Gefen 8x8 DVI Dual Link Matrix
Contents
1. Download DID Cony Emo EINEN Status Lock OFF input EDID Source Name input Dates GEFEN_XPTOL EDID Lock State Update EDID Lock State Update EDID Lock State Secures the Local EDID and disables the automatic loading of the downstream EDID after the Matrix is powered on Select the radio button next to the Off or On option then click the Update EDID Lock State button to apply the change The EDID Lock State has no effect when the Dynamic EDID function is activated Auto Refresh Refresh Check this box to Click to refresh automatically update the the EDID Lock screen every 10 seconds Status screen 61 WEB INTERFACE Masking Matrix Mask Status Change Displays the current masking status for each output 8x8 DL DVI Manager view mateix status manage coi EEE 17 conrcuranion nackupmestore power MANAGEMENT Qutput Input Status i Output 1 Mas Output 2 Output 3 Mask Output 4 Mask Output 5 Mask A GM T new A Oups meus Acive PR Rakesh Auto R Si Changes A m EEEEE 8 Output 7 Input 7 Auto Refresh Refresh Click to refresh the Mask save Changes Status screen Save Changes LLL Click to save the masking change Auto Refresh Check this box to automatically update the screen every 10 seconds Mask Click the Mask button to mask the selected output If th2. Input Input Name 1 inputi Save Input Name Save Input Name Select the DVI input to rename from the pull down list Type the name of the input in the Input Name field Click the Save Input Name button to save changes See page 46 for naming restrictions Save Output Name Select the DVI output to rename from the pull down list Type the name of the output in the Output Name field Click the Save Output Name button to save changes See page 47 for naming restrictions 55 WEB INTERFACE Manage EDID Set Input to Default EDID EDID Status Displays the current EDID status for each input on the matrix and indicates the current Lock State 8x8 DL DVI Manager view marex status RII wasiinc iP courisuranon nackupmestore POWER MANAGEMENT upload eto Download ELD copy Eon EDI Lock State Select Input s to Set to Default Set Inputto Default EDID B Upload EDID EDID Status Lock State OFF mp2 Defaut GEFENOPL DL Auto Refresh Check this box to enable Auto Refresh Auto Refresh will automatically update the screen every 10 seconds Refresh Click to refresh the Matrix Status screen 56 WEB INTERFACE Set Input to Default EDID Press this button from the Manage EDID screen to access this menu system Select Input s to Set to Default Input 1 Input 2 Input 3 Input 6
3. set_telnet username andrew Telnet login updated to andrew sgateway Command The Zsgateway sets the IP gateway router address Dot decimal notation must be used when specifying the IP address The default address is 192 168 1 254 Syntax sgateway paraml Parameters param1 IP gateway Notes The default gateway IP address is 192 168 1 254 The matrix must be rebooted after executing this command Example sgateway 192 168 1 1 New IP Gateway set to 192 168 1 1 32 TELNET RS 232 COMMANDS show_telnet_pass Command The show_telnet_pass command shows the Telnet password for login if required Syntax show_telnet_pass Example show_telnet_pass Telnet password reindeer show_telnet_username Command The show_telnet_username command returns the user name required for login Syntax show_telnet_username Parameters None Example show_telnet_username Telnet login andrew 33 TELNET RS 232 COMMANDS show_ver data Command The Zshow ver data command displays the hardware and firmware version of the matrix Syntax dshow ver data Parameters None Example dshow ver data Hardware version 1 Firmware Release version 2 0 33 Release data Jun 17 2012 Release time 16 50 58 Boot loader version 1 6 sipadd Command The Zsipadd command sets the IP address of the matrix Dot decimal notation must be used when specifying the IP address Syntax
4. 17 TELNET RS 232 COMMANDS EDID Management dynamic_edid Command The dynamic_edid command provides the ability to route any downstream EDID to any input When enabled the EDID is copied to all inputs from the last selected active output When disabled the EDID is copied to all inputs from the first active display detected starting from Output 1 Syntax dynamic_edid paraml Parameters param1 Value 0 1 Vue meann jDiabe Notes The default setting for Dynamic EDID is disabled Example dynamic_edid 1 Enable Dynamic EDID mode 18 TELNET RS 232 COMMANDS edidbatolo Command The edidbatolo command reads the downstream EDID and stores it to any local input Up to eight inputs can be specified Syntax tedidbatolo paraml param2 param3 param9 Parameters param1 EDID bank offset 1 3 param2 Input 1 8 Notes If param2 0 then the EDID in the specified bank is copied to all eight inputs Examples edidbatolo 2 3 Finished reading EDID from bank Z2 Finished loading EDID to local 3 edidbatolo 4 0 Finished reading EDID from bank 4 Finished loading EDID to local 1 Finished loading EDID to local 2 Finished loading EDID to local 3 Finished loading EDID to local 4 Finished loading EDID to local 5 Finished loading EDID to local 6 Finished loading EDID to local 7 Finished loading EDID to local 8 19 TELNET RS 232 COMMANDS ediddetolo Function The
5. Advanced EDID features are accessible through the RS 232 serial command set or using IP Control N IMPORTANT If the unit is installed in a closed or multi rack assembly do not block the ventilation holes of the enclosure FEATURES Features e Increases productivity e Supports resolutions up to 1920x1200 Single Link and 3840x2400 Dual Link e Front panel control buttons for local switching e Serial RS 232 interface for remote control via a computer or control automation devices e P Control e Discrete IR remote control switching e Advanced EDID management permits upload of custom internal or external EDID settings e Supports DDWG standards for DVI e Built in power supply e Output masking command e Standby mode e Grounding pin e IR Sensor e IR Extender e Status LCD shows routing status e Firmware upgrade via RS 232 e Power On Off switch Rack mountable Package Includes GefenPRO 8x8 DVI Dual Link Matrix 6 ft DVI Dual Link cables M M IR Remote Control AC Power Cord Set of Rack Ears 1 8 1 1 1 1 User Manual Sf St St N St S PANEL LAYOUT Front Panel I MATRIX SMBDL IW Lil LL Lil eu PANEL DESCRIPTIONS Front Panel Control Buttons These buttons are used to navigate the LCD menu system See pages 9 and 10 for more information lt q Left gt Right Select Select Cancel Button This button is used to cancel a routing ch
6. SxS DVI Dual Link Matrix GEF DVI S45DL PB User Manual www gefenpro com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM 5 00 PM Monday Friday Pacific Time For 24 7 support see the back of the product for the support number Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefenpro com support gefenpro com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice 8x8 DVI Dual Link Matrix is a trademark of Gefen LLC 2012 Gefen LLC All rights reserved All trademarks are the property of their respective owners Rev A9 O o co 40 0 FP ON gt CONTENTS Introduction Operation Notes Features Panel Layout Front Panel Descriptions Panel Layout Back Panel Descriptions Connecting And Operating The 8x8 DVI Dual Link Matrix Wiring Diagram Front Panel Display Front Panel Selection IR Remote Control Unit Layout and Description Installing the Battery Setting the IR Channel IR Remote Control Key Mapping EDID Management IP Configuration RS 232 Serial Control Telnet RS 232 Commands EDID Management IP Telnet Configuration Routing Masking Miscellaneous Web Interface View Matrix Status Manage EDID Masking IP Configuration Backup Restore Power Management Network Cable Wiring
7. activebolo command activates the boot loader This command is used when updating the matrix firmware See page 68 for details on this procedure Syntax activebolo Parameters None Example activebolo To download the file DVI8x8DL please type the command activebolo 0 To download the file GEFMTXFP please type the command activebolo 1 43 TELNET RS 232 COMMANDS fadefault Command The fadefault command disables the EDID lock state sets the default routing state 1 1 2 2 3 3 etc and resets the input and output names to the default names e g Output 1 Input 1 Syntax fadefault Parameters None Example fadefault Return to factor default Loading default EDID Routed 1 1 2 2 Finished loading EDID to local Finished loading EDID to local Finished loading EDID to local Finished loading EDID to local Finished loading EDID to local Finished loading EDID to local Finished loading EDID to local CO go 01 FP W NY Ln Finished loading EDID to local 44 TELNET RS 232 COMMANDS help Command The help command displays help on the specified command If param7 is not specified then the full list of commands is displayed Syntax help paraml Parameters param1 Command name Example help callpreset Cmd callpreset Recall a routing and mask state preset Syntax callpreset paraml Paraml 1 8 preset e g callpreset 2 lock_fo Command The loc
8. ediddetolo function stores the Default EDID 640x480 in the specified Local EDID inputs Up to eight inputs can be specified Syntax ediddetolo paraml param2 param9 Parameters param1 Input 1 8 Notes If param1 0 then all 8 DVI inputs will be set to the Default EDID Examples ediddetolo 7 Finished loading EDID to local 7 ediddetolo 0 Finished loading EDID to local 1 Finished loading EDID to local 2 Finished loading EDID to local 3 Finished loading EDID to local 4 Finished loading EDID to local 5 Finished loading EDID to local 6 Finished loading EDID to local 7 Finished loading EDID to local 8 20 TELNET RS 232 COMMANDS ediddstoba Function The ediddstoba function reads the downstream EDID and stores it to a specified EDID bank Syntax ediddstoba paraml param2 Parameters param1 A downstream monitor 1 8 param2 EDID bank offset 1 3 Example ediddstoba 4 2 Finished reading EDID from output 4 Finished loading EDID to bank 2 21 TELNET RS 232 COMMANDS ediddstolo Function The ediddstolo function reads the downstream EDID and stores it to a Local EDID input Syntax ediddstolo paraml param2 param3 param9 Parameters param1 A downstream monitor 1 8 param2 Input list 1 8 Notes If param2 0 then the downstream EDID is stored to all 8 DVI inputs Examples ediddstolo 2 3 Finished reading EDID from output 2 Finished loading ED
9. sipadd paraml Parameters param1 IP address Notes The matrix must be rebooted after executing this command Example sipadd 192 168 1 72 New IP set to 192 168 1 72 34 TELNET RS 232 COMMANDS snetmask Command The snetmask command sets the IP network mask Dot decimal notation must be used when specifying the IP network mask Syntax snetmask paraml Parameters param1 Network mask Notes The default net mask is set to 255 255 255 0 The matrix must be rebooted after executing this command Example snetmask 255 255 0 0 New IP Mask set to 255 255 0 0 Zuse telnet pass Command The Zuse telnet pass command requires or disables login credentials Syntax fuse telnet pass paraml Parameters param1 State 0 1 Value Meaning o Disable password Enable force password Notes The default setting is disabled Example use_telnet_pass 1 Telnet password at login is set to ON 35 TELNET RS 232 COMMANDS Routing callpreset Recalls a routing mask preset prpreset Prints the routing preset table savepreset Saves the current routing masking state to a preset r Routes the specified inputs to the specified outputs Routes the specified input to all outputs callpreset Command The callpreset command recalls a routing preset Any masked outputs will also be recalled Syntax callpreset parami Parameters param1 Preset 1 8 Example callprese
10. 0x1A 0x51 0x17 0x00 0x0A 0x20 0x20 0x20 0x20 0x20 0x20 0x00 0x00 0x00 OxFC 0x00 0x53 0x41 0x4D 0x53 0x55 0x4E 0x47 xOA 0x20 0x20 0x20 0x20 0x20 0x01 0x59 0x02 0x03 0x29 ORF 0x46 0x90 0x04 0x05 0x03 0x20 0x22 0x23 0x09 0x07 0x07 0x83 0x01 0x00 0x00 0xE2 0x00 0x0F ORFS 0x05 0x03 0x01 0x6E 0x03 0x0C 0x00 0x20 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x65 24 TELNET RS 232 COMMANDS prdsedid Function The prdsedid function reads the downstream EDID and sends it to the serial port Syntax prdsedid paraml Parameters param1 A downstream monitor 1 8 Example prdsedid 2 Finished reading EDID from output 2 0x00 OxEE OxPP OxFP OxFF OxPF OxFF 0x00 Ox4C 0x2D OxAC 0x06 0x01 0x00 0x00 0x00 0x34 0x13 0x01 0x03 0x80 0x66 0x39 0x78 0x0A OxEE 0x91 OxA3 0x54 0x4C 0x99 0x26 OxOF 0x50 0x54 OxBD OxEF 0x80 0x71 0x4F 0x81 0x00 0x81 0x40 0x81 0x80 0x95 0x00 0x95 OxOF OxB3 0x00 OxA9 0x40 0x02 0x3A 0x80 0x18 0x71 0x38 0x2D 0x40 0x58 0x2C 0x45 0x00 OxAO 0x5A 0x00 0x00 0x00 0x1E 0x66 0x21 0x50 0xBO 0x51 0x00 0x1B 0x30 0x40 0x70 0x36 0x00 OxAO 0x5A 0x00 0x00 0x00 0x1E 0x00 0x00 0x00 OxFD 0x00 0x18 0x4B 0x1A 0x51 0x17 0x00 0x0A 0x20 0x20 0x20 0x20 0x20 0x20 0x00 0x00 0x00 O0xFC 0x00 0x53 0x41 0x4D 0x53 0x55 Ox4E 0x47 OA 0x20 0x20 0x20 0x20 0x20 0x01 0x59 0x02 0x03 0x29 0xF1 0x46 0x90 0x04 0x05 0x03 0x20 0x22 0x23 0x09 0x07 0x07 0x83 0x01 0x00 0x00
11. 0xE2 0x00 0x0F O0xE3 0x05 0x03 0x01 0x6E 0x03 0x0C 0x00 0x20 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x65 25 TELNET RS 232 COMMANDS predidst Function The predidst function reads the downstream EDID This function displays a table containing details relating to the Local EDID and the monitor name Syntax prdsedid Parameters None Example prdsedid Input Source Name eee mein eee 1 Default GEFEN XPT DL 2 Output_1 3 Default GEFEN XPT DL 4 Default GEFEN XPT DL 5 External SAMSUNG 6 Output 1 7 Output 1 8 Output 26 TELNET RS 232 COMMANDS prloedid Function The prloedid function reads the local EDID of a specified input and spools it to the serial port Syntax prloedid paraml Parameters param1 A specified Input 1 8 Example prloedid 1 Finished reading EDID from Local EDID input 1 0x00 OxPF OxFF OxXFP OxPP OxFF OxFF 0x00 Ox1C OxA6 0x00 0x01 0x00 0x00 0x00 0x01 0x01 0x14 0x01 0x03 0x80 0x50 0x2D 0x78 OxOA OxOD OxC9 OxAO 0x57 0x47 0x98 0x27 0x12 0x48 0x4C 0x21 Ox4F 0x00 0x81 0x00 OxA9 0x40 0xD1 0x00 0x71 0x40 0x01 0x01 0x01 0x01 0x01 0x01 0x01 0x01 0x30 0x2A 0x00 0x98 0x51 0x00 0x2A 0x40 0x30 0x70 0x13 0x00 0x52 0x0E 0x11 0x00 0x00 0x1E OxBO 0x68 0x00 OxAO OxAO 0x40 0x2E 0x60 0x30 0x20 0x36 0x00 0x81 0x90 0x21 0x00 0x00 0x1E 0x00 0x00 0x00 DXxEC 0x00 0x47 0x4
12. 1 Disable 5V Enable 5V Example f 11 Enable FO 1 49 TELNET RS 232 COMMANDS Command The lower case L command displays the link status of each input If the input is receiving a dual link signal then the Link status will be set to Dual Ifa single link source is used then the Link status will be set to Single syntax 1 Parameters None Example 1 Input signal Link 1 NONE Single 2 NONE Single 3 NONE Single 4 NONE Single 5 NONE Single 6 NONE Single 7 NONE Single 8 NONE Single 50 TELNET RS 232 COMMANDS m Command The m command displays the current matrix status and routing information Syntax m Parameters None Example m Output Input HPD Status eee a a E A Output Input 1 LOW ACTIVE Output_2 Input_2 HIGH ACTIVE Output_3 Input_3 LOW ACTIVE Output 4 Input 4 LOW ACTIVE Output Input o LOW ACTIVE Output Input 6 LOW ACTIVE Output 7 Input 7 LOW ACTIVE Output_8 Input_8 LOW ACTIVE EDID lock state Power lock state RMT IR SW1 0 SW2 1 51 WEB INTERFACE View Matrix Status Matrix Status Displays the current routing status of each input and output on the matrix 8x8 DL DVI Manager was eon Maskina IP CONFIGURATION DACKUPIRESTORE POWER MANAGEMENT i IF Output_2 Outpt SJS Refresh Auto Refresh Refresh Auto Refresh Click to
13. CA 91311 1 800 545 6900 WWW gefenpro com 65 818 772 9100 AR support gefenpro com Ce Rev A9 fax 818 772 9120
14. DIP switch bank is located underneath the battery cover Channel 0 Channel 1 Default Channel 2 Channel 3 1 2 1 2 1 2 1 2 Battery compartment of the IR remote showing the exposed DIP Switch bank between the battery chambers It is important that the IR channel on the Remote Control unit matches the IR channel set on the 8x8 DVI Dual Link Matrix For example if both DIP switches on the IR Remote Control unit are set to IR channel 0 both DIP switches down then the 8x8 DVI Dual Link Matrix must also be set to IR channel 0 See page 46 on how to change the IR channel on the 8x8 DVI Dual Link Matrix 13 IR REMOTE CONTROL UNIT IR Remote Control Key Mapping Each input and output on the 8x8 DVI Dual Link Matrix is represented by a button on the IR Remote Control unit The table below lists the corresponding inputs and outputs Remote Button Monitor Source Routing Sources using the IR Remote Control unit Issuing a routing command is a two step process The first step is to select the monitor where the source will be routed The second step is to select the source Example 1 Route the source device connected to In 7 to the monitor connected to Out 3 1 Press button 3 monitor 3 on the IR remote control unit 2 Press button 7 source 7 on the IR remote control unit The source connected to In 7 will be routed to the monitor connected to Out 3 Example 2 Route the source device connected to In 1 to
15. Diagram Firmware Update Rack Mount Safety Information Specifications Warranty Licensing INTRODUCTION Congratulations on your purchase of the GefenPRO 8x8 DVI Dual Link Matrix Your complete satisfaction is very important to us GefenPRO In the realm of video distribution certain features are invaluable in acommercial or broadcast environment Accommodations such as a build in power supply and flat black rack mount enclosures set GefenPRO apart from our traditional products Complex distribution units allow for professional DVI 3G SDI and HDMI signals to be routed and converted easily and seamlessly while being backed up by a renowned and dependable technical support team Gefen invites you to explore the GefenPRO product line and hopes that you find the solution that fits your needs The GefenPRO 8x8 DVI Dual Link Matrix This product simplifies the process of routing up to eight DVI sources to any of eight DVI monitors without losing quality or resolution The GefenPRO 8x8 DVI Dual Link Matrix provides a simple reliable and highly effective method of streamlining any installation using multiple sources and outputs taking the hassle out of managing multiple connections Each DVI source is accessible from any monitor by using the front panel buttons IR remote unit built in RS 232 or using IP Control How It Works The GefenPRO 8x8 DVI Dual Link Matrix has eight DVI inputs and eight DVI outputs Using the supplied DVI dual l
16. Input 7 Input 8 Set Default EDID Set Default EDID Place a check mark next to the input s that should be set to the default EDID Click the Set Default EDID button to apply the default EDID to the selected inputs 57 WEB INTERFACE Upload EDID Upload EDID Press this button from the Manage EDID screen to access this menu system VIEW MATRIX STATUS MASKING IP CONFIGURATION DACKUPRESTORE POWER MANAGEMENT Setingutto Defaut EDID Dumas eon cem puo EDI Lock tma Input_3 Ingul Select Input s to Upload to Input 1 Input 2 Input 3 Input 6 Input 7 Input 8 Upload EDID File Load EDID file Load EDID file Place a check mark next to the input s that will receive the EDID data from the file The EDID file must be in bin format Click the Browse button to locate the EDID on the computer Click the Load EDID file button to upload the EDID file to the matrix 58 WEB INTERFACE Download EDID Download EDID Press this button from the Manage EDID screen to access this menu system Download EDID EDID Status Lock State OFF input_t Default GEFEN_XPT_OL m En Cava te GER ERE Downicad EDID File in PC EET ACE Retest Select EDID to Download C Qutput_1 gt Output 2 O Output 6 O Output 7 Download EDID File to PC Download EDID File to PC Select the radio button next to the output containin
17. State Power Lock State In the case of an accidental power loss to the matrix the 5V state for each input can be preserved Set the specified Power Status buttons see previous page and click the radio button next to ON Click the Update Power Lock State button to apply changes By default this option is set to Off 66 NETWORK CABLE WIRING DIAGRAM Gefen recommends the TIA EIA 568 B wiring option Please adhere to the table below when field terminating the cable for use with Gefen products Fm Color 3 Green Wie L4 po I Cabling comes in stranded and solid core types Gefen recommends using solid core cabling It is recommended to use one continuous run from one end to the other Connecting through a patch is not recommended 67 FIRMWARE UPDATE Firmware Update Procedure The following items are required to update firmware RS 232 Terminal e g Windows based PC running HyperTerminal RS 232 cable do not use a null modem cable Firmware file DVI8x8DL version nonKVM bin download the firmware file from the Support gt Downloads section of the Gefen Web site To begin the update procedure the matrix Boot Loader must be activated To activate the Boot Loader please follow the procedure below 1 2 Power on the matrix Connect an RS 232 cable to the PC and open the terminal program using the following settings Baud rate 19200 Stop bits 1 Data bits 8 Flow control
18. monitors are used such as with the 8x8 DVI Dual Link Matrix it is important to use devices monitors that have similar or compatible resolutions and features This will ensure that the single video audio signal produced by the source device is accepted by all of the connected output devices monitors The user has the option through utilization of the RS 232 serial interface to choose how the unit will manage the EDID from multiple DVI devices monitors Therefore the user has some control over the resolutions and features that the source devices will output The 8x8 DVI Dual Link Matrix has a Local EDID management mode that will control how the EDID information is handled How do I change EDID modes in the 8x8 DVI Dual Link Matrix EDID modes are managed via Telnet RS 232 control pages 17 27 or through the built in Web interface pages 56 61 15 IP CONFIGURATION Configuring the IP Address The 8x8 DVI DL Matrix supports IP based control using Telnet or the built in Web based GUI To set up IP control the network settings for the 8x8 DVI DL Matrix must be configured via RS 232 The default network settings for the matrix are as follows IP Address 192 168 1472 Subnet Doa Doug Gateway 192 168 1 254 HTTP Port 80 Telnet Port 23 1 2 Connect an RS 232 cable from the PC to the 8x8 DVI DL Matrix Launch a terminal emulation program e g HyperTerminal and use the following settings Baud Rate 19200 Data Bit
19. the following screen is displayed After a few moments the Standby Screen is displayed The Standby Screen is shown below Displaying the Firmware Version Pressing the button on the front panel will display the current firmware version Displaying the Bootloader Version Press the lt button to display the bootloader version Press the lt button once more to return to the Standby Screen NOTE The Cancel button can be pressed at any time to return to the Standby Screen FRONT PANEL DISPLAY Displaying the Routing Status From the main screen press the Select button When the arrow cursor is next to OUTPUT pressing the or gt buttons on the front panel will show the current routing state of each input and output The illustration below shows the routing state of output 1 Note that the number displayed next to INPUT may be different than the Illustration above depending upon the current routing state Routing Sources Example Route the source device connected to In 2 to the monitor connected to Out 1 1 From the Standby Screen press the Select button on the front panel to display the routing status screen Press the Select button again to move the cursor to INPUT Press the button to set the source to Input 2 The source device connected to In 2 is now routed to the monitor connected to Out 1 Press the Cancel button to return to the standby screen NOTE The Cancel button
20. the monitor connected to Out 1 1 Press button 1 monitor 1 on the IR remote control unit 2 Press button 1 source 1 on the IR remote control unit The source connected to In 1 will be routed to the monitor connected to Out 1 14 EDID MANAGEMENT EDID What is it and what is it used for Under normal circumstances a source device digital and analog will require information about a connected device monitor to assess what resolutions and features are available The source can then tailor its output to send only resolutions and features that are compatible with the attached device monitor This information is called EDID Extended Display Information Data and a source device can only accept and read one EDID from a connected device monitor Likewise the source an only output one resolution for use by a connected device monitor Why is EDID so important with the 8x8 DVI Dual Link Matrix The 8x8 DVI Dual Link Matrix is a complex piece of technology that replicates and switches between multiple inputs and outputs Each connected source device will require one EDID to read EDID management is carefully handled by the 8x8 DVI Dual Link Matrix to provide a single EDID for each source to read What options do I have to manage the EDID in the 8x8 DVI Dual Link Matrix First it is important to note that each source device can only output one video audio signal type This includes resolutions and timings When multiple devices
21. 5 Chput T put amp Sales Se cs an ie ib Inputa ru Input 1 Input 2 Input 3 input 4 Input 5 sn a oeae ot Independent Audio Switch Ma Yeu Dupa 8 Ing Input 1 Input 7 Input 3 ing 4 ingat 1 Peresh Auto Figfresh Input amp input 7 Input B E Fresets Current Routing State to Preset 1 Save Prasat uting Starte 1 Recall Presa Ou pul Harme 1 K Save Output Nama Input 1 Save Input Mama Save Preset Click the down arrow on the pull down list to select the preset Presets location 1 16 Click the Save Provides saving and Preset button to save the preset recalling of routing states Presets Save Current Routing State to Preset Recall Routing State Recall Preset Recall Preset Click the down arrow on the pull down list to select the routing state 1 8 to recall Click the Recall Preset button to recall the preset 54 WEB INTERFACE 8x8 DL DVI Manager se con masking iP CONFIGURATION nackupmestore POWER MANAGEMENT j Switch Outputs Outputs Out 1 Output_2 OT Taput Output Duis 8 Cipt T Output B Inputs Input 1 Input 2 Input 3 kpi 4 Input 5 Input 5 Input 7 Input n Input 1 Input 2 Input 3 inui 4 ingat 5 Rohesh Auto Refresh Input 6 Input 7 Input 8 cem Presets Recall Routing Sana 1 Recall Preset Rename I O Provides custom naming of each input and output on the matrix Output Output Name Ir Output_1 Save Output Name
22. 5 0x46 0x45 Ox4E Ox5F 0x58 0x50 0x54 Ox5F 0x44 0x4C 0x20 0x00 0x00 0x00 OxFD 0x00 0x3B 0x3D 0x0F 0x71 0x1C 0x00 0x0A 0x20 0x20 0x20 0x20 0x20 0x20 0x00 0x3C 27 TELNET RS 232 COMMANDS IP Telnet Configuration Zshow ver data Displays the hardware and firmware version of the matrix Zsipadd Sets the IP address of the matrix Zuse telnet pass Use password during Telnet sessions Zdisplay telnet welcome Command The Zdisplay telnet welcome command sets enables disables the Telnet welcome message on login Syntax display telnet welcome paraml Parameters param1 State 0 1 IN message Example fdisplay telnet welcome 1 Telnet welcome at login is set to ON 28 TELNET RS 232 COMMANDS ipconfig Command The ipconfig command displays the current TCP IP settings for the matrix Syntax ipconfig Parameters None Example ipconfig MAC add 00 10191701 250707 TP add 192 100 1272 Net Mask 255 255 255 0 Gateway 192 168 2 1 Web Server Port 80 Telnet Server Port 23 Telnet password at login is set to ON Telnet welcome at login is set to ON 29 TELNET RS 232 COMMANDS resetip Command The resetip command resets all TCP IP settings to factory defaults Syntax resetip Parameters None Notes The matrix must be rebooted after executing this command Example resetip Reset ip configuration to factory default set_http_port Command The Zs
23. D from output 2 Finished loading EDID to local 7 r d All outputs are routed to input 1 39 TELNET RS 232 COMMANDS s Command The s command routes the specified input to all outputs Syntax s paraml Parameters param1 Input 1 8 Example s 1 All outputs are routed to input 1 40 TELNET RS 232 COMMANDS Masking Masks the selected video output s Unmasks the selected output s maskout Command The maskout command allows blanking of the specified outputs Syntax maskout paraml param2 Parameters param1 Output 1 8 param2 State O 1 o Ae o Notes The current masking state will be lost if power is interrupted or if the masking state is not saved see savepreset on page 38 Example maskout 2 0 Mask outputs 2 41 TELNET RS 232 COMMANDS unmaskout Command The unmaskout command unmasks the specified outputs If param 0 then all outputs will be unmasked Syntax unmaskout paraml param8 Parameters param1 Output 1 8 Examples unmaskout 3 5 7 Activate outputs 3 5 7 unmaskout O0 Activate all outputs 42 TELNET RS 232 COMMANDS Miscellaneous Atome uem Displays the voltages of the internal boards Zshow voltage Displays the voltages of the internal boards Toggles displays 5V input l Displays the dual link single link status table Displays the current routing status activebolo Command The
24. ID to local 3 ediddstolo 2 0 Finished reading EDID from output 2 Finished loading EDID to local 1 Finished loading EDID to local 2 Finished loading EDID to local 3 Finished loading EDID to local 4 Finished loading EDID to local 5 Finished loading EDID to local 6 Finished loading EDID to local 7 Finished loading EDID to local 8 22 TELNET RS 232 COMMANDS lock_edid Function The lock_edid function secures the Local EDID and disables the automatic loading of the downstream EDID after the Matrix is powered on Syntax lock_edid paraml Parameters param Input 0 1 Value meann O Disable Example lock edid O Disable Lock EDID mode 23 TELNET RS 232 COMMANDS prbaedid Function The prbaedid function reads the EDID file from the specified bank and sends to serial port Syntax prbaedid paraml Parameters param1 EDID bank offset 1 3 Example prbaedid 2 Finished reading EDID from bank Z2 0x00 OxFF OxFF OxFF OxFF OxFF OxFF 0x00 Ox4C Ox2D OxAC 0x06 0x01 0x00 0x00 0x00 0x34 0x13 0x01 0x03 0x80 0x66 0x39 0x78 OxOA OxEE 0x91 OxA3 0x54 0x4C 0x99 0x26 xOP 0x50 0x54 OxBD O xEF 0x80 0x71 0x4F 0x81 0x00 0x81 0x40 0x81 0x80 0x95 0x00 0x95 Ox F 0xB3 0x00 OxA9 0x40 0x02 0x3A 0x80 0x18 0x71 0x38 0x2D 0x40 0x58 0x2C 0x45 0x00 0xA0 0x5A 0x00 0x00 0x00 OxLE 0x66 0x21 0x50 0xBO 0x51 0x00 0x1B 0x30 0x40 0x70 0x36 0x00 OxAO 0x5A 0x00 0x00 0x00 0x1E 0x00 0x00 0x00 OxFD 0x00 0x18 0x4B
25. None Type the command activebolo Two options will be provided To download the file DVI8x8 to the matrix type the command activebolo 0 Type the command activebolo 0 This will begin the update process of the main board Once the Boot Loader is activated the following message should appear Press 1 on the computer keyboard to begin downloading program to the temporary memory DVI8x8 Boot Loading Download new program Cancel Press 1 on the computer keyboard to begin downloading program to the temporary memory 68 FIRMWARE UPDATE A message will appear in the terminal program Waiting for the file to be sent press a to abort In Hyperterminal click Transfer gt Send file Click Browse and select the BIN file corresponding to the boot loader which was activated In this first case the file should start with DVI8x8 Select Ymodem for the protocol Press Send on the Send File dialog box A message will appear in Hyperterminal Programming Completed Successfully The unit will exit the boot loader screen and return to the standard Hyperterminal window 69 RACK MOUNT SAFETY INFORMATION Maximum recommended ambient temperature 45 C 104 F Increase the air flow as needed to maintain the recommended temperature inside the rack Do not exceed maximum weight loads for the rack Install heavier equipment in the lower part of the rack to maintai
26. Save button to apply changes 63 WEB INTERFACE Backup Restore The Backup Restore feature for the 8x8 DVI Dual Link Matrix is not currently implemented and will be available in a future release of the firmware CELEP 8x8 DL DVI Man This feature will be implemented in a future release z o Buewse 64 WEB INTERFACE Power Management Power Status Enabling this feature will store the 5V status for that input prior to shutting down the matrix This preserves the 5V state when the unit is restarted Cu 8x8 DL DVI Manager VIEW MATRIX STATUS Power Lock State Update Power Lock State Auto Refresh Power State The current power state is Save Changes listed under Refresh the column Click to refresh titled 5 Volt the Power Auto Refresh Click these Status screen Check this box buttons to to automatically toggle the update the input power Save Changes screen every 10 state Click to save the seconds power lock status WARNING Use caution when applying power to inputs as this may damage your equipment 65 WEB INTERFACE ZP 8x8 DL DVI Manager view MATRIX STATUS manage eno MASKING ie conrisuranon nackupmestore EEE Warning Use caution when applying power to inputs It may damage your equipment e Changes Power Lock State Update Power Lock State 9 O O On Power Lock State Update Power Lock
27. THE 8X8 DVI DUAL LINK MATRIX How to Connect the 8x8 DVI Dual Link Matrix 1 Connect up to 8 DVI Dual Link source devices to the inputs on the rear panel of the 8x8 DVI Dual Link Matrix using the supplied DVI dual link cables 2 Connect up to 8 DVI Dual Link monitors to the outputs on the rear panel of the 8x8 DVI Dual Link Matrix with user supplied DVI dual link cables 3 Connect the included AC power cable to the power receptacle on the rear panel of the 8x8 DVI Dual Link Matrix and connect the opposite end of the power cable into an available electrical outlet How to Operate the 8x8 DVI Dual Link Matrix The 8x8 DVI Dual Link Matrix offers a number of control options The following methods can be used to control basic routing functions 1 Front Panel Control Buttons Pages 9 and 10 2 IR Remote Control Pages 11 14 3 Telnet RS 232 Serial Control Pages 16 51 4 Web interface Contol Pages 52 66 Wiring Diagram for the GefenPRO 8x8 DVI Dual Link Matrix Gefen zz e nv DUAL LINK CABLE mmm DVI Dual Link Sources 8x DVI Dual Link Displays GEF D VI 848DL ATTENTION This product should always be connected to a grounded electrical socket FRONT PANEL DISPLAY Main Display The Main Display of the GefenPRO 8x8 DVI Dual Link Matrix is a 16 character 2 line display This display will show the standby screen and will also be used to aid in performing routing commands When the unit is powered on
28. airs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 72 LICENSING IwIP is licenced under the BSD licence Copyright c 2001 2004 Swedish Insti
29. ange in progress IR Window Receives signals from the IR Remote Control unit Power Indicator This LED indicator will glow red when the power is turned on Power Switch Turn the power on or off using this switch LCD Display Displays the current routing status of the Matrix and is also used to manage source routing PANEL LAYOUT Back Panel PANEL DESCRIPTIONS Back Panel 110 220 V AC 50 60 Hz Power Receptacle Connect the included AC power cord from this receptacle to an available electrical outlet Fuse Drawer Each power receptacle houses a fuse drawer Within each fuse drawer are two 2 250 V fuses One fuse is active and the other is a spare DVI Input Ports 1 8 Connect DVI source devices to these ports Grounding Terminal Provides a discharge path to ground in case a short circuit occurs between the hot lead of the power supply and the enclosure of the Matrix The grounding wire should be attached from the grounding terminal to an approved ground path IP Control Interface Connect to this port to control the 8x8 DVI Dual Link Matrix using IP Control See page 16 for details IR Extender Port Connect an IR extender cable to this port Gefen part no EXT RMT EXTIR DVI Output Ports 1 8 Connect DVI monitors to these ports RS 232 Serial Port Connects to the RS 232 control device The 8x8 DVI Dual Link Matrix may be switched remotely using this port See page 17 for more information CONNECTING
30. can be used to return to the standby screen at any time 10 IR REMOTE CONTROL UNIT Layout and Description RMT 848IR N 1 LED Button Press Indicator This LED will be activated momentarily each time a button is pressed 2 Display and Source Selection Buttons These buttons are used to select which source is routed to a display oee page 14 for information on using the IR Remote Control unit NOTE An Activity Indicator that flashes quickly while holding down any one of the 16 buttons indicates a low battery Replace the IR Remote Control battery as soon as possible 11 IR REMOTE CONTROL UNIT Installing the Battery 1 Remove the battery cover on the back of the IR Remote Control unit 2 Insert the included battery into the open battery slot The positive side of the battery should be facing up 3 Replace the battery cover The Remote Control unit ships with two batteries One battery is required for operation and the other battery is a spare Battery Slot CAUTION Risk of explosion if battery is replaced by an incorrect type Use only 3V lithium battery type CR 2032 12 IR REMOTE CONTROL UNIT Setting the IR Channel In the event that IR commands from other remote controls interfere with the supplied IR Remote Control unit changing the IR Remote Control s IR channel will fix the problem The IR Remote Control unit has a bank of DIP switches used for setting the IR channel The
31. e output is already masked then the button will read Active enabled Click the Active button again to toggle the masking state to Mask disabled 62 WEB INTERFACE IP Configuration IP Settings Assigns IP address subnet gateway HTTP listening port and Telnet port Note that the MAC address can not be changed Click the Save button to apply changes The matrix must be rebooted for the changes to take effect 8x8 DL DVI Manager view mateix STATUS manage en n wasna EEE cackupmerstore power MANAGEMENT defauft TEA 188 1 72 Subnet 255255 2550 dwinuff 255 255 255 0 Gamma 19216821 defaut 182 168 1 254 HTTP Port 0 default BO Telnet Por 23 deian 255 Save Reset IP Configuration to Defaults Reser Telnet Login Settings User Hame Admin decnult Ac Password Admin default Ad Force Logn Iz Welcome message Save IP Settings MAC Address 00 1C 91 01 50 07 IP Address 192 168 2 236 default 192 168 1 72 Subnet 255 255 255 0 default 255 255 255 0 Gateway 192 168 2 1 default 192 168 1 254 HITP Port oU default 80 Telnet Port 23 default 25 Reset IP Configuration to Defaults Telnet Login Settings User Name Admin default Admin Password Admin default Admin Force Login V Welcome message Save Telnet Login Settings Sets the user name and password for Telnet sessions to the matrix Click the
32. ength for param2 is 15 characters Special characters and spaces are not permitted If required use the underscore character to separate characters Syntax fset output name parami param2 Parameters param1 Output 1 16 param2 Name Example set_output_name 3 display_3 display_3 is assigned to output 3 show_temp The show_temp command provides temperature information for the matrix syntax show_temp Parameters None Example show_temp Temperature near main power supply is 45 Temperature near cross point is 53 Temperature near power supply input board is 47 47 TELNET RS 232 COMMANDS show_ voltage The Zshow voltage command provides voltage information for the matrix Syntax fshow voltage Parameters None Example fshow voltage Voltage 3 3 measured 3344 mV Voltage 5 measured 5036 mV Voltage 12 measured 11905 mV Voltage 1 2 measured 1200 mV Voltage 1 8 measured 1800 mV Voltage 3 3 measured 3265 mV 48 TELNET RS 232 COMMANDS f Command Enables disables 5V on pin 14 of the specified DVI input This command is used when connecting the Receiver module of fiber optic extenders which require 5V N WARNING Before connect a computer to the DVI input make sure to disable the 5V on the DVI input Otherwise the video card on the computer may become damaged Syntax f paraml param2 Parameters param1 Input 1 8 param2 State 0
33. et http port command sets the Web server listening port Syntax fset http port paraml Parameters param1 Port 0 65535 Notes The default port setting is 80 The matrix must be rebooted after executing this command Example fset http port 34 New HTTP port set to 34 30 TELNET RS 232 COMMANDS set_telnet_pass Command The set_telnet_pass command sets the Telnet password The maximum length of the password is 20 characters The password is case sensitive Syntax set_telnet_pass paraml Parameters param1 Password Notes The default password is Admin The matrix must be rebooted after executing this command Example tset telnet pass reindeer Telnet password updated to reindeer Ziset telnet port Command The Zset telnet port command sets the Telnet listening port Syntax fset telnet port paraml Parameters param1 Port 0 65535 Notes The default port setting is 23 The matrix must be rebooted after executing this command Example fset telnet port 80 New Telnet port set to 80 31 TELNET RS 232 COMMANDS set_telnet_ username Command The set_telnet_username command sets the Telnet user name The maximum length of the user name is 20 characters The user name is case sensitive Syntax set_telnet_username paraml Parameters param1 User name Notes The default username is Admin The matrix must be rebooted after executing this command Example
34. g the EDID to be downloaded Click the Download EDID File to PC button to confirm the change The downloaded EDID file will be in bin format 59 WEB INTERFACE Copy EDID Copy EDID Press this button from the Manage EDID screen to access this menu system EDID Status Lock State OFF EDD gt Source Mame GEFEN PTDL TUE mpi 4 Dua GEFEN APT DL inputs Dotun Geren eTo ngu s Dea ceren XPT DL input Deut GEFEN DET DL Select Inp Select Source to Copy from Output s O Output 1 Output 2 D Output 3 Output_6 Output_7 Output 8 Input s O Input 1 Input 2 O Input 3 C O Input 6 O Input 7 O Input 8 Select Input s to Copy to Input 1 JInput 2 Input 3 a input_6 _Input_7 Input 8 Select Source to Copy from Select Input s to Copy to Click the radio button next to the input or output containing the EDID to copy Note that only a single input or output can be selected at a time Place a check mark next to the input s where the EDID will be copied Click the Set EDID button to confirm the operation 60 WEB INTERFACE EDID Lock State EDID Lock State EDID Lock State Press this button from the Manage EDID screen to access this menu system 8x8 DL DVI Manager view marex status EEE cons ie conrisuraron sacs Setingut to Greta ED Upload EMD
35. ink cables connect 8 sources to the DVI input ports on the GefenPRO 8x8 DVI Dual Link Matrix Connect the GefenPRO 8x8 DVI Dual Link Matrix to the monitors Plug in the power cord and power on the GefenPRO 8x8 DVI Dual Link Matrix The connected monitors will show video according to the routing selection NOTE The GefenPRO 8x8 DVI Dual Link Matrix only supports DVI D The DVI connectors on the 8x8 DVI Dual Link Matrix have all 29 pins OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE GEFENPRO 8X8 DVI DUAL LINK MATRIX The 8x8 DVI Dual Link Matrix does not support HDCP content When the Matrix is used for the first time make sure that a DVI monitor is powered and connected to one of the DVI outputs on the 8x8 DVI Dual Link Matrix before applying power By default the Local EDID is read from the connected monitor and is copied to all 8 DVI inputs once the Matrix has been turned on If a monitor is not detected by the Matrix at power on a default internal EDID of 640x480 will be used This functionality can be disabled using the Secure Local EDID function through Telnet RS 232 control see page 23 or via the built in Web interface see page 61 There is no internal scaling in the 8x8 DVI Dual Link Matrix Each monitor attached to the Matrix must be able to display the resolutions output by the source device s For maximum compatibility it is recommended that only one common resolution be used by each source device
36. k_fo enables disables the power lock state Enabling this feature will store the 5V status for each input prior to shutting down the matrix This pre serves the 5V state when the unit is restarted Syntax lock_fo paraml Parameters param1 State 0 1 Value meann l0 Disable power lock Enable power lock Example Tlock fo 0 Disable Lock power mode 45 TELNET RS 232 COMMANDS set_input_name Command The Zset input name command provides a name to the selected input For example Input 1 could be renamed as Computer 1 The maximum string length for param2 is 15 characters Special characters and spaces are not permitted If required use the underscore character _ to separate characters Syntax set_input_name paraml param2 Parameters param1 Input 1 16 param2 Name Example set_input_name 5 computerl computerl is assigned to input 5 set_ir Command The set_ir set the IR channel for the matrix The associated DIP switch settings for the IR remote control unit are returned See page 13 for details on setting the IR channel for the IR remote control Syntax set_ir paraml Parameters param1 Channel 0 3 Example rset ir 2 RMT IR SW1 0 SW2 1 46 TELNET RS 232 COMMANDS set_output_name Command The Zset output name command provides a name to the selected output For example Output 1 could be renamed as HDDisplay The maximum string l
37. n stability Connect a bonding wire between an approved safety ground and the grounding screw on the chassis 70 SPECIFICATIONS Video Amplifier BanawlGlli ssuscci iine err aee re aua cepa nun nah rep rRRnnen 2x165MHz Ward reip soie aaa DVI I 29 Pin Female digital only mises PATe e RID 10 70 MERERI NN ER REIR PRO RATEN E DB 9 serial F IR NIE OST e cr 3 5mm mini stereo CON ION ORINOCO P RJ 45 Power Supply nenn 100 to 240V AC IEC connector Power Consumption M 90 Watts max Operating Temperature 32 F to 104 F 0 C to 40 C Storage Temperature sess 4 F to 140 F 20 C to 60 C Relative Humidily cross 20 to 90 RH no condensation Dimensions W x H x D 17 25 x 3 5 x 12 488mm x 89mm x 304mm SnipDIng Weigh rennen 21 Ibs 9 5 kg 71 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such rep
38. refresh the Matrix Check this box to enable Auto Status screen Refresh The Auto Refresh function automatically refreshes the interface every 10 seconds 52 WEB INTERFACE Switch Outputs Used to route the specified input to the selected output s To route a source place a check mark next to each Output Next click the radio button next to the desired Input Press the Switch button to apply the routing change Switch Outputs Outputs Output 1 lOutput_2 Output 3 Output 6 JOutput 7 Output 8 Inputs O Input 1 C Input 2 O Input 3 Input 6 Input 7 Input 8 8x8 DL DVI Ma VIEW MATRE STATUS MANAGE EDID mas Ie CONFIGURATION BACKUPRESTORE POWER MANAGEMENT Matrix Stabue Switch Out ra Audio TOI pot 2 Toms Dow Doms deem z Ae Ee Culpa amp up LT Dutput B EH 3 E Inputs t Output 4 input 1 Input 1 Ingut 3 ipid inp 5 ee men Die os Gua E input 6 Aci input I independent Audio Switch Oupa 8 inputs Actis He Yes Input 1 Input 2 Input 3 inp d Ingut 5 Retresh Auto Ratresh Input Input T Input f Presets p State to Preset 1 Save Preset Recall Preset Switch Click this button to apply the routing change 53 WEB INTERFACE 8x8 DL DVI Manager use eon askna IP CONFIGURATION DACKUPIRESTORE POWER MANAGEMENT Switch Outputs F inpur States Audio Outputs ae preat Output 1 Output 2 Output 3 aput 4 Output
39. s 8 Parity None Stop Bits 1 Flow Control None NOTE Depending upon the network the IP address subnet mask gateway IP Telnet port and HTTP port will need to be set Consult your network administrator to obtain the proper settings Set the IP address for the matrix using the sipadd command see page 34 for details Set the subnet mask using the snetmask command see page 35 for details Set the gateway router IP address using the sgateway command see page 32 for details Set the Telnet listening port using the set_telnet_port command see page 31 for details Set the HTTP listening port using the set_http_port command see page 30 for details Power cycle the matrix to reboot and complete all IP setting changes Type the IP address that was specified in step 3 in a Web browser to access the Web interface or use the same IP address to Telnet to the matrix 16 RS 232 SERIAL CONTROL 9876 6789 Only Pins 2 RX 3 TX and 5 Ground are used on the RS 232 serial interface RS232 Settings Bits DER Se CONG a acetate TTE EROR 19200 Bicis ee 8 PA seen MO dad QU Dad energie None SIOD DIUS eee adem ones E EE E MG dr os putt tia es dal casis O 1 aio dero Ret E TERe None IMPORTANT When sending RS 232 commands a carriage return and a ine feed character must be included at the end of each line RS 232 Telnet commands parameters and device names are not case sensitive
40. t 4 Recall Saved Set 4 36 TELNET RS 232 COMMANDS prpreset Command The prpreset command displays the routing preset table Syntax prpreset Parameters None Example prpreset Pr eser Ourl 2 o p wo p oi 9 T o8 1 IM O M OIM O M O M O M O M O M O 2 JA 1 JA 1 A 3 A 4 A SIA LIA TIA 8 3 IM O M OIM O M O M O M O M O M O 4 IM O M OIM O M O M O M O M OJM O 5 M O JM OIM O M O M O M O M O M U 6 IM O M OIM O M OIM OIM O M OIM O n IM O0 M OIM O M OIM OIM O M OIM O 8 IM O M OIM O M O M O M O M O M O 37 TELNET RS 232 COMMANDS savepreset Command The savepreset command saves the current routing state to the specified preset Any masked outputs will also be saved as part of the current routing state Syntax savepreset paraml Parameters param1 Preset 1 8 Example savepreset 5 Saved current as set 5 38 TELNET RS 232 COMMANDS r Command The r command routes the specified input to the specified outputs Syntax r paraml param2 param3 param9 Parameters param1 Input 1 8 param2 Outputs 1 8 Notes If param2 0 then the specified input is routed to all outputs Examples r 7 3 4 5 6 1 2 Input 7 is routed to outputs 345612 If Dynamic EDID see page 18 is enabled then the last output in the list will be saved to the specified input param1 as shown below r 7 3 4 5 6 L2 Input 7 is routed to outputs 3 45 61 2 Finished reading EDI
41. tute of Computer Science All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission THIS SOFTWARE IS PROVIDED BY THE AUTHOR AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE 73 MA GEF DVI 848DLx 20600 Nordhoff St Chatsworth
Download Pdf Manuals
Related Search