EverFocus EQ250A/N surveillance camera
Contents
1. LL Line Lock OF F ON To select the sync mode between Internal Sync LL off and Line Lock LL on Set the line lock off the camera will synchronize to the internal time base Set the line lock on the camera s vertical synchronization can be driven by the AC signal in the power lines Note The cameras feature AC line lock for external synchronization using the AC power frequency 60Hz is possible but not available in using DC or other operation power such as NTSC in 50Hz or PAL in 60Hz power system VD DD Auto Iris lens Type For video drive auto iris lens please set switch to VD For direct drive iris lens set switch to DD The default setting is DD Wire the cable of lens to lens connector according to the following table Pinl Pin2 Pin3 Pin4 Lens Connector Video Drive 12V GND VD IRIS GND 1 3 Direct Drive Cnt Cnt Drv Drv 6 IRIS Level Control Brightness Level can be adjusted from the IRIS level VR while using the direct drive lens Turn counterclockwise to L to get darker picture Turn clockwise to H to get brighter picture 7 V Phase Adjustment Screw The vertical phase may require adjustment to synchronize the vertical phase of the camera with other camera in the system when it 18 to be used in the line lock sync mode Make the adjustment when the vertical phase of the camera does not match with other cameras 8 Mounting Base and Fixing Screws To use when the mounting bracket is required while mou2. Albert Einstein Strasse 1 D 46446 Emmerich Germany TEL 49 2822 9394 0 www evertocus de China Office Room B 05D 1 KESHI PLAZA Shangdi Information Industry Base Haidian District Beijing China 100085 TEL 86 10 62973336 37 38 39 FAX 86 10 62971423 www evertocus com cn Japan Office 1809 WBG MARIBU East 18F 2 6 Nakase Mihama ku Chiba city 261 7118 Japan TEL 81 43 212 8188 FAX 81 43 297 0081 www everfocus com EverFocus P N MQ35G02100_Ver B
3. iv Tighten the locking screw while the adjustment is completed EverFocus Electronics Corp Head Office 12F No 79 Sec 1 Shin Tai Wu Road Hsi Chih Taipei Taiwan TEL 886 2 26982334 FAX 886 2 26982380 www everfocus com tw USA L A Office 1801 Highland Ave Unit A Duarte CA 91010 U S A TEL 1 626 844 8888 FAX 1 626 844 8838 www everfocus com USA N Y Office 415 Oser Avenue Unit S Hauppauge NY 11788 TEL 631 436 5070 FAX 631 436 5027 www everfocus com Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled an This symbol means ae electrical and electronic equipment at their end of life should be las of separately from your Please ee this equipment at your nn un waste collection recycling 7 ie European Union there are separate collection ae for used electrical and electronic produc help us to conserve the environment we live in Ihr EverFocus Produkt wurde entwickelt und hergestellt mit qualitativ hochwertigen Materialien und Komponenten die a und wieder verwendet werden k nne Dieses Symbol bedeutet dass elektrische und elektronische Ger te am Ende Nutzungsdauer vom Hausm ll oetrenni household waste entsorgt werden sollen Bitte entsorgen Sie dies Ger t bei Ihrer rtlichen kommunalen Sammelstelle oder im Recycling Centre Helfen Sie uns bitte die Umwelt zu erhalten in der wir leben Europe Office
4. EVERFOCUS 1 3 Sony CCD Aluminum Box Housing Color Camera Operation Instructions Model No EO350 E0250 Please read this manual first for correct installation and operation This manual should be retained for future reference The information in this manual was current when published The manufacturer reserves the right to revise and improve its products All specifications are therefore subject to change without notice PRECAUTIONS 1 Do not install the camera near electric or magnetic fields Install the camera away from TV radio transmitter magnet electric motor transformer audio speakers since the magnetic fields generate from above devices will distort the video images 2 Never disassemble the camera nor put impurities in it Disassembly or impurities may result in trouble or fire 3 Never face the camera toward the sun Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit 4 Keep the power cord away from water and liquid Touching the wet power cord may result in electric shock 5 Never install the camera in areas exposed to water oil or gas Water oil or gas may result in failure electric shock or fire Cleaning Do not touch the surface of sensor by hand directly Use a soft cloth to remove the dirt from the camera body Use lens tissue or a cotton swab and ethanol to clean the sensor and the camera lens 7 Do not operate the camera beyond the specified temperat
5. fields sec PAL 625 TV lines 50 fields sec Horizontal Resolution 560TVL 380TVL 051 ERTSE Electronic Shutter 1 50 1 60 1 100 000 C CS mount Lens Type w Drive Direct Drive Back Back Light Comp Comp ONIOFF Switch 00000 Switch Auto Gain Control ON OFF Switch Sync Mode Line Lock Internal Line Lock Internal Syne Phase Control V Phase 90 2 types Power Source 100V AC 240V AC 12VDC 24VAC 100VAC 240VAC 12VA max Scanning System Power Consumption 24V AC TVA max 12VDC 4 5W max l l 5 mm W 51mm H 140 2mm D Dimensions 2 25 W 2 H x 5 52 D Operating Temperature 0 C 50 C 32 F 122 F 20 80 Humidity DIMENSIONS 140 2mm 5 52 57mm 2 25 Unit mm inch MAJOR PARTS NAME amp THEIR FUNCTIONS Side 1 Rear EO series Rear EO series A 1 Focal Length Adjustment Ring Use this ring to adjust the appropriate focal length according to the type of lens Rotate the ring clockwise for the CS mount lens rotate it counterclockwise for the C mount lens The factory setting is CS mount 2 Lens Mount To mount an appropriate C mount or CS mount lens 3 Locking Screw Use the locking screw to fix the focal length 4 Lens Connector 4 pin socket To connect to the lens plug of the auto iris lens 5 Control Switches There are 6 control switches located on the sideboard which are for the sett
6. ing of the special features The switches in orders are for Flickerless Back Light Compensation Electronic Shutter Automatic Gain Control Line Lock and Auto Iris Lens type Fluorescent ON OFF This is a compensation function for against the images flicker fiercely during fluorescent light condition Shooting the images in fluorescent light by using turn on the Fluorescent function the default setting is Off BLC Back Light Compensation ON OFF When BLC is turned on the AGC ES and IRIS operating point is determined by averaging over the center area instead of entire field of view so that a dimly lit foreground object at center area can be clearly distinguished from brightly lit backgrounds BLC should not be used unless it is needed to compensate for back lit The default setting 1s OFF ES Electronic Shutter OFF ON ES ON The camera continuously adjusts the shutter speed from 1 60 NTSC 1 50 PAL second to 1 100 000 second according to the luminance conditions of the scene ES OFF The shutter speed is fixed at 1 60 NTSC 1 50 PAL second Set ES OFF when auto iris lens is used or flicker is observed under a very bright fluorescent lamp Otherwise turn ES on for optimum performance The default setting is ON AGC Automatic Gain Control OFF ON AGC ON The sensitivity increases automatically when light is low AGC OFF A low noise picture is obtained under a low light condition The default setting is ON
7. nting the camera The mounting base can be attached to either the top or the bottom of the camera fix the mounting base onto the camera by using the 4 supplied fixing screws 9 Video Output Connector BNC VBS 1 0 Vp p 75ohm 10 Power Cable EQ series 11 12VDC 24VAC Screw Terminals EQ series A 12 Audio Output optional Connect with an audio device RCA connector INSTALLATION 1 Remove the cover cap from the top of the lens mount 2 To attach a C mount CS mount lens turn the focal length adjustment ring to the appropriate position Note If a C mount lens is used please make sure the focal length adjustment ring is set at C position before fixing the lens 3 Screw the lens firmly onto the lens mount Insert the lens plug in the lens connector if the auto iris lens is used 4 Tighten the locking screw 5 Connect the video output of the camera to a color monitor or other video device through a 75 ohm type coaxial cable with BNC female connector 6 Plug the power cord to the outlet 7 Once the image appears on the monitor adjust the focus and diaphragm of the lens to obtain the best picture 8 If the subject is not in focus when adjusting focus of lens do focal length adjustment as following i Loosen the locking screw of the focal length adjustment ring 11 Take picture of subject at a distance more than 20m away from the camera 111 Rotate the focal length adjustment ring to bring the subject in focus
8. ure humidity or power source ratings Use the camera at temperatures within 0 C S0 C 32 F 122 F and humidity between 20 80 The input power source are 12VDC 24VAC 100 240VAC PREFACE This new series 1s a solid state color video camera specially designed for high quality surveillance applications It incorporates break through DSP technology that provides most reliable and accurate color picture in security industry The camera is convenient to use with C mount or CS mount lenses and easy back focus adjustment help to achieve installation efficiency FEATURES Industry leading super high res with 560 TVL EQ350 model Revolutionary integrated 10 bit Digital Signal Processor DSP delivers sharp color images and excellent picture quality Wide range automatic electronic shutter 1 60 1 50 1 100 000 Auto line lock with external phase adjustment C mount or CS mount adjustable with easy back focus adjustment wheel on the camera Smart FL mode for fluorescent light or 1 100 sec NTSC Utilizing innovative Pure Vision Technology STANDARD ACCESSORIES gt Camera Unit 1 gt Accessory Pack includes Mounting Base for bracket M2 Screws x 4 for fixing mounting base Lens Connector gt Manual x 1 SPECIFICATIONS Type 350 EQ250 Pickup Device 1 3 SONY Super HAD CCD l NTSC 768 H x 494 V NTSC 510 H x 492 V Picture Elements PAL 752 H x 582 V PAL 500 H x 582 V NTSC 525 TV lines 60
Download Pdf Manuals
Related Search