Home

Chief NAV1 projector accessory

1. INSPECT NAV 2 PARTS BEFORE ASSEMBLY Table 4 NAV 2 Parts 1 Open the shipping container and remove the NAV 2 from the container 2 Carefully inspect the NAV 2 for shipping damage If any damage is apparent call your cartier claims agent and do not continue with the assembly Remove and Inspect the NAV 2 procedure until the carrier has reviewed the damage TALOK ARRIGO NOTE Read all assembly instructions before knoss C s S starting assembly 60 pee 10 24 x 1 1 4 PHILLIPS HEAD MACHINE 3 Carefully inspect all components for damage SCREW BZ See Table 4 Figure 11 and Figure 12 10 24 x 5 8 PHILLIPS HEAD MACHINE SCREW BZ NOT SHOWN 08 32 x 1 1 4 SOCKET HEAD CAP SCREW 5 9 32 HEX KEY NOT SHOWN 1 These 2 screws supplied with lens Figure 11 NAV 2 Lens Support Figure 12 NAV 2 Lens Support Top View Instruction Instructions NAV 2 INSTALLATION PROCEDURES Except for the Installing and Adjusting Lens procedure provided in this section the NAV 1 and NAV 2 installation procedures are the same Table 5 provides a cross reference list of the NAV 1 installation procedures Refer to the corresponding NAV 1 procedure to install the NAV 2 Table 5 Cross Reference List Ref NAV 1 Installation Procedures Removing Projector from Ceiling Mount Attaching NAV 1 to RPA Adjusting NAV 1 to Projector Lens Installing and Adjusting Lens Install and adjust the NAV 2 conversion lens as
2. INSTALLATION INSTRUCTIONS NAV 1 Lens Support The NAV 1 Lens Support is compatible with any RPA projector mount The NAV 1 readily adapts to the following ScreenStar Conversion Lens from Navitar SSW08 and SST120 NAV 1 LENS SUPPORT NAV 2 NAV 2 Lens Support The NAV 2 Lens Support is compatible with any RPA projector mount The NAV 2 will readily adapt to a conversion lens that is not screw mounted to the lens support The NAV 2 Lens Support can also be used on projectors that have an inset lens NAV 2 LENS SUPPORT BEFORE YOU BEGIN CAUTION To prevent damage to the mount which could affect or void the Factory warranty thoroughly study all instructions and illustrations before you begin to install the mount brackets Pay particular atten tion to the Important Warnings and Cautions on Page 2 If you have any questions about this installation contact Chief Manufacturing at 1 800 582 6480 or 952 582 6480 TA CHIEF MANUFACTURING INC 8802 000157 Rev C 19 C H l F F 1 800 582 6480 952 894 6280 FAX 952 894 6918 2007 Chief Manufacturing ideas Supporting Ideas 8401 EAGLE CREEK PARKWAY SUITE 700 www chiefmfg com 04 07 SAVAGE MINNESOTA 55378 USA Instruction Instructions NAV 1 A IMPORTANT WARNINGS and CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destructio
3. follows NOTE Retain the two screws not shown that are provided to attach the front plate to the main plate 40 1 Using the 9 32 hex wrench 130 and five socket head cap screws 120 assemble the outer ring support 100 and inner ring support 110 with the lens not shown as shown in Figure 13 Tighten the Screws 100 2 Using two hex screws attach outer ring support 100 behind the front plate 40 on the NAV 2 Loosen the knob 60 on the NAV 2 Extend the front plate 40 down all the way and finger tighten the knob See Figure 14 3 With an assistant install your projector back on the ceiling mount at this time Secure all thumbnuts and audio video cables Do not restore power to the projector at this time See Figure 15 NOTE Refer to Adjusting NAV 1 to Projector Lens to make the final adjustments 4 Adjust the conversion lens and height of front plate 40 as needed Tighten the knob 60 on the NAV 2 See Figure 15 NAV 2 Retain 2 Hex Screws es al 13 depy ajbuy epi X80 Conversion Lens xN k Figure 14 Leave Front Plate in Down Position Figure 15 Adjust Lens
4. eseeeeeeeeeees 7 Height AGjUStMEN cccececeeeeeeeeeeeseeeeeeteees 7 Adjustment Notes cc cccccseeeeseeeeseeesseeesaaees 7 Table 1 Installation Reference Chart INSPECT NAV 2 PARTS BEFORE ASSEMBLY 8 Ref Remove and Inspect the NAV 2 cscccseeeeeeees 8 maine Pages NAV 2 INSTALLATION PROCEDURES 0 0 0 0 9 Installing and Adjusting Lens cccseeeeeseeeeees 9 Instruction Instructions NAV 1 INSPECT NAV 1 PARTS BEFORE ASSEMBLY Table 2 NAV 1 Parts 1 Open the shipping container and remove the NAV 1 from the container 2 Carefully inspect the NAV 1 for shipping damage If any damage is apparent call your carrier claims agent and do not continue with the assembly procedure until the carrier has reviewed the damage AA CARRIAGE BOLT NOTE Read all assembly instructions before starting assembly 60 KNOB 1 10 24 x 1 1 4 PHILLIPS HEAD MACHINE 3 Carefully inspect all components for damage See SCREW BZ Table 2 Figure 1 and Figure 2 10 24 x 5 8 PHILLIPS HEAD MACHINE 4 SCREW BZ NOT SHOWN 90 10 SAE FLAT WASHER BZ Remove and Inspect the NAV 1 Figure 1 NAV 1 Lens Support Figure 2 NAV 1 Lens Support Top View Instruction Instructions NAV 1 INSTALLATION PROCEDURES NAV 1 Removing Projector from Ceiling Mount To install the NAV 1 Lens Support hereinafter called the NAV 1 perform the following procedures The projector m
5. holes on the RPA On the RPA remove two screws from the first set of slotted holes on the RPA See Figure 4 NOTE 2 screw pair on opposite side of RPA not shown RPA Remove 7 F screw pair closest to projector Figure 4 Remove front screw pair from RPA Remove the two center screws from the RPA On the NAV 1 loosen the two screws on each side to allow the bracket to extend backward and forward Slide the NAV 1 over the RPA projector mount as shown in Figure 5 Align the slotted holes on the NAV 1 with the slotted holes on the RPA For reference see step 1 four 5 8 screws 80 and four 10 washers 90 NOTE Leave the four screws 80 loose These screws will be adjusted and tightened later Attach the NAV 1 to the RPA by installing four screws 80 and washers 90 into the threaded holes on the RPA Figure 5 RPA NAV 1 Install 80 and 90 NOTE 2 screw pair on opposite side of RPA not shown Figure 5 Attach NAV 1 to RPA Find two 1 1 4 Phillips screws 70 in the parts bag NOTE Stop threading each screw 70 when the end protrudes through the bracket hole approximately 1 4 as shown in Figure 6 Install two screws 70 in the threaded tabs on the NAV 1 See Figure 6 Figure 6 Install Angle Adjustment screws Instruction Instructions Installing and Adjusting Lens Install and adjust the NAV 1 lens as follows 1 Attach conversion lens plate behind the fro
6. n of equipment if you do not follow the corresponding instructions e WARNING Improper installation can result in serious personal injury Make sure that the mounting surface can support a redundant weight factor five times the total weight of the equipment If not reinforce the structure before installing the applicable lens support on the projector e WARNING Be aware of the potential for personal injury or damage to the unit if it is not adequately mounted e CAUTION Inspect the unit for shipping damage CONTENTS TOOLS REQUIRED FOR TOOLS REQUIRED FOR INSTALLATION 2 INSTALLATION REFERENCE CHART sciatic nieces 2 e Phillips screwdriver INSPECT NAV 1 PARTS BEFORE ASSEMBLY 3 Remove and Inspect the NAV 1 cccseeeeeeeeees 3 e 9 64 Allen wrench or Hex wrench NAV 1 INSTALLATION PROCEDUREG 4 NOTE Other tools may be required depending on the Removing Projector from Ceiling Mount 4 method of installation Attaching NAV 1 to RPA cic avcterec tt ee eeecereeeses 5 Installing and Adjusting Lens ccccseeeseeeeeees 6 REFERENCE CHART Adjusting NAV 1 to Projector Lens ccceee 7 o di ee Eng ee ce 7 Table 1 provides a reference chart to help you quickly JUSMENE eee eeeeeseeeseseeeseseseseseeeeeeeeieees find the installation instructions you need Extension AGjUStMent cccceeeseeeeeeeeeeseeeeeees 7 Lateral Shift AdjuStMent ccccsec
7. nt lens Be Tol ele a Celie nod Adjustment plate a Loosen the knob 60 and slide the NAV 1 lens up or down Refer to Figure 10 and adjust the NAV 1 lens to the RPA b Tighten the knob 60 projector lens as follows Adjustment Notes Pitch Adjustment NOTE Except for fine tuning the NAV 1 is adjusted 1 To adjust lens pitch adjust the two angle screws to aiter completing the adjustment process raise or lower the lens This adjustment aligns the However after restoring power to the projector conversion lens with the projector lens you may want to repeat a particular adjustment 2 To adjust lens extension raise or lower the lens do the following a Loosen four screws 30 and washers 90 on NOTE the side of the front adjustable plate 20 procedure in order to make minor changes Extension Adjustment NOTE Depending on your projector model it may be necessary to adjust the lens at a slight angle to the projector lens which helps to correct keystone If you have difficulty with the lens alignment contact Navitar Inc Call Navitar s Customer b Slide the front adjustable plate 20 back so the Service Department at 1 800 828 6778 lens is approximately 1 8 to 1 4 from the projector lens c Tighten the four screws 30 and washers 90 Pitch Adjustment Extension Adjustment Lateral Shift Adjustment Height Adjustment Figure 10 Adjust NAV 1 Lens Instruction Instructions NAV 2
8. nt plate 40 on the NAV 1 Use the two screws and hex wrench that are provided with the conversion lens See Figure 7 Hex Conversion Lens Plate Screws Plate provided with lens not NAV 1 Supplied with two hex screws Figure 7 Attach Conversion Lens to Adjustable Plate 2 Loosen the knob 60 on the NAV 1 Extend the front plate 40 down all the way and finger tighten the knob See Figure 8 Figure 8 Leave Front Plate in Down Position NAV 1 With an assistant install your projector back on the ceiling mount at this time Secure all thumbnuts and audio video cables Do not restore power to the projector at this time See Figure 9 Install the conversion lens at this time Screw the lens into the lens plate that is attached to the front plate 40 See Figure 9 40 Conversion Lens ao Figure 9 Install Conversion Lens Instruction Instructions NAV 1 Adjusting NAV 1 to Projector Lens The NAV 1 lens support can be adjusted to accommodate different projector models and lens Lateral Shift Adjustment placement See Table 3 3 To adjust lateral shift do the following Table 3 NAV 1 Specification Chart a Loosen the knob 60 and slide the lens left or right to the center of the projector lens Pitch 20 down and 10 up b Tighten the knob 60 Extension 3 inches from projector mount Lateral Shift 6 1 4 inches Height Adjustment Height 3 1 5 inches up and down on fro
9. ust be removed from the mount before e Removing Projector from Ceiling Mount e Attaching NAV 1 to RPA e Installing and Adjusting Lens e Adjusting NAV 1 to Projector Lens procedure 1 Power off the projector Thumbscrews 5 3 to 6 Places ht om the RPA ceiling mount 6 Remove the projector Completely Installed NAV 1 EXAMPLE ne e A T S PC CARD E fee R AUDIOIN L VIDEOIN _ S VIDEO IN RGB OUT 0 00 Ib oap a e Disconnect AC D m __ NEC a power cord to 7 ae 3 projector Figure 3 Video Projector Typical installing this accessory With an assistant remove projector from RPA ceiling mount as follows NOTE If your projector is not installed on the RPA ceiling mount proceed to the next 2 Disconnect the power cord that supplies electric RPA power to the projector Ceiling 3 Disconnect the audio video cables from the A Mount projector 4 Loosen the thumbscrews securing the projector to Carefully slide the projector forward until the projector releases from the RPA ceiling mount Disconnect audio video cables from projector Instruction Instructions NAV 1 Attaching NAV 1 to RPA Attach the NAV 1 to the RPA projector mount as follows 6 Locate the parts bag supplied with the NAV 1 Find NOTE The four screws and washers removed from the RPA are located closest to the projector lens Do not remove the screws and washers from the second set of slotted

Chief NAV1 projector accessory

Contents

Download Pdf Manuals

Related Search

Related Contents