Home

Eaton FERRUPS

1. Advertencias de Seguridad INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONES Este manual contiene instrucciones importantes gue debe seguir durante la instalaci n y el mantenimiento del SIE de las baterias Por favor lea todas las instrucciones antes de poner en funcionamiento el eguipo y guarde este manual para referencia en el futuro A Este SIE contiene VOLTAJES MORTALES Todas las reparaciones y el servicio t cnico deben ser efectuados SOLAMENTE POR PERSONAL DE SERVICIO TECNICO AUTORIZADO No hay NINGUNA PARTE QUE EL USUARIO PUEDA REPARAR dentro del SIE ADVERTENCIA e Este SIE contiene su propia fuente de energia las baterias Los receptaculos de salida pueden transmitir corriente el ctrica aun cuando el SIE no est conectado a un suministro de corriente alterna c a No retire o desenchufe el cable de entrada mientras el SIE se encuentre encendido Esto uprime la descarga a tierra de seguridad del SIE y de los equipos conectados al SIE ubierto con temperatura y humedad controladas libre de contaminantes conductores a temperatura ambiente no debe exceder los 40 C No trabaje cerca del agua 0
2. 95 1 5 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 13 www eaton com powerguality SAFETY WARNINGS
3. 5 Communication The FERRUPS Rack Mount UPS is capable of full duplex communication and can communicate with a computer a Local Area Network LAN or a multi user computer system If your system comes with UPS monitoring and automatic shutdown software the FERRUPS Rack Mount UPS can communicate with that software If your system does not have software you can use the CheckUPS Power Management Software included on the Software Suite CD If you do not plan to use CheckUPS II software or other UPS monitoring software you can still set up RS 232 communication with the UPS and use commands and parameters to control UPS operation Software Suite CD Each UPS ships with the Software Suite CD and a communication cable To begin installing CheckUPS II software refer to the instructions accompanying the Software Suite CD CheckUPS ll software uses an RS 232 serial link to communicate with the UPS and using Microsoft Windows it provides you with up to date graphics of UPS power and system data and power flow It also gives you a complete record of critical power events and notifies you of important UPS or power information If there is a power outage and the UPS system battery power becomes low CheckUPS II software can automatically shut down your computer system to protect your data before the UPS Low Battery shutdown occurs NOTE You can download the latest software version from www eaton com powerguality
4. 1p no TH yelmon acdareiag and UPS EEONALOUO TOV etvat ue UPS T va LELDOETE TLPKAYL G NAEKTPONANELAG EYKATAOTNOTE TO UPS oe EOMTEPIK x po edeyx uevn Bepuokpacio vypacia o va unv TEPLEXEL ayoyya v H Oepuorpaoia eptB A Aovroc TpETEL va e7tepv et 40 C Mn ypnowonotette UPS Kovr vep vypaoia u yvotn Tum 95 Tia v cuu oveit ue LE VI TP TUTO KUL TOUS KOVOVLOHLO G KAAW LWONG pevua yn oA kAnpov Tov E OT LGLOV TOV eivat OLV E ELLEVOG ue Tv 656060 tov OVYKEKPIUEVOu UPS mp net vo eivat uey 0rtepo and 1 5 mA NPOZOXH Ot ovoompevt s UNOPEt va npokoA oovv NAEKTPONANELA N YKOVLLO ynA pevuo AauB vete TIG KOTOMMAEG TPOOVAGEELG e ATOITEITAI 616060 CUCOWPEVTOV ELTE 060 6 KOVOVLOLOVG TOV UTULTNOELG 61006076 tovc e Tlot unv orn OWTL UTOPEI va Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality SAFETY WARNINGS Avvisi di sicurezza IMPORTANTI ISTRUZIONI DI SICUREZZA CONSERVARE OUESTE ISTRUZIONI II presente manuale contiene import
5. 250 Ib 113 4 kg 50 Hz Models UPS Weight UPS Weight Battery Cabinet Without Battery With Battery With Standard Batteries OFES 850 VA 36 kg 49 kg OFES 1 15 kVA 40 kg 64 kg OFES 1 4 kVA 47 kg 70 kg OFES 1 8 kVA 49 kg 72 kg OFES 2 1 kVA 54 kg 77 kg OFES 3 1 kVA 64 kg 92 kg OFER 1 8 kVA 51 kg 98 kg OFER 2 1 kVA 56 kg 103 kg OFER 3 1 kVA 66 kg 111 kg OFER 4 3 kVA 118 kg 113 4 kg OFER 7 kVA 158 8 kg 113 4 kg Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality 59 SPECIFICATIONS 60 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality 9 Alarms Troubleshooting When your FERRUPS Rack Mount UPS detects an alarm condition the UPS displays the alarm with the following indications the ALARM indicator on the front panel and the control panel if you have one illuminates sounds an audible alarm displays an alarm message on the control panel if you have NOTE If the control panel does not display the message press CLEAR until you reach the scrolling display When an alarm occurs follow these steps 1 Find out which alarm condition the UPS is detecting f you have a control panel you can read the alarm on the display e f you do not have a control panel listen to the alarm code the UPS sounds the Mors
6. 164201424 Rev 1 19 www eaton com powerquality UPS STARTUP 5 For Plug Receptacle UPSs Plug the equipment to be protected into the UPS output receptacles NOTE For 50 Hz models use the supplied IEC 320 jumper cord to connect your equipment to the UPS output receptacles For Hardwired UPSs Turn the bypass switch to the UPS position 6 Turn on the eguipment that is connected to the UPS If the ALARM indicator illuminates see Alarms on page 61 7 If your FERRUPS Rack Mount UPS is configured to use an external battery cabinet you must program the battery capacity in ampere hour Ah for the total number of battery packs used in the UPS If you purchased one of the FERRUPS Rack Mount battery pack options available from Eaton select the Ah value from Table 1 NOTE A Remote Control Panel part number RCK 0007 PC or terminal is required to communicate with the UPS Before programming the battery Ah enter the user level password following the instructions in Entering Passwords on page 30 change the battery Ah parameter 69 Batt Ah follow these steps Press this key Display shows DISPLAY 6 9 ENTER 69 Batt AH Default PROGRAM 69 Pgm Ah Value from Table 1 69 Pgm ENTER 69 Pgm new value where xxx is the Battery Ah value from Table 1 20 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality UPS STARTUP Table 1 E
7. At any time Press ENTER to display edit next menu item Press PROGRAM to exit menu and save changes Press CLEAR to exit menu without saving changes Menu Item Baud Rate 0 300 1 1200 2 2400 3 4800 4 9600 5 19200 Brightness Display brightness 0 7 Max Beeper Beeper enabled 0 1 Yes Keyclick Keyclick enabled 0 1 Yes Repeat Autorepeat of depressed key 0 1 Yes Connect Send 123DCP at startup 0 1 Yes Figure 9 Remote Control Panel Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality OPERATION Automatic System Test The UPS performs an automatic system test every seven days to test the memory batteries and inverter During the system test the BATTERY POWER and READY indicators flash For the results of the last system test you can display parameter 26 see page 37 Logic Test First the UPS checks its memory If it finds a problem the UPS sounds alarm O Memory Check See page 63 Inverter Test The inverter converts DC battery power into the AC power your eguipment uses During the inverter test the UPS pulses its inverter to see if it delivers the proper amount of current If not the UPS sounds alarm N Check Inverter See page 63 Although it is testing the inverter the UPS is not in Inverter On mode The UPS continues to condition input power and is ready to provide battery power if there is a power
8. Volt Amps Out The total apparent power your equipment is drawing from the UPS This value is based on parameter 2 multiplied by parameter 4 and should be less than or equal to the VA or kVA rating of the UPS See VA Limit parameter 19 06 Batt 0 0 Service ibatt ib Battery Current When the UPS is running on AC input this is the charging current in amperes A When the UPS runs on battery power inverter this is the amount of current in amperes the batteries are supplying to the UPS 07 V Batt 48 51 Service vbatt vb Battery Volts The present battery voltage The UPS sounds an alarm if this value is too low 08 Freq 60 43 Hz Change Not Allowed frequency f In normal operation this is the frequency of power the UPS is receiving from the AC input source If this value falls outside preset limits the UPS goes to battery power When the UPS is running on battery power this is the frequency the UPS is supplying to your equipment 09 RunTime 12m Change Not Allowed runtime rt Estimated Run Time Remaining The amount of time the UPS continues to support your equipment when the UPS is running on battery power The UPS sounds an alarm when this value falls below a preset limit 10 10 Date 06 01 02 None date d System Date The UPS uses this date to record alarms and inverter runs The date must be reset when you restart the UPS after DC power is t
9. enter delay 400 display d Depends Displays the values of one or more parameters see Table 5 on on page 34 parameter Format display parameter or name parameter or name password Example d 1 fullload ol displays the values of parameters 1 16 and 21 extendedhistory xh None Displays the minimum and maximum values of parameters 1 Vac In 2 Vac Out 7 Vdc and 5 VA Out the command then clears the minimum and maximum values see Table 5 on page 34 format f None Displays an 80 character line containing information on the FERRUPS status CheckUPS II and other UPS monitoring software use this data help or he None Shows a list of terminal computer commands history h None Displays the minimum and maximum values of parameter 1 Vac In the command then clears the minimum and maximum values identify Shows Eaton s address and telephone number and the software version inverterlog il None Displays the Inverter Log See Alarm and Inverter Logs on page 64 logs None Displays both the Alarm and Inverter Logs See Alarm and Inverter Logs on page 64 off time time None Shuts down the UPS a given number of seconds The READY indicator flashes until the UPS shuts down and the UPS beeps 5 seconds before shutdown Example OFF 60 shuts down the UPS in 60 seconds off time autostart time None Shuts down the UPS in a given number of seconds see above and a restarts the UPS shortly after
10. ller LIVSFARLIG SP NNING ENDAST AUKTORISERAD SERVICEPERSONAL far utf ra reparationer eller service Det finns inga delar som ANVANDAREN KAN UTFORA SERVICE PA inuti UPS enheten e Denna UPS enhet har en egen energik lla batterier De utgaende kontakterna kan vara str mf rande n r UPS enheten inte r ansluten till en v xelstr mk lla Taaldrig bort n tsladden n r UPS enheten r p slagen Detta tar bort skyddsjordningen fran bade UPS enheten och den anslutna utrustningen Minska risken f r brand eller elektriska st tar genom att installera denna UPS enhet inomhus d r temperatur och luftfuktighet r kontrollerade och d r inga ledande f roreningar f rekommer Omgivande temperatur f r ej verstiga 40 C Anv nd inte utrustningen n ra vatten eller vid h g luftfuktighet max 95 e F r att verensst mma med internationell standard och installationsf reskrifter far inte den totala utrustning som anslutits till uttagen p denna UPS enhet ha l cksstr m som verstiger 1 5 milliampere Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 15 www eaton com powerguality SAFETY WARNINGS VIKTIGT e Batterierna kan inneb ra en risk f r elektrisk st t eller br nnskada fran kortsluten starkstr m lakttag l mpliga f rsiktighets tg rder Service ska utf ras av utbildad servicepersonal med kunskap om batterierna och n dv ndiga f rsiktighets tg rder H ll ej beh rig pers
11. B e OT 40
12. Eaton Corporation an Ohio Corporation company Company LIMITED WARRANTY This limited warranty this Warranty applies only to the original End User the End User of any Eaton 9155 9170 and FERRUPS 4 3 18 kVA Products individually and collectively the Product purchased on or after June 1 2004 and cannot be transferred This Warranty applies even in the event that the Product is initially sold by Company for resale to an End User LIMITED WARRANTY PERIOD The period covered by this Warranty for Product installed and currently located in the fifty 50 United States the District of Columbia and Canada is twenty four 24 months from the date of purchase or thirty 30 months from the date of shipment for parts and ninety 90 days from the date of purchase for labor as further clarified in the following sections WHAT THIS LIMITED WARRANTY COVERS The warrantor warrants that the Product and battery individually and collectively the Warranted Items are free from defects in material and workmanship If in the opinion of Company a Warranted Item is defective and the defect is within the terms of this Warranty Company s sole obligation will be to repair or replace such defective Warranted Item including by providing service parts and labor as applicable at the option of Company and such repair or replacement shall be at either the End User s location Company s site or such other location as determin
13. Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 41 www eaton com powerguality COMMUNICATION Communication Port The communication port cable pins are identified in Figure 10 and the pin functions are described in Table 6 000000000000 69 63 69 69 9 9 099 9 Figure 10 Communication Port Table 6 Communication Port Pin Functions Pin Function Function 2 Transmit Data in 3 Receive Data out Reguest to Send To enable hardware handshaking on these pins call your service 5 Clear to Send representative 6 12V Level 0 01A when the UPS is operating 7 Signal Ground 11 Contact opens when on inverter 12 Contact closes when on These relay contacts are rated at 25 Vac Vdc and 250 mA see Remote inverter Monitoring on page 49 13 Common Inverter Signal Contact 14 12V 0 5A 850 VA 3 1 kVA or 0 3A 4 3 7 kVA Do not use for setting logic levels 18 12V Level 0 01A when UPS is operating 20 AS 400 Option 21 Remote Shutdown 23 Contact closes on alarm These relay contacts are rated at 25 Vac Vdc and 250 mA see Remote 24 Alarm Signal Contact Monitoring on page 49 Pins 23 and 25 change status when the UPS is turned off 25 Contact opens on alarm NOTE Pins 2 5 and 7 for RS 232 communication Pins 11 13 and 23 25 are for remote monitoring and Pin 21 used with 6 or 18 is for r
14. INDEMNITY IN TORT INCLUDING NEGLIGENCE OR STRICT LIABILITY OR OTHERWISE SHALL NOT EXCEED THOSE SET FORTH ABOVE Company shall not be responsible for failure to provide repair or replacement under this Guaranty due to causes beyond Company s reasonable control END USER S OBLIGATIONS In order to receive the benefits of this Guaranty the End User must use the Product in a normal way follow the Product s user s guide and protect against further damage to the Product if there is a covered defect OTHER LIMITATIONS Company s obligations under this Guaranty are expressly conditioned upon receipt by Company of all payments due to it including interest charges if any During such time as Company has not received payment of any amount due to it for the Product in accordance with the contract terms under which the Product is sold Company shall have no obligation under this Guaranty COSTS NOT RELATED TO GUARANTY The End User shall be invoiced for and shall pay for all services not expressly provided for by the terms of this Guaranty including without limitation site calls involving an inspection that determines no corrective maintenance is required Any costs for replacement equipment installation materials freight charges travel expenses or labor of Company representatives outside the terms of this Guaranty will be borne by the End User TO MAKE A CLAIM In the USA call the Customer Reliability Center 7x24 at 800 356 5737 Outside o
15. Product s labels or instructions This Warranty is not valid if the Product s serial numbers have been removed or are illegible Any Warranted Items repaired or replaced pursuant to this Warranty will be warranted for the remaining portion of the original Warranty subject to all the terms thereof Company shall not be responsible for any charges for testing checking removal or installation of Warranted Items COMPANY DOES NOT WARRANT EQUIPMENT MANUFACTURED BY COMPANY IF PERMITTED BY THE APPLICABLE MANUFACTURER COMPANY SHALL PASS THROUGH SUCH MANUFACTURER S WARRANTIES TO END USER COMPANY DOES NOT WARRANT SOFTWARE INCLUDING SOFTWARE EMBEDDED IN PRODUCTS THAT IS NOT CREATED BY COMPANY WITHOUT LIMITING THE FOREGOING COMPANY SPECIFICALLY DOES NOT WARRANT SOFTWARE SUCH AS LINUX THAT WAS CREATED USING AN OPEN SOURCE MODEL OR IS DISTRIBUTED PURSUANT TO AN OPEN SOURCE LICENSE THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY OFFERED BY COMPANY WITH RESPECT TO THE PRODUCTS AND SERVICES AND EXCEPT FOR SUCH FOREGOING WARRANTY COMPANY DISCLAIMS ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY TITLE NON INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE CORRECTION OF NON CONFORMITIES IN THE MANNER AND FOR THE PERIOD OF TIME PROVIDED ABOVE SHALL CONSTITUTE COMPANY S SOLE LIABILITY AND END USER S EXCLUSIVE REMEDY FOR FAILURE OF COMPANY TO MEET ITS WARRANTY OBLIGATIONS WHETHER CLAIMS OF THE E
16. Warranted Item including by providing service parts and labor as applicable at the option of Company PROCEDURES FOR REPAIR OR REPLACEMENT OF WARRANTED ITEMS The Warranted Item will be repaired or replaced at a Company site or such other location as determined by Company If the Warranted Item is to be replaced by Company and the End User supplies a credit card number or purchase order for the value of the replacement Product Company will use commercially reasonable business efforts to ship via standard ground shipment and at no cost to the End User the replacement Warranted Item to the End User within one 1 business day after Company receives notice of the warranty claim In such case the End User must return at Company s expense the defective Warranted Item to Company in the same packaging as the replacement Warranted Item received by the End User or as otherwise instructed by Company If Company does not receive the defective Warranted Item Company will either charge the End User s credit card or send the End User an invoice which the End User agrees to pay for the value of the replacement Product If the Warranted Item is to be replaced by Company but the End User is unwilling or unable to supply a credit card number or purchase order for the value of the replacement Product Company will use commercially reasonable business efforts to ship via standard ground shipment and at no cost to the End User the replacement Warranted I
17. and inverter periodically to ensure reliable operation fact you ll probably find that your FERRUPS Rack Mount system requires less maintenance than any of your other computer peripherals Nevertheless the FERRUPS Rack Mount UPS and optional external battery cabinets do require some attention to assure continued reliable service Eaton recommends that you schedule preventive maintenance checks at least every six months At these checks the service technician should follow Eaton s recommended maintenance schedule which includes the following items e Check operating environment for clean cool dry conditions e Inspect and clean the unit e View and record the alarm and inverter logs e Check the batteries e Check the AC and DC meter functions and recalibrate if necessary e Perform an outage test e Check and record the values of the first 19 parameters while the UPS is online and on battery For more information on preventive maintenance checks contact your service representative Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 53 www eaton com powerquality 54 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality Chapter 8 Specifications Table 10 850 7 kVA Model Specifications Model 850 VA 115kVA 1 4 18kVA 21kVA 331kVA 43kVA 7 kVA 600W 800W 1 KW 1 25 15kW 2 2 kW 3
18. change the charger mode e chargermode off chm f or chargermode disable chm d charger off e chargermode on chm o or chargermode enable chm e charger on e chargermode auto chm a charger enabled if AC input voltage and battery voltage are acceptable clearalarms ca None Clears all active alarms clearhistory ch None Clears the minimum and maximum parameter values shown when you use the extendedhistory or history commands clearpassword cp None Clears the current password commands cm None Displays a list of all valid commands contdisplay cd Depends Continuously displays the parameter that you are currently displaying on You can specify other parameters for the continuous display by parameter entering the name or number of each parameter after the contdisplay password command f you change parameter 39 to Yes this command requires a user level password 46 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality COMMUNICATION Command Short Password Function Form contstatus cs None Continuously displays the Status information see the status command date da None Displays system time and date To set the date enter date month day year delay dl None Delays next command when you enter a number after delay Each unit represents 2 5 milliseconds so delay 1 would cause a 2 5 millisecond delay For a 1 second delay
19. outage The BATTERY POWER indicator flashes during this part of the test Battery Test The UPS also checks its batteries to verify that they can support your eguipment for the minimum specified run time If not the UPS sounds alarm M Check Battery See page 63 The READY indicator flashes during this part of the test Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 33 www eaton com powerguality OPERATION Parameters Table 5 shows the first 26 parameters You can view or reset the parameters using the control panel or a terminal or computer If you plan to view or change parameters from the control panel see Using the Control Panel on page 29 for instructions If you plan to view or change parameters from a terminal or computer that you have connected to the RS 232 port see Entering Commands from a Terminal or Computer on page 46 When you use commands to display or change parameters identify the parameter with either its number or name see Table 5 If you use the name you can enter the entire parameter name or just the short form you can also abbreviate the parameter name as long as your abbreviation includes the letters in the short form Although you do not need a password to view any of the first 26 parameters all of them reguire a password to change see the password column in Table 5 See Entering Passwords on page 30 or Entering Commands from a Terminal or Com
20. the UPS output in 60 seconds if you enter shutdown or alone or the number of seconds you specify after the command The shutdown autostart sda READY indicator flashes until the UPS shuts down If you specify autostart the UPS restarts shortly after power returns shutdown cancel sdc None Cancels a shutdown started with the shutdown command shutup sh None Turns off audible alarm status 5 Shows date time system status present system mode active alarms and the value of various system parameters systemmode _ sm None Typing systemmode alone displays which system mode is now active You use systemmode with a f i or 110 enter one of the modes below systemmode auto sma None Enters the Auto mode This is the normal FERRUPS UPS mode In this mode the UPS provides conditioned AC power to your eguipment if there is a power outage the UPS is ready to switch to battery power systemmode off smf None Enters the Off mode In this mode the UPS is not providing power to your eguipment but you can still use the UPS control panel f you change parameter 39 to Yes this command requires a user level password 48 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality COMMUNICATION Command EI Password Function Form systemmode smi None Enters the Inverter On mode In this mode the UPS is converting DC inverter battery power to AC power for your e
21. ytt ohje sis lt t rkeit ohjeita joita on noudatettava UPS virtal hteen ja akkujen asennuksen ja huollon yhteydess Lue kaikki ohjeet ennen laitteiston k ytt ja s ilyt ohje my hemp tarvetta varten VAARA T m UPS sis lt HENGENVAARALLISIA J NNITTEIT Kaikki korjaukset ja huollot on j tett v VAIN VALTUUTETUN HUOLTOHENKIL N TOIMEKSI UPS ei sis ll MIT N K YTT J N HUOLLETTAVIA OSIA VAROITUS e T m UPS sis lt oman energial hteen akuston Ulostuloliittimiss voi olla j nnite un UPS ei ole liitettyn verkkoj nnitteeseen l poista tai irrota sis ntulojohtoa kun UPS on kytkettyn T m poistaa urvamaadoituksen UPS laitteesta ja siihen liitetyst laitteistosta e V hent ksesi tulipalon ja s hk iskun vaaraa asenna t m UPS sis tiloihin joissa l mp tila ja kosteus on s dett viss ja joissa ei ole virtaa johtavia ep puhtauksia Ymp rist n l mp tila ei saa ylitt 40 C l k yt l hell vett ja v lt osteita tiloja 95 maksimi e Kansainv liset normit ja johdotusm r ykset vaativat ett kaikkien t m n UPS laitteen ulostulokytkent jen yhteinen maavuotovirta ei ylit 1 5 milliampeeria mA e Akut voivat aiheuttaa s hk iskun tai palovammojen vaaran johtuen suuresta oikosulkuvirrasta Noudata kaikkia asianmukaisia varotoimia Laitteen saa huoltaa vain ammattitaitoinen huoltohenkil kunta joka tuntee akut ja niih
22. 0 x 21 25 10 5 x 19 0 850 VA 1 15 kVA 1 4 k VA 1 8 kVA 2 1 kVA 24 8 cm x 40 6 cm x 54 0 cm 26 7 cm x 48 3 cm and 3 1 kVA FER OFER 9 75 x 16 0 x 26 25 10 5 x 19 0 1 8 kVA 2 1 kVA and 3 1 kVA 24 8 cm x 40 6 cm x 66 7 cm 26 7 cm x 48 3 cm FER OFER 19 0 x 16 0 x 26 25 19 25 x 19 0 4 3 KVA and 7 kVA 48 3 cm x 40 6 cm x 66 7 cm 48 9 cm x 48 3 cm RBC 1 and RBC 2 Battery Cabinets 13 5 x 17 0 x 26 5 14 0 x 19 0 34 3 cm x 43 2 cm x 67 3 cm 35 6 cm x 48 3 cm RBC 3 Battery Cabinets 8 3 x 16 25 x 24 25 8 8 x 19 0 21 1 cm x 41 3 cm x 61 6 cm 22 4 cm x 48 3 cm 58 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality Table 16 Weights SPECIFICATIONS 60 Hz Models UPS Weight UPS Weight Battery Cabinet Without Battery With Battery With Standard Batteries FES 850 VA 79 Ib 36 kg 105 Ib 48 kg FES 1 15 kVA 83 Ib 38 kg 135 Ib 62 kg FES 1 4 kVA 98 Ib 45 kg 150 Ib 68 kg FES 1 8 kVA 96 Ib 44 kg 152 Ib 69 kg FES 2 1 kVA 106 Ib 48 kg 162 Ib 74 kg FES 3 1 kVA 128 Ib 58 kg 188 Ib 85 kg FER 1 8 kVA 105 Ib 48 kg 209 Ib 95 kg FER 2 1 kVA 116 Ib 53 kg 220 Ib 100 kg FER 3 1 kVA 138 Ib 63 kg 238 Ib 108 kg FER 4 3 kVA 245 Ib 111 kg 250 Ib 113 4 kg 7 330 Ib 150 kg
23. 2 The German Postal Service was notified that the equipment is being marketed The German Postal Service has the right to retest the equipment and verify compliance Hiermit wird bescheinigt daf die unterbrechungsfreie Stromversorgung QFES 850 VA 1 15 kVA 1 4 1 8 KVA 2 1 kVA and 3 1 k VA QFER 1 8 KVA 2 1 KVA 3 1 k VA 4 3 and 7 KVA in Ubereinstimmung mit den Bestimmungen der Vfg 243 1991 und Vfg 46 1992 funkentst rt ist Der Deutschen Bundespost wurde das Inverkehrbringen dieses Ger tes angezeigt und die Berechtigung zur Uberpriifung der Serie auf Einhaltung der Bestimmung einger umt Eaton reserves the right to change specifications without prior notice Eaton Powerware FERRUPS and CheckUPS are registered trademarks and EnviroCom is a trademark of Eaton Corporation or its subsidiaries and affiliates Microsoft and Windows are registered trademarks of Microsoft Corporation HyperTerminal is a registered trademark of Hilgraeve TeleVideo is a registered trademark of TeleVideo Inc WYSE is a registered trademark of WYSE Technology Inc All other trademarks are property of their respective companies Copyright 1997 2010 Eaton Corporaton Raleigh NC USA All rights reserved No part of this document may be reproduced in any way without the express written approval of Eaton Corporation Table of Contents 1 Introduction 2 Safety Warnings 3 UPS Startup Identifying Your UPS Startup for F
24. 5 Alarm Log Change Not alarmlog A record of the date time duration and A 0319 2127 1215 Allowed al reason for the last 20 alarms see Alarm and Inverter Logs on page 64 26 26 Test Results Change Not testresults This parameter records the results of the See Allowed tr explanation last system test The parameter display includes the time and date of the test and the results of each part of the system test see Automatic System Test on page 33 Additional Parameters The microprocessor in the UPS keeps track of more than 100 parameters Parameters 27 and above are alarm and operation set points calibration factors and other settings You usually do not need access to these parameters for normal operation of the UPS If you need information about the full range of UPS parameters call your service representative to ask for TIP 407 or TIP 503 TIP 407 describes communication from a control panel TIP 503 describes communication through the RS 232 port UPS Shutdown The FERRUPS Rack Mount UPS is designed for many years of round the clock operation Usually you do not need to shut down the UPS even if your equipment is shut down for several days Even when it s not powering your equipment the UPS monitors its internal condition and keeps the Time and Date parameters current The following situations may require a UPS shutdown 1 When you do not expect to use it for an extended period of time When it is being ser
25. ES OFES 850 VA 3 1 kVA or FER OFER 1 8 3 1 UPSs Startup for the FER OFER 4 3 7 UPS 222 52 oce be RR kinds 4 Operation Front Panel Indicators Using the Control Panel Changing Operating Modes Entering Passwords Displaying and Changing Parameters Locking and Unlocking the Control Panel Using the Configuration Menu Automatic System Test Logic Test Inverter Test Battery Test Parameters UPS Shutdown Extended Power Outages 4 2 ie bed dida Adda de S u b SELLES 5 Communication Software Suite CD Communication Port Connecting a Terminal or Computer to the RS 232 Port Entering Commands from a Terminal or Computer Remote Monitoring Remote Shutdown Bypass Switches Control Panel Environmental Monitoring Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality 17 18 21 27 29 29 30 31 31 32 33 33 33 33 34 37 39 4 42 43 46 49 50 51 51 51 TABLE OF CONTENTS Extended uris MITIS use Ia Maltranties o s ete
26. G 68 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality Chapter 10 Warranty Two Year Limited Warranty US and Canada Eaton UPS Models 9120 9125 9130 9135 9140 and FERRUPS up to 3 1 kVA WARRANTOR The warrantor for the limited warranties set forth herein is Eaton Corporation an Ohio Corporation company Company LIMITED WARRANTY This limited warranty this Warranty applies only to the original End User the End User of any Eaton 9120 9125 9130 9135 9140 and FERRUPS up to 3 1 k VA Products individually and collectively the Product purchased on or after June 1 2004 and cannot be transferred This Warranty applies even in the event that the Product is initially sold by Company for resale to an End User LIMITED WARRANTY PERIOD The period covered by this Warranty for Product installed and currently located in the fifty 50 United States the District of Columbia and Canada is twenty four 24 months from the date of purchase or thirty 30 months from the date of shipment WHAT THIS LIMITED WARRANTY COVERS The warrantor warrants that the Product and battery individually and collectively the Warranted Items are free from defects in material and workmanship If in the opinion of Company a Warranted Item is defective and the defect is within the terms of this Warranty Company s sole obligation will be to repair or replace such defective
27. Guide 164201424 Rev 1 www eaton com powerguality SAFETY WARNINGS Sikkerhedsanvisninger VIGTIGE SIKKERHEDSANVISNINGER GEM DISSE ANVISNINGER Denne manual indeholder vigtige instruktioner som skal f lges under installation og vedligeholdelse af UPS en og batterierne L s venligst alle instruktioner inden betjening af udstyret og gem denne manual mhp fremtidige opslag A Denne UPS indeholder LIVSFARLIG HOJSPANDING Alle reparationer og vedligeholdelse bar kun udfgres af en AUTORISERET SERVICETEKNIKER Ingen af UPS ens indvendige dele kan repareres af brugeren ADVARSEL A e Denne UPS indeholder egen energiforsyning batterier Udgangsnetstikkene lede strgm selv nar UPS en ikke er tilsat en AC energikilde e Netledningen ma ikke fjernes og stikket m ikke tr kkes ud mens UPS en er t ndt Dette fjerner sikkerhedsjorden fra UPS en og fra det udstyr der er sat til e Installer denne UPS i et temperatur og fugtighedskontrolleret indend rsmilj frit for ledende forureningsstoffer for at formindske risikoen for brand og elektrisk stad Rumtemperaturen m ikke overstige 40 C UPS en bar ikke betjenes n r vand eller hgj fugtighed maksimalt 95 e overensstemmelse med internationale normer og bestemmelser for el installation m det udstyr der er forbundet til udgangen af denne UPS tilsammen ikke overskride en jordafdelingsspaending p mere end 1 5 milliampere ADVARSEL Batterierne kan give risiko fo
28. Log If the inverter has not run 20 times the display scrolls through the entries the UPS has recorded You can use the number keys as you view this scrolling display Use this key To do this 0 Pause the scrolling and start it again 1 through 9 Go to the next log entry Each entry includes four pieces of information the inverter code the date month day of the inverter run the time in 24 hour time and the duration in hours and minutes For instance one entry might look like this L 0205 0951 0015 In this example L means the the UPS went to inverter because it lost AC input power if the inverter was still running there would be an asterisk after the L 0205 means the inverter ran on February 5 0951 means the inverter ran at 9 51 a m 0015 means the inverter ran for 0 hours and 15 minutes Table 18 Inverter Codes Inverter Code Meaning Explanation T System Test UPS went to inverter to test the batteries B Brownout AC input voltage was too low L Line Loss AC input power was lost M Manual The inverter was started manually F Frequency Input frequency was too high or too low R Reset A system reset was performed Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 65 www eaton com powerquality TROUBLESHOOTING 66 Reading the Alarm Log from a Terminal or Computer To display the Alarm Log on a terminal or computer you can use the alarml
29. Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality TROUBLESHOOTING Audio Alarm Letter What It Means What To Do Code Message J UserTest user is testing the alarm feature To start the user test alarm from the Alarm control panel press CTRL 8 ENTER ENTER Repeat the procedure to turn the alarm off K Transfmr The transformer temperature is too high The UPS may have shut down if so Temp If the temperature reaches a preset contact your service representative If point the UPS shuts down the UPS has not shut down shut down your equipment or bypass the UPS then turn the UPS off and contact your service representative L Check The UPS has detected a charger Contact your service representative Charger problem M The batteries have failed the automatic Contact your service representative Battery systemtest N inverter has failed the automatic Contact your service representative Inverter system test 0 Memory Possible microprocessor problem Shut down your eguipment or bypass the Check UPS turn off the UPS Contact your service representative e Emergency Remote Shutdown feature has been restart the UPS disconnect the signal PwrOff activated at the RS 232 port see to Pin 21 on the RS 232 port If you have a Remote Shutdown on page 50 control panel pu
30. ND USER ARE BASED IN CONTRACT IN TORT INCLUDING NEGLIGENCE OR STRICT LIABILITY OR OTHERWISE LIMITATION OF LIABILITY The remedies of the End User set forth herein are exclusive and are the sole remedies for any failure of Company to comply with its obligations hereunder In no event shall Company be liable in contract in tort including negligence or strict liability or otherwise for damage to property or eguipment other than the Products including loss of profits or revenue loss of use of Products loss of data cost of capital claims of customers of the End User or any special indirect incidental or conseguential damages whatsoever The total cumulative liability of Company hereunder whether the claims are based in contract including indemnity in tort including negligence or strict liability or otherwise shall not exceed the price of the Product on which such liability is based Company shall not be responsible for failure to provide service or parts due to causes beyond Company s reasonable control END USER S OBLIGATIONS In order to receive the benefits of this Warranty the End User must use the Product in a normal way follow the Product s user s guide and protect against further damage to the Product if there is a covered defect 70 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality WARRANTY OTHER LIMITATIONS Company s obligations under this Warranty are expressly c
31. OLTAGES All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY There are NO USER SERVICEABLE PARTS inside the UPS e This UPS contains its own energy source batteries The output receptacles may carry live voltage even when the UPS is not connected to an AC supply Donotremove or unplug the input cord when the UPS is turned on This removes the safety ground from the UPS and the eguipment connected to the UPS e To reduce the risk of fire or electric shock install this UPS in a temperature and humidity controlled indoor environment free of conductive contaminants Ambient temperature must not exceed 40 C 104 F Do not operate near water or excessive humidity 95 max Tocomply with international standards and wiring regulations the total eguipment connected to the output of this UPS must not have an earth leakage current greater than 1 5 milliamperes CAUTION e Batteries can present a risk of electrical shock or burn from high short circuit current Observe proper precautions Servicing should be performed by qualified service personnel knowledgeable of batteries and required precautions Keep unauthorized personnel away from batteries Proper disposal of batteries is required Refer to your local codes for disposal requirements Never dispose of batteries in a fire Batteries may explode when exposed to flame Eaton FERRUPS Rack Mount UPS 850 7 kVA User s
32. Powerware Series Eaton FERRUPS Rack Mount UPS User s Guide E T N Powering Business Worldwide Powerware Series Eaton FERRUPS Rack Mount UPS User s Guide E T N Powering Business Worldwide Class EMC Statements FCC Part 15 NOTE This eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the eguipment is operated in a commercial environment This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be reguired to correct the interference at his own expense ICES 003 This Class Interference Causing Equipment meets all requirements of the Canadian Interference Causing Equipment Regulations ICES 003 Cet appareil num rique de la classe A respecte toutes les exigences du Reglement sur le mat riel brouilleur du Canada For Users in Germany We hereby certify that the uninterruptible power system QFES 850 VA 1 15 KVA 1 4 1 8 kVA 2 1 k VA and 3 1 k VA QFER 1 8 kVA 2 1 KVA 3 1 4 3 KVA and 7 kVA complies with the RFI suppression requirements of Vfg 243 1991 and Vfg 46 199
33. RRANTY COMPANY DISCLAIMS ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY TITLE NON INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE CORRECTION OF NON CONFORMITIES IN THE MANNER AND FOR THE PERIOD OF TIME PROVIDED ABOVE SHALL CONSTITUTE COMPANY S SOLE LIABILITY AND END USER S EXCLUSIVE REMEDY FOR FAILURE OF COMPANY TO MEET ITS WARRANTY OBLIGATIONS WHETHER CLAIMS OF THE END USER ARE BASED IN CONTRACT IN TORT INCLUDING NEGLIGENCE OR STRICT LIABILITY OR OTHERWISE LIMITATION OF LIABILITY The remedies of the End User set forth herein are exclusive and are the sole remedies for any failure of Company to comply with its obligations hereunder In no event shall Company be liable in contract in tort including negligence or strict liability or otherwise for damage to property or equipment other than the Products including loss of profits or revenue loss of use of Products loss of data cost of capital claims of customers of the End User or any special indirect incidental or consequential damages whatsoever The total cumulative liability of Company hereunder whether the claims are based in contract including indemnity in tort including negligence or strict liability or otherwise shall not exceed the price of the Product on which such liability is based Company shall not be responsible for failure to provide service or parts due to causes beyond Company s reasonable control END USER S OBLIGA
34. TIONS In order to receive the benefits of this Warranty the End User must use the Product in a normal way follow the Product s user s guide and protect against further damage to the Product if there is a covered defect OTHER LIMITATIONS Company s obligations under this Warranty are expressly conditioned upon receipt by Company of all payments due to it including interest charges if any During such time as Company has not received payment of any amount due to it for the Product in accordance with the contract terms under which the Product is sold Company shall have no obligation under this Warranty Also during such time the period of this Warranty shall continue to run and the expiration of this Warranty shall not be extended upon payment of any overdue or unpaid amounts COSTS NOT RELATED TO WARRANTY The End User shall be invoiced for and shall pay for all services not expressly provided for by the terms of this Warranty including without limitation site calls involving an inspection that determines no corrective maintenance is required Any costs for replacement equipment installation materials freight charges travel expenses or labor of Company representatives outside the terms of this Warranty will be borne by the End User OBTAINING WARRANTY SERVICE In the USA call the Customer Reliability Center 7x24 at 800 356 5737 Outside of the USA contact your local Eaton product sales or service representative For comments or questi
35. ality UPS STARTUP Startup for FES OFES 850 VA 3 1 kVA or FER OFER 1 8 3 1 k VA UPSs Before starting up the UPS review the rear panel for your UPS model RS 232 Communication D O D O T Port o Alarm Silence Switch 15 m Output ja Receptacles Figure 2 FERRUPS Rack Mount 850 VA 1 4 kVA UPS Rear Panel RS 232 Communication Port am O m e e e Alarm Sil _ _ Uki 69 69 o Ed e Output 2 Receptacles e 0 Figure 3 FERRUPS Rack Mount 1 8 3 1 kVA Rear Panel To start the FES OFES 850 3 1 kVA or FER OFER 1 8 3 1 UPS use the following steps 1 Confirm the eguipment to be protected by the UPS is powered off 2 For Plug Receptacle UPSs Plug the UPS power cord into a power outlet NOTE If the plug does not match your receptacle outlet ask your electrician to install the proper outlet 18 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality UPS STARTUP For 230V Plug Receptacle UPSs Disconnect the power cord from the computer or other eguipment to be protected by the UPS and plug it into the UPS Plug the other end of the power cord into a power outlet NOTE 50 Hz models do not use the 320 jumper cord supplied with the UPS this cord is for plugging the eguipment into the UPS output r
36. anti istruzioni da seguire durante l installazione 6 la manutenzione dell UPS e delle batterie Leggere integralmente le istruzioni prima di utilizzare l apparecchiatura e conservare il presente manuale per futuro riferimento PERICOLO La TENSIONE contenuta in guesto gruppo statico di continuit amp LETALE Tutte le operazioni di riparazione e di manutenzione devono essere effettuate ESCLUSIVAMENTE DA PERSONALE TECNICO AUTORIZZATO All interno del gruppo statico di continuita NON vi sono PARTI RIPARABILI DALL UTENTE AVVERTENZA e Questo gruppo statico di continuit contiene una fonte di energia autonoma le batterie Le prese di uscita possono condurre tensione energizzata quando il gruppo statico di continuita non amp collegato con una fonte di alimentazione a corrente alternata e Non rimuovere n scollegare il cavo di ingresso quando il gruppo statico di continuita acceso poich in tal modo si disattiverebbe il collegamento a terra di sicurezza del gruppo statico di continuita e dell apparecchiatura ad esso collegata e Per ridurre il rischio di incendio o di scossa elettrica installare il gruppo statico di continuita in un ambiente interno a temperatura ed umidita controllata privo di agenti contaminanti conduttivi La temperatura ambiente non deve superare i 40 C Non utilizzare l unit in prossimit di acgua o in presenza di umidita eccessiva 95 max Per conformita con gli standard internazionali
37. at you have the necessary code to unlock the control panel Press this key Display shows CLEAR and ENTER together Keypad Locked Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 31 www eaton com powerguality OPERATION 32 When you lock the control panel it beeps and displays Keypad Locked for approximately two seconds The control panel beeps and shows this display whenever you try to use the keys The front panel indicators continue to show the UPS status and the control panel shows UPS alarms To enable the control panel again Press this key Display shows CLEAR and ENTER together Unlock 8 2 0 4 9 Unlock 82049 ENTER Keypad Unlocked After approximately two seconds the control panel shows the same display it showed before you unlocked it If you enter the wrong unlock number the control panel displays Keypad Locked for two seconds and the control panel remains locked Using the Configuration Menu The control panel includes a Configuration Menu that lets you adjust its baud rate and brightness turn the beeper on or off turn on and off the click you hear when you press keys and control other features The label on the back of your control panel includes more information on this menu see Figure 9 Remote Control Panel RCP Access Instructions for Configuration Menu Simultaneously press CONTROL and PROGRAM to enter RCP Configuration menu
38. ater than 60 dB Table 13 Battery Voltage 850 VA 1 4 kVA models Nominal battery voltage is 12 Vdc Standard battery charger output is variable For 850 VA models the charger output is rated at approximately 4A at low battery and 2A at 13 7 Vdc For 1 15 kVA and 1 4 kVA models the charger output is rated at approximately 8A at low battery and 2A at 13 7 Vdc 1 8 3 1 models Nominal battery voltage is 48 Vdc Standard battery charger output is rated at 4A at 54 8 Vdc 4 3 7 KVA models Nominal battery voltage is 48 Vdc Standard battery charger output is rated at 5A Type Standard batteries are sealed gas recombinant lead acid type especially designed for UPS use NOTE Optional battery chargers at higher current ratings are available Contact Eaton or your local distributor for more information Table 14 Battery Times in Minutes 850 VA 1 15 VA 1 4 VA 1 8 kVA 2 1 kVA 3 1 kVA 4 3 kVA 7kVA Model 600W 800W 1kW 1 25 kW 1 5 kW 2 2 kW 3 kW 5 kW Full Load 11 19 14 31 9 24 7 14 6 26 12 Half Load 28 49 36 73 23 58 18 35 17 61 33 NOTE Times in parenthesis are for FES and OFES models Standard runtimes are shown optional extended runtimes are available Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 57 www eaton com powerguality SPECIFICATIONS Table 15 Dimensions Model Unit H x W x D Front Panel H x W FES OFES 9 75 x 16
39. con humedad excesiva 95 maximo 5 e Para reducir el riesgo de incendio de choque el ctrico instale este SIE en un lugar e cumplir con los est ndares internacionales y las normas de instalaci n la totalidad de los equipos conectados a la salida de este SIE no debe tener una intensidad de p rdida a tierra superior a los 1 5 miliamperios 14 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality SAFETY WARNINGS PRECAUCION e Las bater as pueden constituir un riesgo de descarga el ctrica o quemaduras corriente alta de corto circuito Adopte las precauciones debidas Personal calificado de servicio que conozca de bater as y est al tanto de las precauciones requeridas debe darle servicio al equipo Mantenga al personal no autorizado alejado de las bater as e Es necesario desechar las bater as de un modo adecuado Consulte las normas locales para conocer los requisitos pertinentes e Nunca deseche las bater as en el fuego Las bater as pueden explotar si se las expone la llama S kerhetsf reskrifter VIKTIGA S KERHETSF RESKRIFTER SPARA DESSA FORESKRIFTER Den har anvisningen inneh ller viktiga instruktioner som du ska f lja under installation och underh ll av UPS enheten och batterierna L s alla instruktioner innan du anv nder utrustningen och spara den h r anvisningen f r framtida referens Denna UPS enhet inneh
40. ding output If all three of these conditions are present turn the bypass switch to the LINE position Your eguipment receives direct AC line instead of conditioned power from the UPS Continue to Step 2 If all three of these conditions are not present follow Steps 2 4 before you turn the bypass switch to the LINE position This causes a break in power to your eguipment between shutting down the UPS and turning the bypass switch to the LINE position CAUTION Eguipment can be damaged if you change the switch position when line is applied and the UPS is off or on battery Refer to TIP 410 2 Use the FERRUPS key to turn the UPS ON OFF switch to the OFF position 3 If the UPS is plugged in unplug it For hardwired models turn the AC line disconnect switch to the OFF position Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality OPERATION 4 For battery cabinets with a battery connector on the rear panel unplug the connector between the battery cabinet s and the UPS NOTE sure to this connector before you restart the UPS For battery cabinets without a battery connector turn the DC switch to the OFF position NOTE The DC switch MUST be turned off to ensure that the batteries will not discharge The DC switch is located under the hinged panel on the top of the battery cabinet Remove the bolts that hold the front of the batter
41. dit ambiantes sont co pas d passer 40 C Ne pas utiliser proxim excessivement humide 95 maximum ue l onduleur est sous tension sous peine de du mat riel connect harge lectrique installer l onduleur vu de mat riaux conducteurs o la ntr l es La temp rature ambiante ne doit it d eau ou dans une atmosph re Afin d tre conforme aux normes et r gleme nts internationaux de c blage le courant de fuite la terre de la totalit du mat riel branch sur la sortie de l onduleur ne doit pas d passer 1 5 mA ATTENTION Les batteries peuvent pr senter un risque de choc lectrique ou de br lure provenant d un courant de court circuit haute intensit L entretien doit tre r alis par du personnel les pr cautions n cessaires N autorisez auc batteries Une mise au rebut r glementaire des batteri en vigueur dans votre localit Observez les pr cautions appropri es qualifi connaissant bien les batteries et un personnel non qualifi manipuler les es est obligatoire Consulter les r glements Ne jamais jeter les batteries au feu L exposition aux flammes risque de les faire exploser Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality SAFETY WARNINGS Sicherheitswarnungen WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWAREN Dieses Handbuch enth lt wichtige Anweisungen die Sie w hrend der Installatio
42. djustment or modification of any kind to the Product not authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or Agent or f use of the Product under other than normal operating conditions or in a manner inconsistent with the Product s labels or instructions This Guaranty is not valid a unless the End User returns to Company the Warranty Registration Card within thirty 30 days of purchase or b if the Product s serial numbers have been removed or are illegible Company shall not be responsible for any charges for testing checking removal or installation of any items 74 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality WARRANTY LIMITATION OF LIABILITY THE REMEDIES OF THE END USER SET FORTH HEREIN ARE EXCLUSIVE AND ARE THE SOLE REMEDIES FOR ANY FAILURE OF COMPANY TO COMPLY WITH ITS OBLIGATIONS HEREUNDER EXCEPT AS OTHERWISE PROVIDED FOR IN THIS GUARANTY IN NO EVENT SHALL COMPANY BE LIABLE IN CONTRACT IN TORT INCLUDING NEGLIGENCE OR STRICT LIABILITY OR OTHERWISE FOR DAMAGE TO PROPERTY OR EOUIPMENT OTHER THAN THE PRODUCTS INCLUDING LOSS OF PROFITS OR REVENUE LOSS OF USE OF PRODUCTS LOSS OF DATA COST OF CAPITAL CLAIMS OF CUSTOMERS OF THE END USER OR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEOUENTIAL DAMAGES WHATSOEVER THE TOTAL CUMULATIVE LIABILITY OF COMPANY HEREUNDER WHETHER THE CLAIMS ARE BASED IN CONTRACT INCLUDING
43. e Battery Ah value from Table 2 24 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality UPS STARTUP Table 2 External Battery Pack Ah Values for 4 3 7 kVA UPS Models Battery Pack Battery Ah EBPS4 3R 62 1rd 150 2rd 225 3rd 300 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 25 www eaton com powerguality UPS STARTUP 26 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality 4 Operation This section describes e The UPS front panel indicators e Using the control panel Automatic system testing Parameters e Shutting down the UPS Front Panel Indicators The UPS front panel indicators indicate how the UPS is operating and also alert you of potential power problems Figure 8 shows the UPS front panel indicators Table 3 explains the status of each indicator AC LINE READY CHARGING BATTERY ALARM POWER Figure 8 Front Panel Indicators Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality 27 OPERATION Table 3 Indicator Status Indicator Status Explanation AC LINE On The UPS is getting power from the AC input power source Off The UPS is not getting input power There is a power outage The AC input breaker is tripped The UPS is unpl
44. e Code for the alarm letter Find the alarm in Table 17 and follow the instructions to resolve the problem To silence the alarm 850 3 1 kVA models Turn the Alarm Silence switch on the UPS rear panel to the OFF position 4 3 7 kVA models Press CTRL 5 ENTER ENTER on the control panel After the alarm condition is cleared turn the alarm beep back on using either the switch or the control panel NOTE If you do not turn the alarm beep back on the UPS is not able to sound an alarm code the next time there is an alarm Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 61 www eaton com powerguality TROUBLESHOOTING Table 17 Alarms Audio Alarm Letter What It Means What To Do Code Message A Low Battery The UPS has shut down after running on Wait for AC input power to be restored battery and discharging the batteries When AC input power returns turn on the UPS The CHARGING indicator illuminates as the UPS begins recharging batteries B Near Low battery voltage has reached the The alarm should clear itself when the Battery Near Low Battery setpoint battery charger has charged the batteries enough C High The battery voltage is too high because Contact your service representative Battery problem with the charging circuit or parameter settings D Low The UPS is running on battery power and Shut down your equipm
45. e UPS conditions AC input power and ENTER ENTER provides the conditioned power to your equipment The UPS is ready to Switch to battery power if necessary The AC LINE and READY indicators should be illuminated Line Condition Press CTRL 3 The UPS is conditioning AC input power and providing the conditioned power ENTER ENTER to your equipment but if there is a brownout or power outage the UPS does not switch to battery power Instead the UPS shuts down its output until AC input power is available again The READY indicator is off when the UPS is in this mode Inverter On Press CTRL 4 The UPS converts battery power to AC power for your equipment It does not on battery ENTER ENTER charge the batteries The BATTERY POWER indicator is on The UPS calculates the run time remaining and sounds an alarm when run time starts to get low The READY indicator is off Entering Passwords Before you can change some parameter values you must enter a password You must also enter a password before you enter some of the commands listed on page 46 NOTE Some parameters such as Time Date and Unit ID are not password protected initially If you change parameter 39 to Yes a user level password is required to change these parameters to use CTRL keys or to use some commands See Parameters page 34 and Entering Commands from a Terminal or Computer on page 46 for more information The user l
46. e con le norme in merito al cablaggio tutta l apparecchiatura collegata con l uscita del gruppo statico di continuit non deve avere una corrente di dispersione di terra superiore a 1 5 milliampere ATTENZIONE e Le batterie possono comportare un rischio di scossa elettrica o di ustione in seguito a un elevata corrente di corto circuito Osservare le dovute precauzioni L assistenza deve essere eseguita da personale gualificato esperto di batterie e delle necessarie precauzioni Tenere il personale non autorizzato lontano dalle batterie e Le batterie devono essere smaltite in modo corretto Per i requisiti di smaltimento fare riferimento alle disposizioni locali e Non gettare mai le batterie nel fuoco poich potrebbero esplodere se esposte alle fiamme 10 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality SAFETY WARNINGS Viktig Sikkerhetsinformasion VIKTIGE SIKKERHETSINSTRUKSJONER GJEM DISSE INSTRUKSJONENE Denne h ndboken inneholder viktige instruksjoner som du bgr overholde ved montering og vedlikehold av UPS enheten og batteriene Les alle instruksjoner for utstyret tas i bruk og gjem h ndboken til fremtidig referanse Denne UPS en inneholder LIVSFARLIGE SPENNINGER All reparasjon 00 service m kun utfores av AUTORISERT SERVICEPERSONALE BRUKERE KAN IKKE UTF RE SERVICE NOEN AV DELENE i UPS en e Denne UPS en har en egen energikilde batterier St
47. eceptacles NOTE f the plug does not match your receptacle outlet ask your electrician to install the proper outlet NOTE If you need to order a UPS power cord please call your service representative For Hardwired UPSs Confirm that an electrician has completed and tested the connection to the proper power source and connected your protected eguipment according to the Eaton FERRUPS Rack Mount UPS 850 VA 7 KVA Installation Guide Turn the AC line disconnect switch to the ON position 3 LINE indicator illuminates see Figure 4 AC LINE READY CHARGING BATTERY ALARM POWER Figure 4 Front Panel Indicators 4 Use the FERRUPS key to turn the UPS ON OFF switch to the ON position After a short startup test the READY indicator flashes for a few seconds and then remains illuminated The UPS is ready to supply output power NOTE UPS and external battery cabinets are shipped with the batteries charged However batteries may lose some of the charge during shipping and storage You can use the UPS immediately after unpacking but it may not provide the full rated backup time during a power failure Upon initial startup the UPS may need to operate for 24 hours before the battery is fully charged and full battery backup time is available If the CHARGING indicator is illuminated operate the UPS for 24 hours to fully charge the battery Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide
48. ected eguipment to direct AC input power conveniently when it s time to service the UPS Contact Eaton or your local distributor for recommendations and additional information on the different bypass switches Control panels are available that provide UPS monitoring and operation from a remote location Environmental Monitoring Eaton s EnviroCom monitors office and UPS conditions and phones you when there is a problem EnviroCom II also lets you call the UPS for an update on its status and environment control and communicate with the UPS through a modem Extended Run Times Warranties If you want extended run times contact Eaton or your local distributor for information on adding additional battery capacity or an optional battery charger Besides our standard two year warranty Eaton offers several warranty enhancement plans to meet your service and maintenance needs Contact Eaton or your local distributor for more information Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 51 www eaton com powerguality 5 52 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality 7 9 Maintenance NOTE Technicians must observe important safety precautions while performing these checks The FERRUPS Rack Mount UPS is designed to provide years of trouble free operation Its internal control system checks the batteries
49. ed by Company All Warranted Items returned to Company and all parts replace by Company shall become the property of Company Expenses for any labor to repair the Warranted Item beyond the initial ninety 90 days are the sole responsibility of the End User PROCEDURES FOR REPAIR OR REPLACEMENT OF WARRANTED ITEMS When shipment is required of End User When Company determines that the Warranted Item will be repaired or replaced at a Company site or such other location and the End User must ship to Company the defective Warranted Item the following procedures are required Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 71 www eaton com powerquality WARRANTY If the Warranted Item is to be replaced by Company and the End User supplies a credit card number or purchase order for the value of the replacement Product Company will use commercially reasonable business efforts to ship via standard ground shipment and at no cost to the End User the replacement Warranted Item to the End User within one 1 business day after Company receives notice of the warranty claim In such case the End User must return at Company s expense the defective Warranted Item to Company in the same packaging as the replacement Warranted Item received by the End User or as otherwise instructed by Company If Company does not receive the defective Warranted Item Company will either charge the End User s credit card or send the End User an invo
50. emote shutdown The following sections describe how to take advantage of these features Pin 20 is for option use only 42 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality COMMUNICATION Connecting a Terminal or Computer to the RS 232 Port CAUTION Do not make connections to the RS 232 communication port if the UPS is connected to a positive ground battery system The RS 232 ground must be isolated or equipment damage will result For help contact your service representative If you are connecting a terminal to the RS 232 port the terminal must be capable of serial communication If you are connecting a computer the computer must be running terminal emulation software such as HyperTerminal Most modem software packages can emulate a terminal if you do not have a terminal emulation program please contact your service representative for more information 1 To connect the FERRUPS Rack Mount UPS DB 25S female RS 232 port to your terminal or computer you need a cable designed specifically for this purpose see Figure 11 and Figure 12 Eaton offers cables for computers or terminals using 25 pin or 9 pin serial ports call your service representative to order one of these cables If you would like to build your own cable follow these requirements e Use a high quality shielded cable Do not use a standard 25 conductor straight through cable only include s
51. ent and turn off Runtime the battery run time remaining is low the UPS to conserve battery power When AC input power returns turn the UPS on again E Low AC The output voltage is below a The UPS shuts down Shut down your Output preprogrammed setpoint eguipment or bypass the UPS and turn the UPS switch off Contact your service representative F High AC The output voltage is higher than the Contact your service representative Output alarm setting G Output Power reguirements exceed UPS Turn off and unplug the UPS Remove Overload capacity check the UPS VA rating or some of the eguipment from the UPS the load is defective Restart the UPS If the overload condition persists 125 for 10 minutes the UPS automatically shuts down H eeee Ambient The temperature inside the UPS is too If the UPS has shut down contact your Temp high If the temperature reaches a preset service representative If not shut down point the UPS shuts down the protected equipment and the UPS correct the cause of the high temperature if possible and turn the UPS on again If the problem persists contact your service representative Hi The inverter temperature is too high If If the UPS has shut down contact your Heatsink the temperature reaches a preset point service representative If not shut down Temp the UPS shuts down your eguipment or bypass the UPS turn the UPS off Contact your service representative 62 Eaton FERRUPS Rack
52. erroresonant technology delivers bulletproof power protection against spikes sags surges noise and lightning This UPS represents a breakthrough in the design of advanced online UPSs Providing outstanding performance and reliability the FERRUPS Rack Mount s unique benefits include the following Active voltage regulation converts power from almost any AC source into computer grade power Eliminates harmful harmonic currents from entering a building s wiring where they can disrupt computer operations Enhanced diagnostics initiates automatic startup and scheduled tests on the logic board battery and other critical systems Provides regulated output voltage without drawing power from batteries keeping the batteries fully charged from unexpected blackouts Complete offering of power management software included to ensure data integrity Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 1 www eaton com powerguality INTRODUCTION 2 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality 2 Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions that you should follow during installation and maintenance of the UPS and batteries Please read all instructions before operating the eguipment and save this manual for future reference This UPS contains LETHAL V
53. evel password is 377 lf you need a password for a higher level call your service representative To enter the user level password follow these steps Press this key Display shows CLEAR FERRUPS PROGRAM Password 3 7 7 Password 377 ENTER Level User To clear the password press CLEAR until Password Cleared appears on the control panel display 30 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality OPERATION Displaying and Changing Parameters The names of the first 11 parameters appear in green on the top of the number keys To display a parameter press DISPLAY the parameter number and ENTER For example to display parameter 0 Time follow these steps Press this key Display shows DISPLAY Display 0 Display 0 ENTER 00 Time 07 04 08 To change a parameter display it first Then press PROGRAMI enter the new value for the parameter and press ENTER For example to change parameter O Time follow these steps Press this key Display shows DISPLAY 0 ENTER 00 Time 07 04 08 PROGRAM 00 Pgm 9 3 0 00 Pgm 930 ENTER 00 Time 09 30 00 Locking and Unlocking the Control Panel You may need to lock the control panel if you want to limit its use When disabled the control panel does not respond to the key functions until it is enabled again To disable the panel press the keys shown in the following example verify th
54. f the USA contact your local Eaton product sales or service representative For comments or questions about this Load Protection Guaranty write to the Customer Quality Representative 3301 Spring Forest Road Raleigh North Carolina 27616 USA Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 75 www eaton com powerquality WARRANTY 76 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality Alarm Code Summary See Troubleshooting on page 61 for more information A Low Battery K Hi Transfmr Temp B Near Low Battery L Check Charger C e High Battery M Check Battery D Low Runtime N Check Inverter E Low AC Output 0 Memory Check F eee High AC Output e Emergency PwrOff Output Overload 0 HiPFM Res Temp H Hi Ambient Temp R e_e Probe Missing Hi Heatsink Temp S High AC Input J User Test Alarm T Call Service 164201424 1
55. ical Code Article 250 5d with output neutral bonded to ground There is no direct connection between input and output and less than 2 pF of effective input to output capacitance 56 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality SPECIFICATIONS Table 12 Environmental and Safety Operating Temperature 0 C to 40 C 32 F to 104 F Storage Temperature UPS with batteries 720 to 40 C 74 to 104 F UPS without batteries 720 to 60 C 74 to 140 F Relative Humidity 0 95 noncondensing Operating Altitude Up to 3 000 meters above sea level 10 000 ft The maximum operating ambient temperature decreases 1 C per 300m above sea level 2 F per 1000 ft above sea level Ventilation The air around the UPS must be clean and free of dust corrosive chemicals and other contaminants The FERRUPS Rack Mount UPS uses internal fans to circulate the air for cooling The air must be free to circulate around the UPS and battery cabinet s Do not operate the UPS in a sealed room or container Lightning and Surge The FERRUPS Rack Mount UPS provides 2000 to 1 spike attenuation Tested using Protection lightning standard per ANSI IEEE C62 41 Category A 6000V spike and 200A and Category B 6000V spike and 3000A test and ANSI IEEE C62 45 test procedures Noise Rejection Common mode Greater than 120 dB with output neutral bonded to ground Transverse Normal mode Gre
56. ice which the End User agrees to pay for the value of the replacement Product If the Warranted Item is to be replaced by Company but the End User is unwilling or unable to supply a credit card number or purchase order for the value of the replacement Product Company will use commercially reasonable business efforts to ship via standard ground shipment and at no cost to the End User the replacement Warranted Item to the End User within one 1 business day after Company receives the defective Product from the End User In any case Company will provide shipping instructions and will pay its designated carrier for all shipping charges for return of defective equipment and replacement of Warranted Items Any returned Warranted Item or parts that are replaced may be new or reconditioned All Warranted Items returned to Company and all parts replaced by Company shall become the property of Company WHAT THIS LIMITED WARRANTY DOES NOT COVER This Warranty does not cover any defects or damages caused by a failure to properly store the Product before installation including the charge of batteries no later than the date indicated on the packaging b shipping and delivery of the Product if shipping is FOB Factory c neglect accident abuse misuse misapplication or incorrect installation d repair or alteration not authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or Agent e improper
57. ikkontaktene kan v re str mf rende selv om UPS en ikke er tilsluttet en vekselstramforsyning e Strgmforsyningskabelen m ikke fjernes eller trekkes ut n r UPS en er p slik at ikke sikkerhetsjordingen fjernes fra UPS en og det utstyret som er forbundet med den e For redusere fare for brann eller elektriske st t b r denne UPS en installeres i et innendgrs miljg med kontrollert temperatur og luftfuktighet som er fritt for ledende forurensende stoffer Romtemperaturen m ikke overskride 40 Den m ikke brukes i n rheten av vann eller ved meget hay luftfuktighet 95 maks Alt utstyr som er forbundet med utgangen av denne UPS en m ikke ha en sterkere total lekkasjestram enn 1 5 milliampere for vaere i overensstemmelse med internasjonale standarder og forkablingsbestemmelser FORSIKTIG e Batterier kan utgj re en fare for elektrisk st t eller branns r pga h y kortsluttingsstram Treff passende forholdsregler Service b r utf res av kvalifisert servicepersonale med kjennskap til batterier og n dvendige forholdsregler Hold uautorisert personale borte fra batteriene e Batterier m fjernes p korrekt m te Se lokale forskrifter vedr rende krav om fjerning av batterier e Kast aldri batterier i flammer da de kan eksplodere hvis de utsettes for pen ild Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 11 www eaton com powerquality SAFETY WARNINGS Reg
58. in liittyv t varotoimet l p st valtuuttamatonta henkil st l helle akkuja e Akusto t ytyy h vitt s d sten mukaisella tavalla Noudata paikallisia m r yksi e l koskaan heit akkuja tuleen Ne voivat r j ht 6 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality Consignes de s curit SAFETY WARNINGS CONSIGNES DE SECURITE IMPORTANTES CONSERVER CES INSTRUCTIONS Ce manuel comporte des instructions importantes que vous tes invit suivre lors de toute proc dure d installation et de maintenance des batteries et de l onduleur Veuillez consulter enti rement ces instructions avant de faire fonctionner l quipement et conserver ce manuel afin de pouvoir vous y reporter ult rieurement A Cet onduleur contient des TENSIONS MORTELLES Toute op ration d entretien et de r paration doit tre EXCLUSIVEMENT CONFIEE A UN PERSONNEL QUALIFIE AGREE AUCUNE PI CE REPARABLE PAR L UTILISATEUR ne se trouve dans l onduleur AVERTISSEMENT Cet onduleur renferme sa propre source d 6n ergie batteries Les prises de sortie peuvent tre sous tension m me lorsque l onduleur n est pas branch sur le secteur Ne pas retirer le cordon d alimentation lorsq supprimer la mise la terre de l onduleur et Pour r duire les risques d incendie et de d c uniquement l int rieur dans un lieu d pou temp rature et l humi
59. is key Display shows DISPLAY Display 2115 1 25 ENTER 25 Alarm Log The display scrolls through the 20 most recent entries in the Alarm Log If you have not had 20 alarm conditions the display scrolls through the entries FERRUPS Rack Mount has recorded You can use the number keys as you view this scrolling display Use this key To do this 0 Pause the scrolling and start it again 1 through 9 Go to the next log entry Each log entry consists of four pieces of information the alarm code the date month day of the alarm the time in 24 hour time and the duration in hours and minutes For instance one entry might look like this B 0205 1017 0005 In this example means the alarm was Near Low Battery see Table 17 on page 62 if alarm B was active there would be an asterisk after 0205 means the alarm occurred on February 5 2 5 1017 means the alarm occurred at 10 17 a m 0005 means the alarm condition lasted for O hours and 5 minutes 64 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality TROUBLESHOOTING Reading the Inverter Log from a Control Panel The Inverter Log is parameter 24 To display the Inverter Log follow these steps Press this key Display shows DISPLAY Display 2 4 Display 24 ENTER 24 Inverter Log The display scrolls through the 20 most recent entries in the Inverter
60. it which is adjustable from 0 01 Hz to 3 00 Hz Inverter turns on if line freguency exceeds the selected limit On inverter 60 Hz FER or 50 Hz OFER 0 03 Hz Regulation 3 load regulation under any line load or battery condition to within 8 3 and 5 of nominal Voltage Waveform Sine wave lt 5 THD atrated linear loads computer grade power Overload Capability Online nominal Vac in 150 surge and 125 for 10 minutes On inverter nominal Vdc in 150 surge and 110 for 10 minutes Overload operation is not thermally limited The FERRUPS Rack Mount UPS microprocessor continuously monitors output VA and sounds an alarm before loss of output voltage regulation occurs DC Input Protection DC fuse and battery charger fuse Output Protection The ferroresonant transformer inherently limits current and provides overload protection The FERRUPS Rack Mount UPS has high AC and low AC output voltage alarms as well as an overload alarm If the AC output voltage falls below the low AC output voltage alarm setpoint the UPS sounds an alarm after 5 seconds If the AC output voltage falls below the low AC output shutdown setpoint the UPS sounds an alarm and shuts down Some models have output receptacles protected by fuses or circuit breakers Isolation Including Output Neutral to Ground Bonding The FERRUPS Rack Mount UPS provides a true separately derived power source as defined by National Electr
61. kW 5 kW AC Input Voltage 60 Hz 120V 120V 120V 1202 208 240V 50 Hz 220 230 240V 220 230 240V 220 230 240V 220 230 240V AC Input Current Standard Charger FES FER 120 Vac 6 6A 8 5A 11A 14A 16A 23A 32A 51A 208 Vac 3 7A 5A 6A 9 2A 11A 14A 18A 30A 240 Vac 3 2A 4 2A 5 3A 8 2 92 12 16 26 OFES OFER 220 Vac 44 4 9 5 7A 7 9A 8 24 13A 19A 27 230 42 4 6A 5 4A 7 5A 7 8A 12A 18A 26A 240 Vac 4 0A 4 4A 5 2A 7 2A 7 4A 12A 17A 24A Recommended AC Input Service 10A 15A 15A 20A 20A 30A 40A 70A 60 Hz with 120 Vac Output Voltage and Maximum Output Current3 120 Vac JA 9 3A 11 15 17 26 34A 58A 208 Vac 20A 34A 220 Vac 3 8A 5A 6 4A 79 9 3A 14 19 31A 230 Vac 3 6A 4 8 6 2A 7 6 8 9A 13A 18A 30A 240 Vac 3 5A 5 9A 7 3A 8 6A 13A 17A 29A Efficiency on AC Line 85 88 88 90 90 91 90 90 On Line BTU hour 361 372 465 474 568 742 1138 1896 kW hour 0 106 0 109 0 136 0 139 0 166 0 217 0 333 0 556 Audible Noise dB 48 50 50 50 50 51 50 52 Other voltages available Contact Eaton or your local distributor 2120 Vac is optional for FER 4 3 kVA and FER 7 kVA models 3At 0 7 leading power factor Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality 55 SPECIFICATIONS Table 11 Electrical Input and Output Nominal Freguency Online 60 Hz FER or 50 Hz OFER Output freguency tracks input line freguency up to lim
62. m oferecer risco de choque el trico ou queimadura ocasionados por alta tens o com possibilidade de curto circuito Tome as precauc es adeguadas manutenc o deve ser realizada por pessoal qualificado com conhecimento sobre baterias e ciente das precau es exigidas Mantenha o pessoal n o autorizado afastado das baterias e Siga as instru es apropriadas ao desfazer se das baterias Consulte os c digos do local para maiores informa es sobre os regulamentos de descarte de produtos e Nunca jogue as baterias no fogo porque h risco de explos o 12 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality SAFETY WARNINGS A
63. n on UPS commands Table 8 Keystroke Commands Action Key Seguence Delete last character typed BACKSPACE or CTRL H Delete line CTRL X Pause displays that take more than one screen CTRL S Resume scrolling Turn Pause off CTRL Q Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 45 www eaton com powerguality COMMUNICATION Entering Commands from a Terminal or Computer To monitor or control the FERRUPS Rack Mount UPS from a terminal or computer simply type one of the commands and press ENTER see Table 9 Use the following command syntax type the command in uppercase or lowercase e use the entire command or the short form you can also abbreviate the command as long as you include the letters in the short form useasemicolon to separate more than one command on a line Table 9 Commands Command Password Function Form alarmshelp ah None Shows a list of all possible alarm messages the audio code and letter for each alarm and whether the alarm is active alarmlog al None Displays Alarm Log See Alarm and Inverter Logs on page 64 alarmtest at None Allows you to test the alarm function Alarmtest sounds the User Test alarm J See page 63 alarmtest cancel atc None Turns the User Test alarm off chargermode chm None Shows the UPS battery charger mode By entering a mode after the chargermode command you can
64. n und Wartung des USV Unterbrechungsfreies Stromversorgungssystem und der Batterien befolgen miissen Bitte lesen Sie alle Anweisungen des Handbuches bevor sie mit dem Ger t arbeiten Bewaren Sie das Handbuch zum Nachlesen auf Die USV f hrt lebensgef hrliche Spannungen Alle Reparatur und Wartungsarbeiten sollten nur von Kundendienstfachleuten durchgef hrt werden Die USV enth lt keine vom Benutzer zu wartenden Komponenten ACHTUNG Diese USV ist mit einer eigenen Energiequelle Batterie ausgestattet An den Ausgangssteckdosen kann auch dann Spannung anliegen wenn die USV nicht an einer Wechselspannungsquelle angeschlossen ist e Das Eingangskabel nicht entfernen oder abziehen w hrend die USV eingeschaltet ist weil hierdurch die Sicherheitserdung von der USV und den daran angeschlossenen Ger ten entfernt wird Um die Brand oder Elektroschockgefahr zu verringern diese USV nur in Geb uden mit kontrollierter Temperatur und Luftfeuchtigkeit installieren in denen keine leitenden Schmutzstoffen vorhanden sind Die Umgebungstemperatur darf 40 C nicht bersteigen Die USV nicht in der von Wasser oder in extrem hoher Luftfeuchtigkeit max 95 96 betreiben e Um internationale Normen und Verdrahtungsvorschriften zu erf llen d rfen die an den Ausgang dieser USV angeschlossenen Ger te zusammen einen Erdschlu amp strom von insgesamt 1 5 Milliampere nicht berschreiten VORSICHT Batterien k nnen das Ri
65. og or logs command see Entering Commands from a Terminal or Computer page 46 These commands display up to 20 log entries in a table For example the log might look like this table Active EventDate EventTime Duration Code Event No 08 25 1993 11 25 32 00 00 45 J User Test Alarm No 08 24 1993 12 13 18 00 01 08 A Low Battery No 08 24 1993 12 05 07 00 08 11 B Near Low Battery The table shows whether the alarm is active now Active the date and time of each alarm how long it lasted Duration and what caused the alarm Code Event You can also display parameter 25 to view the Alarm Log this display is the same as the control panel display Reading the Inverter Log from a Terminal or Computer To display the Inverter Log on a terminal or computer you can use the inverterlog or logs command see Entering Commands from a Terminal or Computer on page 46 These commands display up to 20 log entries in a table For example the log might look like this Active EventDate EventTime Duration Code Event No 08 25 1993 11 25 32 00 00 45 M Manual turnon No 08 24 1993 12 13 18 00 01 08 L Line fault The table shows whether the UPS is running on inverter battery power now Active the date and time that the UPS ran on battery power the length of time the UPS ran on battery power Duration and the reason Code Event You can also display parameter 24 to view the Inverter Log this display is the same as the control panel di
66. onal borta fr n batterierna e Batterierna m ste avyttras enligt anvisningarna i lokal lagstiftning e Anv nda batterier f r aldrig br nnas upp De kan explodera 16 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality Chapter 3 UPS Startup This section provides step by step instructions for starting the Eaton FERRUPS Rack Mount UPS Follow these procedures closely to avoid potential damage to your eguipment or the UPS and to protect yourself and others from hazardous operating conditions Identifying Your UPS NOTE Before starting up the UPS verify that it has been installed according to the Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA Installation Guide FERRUPS Rack Mount UPSs come in different sizes see Figure 1 Identify your UPS model and continue to the appropriate startup section 4 3 7 kVA Models See page 21 POWER 850 VA 3 1 kVA Models See page 18 ACUNE READY CHARGNG BATTERY ALARM 000 U ON na d Con ESE ES En AGLINE READY CHARGING ALARM POWER E G FERRUPS Figure 1 Identifying the FERRUPS Rack Mount UPS Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 17 www eaton com powergu
67. onditioned upon receipt by Company of all payments due to it including interest charges if any During such time as Company has not received payment of any amount due to it for the Product in accordance with the contract terms under which the Product is sold Company shall have no obligation under this Warranty Also during such time the period of this Warranty shall continue to run and the expiration of this Warranty shall not be extended upon payment of any overdue or unpaid amounts COSTS NOT RELATED TO WARRANTY The End User shall be invoiced for and shall pay for all services not expressly provided for by the terms of this Warranty including without limitation site calls involving an inspection that determines no corrective maintenance is required Any costs for replacement equipment installation materials freight charges travel expenses or labor of Company representatives outside the terms of this Warranty will be borne by the End User OBTAINING WARRANTY SERVICE In the USA call the Customer Reliability Center 7x24 at 800 356 5737 Outside of the USA contact your local Eaton product sales or service representative For comments or questions about this Warranty write to the Customer Quality Representative 3301 Spring Forest Road Raleigh North Carolina 27616 USA Two Year Limited Warranty US and Canada Eaton UPS Models 9155 9170 and FERRUPSe 4 3 18 kVA WARRANTOR The warrantor for the limited warranties set forth herein is
68. ons about this Warranty write to the Customer Quality Representative 3301 Spring Forest Road Raleigh North Carolina 27616 USA Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 73 www eaton com powerquality WARRANTY Load Protection Guarantee US and Canada Eaton UPS Models 3105 5110 5115 5125 5130 9120 9125 9130 9135 9140 9150 9155 9170 and FERRUPS GUARANTOR The Guarantor for the load protection guaranty set forth herein is Eaton Corporation an Ohio Corporation company LIMITED GUARANTY This load protection guaranty this Guaranty applies only to the original End User the End User of any Eaton 3105 5110 5115 5125 5130 9120 9125 9130 9135 9140 9150 9155 9170 and FERRUPS Products individually and collectively the Product and cannot be transferred This Guaranty applies even in the event that the Product is initially sold by Company for resale to an End User WHAT THIS GUARANTY COVERS For the lifetime of the Product Guarantor promises to repair or replace at Guarantor s option the eguipment valued up to the limits shown below that is damaged by an AC power line surge spike or other transient when properly connected to Guarantor s uninterruptible power system UPS Reimbursement for or restoration of data loss excluded This Guaranty applies only if all of the following circumstances arise 1 The UPS is plugged into properl
69. or computer should be set to 1200 baud 8 bits parity 1 stop bit and full duplex The terminal or terminal emulation software should also be set to full duplex If you are using a terminal note that the FERRUPS Rack Mount UPS supports the TeleVideo 900 series ADM3A and WYSE 50 emulation Table 7 shows the standard settings at the UPS DB 25S port and the settings that can be adjusted Call your service representative if you need to adjust any of the settings 44 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality COMMUNICATION Table 7 DB 25 Port Settings Specification Standard Setting Adjustable to Connector 25 pin D female wired as DCE Format ASCII 8 bits 1 stop bit Standard setting or Most significant bit set to 0 7 8 bits 1 2 stop Baud Rate 1200 50 38400 Parity None Odd Even or None Duplex Full Full or Half 4 Turn your terminal on or run your terminal emulation software Then press ENTER on your keyboard a prompt appears on the screen The prompt varies depending on your current password level gt Normal prompt User gt User level password has been entered 5 Press ENTER on your keyboard a few times to verify that the UPS responds 6 Tocontrol or monitor the UPS simply type the desired command and press ENTER Table 8 shows what keystrokes to use as you type commands or view displays See Table 9 for more informatio
70. power returns off cancel oc None Cancels timed shutdown f you change parameter 39 to Yes this command requires a user level password Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 47 www eaton com powerquality COMMUNICATION Short Command Password Function Form parameters p Depends Shows a list of system parameters See Parameters on page 34 You on can also display a range of parameters by entering the starting and parameter ending parameter number or name after the command password Example Parameters 1 10 displays parameters 1 through 10 paramkeywords pk Depends Displays all parameters and their keywords the names you can use on with commands You can also display a range of parameters by parameter entering the numbers or names of the starting and ending parameters password password pw None Allows you to enter the user level password Typing password alone clears the current password Example password 377 enters the user level password program pr Depends Lets you set the value of any parameter You must enter the appropriate on password before you reset the value See the Password command parameter above password Format PR parameter or name newvalue Example PR 0 815 resets the time parameter 0 to 8 15 a m remote rm None Configures the RS 232 port so the connected terminal works like a control panel shutdown sd None Shuts down
71. puter on page 46 for password information factory Only gualified technicians using the proper metering eguipment should change other parameters calibration may cause the FERRUPS Rack Mount UPS to malfunction Call your service representative before you attempt to change any parameters except 0 10 NOTE All changeable parameters except 0 Time 10 Date and 15 Unit ID are set at the and 15 Table 5 Parameters RUE Sample Display Password EI Explanation Number Short Form 0 00 Time 07 04 00 None time System Time The UPS uses this time to t record alarms and inverter runs When the DC power has been off and you restart the UPS the time shown is the last recorded time before shutdown Reset time when DC power has been off 1 01 V In 120 7 Service acvoltsin The input voltage the UPS is receiving vi When this value drops below the brownout voltage the UPS switches to inverter 2 02 V Out 120 7 Service acvoltsout The voltage the UPS is providing to your vo equipment 34 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality OPERATION Parameter Number Sample Display Password Parameter Name Short Form Explanation 3 03 Reserved Reserved 4 04 Out 6 2 Service acampsiout 0 The current your eguipment is drawing from the UPS 05 VA Out 748 Change Not Allowed vaout va
72. quipment systemmode sm None Enters the Line Condition mode In this mode the UPS provides linecondition conditioned AC power to your eguipment but it does not switch to battery power if there is a power outage Instead the UPS sounds a Low AC Out alarm systemtest stst None Starts a system test of the logic inverter and battery time t None Shows the current UPS time To set the time enter hour minutes after the command unshutup Turns audible alarm back on f you change parameter 39 to Yes this command requires a user level password Remote Monitoring Alarm Signal Contacts These are relay contacts rated at 25 Vac Vdc and 250 mA that change status on any alarm condition or when the UPS is turned off Contacts that close on an alarm are available between Pins 23 and 24 Contacts that open on an alarm are available between Pins 24 and 25 Inverter On Signal Contacts These are relay contacts rated at 25 Vac Vdc and 250 mA that change status when the inverter turns on Contacts that close on inverter operation are available between Pins 12 and 13 Contacts that open on inverter operation are available between Pins 11 and 13 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 49 www eaton com powerguality COMMUNICATION Remote Shutdown The FERRUPS Rack Mount UPS can be connected to a remote shutdown switch to shut off output from the UPS to your protected eguipmen
73. r elektrisk stod eller brands r for rsaget af hgj kortslutningsstram Overhold gaeldende forsigtighedsregler Servicering skal udfgres af kvalificeret servicepersonale med kendskab til batterier og gaeldende forsigtighedsregler Hold uautoriseret personale v k fra batterierne e Korrekt bortskaffelse af batterier er p kr vet Overhold g ldende lokale regler for bortskaffelsesprocedurer e Skaf dig aldrig af med batterierne ved at br nde dem Batterierne kan eksplodere ved aben ild 4 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality SAFETY WARNINGS Belangrijke Veiligheidsinstructies BELANGRIJKE VEILIGHEIDSINSTRUCTIES BEWAAR DEZE INSTRUCTIES Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en het onderhoud van de UPS en de accu s Lees alle instructies voordat u de apparatuur in bedrijf neemt en bewaar deze handleiding als naslagwerk A Deze UPS bevat LEVENSGEVAARLIJKE ELEKTRISCHE SPANNING Alle reparaties en onderhoud dienen UITSLUITEND DOOR ERKEND SERVICEPERSONEEL te worden uitgevoerd Er bevinden zich GEEN ONDERDELEN in de UPS die DOOR DE GEBRUIKER kunnen worden GEREPAREERD e Deze UPS bevat zijn eigen energiebron batterijen De uitgangsaansluitingen kunnen onder spanning staan wanneer de UPS niet op een wisselstroom voeding is aangesloten e Verwijder de ingangsnoer niet of haal de stekker van de ingang
74. s After a few seconds the UPS switches from battery power to AC input power The BATTERY POWER indicator turns off Now turn the UPS bypass switch mounted nearby to the UPS position UPS UPS AC LINE BYPASS SWITCH DISCONNECT SWITCH Figure 7 AC Line Disconnect Switch NOTE UPS and external battery cabinets are shipped with the batteries charged However batteries may lose some of the charge during shipping and storage You can use the UPS immediately after unpacking but it may not provide the full rated backup time during a power failure Upon initial startup the UPS may need to operate for 24 hours before the battery is fully charged and full battery backup time is available If the CHARGING indicator is illuminated operate the UPS for 24 hours to fully charge the battery 6 For Plug Receptacle UPSs Plug the equipment you want to protect into the UPS receptacles and turn on the eguipment If the ALARM indicator illuminates see Alarms on page 61 For Hardwired UPSs Turn on the equipment connected to the UPS If the ALARM indicator illuminates see Alarms on page 61 7 Set the time and date using the control panel NOTE The correct time and date for is needed for the UPS alarm and inverter logs Reset the time and date whenever the UPS has been shut down Time is parameter 0 see Parameters on page 34 for more information To set the time in 24 hour format follow these steps Press
75. s Sita E 7 Maintenance susana yeu 5046 20 526 0014 6 3 Bo Specifications c i 9 JI ATIS GER y ao Alarm and Inverter u Meran Reading the Alarm Log from a Control Panel Reading the Inverter Log from a Control Panel LL Reading the Alarm Log from a Terminal or Computer Reading the Inverter Log from a Terminal or Computer Service and SUPPOrtia maata vand ue an held x bie Pi su h piuhan v 10 Warranty ars aska crie j kv Ra nika ed hd dire Two Year Limited Warranty US and Two Year Limited Warranty US and anada Load Protection Guarantee US and anadal ii Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality Chapter 1 Introduction The Eatone FERRUPSe Rack Mount uninterruptible power system UPS series provides unmatched reliability in configurable power protection for computers and telecommunications eguipment Patented f
76. siko eines elektrischen Schlags bergen oder durch hohen Kurzschlussstrom in Brand geraten Die richtigen VorsichtsmaRnahmen beachten Die Wartung muss von qualifiziertem Wartungspersonal durchgef hrt werden das im Umgang mit Batterien ge bt ist und ber gute Kenntnisse der erforderlichen Vorsichtsma nahmen verf gt Nicht autorisiertes Personal von Batterien fern halten e Die Batterien m ssen ordnungsgemaR entsorgt werden Hierbei sind die rtlichen Bestimmungen zu beachten Batterien niemals verbrennen da sie explodieren k nnen 8 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality SAFETY WARNINGS 0 1 06 2HMANTIKE2 OAHTIEZ AZOAAEIA2 AYTE2 TIZ OAHTIEZ KINAYNOZ UPS nep exe Oleg ot ntokgv g KOL ot OVVINPNOEIS p ret va yivovtar MONO ATTO EEOYXIOAOTHMENO TIA TH XYNTHPHXH To UPS TIEPIEXEI EZAPTHMA HOY NA EIIIZKEY AXTEI ATTO TO XPHXTH NPOEIAONOIHZHK e To uyKeKptuu vo UPS TI LKI tov nny EV PYELOG 000000060766 Ot pevuatodoteg e ou UNOPEL va XOVV evepy tav TO UPS eiva ovvdedeu vo oc MYT EVOAAGOOOLEVOV AC e By te and mv npilo To Tpododooiac UPS eivat avoryto
77. snoer er niet uit terwijl de UPS aan staat Hierdoor zou de UPS en uw aangesloten apparatuur geen aardebeveiliging meer hebben Teneinde de kans op brand of elektrische schok te verminderen dient deze UPS in een gebouw met temperatuur en vochtigheidregeling te worden geinstalleerd waar geen geleidende verontreinigingen aanwezig zijn De omgevingstemperatuur mag 40 C niet overschrijden Niet gebruiken in de buurt van water of bij zeer hoge vochtigheid max 95 e Om aan de internationale normen en bedradingsvoorschriften te voldoen mag de gehele apparatuur die op de uitgang van deze UPS is aangesloten geen aardlekstroom van meer dan 1 5 milliamp re hebben OPGELET e Batterijen leveren gevaar op voor elektrische schokken en kunnen brandwonden veroorzaken door een grote kortsluitstroom Neem de juiste voorzorgsmaatregelen in acht Het onderhoud moet worden uitgevoerd door bevoegde onderhoudsmonteurs die verstand hebben van accu s en op de hoogte zijn van de vereiste voorzorgsmaatregelen Houd onbevoegden uit de buurt van de accu s e De batterijen moeten op de juiste wijze worden opgeruimd Raadpleeg hiervoor uw plaatselijke voorschriften e Nooit batterijen in het vuur gooien De batterijen kunnen ontploffen a Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality SAFETY WARNINGS Tarkeita Turvaohjeita T RKEIT TURVAOHJEITA SUOMI S ILYT N M OHJEET T m k
78. splay Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality TROUBLESHOOTING Service and Support If you have any questions or problems with the UPS call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for a UPS technical representative In the United States 1 800 356 5737 or 1 608 565 2100 Europe Middle East Africa 44 17 53 608 700 Asia 852 2830 3030 Australia 61 3 9706 5022 Please have the following information ready when you call the Help Desk e Model number e Serial number e Version number if available e Date of failure or problem e Symptoms of failure or problem e Customer return address and contact information If repair is reguired you will be given a Returned Material Authorization RMA Number This number must appear on the outside of the package and on the Bill Of Lading if applicable Use the original packaging or reguest packaging from the Help Desk or distributor Units damaged in shipment as a result of improper packaging are not covered under warranty A replacement or repair unit will be shipped freight prepaid for all warrantied units NOTE For critical applications immediate replacement may be available Call the Help Desk for the dealer or distributor nearest you Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 67 www eaton com powerquality TROUBLESHOOTIN
79. t The shutdown switch must have a set of contacts that can apply the UPS s 12 Vdc on Pin 6 to the UPS s Pin 21 You can use Pin 18 instead of Pin 6 do not use Pin 14 Use a single twisted pair shielded cable to connect the switch to the UPS pins A connection between Pins 6 and 21 or 18 and 21 shuts down UPS output power to the protected equipment When the UPS Remote Shutdown feature has been activated the UPS is in the Off mode and the Emergency Power Off alarm sounds A control panel or a terminal connected to the UPS displays Emergency PwrOff To restart the UPS break the connection between Pins 6 and 21 or between Pins 18 and 21 at the UPS s RS 232 port Then follow the steps for your model in UPS Startup on page 17 Note that the 12V level on Pin 6 or Pin 18 is only available when the UPS is operating You can change the type of signal that the UPS responds to and how guickly it responds You can also set up the UPS to restart automatically when the shutdown signal stops See TIP 503 or contact your service representative for more information 50 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality 6 Bypass Switches Control Panel Options Eaton offers many options for your FERRUPS Rack Mount UPS If you would like more information contact Eaton or your local distributor If your UPS does not have a plug a bypass switch can transfer the prot
80. t the UPS in Auto mode If not turn the UPS ON OFF switch off and then on again 0 HiPFMRes The Power Factor Module s temperature If the UPS has shut down contact your Temp is too high If the temperature reachesa service representative If not shut down preset point the UPS shuts down your eguipment or bypass the UPS then turn the UPS off and contact your service representative R e_e Probe A temperature probe is missing or The UPS may shut down Contact your Missing damaged service representative 5 00 High AC The input voltage is higher than the alarm Contact your service representative Input setting T Call Service UPS has detected a problem that The UPS shuts down Contact your reguires service service representative Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 63 www eaton com powerguality TROUBLESHOOTING Alarm and Inverter Logs Your FERRUPS Rack Mount UPS makes an entry in its logs every time it sounds an alarm or switches to inverter battery power This information can be helpful in diagnosing problems You can view the Alarm and Inverter Logs from either the UPS control panel or a terminal or computer that you have connected to the RS 232 port see Connecting a Terminal or Computer to the RS 232 Port on page 43 Reading the Alarm Log from a Control Panel The Alarm Log is parameter 25 To display the Alarm Log from a control panel follow these steps Press th
81. te control panel as an option refer to TIP 407 to connect the control panel The control panel is attached to the front of the UPS with a 6 ft 1 8m cable providing hand held operation The control panel s READY BATTERY POWER and ALARM indicators work like the READY BATTERY POWER and ALARM indicators on the front of the UPS see Front Panel Indicators on page 27 You can use the control panel to change UPS system modes and display and change parameters You can also lock the control panel and change some of its features If you press the wrong key at any time press CLEAR and then the correct key Changing Operating Modes There are four UPS operating modes e e Auto Line Condition e Inverter On on battery The FERRUPS Rack Mount UPS selects the appropriate operating mode automatically however there may be times when you need to set the operating mode manually from the control panel Notice that names of the operating modes appear in red on the bottom of keys 1 4 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 29 www eaton com powerguality OPERATION Table 4 Operating Modes Operating Mode How to Select It What It Means Off Press CTRL 1 The UPS does not provide power to your equipment but you can still use the ENTER ENTER control panel if battery power is present The READY indicator is off Auto Press CTRL 2 This is the normal operating mode Th
82. tem to the End User within one 1 business day after Company receives the defective Product from the End User In any case Company will provide shipping instructions and will pay its designated carrier for all shipping charges for return of defective equipment and replacement of Warranted Items Any returned Warranted Item or parts that are replaced may be new or reconditioned All Warranted Items returned to Company and all parts replaced by Company shall become the property of Company Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 69 www eaton com powerquality WARRANTY WHAT THIS LIMITED WARRANTY DOES NOT COVER This Warranty does not cover any defects or damages caused by a failure to properly store the Product before installation including the charge of batteries no later than the date indicated on the packaging b shipping and delivery of the Product if shipping is FOB Factory c neglect accident abuse misuse misapplication or incorrect installation d repair or alteration not authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or Agent e improper testing operation maintenance adjustment or modification of any kind not authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or Agent or f use of the Product under other than normal operating conditions or in a manner inconsistent with the
83. tery cabinet Remove the bolts that hold the front of the battery cabinet to the rack Pull the battery cabinet out slightly unscrew the panel screw and lift open the hinged panel Turn on the DC switch e Close and secure the top panel Slide the battery cabinet back in the rack Reinstall the bolts to secure the front of the battery cabinet to the rack 4 Start the UPS on battery power Use the FERRUPS key to turn the UPS ON OFF switch to the ON position After a brief self check the BATTERY POWER and READY indicators illuminate The UPS beeps every 20 seconds indicating the UPS is running on battery power The control panel scrolls this display FERRUPS Mode Auto Charger Off Beeper Enabled NOTE If the ALARM indicator is on read the alarm message on the control panel display turn the UPS ON OFF and DC switches to the OFF position and call your service representative 5 For Plug Receptacle UPSs Turn the AC input power on at the service panel The AC LINE indicator illuminates After a few seconds the UPS switches from battery power to AC input power The BATTERY POWER indicator turns off J OLL AC LINE READY CHARGING BATTERY ALARM POWER Figure 6 Front Panel Indicators 22 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality UPS STARTUP For Hardwired UPSs Turn the AC line disconnect switch to the ON position The AC LINE indicator illuminate
84. testing operation maintenance adjustment or modification of any kind not authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or Agent or f use of the Product under other than normal operating conditions or in a manner inconsistent with the Product s labels or instructions This Warranty is not valid if the Product s serial numbers have been removed or are illegible Any Warranted Items repaired or replaced pursuant to this Warranty will be warranted for the remaining portion of the original Warranty subject to all the terms thereof Company shall not be responsible for any charges for testing checking removal or installation of Warranted Items COMPANY DOES NOT WARRANT EQUIPMENT NOT MANUFACTURED BY COMPANY IF PERMITTED BY THE APPLICABLE MANUFACTURER COMPANY SHALL PASS THROUGH SUCH MANUFACTURER S WARRANTIES TO END USER COMPANY DOES NOT WARRANT SOFTWARE INCLUDING SOFTWARE EMBEDDED IN PRODUCTS THAT IS NOT CREATED BY COMPANY WITHOUT LIMITING THE FOREGOING COMPANY SPECIFICALLY DOES NOT WARRANT SOFTWARE SUCH AS LINUX THAT WAS CREATED USING AN OPEN SOURCE MODEL IS DISTRIBUTED PURSUANT TO AN OPEN SOURCE LICENSE 72 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality WARRANTY THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY OFFERED BY COMPANY WITH RESPECT TO THE PRODUCTS AND SERVICES AND EXCEPT FOR SUCH FOREGOING WA
85. this key Display shows DISPLAY Display 0 Display 0 ENTER 00 Time 11 30 20 PROGRAM 00 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 23 www eaton com powerquality UPS STARTUP Enter the correct time in 24 hour format For example if the time is 9 30 a m Press this key Display shows 9 3 0 00 Pgm 930 ENTER 00 Time 09 30 00 The date is parameter 10 To set the date follow these steps Press this key Display shows DISPLAY Display 1 0 Display 10 ENTER 10 Date 01 01 96 PROGRAM 10 Pgm Enter the correct date in MMDDYY format For example to enter June 4 1993 Press this key Display shows 0 6 0 4 9 3 10 Pgm 060493 ENTER 10 Date 06 04 93 If your FERRUPS Rack Mount UPS is configured to use an external battery cabinet you must program the battery capacity in ampere hour Ah for the total number of battery packs used in the UPS If you purchased one of the FERRUPS Rack Mount battery pack options available from Eaton select the Ah value from Table 2 Before programming the battery Ah enter the user level password following the instructions in Entering Passwords on page 30 To change the battery Ah parameter 69 Batt Ah follow these steps Press this key Display shows DISPLAY 6 9 ENTER 69 Batt AH Default PROGRAM 69 Pgm Ah Value from Table 2 69 ENTER 69 Pgm new value where xxx is th
86. traight through connections for the pins shown in Figure 11 and Figure 12 For RS 232 communication use Pins 2 transmit data 3 receive data and 7 signal ground For hardware handshaking request to send on Pin 4 and clear to send on Pin 5 contact your service representative No other pins should be connected from the UPS RS 232 port to your terminal or computer For more information on pin connections and the function of the non serial pins on the RS 232 port see Table 6 on page 42 Remote Monitoring on page 49 and Remote Shutdown on page 50 NOTE To connect a modem see TIP 503 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 43 www eaton com powerquality COMMUNICATION DB25P MALE DB9 TO TO FERRUPS 2 2 DCE DCE US 102 p 27D nos 5 7 3RD DTR 4 1 o 505 m a DSR 6 At gt RTS 7 6 759 CTS 8 7 8 Figure 11 DB 9 to UPS Pinout DB25 TO DB25P MALE COMPUTER E TO FERRUPS DTE 2 2 DCE TD2 3 3 RD3 2TD RTS 4 7 3RD CTS 5 Cane 5 5 67 DCD 8 6 736 20 8 20 J Figure 12 DB 25 to UPS Pinout Connect the cable from the RS 232 port on the UPS rear panel to the serial port on your terminal or computer Your terminal
87. ugged READY On The UPS is ready to provide battery backup power when needed Off The UPS cannot provide battery backup power because Itisin the Line Condition mode or the Off mode see the following section Using the Control Panel The batteries may be discharged It may be running on battery power Inverter On mode Flashing The UPS is testing the batteries as part of the automatic system test see Automatic System Test on page 33 or you have started a timed shutdown see Table 9 on page 46 CHARGING On The UPS is charging its batteries Off The battery charger is off batteries are at full charge BATTERY POWER On The UPS is providing power from its batteries it is in the Inverter On mode Off The UPS is providing conditioned power from the AC input power source or the UPS is off Flashing The UPS is testing the inverter as part of the automatic system test see Automatic System Test on page 33 ALARM On The UPS is warning you that an alarm exists If you have not silenced the alarm the beep sequence identifies the problem see Alarms on page 61 If you have a control panel an alarm message appears on its display Off No alarm exists 28 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality OPERATION Using the Control Panel The control panel comes with all 4 3 7 kVA models If you have an 850 VA 3 1 kVA model you may have ordered the remo
88. ulamentos de Seguranca INSTRU ES DE SEGURAN A IMPORTANTES GUARDE ESTAS INSTRUCOES Este manual cont m instru es importantes que devem ser seguidas durante a instala o e manutenc o do no break e das baterias Leia todas as instruc es antes de operar o eguipamento e guarde este manual para consult lo futuramente CUIDADO A UPS cont m VOLTAGEM MORTAL Todos os reparos e assist ncia t cnica devem ser executados SOMENTE POR PESSOAL DA ASSISTENCIA TECNICA AUTORIZADO N o h nenhuma PECA QUE POSSA SER REPARADA PELO USUARIO dentro da UPS ADVERTENCIA e Esta UPS cont m sua propria fonte de energia baterias Os recept culos de saida podem conter voltagem ativa quando a UPS n o se encontra conectada a uma fonte de alimentac o de corrente alternada N oremova ou desconecte o cabo de entrada quando a UPS estiver ligada Isto aterramento de seguran a da UPS e do equipamento conectado e Para reduzir risco de inc ndios ou choques el tricos instale a UPS em ambiente interno com temperatura umidade controladas livres de contaminadores condutiveis A temperatura ambiente n o deve exceder 40 C opere pr ximo gua ou em umidade excessiva max 95 Para estar de acordo com os padr es internacionais e os regulamentos de fiac o o equipamento total conectado a saida desta UPS n o deve ter uma corrente de fuga terra maior que 1 5 miliamp res e As baterias pode
89. urned off 11 or DISPLAY 1 1 ENTER 11 Amb Temp 23c Change Not Allowed ambtemp at The temperature in Celsius inside the UPS The UPS sounds an alarm and shuts down if this value is too high 12 12 SinkTemp 26c Change Not Allowed heatsinktemp st The temperature of the heatsink The UPS sounds an alarm if this value is too high Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 35 www eaton com powerquality OPERATION Parameter Parameter Name Number Sample Display Password Short Form Explanation 13 13 Reserved Reserved 14 14 XfmrTemp 28c Change Not xfmrtemp The temperature of the transformer The Allowed xt UPS sounds an alarm and shuts down if this value is too high NOTE The display always shows 63c on FERRUPS models that do not use a transformer temperature probe 15 15 Unit ID None unitident UPS ID An identification string that can be Network 1 UPS id configured for use with your network 16 16 FullLoad 075 Change Not fullload Percent of full load The percentage of the Allowed 1 UPS s total capacity that is actually being used by your eguipment 17 17 Watts 546 Change Not watts The total real power your equipment is Allowed w drawing from the UPS 18 18 PF 0 73 Dist Change Not powerfact The power factor of your equipment the Allowed pf difference in the way it draws voltage and current Po
90. viced 2 3 Before you move it 4 When it has gone into the Off mode because the batteries have been discharged during an extended outage 5 When a system malfunction requires a UPS shutdown Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 37 www eaton com powerguality OPERATION 38 CAUTION When AC input voltage is present the UPS system can provide output voltage even though its batteries are disconnected To confirm that there is no UPS output voltage always disconnect the AC input source if the UPS has one or more separate battery cabinets open the DC disconnect switch on each battery cabinet or disconnect the battery cabinet from the UPS 1 UPSs with no bypass switch Turn off the protected eguipment Continue to Step 2 If you need to use the eguipment while the UPS is off plug the equipment into standard wall outlets and restart the equipment UPSs with a Break Before Make BBM bypass switch see the label on the side of the switch Shut down the protected eguipment Turn the bypass switch to the LINE position Continue to Step 2 If you need to use the eguipment while the UPS is off restart the eguipment The eguipment receives direct AC line instead of conditioned power from the UPS UPSs with a Make Before Break MBB bypass switch see the label on the side of the switch Verify that the AC LINE indicator is on the BATTERY POWER indicator is off and the UPS is provi
91. wer factor is equal to Watts Out parameter 17 divided by VA Out parameter 5 This parameter also tells whether the power factor is leading Lead lagging Lag or distortion Dist 19 19 VALimit 850 Change Not valimit The maximum volt amps the UPS can Allowed val supply to your equipment at the present power factor The UPS sounds an alarm when VA Out parameter 5 is higher than this value 20 20 PwrOut 1 Change Not powerout The number of times there has been a loss Allowed po of input power since you started the UPS 21 21 0vrLds 0 Change Not overloads The number of times the UPS has sensed an Allowed ol overload that is the number of times VA Out has been greater than VA Limit 22 22 SysHrs 00000 Change Not syshours The total number of hours the UPS has been Allowed sh operating regardless of mode This number does not increase when the UPS ON OFF switch is in the OFF position 23 23 InvMin 0000 0 Change Not invmin The total number of minutes the inverter Allowed im has run since startup 36 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerquality OPERATION Parameter Parameter Name Number Sample Display Password Short Form Explanation 24 24 Inverter Log Change Not inverterlog A record of the date time duration and L 0319 2127 1215 Allowed il reason for the last 20 inverter battery power runs see Alarm and Inverter Logs on page 64 25 2
92. xternal Battery Pack Ah Values for 1 8 3 1 kVA UPS Models Battery Pack Battery Ah Tre 100 2re 150 Startup for the FER OFER 4 3 7 UPS Before starting up the UPS review the rear panel for your UPS model Battery O Output Receptacle Cable Input lo Q e Panel Optional m mn Communication Port Figure 5 FERRUPS Rack Mount 4 3 7 kVA Rear Panel To start the FER OFER 4 3 7 kVA UPS use the following steps 1 Confirm the equipment to be protected by the UPS is powered off 2 For Plug Receptacle UPSs Verify that the AC input power is off at the service panel Plug the UPS power cord into power outlet NOTE If the plug does not match your receptacle outlet ask your electrician to install the proper outlet For Hardwired UPSs Confirm that an electrician has completed and tested the connection to the proper power source and connected your protected equipment according to the Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA Installation Guide Confirm that your AC line disconnect switch and the UPS ON OFF switch are both in the OFF position 3 lf you have an RBC 1 or RBC 2 battery cabinet skip to Step 4 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 21 www eaton com powerquality UPS STARTUP If you have an RBC 3 battery cabinet turn the DC switch to the ON position e The DC switch is located under the hinged panel on the top of the bat
93. y cabinet to the rack Pull the battery cabinet out slightly unscrew the panel screw and lift open the hinged panel Turn off the DC switch e Close and secure the top panel Slide the battery cabinet back in the rack Reinstall the bolts to secure the battery cabinet to the front of the rack 5 If the UPS is turned off for an extended period of time recharge the batteries every 90 120 days to prevent battery damage restart the UPS see UPS Startup on page 17 Extended Power Outages If the power is out for an extended time the UPS continues to provide power for your eguipment until it gets near the end of its run time You can check the remaining battery run time by reading parameter 9 see page 35 At a preset number of minutes before the end of the run time factory default setting is five minutes the UPS sounds a Low Runtime alarm e Shut down your equipment and turn off the UPS to conserve the remaining battery power see UPS Shutdown on page 37 When AC input power returns turn on the UPS to recharge the batteries If your UPS shuts itself down because its battery voltage is too low shut down the UPS until the AC input power returns see UPS Shutdown on page 37 Eaton FERRUPS Rack Mount UPS 850 7 kVA User s Guide 164201424 Rev 1 39 www eaton com powerguality OPERATION 40 Eaton FERRUPS Rack Mount UPS 850 VA 7 kVA User s Guide 164201424 Rev 1 www eaton com powerguality
94. y grounded and wired outlets using no extension cords adapters other ground wires or other electrical connectors 2 The installation of the UPS complies with all applicable electrical and safety codes described by the National Electrical Code NEC 3 The UPS was used under normal operating conditions and in accordance with all labels and instructions and 4 The UPS was not damaged by accident other than AC power line transient misuse or abuse Cumulative Limits to be paid by Guarantor under this Load Protection Guaranty 25 000 for Eaton UPS Model 3105 gt 150 000 for Eaton UPS Models 5110 5115 5125 and 5130 250 000 for Eaton UPS Models 9120 9125 9130 9135 9140 9150 9155 9170 and FERRUPS products WHAT THIS GUARANTY DOES NOT COVER Any reimbursement or repair to End User s equipment does not include reimbursement for or restoration of any data loss This Guaranty does not cover any defects or damages caused by a failure to properly store the Product before installation including the charge of batteries no later than the date indicated on the packaging b shipping and delivery of the Product if shipping is FOB Factory c neglect accident abuse misuse misapplication or incorrect installation of Product d repair or alteration of Product not authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or Agent e improper testing operation maintenance a

Eaton FERRUPS

Contents

Download Pdf Manuals

Related Search

Related Contents