Thorens TD 190-2
Contents
1. recess of the gauge Fig 9 Adjust the cartridge in the head shell until the correct positions are achieved Lastly tighten the mounting screws put the head shell with cartridge back on the tone arm and tighten the collar lock 9 ATTENTION During these mounting and adjustment procedures you must be very careful not to damage the delicate stylus and cantilever by uncontrolled and brisk movements Replacing the stylus Any stylus is subject to wear even under normal playing conditions Therefore it is highly recommended to have the cartridge respectively its stylus inspected after about 500 hours of playing This is because a worn or damaged stylus will eventually damage your precious vinyl records In order to playback vintage shellac records 78 s with optimal results the original stylus should be exchanged with a suitable special stylus for shellacs Please consult your THORENS dealer for further information and details TD 190_E Fig 7 R red RG green L white LG blue Fig 9 right channel right channel ground left channel left channel ground Selecting Speed With the knob on the left the speed can be set at 33 45 und 78rpm Fig 10 Selecting record diameter With the button 6 on the right near the tone arm the diameter of the records can be pre set whereby 17 cm is used for Single and 30 cm for Long Play LP vinyl records This function is necessary only when the reco2. the tone arm can be precisely balanced in order to make it hover freely above the platter Move the tone arm back to its rest You can now adjust the tracking force 1 and the anti skating force 2 Adjust to 1 5 mN Milli Newton for the factory installed pick up cartridge OMB 10 As for the required anti skating force refer to the table below Scale Tracking force 1 Anti skating force 2 1 10 mN 1 1 25 12 5 mN 1 25 1 5 15 mN 1 5 2 20 mN 2 2 5 25 mN 2 5 3 30 mN 3 TD 190_E Fig 5 Mounting or exchanging a pick up cartridge Instead of the factory supplied pick up cartridge any other cartridge with standard half inch mounting holes and a weight between 3 and 10 grams can be installed To do this loosen the collar lock 9 and pull off the head shell Fig 7 Unscrew the cartridge and carefully remove the coloured signal leads from the cartridge pins with a pair of tweezers Screw the new cartridge onto the head shell but do not tighten Attach the leads to the pins while observing the correct coding Please note The example shown in Fig 8 is appli cable only for the pick up cartridge OMB 10 For the precise adjustment of the so called stylus overhang push the head shell with cartridge into the Supplied mounting gauge The adjustment is correct if the stylus is flush with the V shaped recess in the gauge as viewed from above When viewed from the side the stylus should be seen within the rectangular
3. the warranty period please inform your THORENS dealer or general representative and describe the malfunction that has occurred If the malfunction cannot be remedied on site by sending you the respective user serviceable spare part you are kindly requested to send the unit in its original shipping box to the THORENS representative in your country If the original shipping box is no longer in your possession your THORENS representative will be in the position to supply a new one for a small charge Shipping costs to THORENS or to an authorized service centre must be prepaid because otherwise the parcel will be rejected upon arrival After repair or service the unit will be returned to you free of charge Whenever you ship this turntable kindly use the screws for the security during transportation Any damage or malfunction caused by failure to observe the instructions contained in this manual as well as damages occurred in transport or shipping are not covered by this warranty This warranty only covers the turntable and motor including power supply and mains transformer The tone arm and pick up cartridge are covered by the warranty of the respective manufacturer thereof In the event that you have further queries or need assistance please do not hesitate to contact your authorised THORENS service WARNING To prevent fire or shock hazard do not expose this product rain or moisture TD 190_E 3 Technical Data Measured values typica
4. THORENS INSTRUCTION MANUAL TD 190 TD 190 1 Contents Page Thorens Factory Warranty 2 Technical Specification 3 Unpacking and Assembly 4 Electrical Connections and Installation 4 Tonearm and Pickup Cartridge 5 Vertical alignment of cartridge 6 Operation of the TD 190 7 TD 190_E Dear THORENS customer Thank you very much for your confidence in our product the record player TD 190 With the purchase of this device you have acquired a precision instrument for the purpose of playing back analogue records This appliance however requires your attention with respect to set up placement and handling in order to achieve a flawless operation The TD 190 has been designed and assembled completely in Germany which will guarantee you the highest quality to be maintained for years to come Understandably you want to listen to your beloved records right away but we strongly advise that you read these instructions attentively before proceeding with the setup simply to ensure long lasting listening pleasure We have spared no efforts to pack all necessary information and comprehensive guidance into this manual yet in the event that you have any further queries regarding your new record player please do not hesitate to ask your THORENS dealer for further assistance Sincerely yours THORENS TEAM WARRANTY Legal warranty directives and regulations are to be applied here In case a failure or malfunction occurs in your record player during
5. at is coming from the mains transformer unit is to be inserted into jack 17 Fig 4 at the rear side of the record player The stereo signal leads have two phono plugs which are also known as Cinch or RCA plugs They are marked with either the letter L for the left channel or R for the right channel If these letters are missing then most likely the right channel is Fig 4 marked red perhaps by featuring a red plug at both ends and the left channel is marked white or black accordingly The RCA plugs are inserted into the phono input jacks of an amplifier or receiver The separate single litz wire is making a connection to ground and is to be fastened underneath the ground screw of the amplifier or receiver IMPORTANT ALWAYS KEEP THE SHIPPING CARTON IN A DRY PLACE FOR THE EVENT THAT THE RECORD PLAYER HAS TO BE PACKED AGAIN FOR TRANSPORTATION IN THIS CASE IT IS IMPORTANT TO DETACH THE PLATTER AND PUT IT ON THE BOTTOM OF THE SHIPPINGBOX JUST AS IT WAS ORIGINALLY DELIVERED TO YOU TD 190_E 5 Adjusting tone arm and pick up cartridge Turn the tracking force adjuster 1 to 0 and the anti skating knob 2 counter clockwise until it stops Fig 6 Screw the tonearm counter weight 3 onto the rear tonearm tube Fig 5 Unlock the tone arm 4 and move it a bit towards the centre of the platter Bring the lift lever 5 into position DOWN while holding back the tone arm Fig 6 By turning the counter weight 3
6. l values Belt drive electronic controlled DC motor CN 0 mm Signal to noise ratio DIN 45 500 Rumble unweighted signal to noise ratio 46 dB Rumble weightes signal to noise ratio 72 dB Cartridge HiFi DIN 45 500 rot R right channel Ortofon grun RG right channel ground OMB 10 blau GL left channel ground wei L left channel Diamant stylus Nadel 10 elliptical 18 x 8 um Diamant stylus for 78 U min Nadel 78 conical 65 um Frequency range 10 Hz 22000 Hz Total capacitance Tonearm leads and audio cables ca 160 pF Dimensions W x H x D mm 440 x 119 x 360 TD 190_E 4 Unpacking and set up Take the record player and all accessories out of the carton Remove the two transportation locks Fig 1 by applying lateral pressure The locks are located underneath the platter at the front left and at the rear right Put the platter onto the sub platter and press down the two safety springs until they set into the groove of the platter spindle Fig 2 Insert each hinge into the respective recess Fig 3 Hold the dust cover parallel to the hinges opening angle approximately 60 insert and push as far as it will go Being in this position the dust cover may be removed at any time Fig 1 Fig 2 Fig 3 Electrical connections By choosing the appropriate THORENS mains transformer this record player can be operated from nearly all existing public mains supplies The low voltage plug on the cable th
7. rd player is operated in its automatic mode Fig 10 Automatic start Remove the transparent stylus guard by carefully pulling it towards you The lift lever 5 must be in position UP Move the knob 7 into position Start and the tone arm will be automatically lowered onto the record Fig 11 Manual start and tone arm lift Bring the lift lever 5 into position UP Unlock the tone arm from its rest and move it above the lead in groove of the record The motor and platter will now start turning By lowering the lift lever 5 the tone arm gently declines thus being very kind to your precious records With the help of the lift lever the tone arm may be moved up and down again anywhere across the record while the platter keeps turning Fig 11 Stop After reaching the lead out groove the tone arm will be automatically lifted up and returned to its rest The motor is switched off You can also switch off the record player by either moving knob 7 into position Stop or by raising lift lever 5 into Fig 11 position UP and returning the tone arm manually to its rest TD 190_E 8 THORENS Thorens Export Company Lid Im H bel 1 CH 4304 Giebenach Basel Switzerland Tel 41 0 61 8 13 03 37 Fax Tel 41 0 61 8 13 03 39 Internet http www thorens ch Email info thorens ch TD 190_E
Download Pdf Manuals
Related Search