100 4p 2bdF WCB 1004p 2F93 192 168 1 18 169 254 77 17 169 254 31 48 192 168 1 23 169 254 77 17 192 1568 1 245 169 254 147 48 192 166 1 245 169 254 77 1 132 168 1 245 169 254 12 37 158 254 77 17 MAC Address O0 26 87 05 db 11 D0 26 82 93 4c 1F 00 26 82 93 4c 21 0 26 82 5d 88 c6 00 26 BE cd Fb be 00 26 62 1b da 98 00 26 82 1b dh 00 OD EE BE ct 69 FF OO z6 82 64 864 00 0 26 82 ac 30
22. re tiquet dans un endroit visible avec l inscription suivante Contient des IC 9219A WMDR 129N EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Manuel d information l utilisateur final L int grateur OEM doit tre conscient de ne pas fournir des informations l utilisateur final quant la facon d installer ou de supprimer ce module RF dans le manuel de l utilisateur du produit final qui int gre ce module Le manuel de l utilisateur final doit inclure toutes les informations r glementaires requises et avertissements comme indiqu dans ce manuel EXPERT IN WIRELESS IP SURVEILLANCE Brickcom Chapter 1 Package Contents Please check to make sure the product package contains all the accessories listed below A Camera Package Contents a Network Camera b Shielding Cover Outdoor Bullet V2 Series C d Product CD e Warranty Card Easy Installation f 2 Water Proof Connectors Guide paese Warranty Card pe g Dry Bag h High Power POE Optional i Bracket Optional j Bracket Assembly Plate Optional k Wi Fi Dual Band Antenna package l Optional EXPERT IN WIRELESS IP SURVEILLANCE Brickcom m Power adapter B Wi Fi Antenna Package contents Optional Refer to the installation guide included in the package when installing the Wi Fi antenna a Wi Fi Dual Band Antenna b Extension Cable c Surge Arrestor Kit d Mount Kit
23. s to create shortcuts Click lt Next gt to continue Brickcom Software Kit Setup Type Selectthe setup type that best suits your needs The InstallShield Wizard has successfully installed Brickcom Software Kit Click Next to continue iv Create Desktop Shortcut M Create Quick Launch Shortcut D Create StartMenu Shortcut 1115 i I elu vi The installation information will be displayed continue Brickcom Software Kit Please read the following text Current Settings Setup Type Custom Select Features EasyConfig PC NVR Standard Choose Destination Location EasyConfig C Program Files Brickcom EasyConfig PC NVR Standard C Program Files BrickcomiPC NVR StandardiEXE Creating shortcuts EasyConfig Create Desktop Shortcut Create Quick Launch Shortcut Create StartMenu Shortcut PC NVR Standard 29 Click Next to EXPERT IN WIRELESS IP SURVEILLANCE Brickcom E To launch EasyConfig or PC NVR Standard select the application and click lt Finish gt When launching the PC NVR program please refer to the PC NVR user manual Brickcom Software Kit Installation Complete Thank you for choosing Brickcom iv Do you want to launch the application now EasyConfig PC NVR Standard 30 EXPERT IN WIRELESS IP SURVEILLANCE Brickcom 4 4 1 EasyConfig To launch EasyConfig select EasyConfig from the start menu If Complete setup type was used in the software
24. tteur peut ne pas tre co mplant avec un autre metteur ou antenne 3 Pour tous les produits vendus au Canada OEM doit limiter les fr quences de fonctionnement CH1 CH 11 pour bandes de fr quences 24G gr ce aux outils de microprogrammation fournis OEM ne doit pas fournir d outil ou d informations l utilisateur final en ce qui concerne le changement de r glementation de domaine Tant que les 3 conditions ci dessus sont remplies des essais suppl mentaires sur l metteur ne seront pas n cessaires Toutefois l int grateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit suppl mentaires requis pour ce module install NOTE IMPORTANTE Dans le cas o ces conditions ne peuvent tre satisfaites par exemple pour certaines configurations d ordinateur portable ou de certaines co localisation avec un autre metteur l autorisation du Canada n est plus consid r comme valide et l ID IC ne peut pas tre utilis sur le produit final Dans ces circonstances l int grateur OEM sera charg de r valuer le produit final y compris l metteur et l obtention d une autorisation distincte au Canada Plaque signal tique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l antenne peut tre install e de telle sorte qu une distance de 20cm peut tre maintenue entre l antenne et les utilisateurs Le produit final doit t
Download Pdf Manuals
Related Search