Hunter The Baseball Fan - 44"
Contents
1. A WARNING Do not carry or lift fan by canopy or motor wires 3 10 Lift the fan and place a hole in the canopy over the ceiling plate hook 3 11 Align the slot on the ball with the tab on the hanger bracket and place the ball into the hanger bracket Go to 4 Wiring the Fan A WARNING Fan may fall if not assembled as directed in these installation instructions 41081 01 08 04 09 Hunter Fan Company All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 Make sure the power to the outlet box and associated wall switch location is still OFF To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight Single Switch Wiring If you want to you can control both fan and light with one switch To do so connect the wires as follows e The bare or green ground wire from the ceiling to the green ground wire from the hanger bracket and the green ground wire from the fan e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black and the black white wire from the fan Dual Switch Wiring e The bare or green ground wire from the ceiling to the2. Mounting hangs from the ceiling by a downrod included recommended for ceilings 8 feet or higher 41081 01 08 04 09 Hunter Fan Company Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons in sets as they were shipped 1 Getting Ready To install a ceiling fan be sure you can do the following Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip if available e Phillips head screwdriver magnetic tip if available e Wrench or pliers Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide for details Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact the Hunter Technical Support Department at 888 830 1326 In Canada call 1 866 268 1936 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building struc
3. Type 2 Models Owner s Guide and Installation Manual Welcome For Your Records and Your new Hunter ceiling fan is an addition to your home or office that Warranty Assistance will provide comfort and performance for many years This installation For reference also attach your receipt or a copy of your receipt to the manual and operation manual gives you complete instructions for installing and operating your fan Model Name We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Model No Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Date Purchased Cautions and Warnings eende READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied Table Of Contents 1 Getting Ready To avoid possible electrical shock before installing your fan 2 Installing the Hanger Bracket disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fast
4. en a prominent warning device such as a tag to the service panel 5 Installing the Canopy All wiring must be in accordance with national and local electrical 6 Installing the Light Fixture codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls 3 e Assembling and Hanging the Fan 4 Wiring the Fan 7 Operating and Cleaning Your Ceiling 2009 Hunter Fan Company 41081 01 08 04 09 Hunter Fan Company Mounting and Optional Accessories Understanding Mounting Hunter s mounting system provides you maximum installation flexibility and ease This fan may only be mounted in a Standard Mounting style as directed in these instructions This fan cannot be low profile or angle mounted Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted speed control This fan cannot use remote control speed controls To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls Standard
5. green ground wire from the pipe ball assembly e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black wire from the fan e The black white wire from the fan to the wire for the wall switch A CAUTION Be sure no bare wire or wire strands are visible after making connections Push all wires and wire connectors into the outlet box Wire Connector ie Single Switch Wiring Ko E White ay Ground Green Black Black 7 White Ground Green N White Black Dual Switch Wiring be x Y H E White Wall Switch lt T Ground Green Black iF J A Black Ground Green White White Black 41081 01 08 04 09 Hunter Fan Company 5 e Installing the Canopy Steps 5 1 5 2 nly Keyhole Slot 5 1 Lift the canopy off of the ceiling plate hook Align the two keyholes in the canopy with the two partially installed screws in the ceiling plate Rotate to engage the screws in the narrow ends of the keyholes and securely tighten the screws Install the remaining two screws through the holes in the canopy and into the ceiling plate Remove the backing from the adhesive dots position the decal on the ceiling and press the decal to adhere to the ceiling 41081 01 08 04 09 Hunter Fan C
6. in the ramp blade and blade bracket with the holes in the top of the fan Blade Bracket Blade Use the 1 1 4 long mounting screws to attach the taller end of the blade assembly to the fan and the 7 8 short mounting screws to attach the shorter end of the blade assembly to the fan Tighten all screws securely Leaving the backing on one side of the dots place the adhesive dots onto the back of the decorative decal the side without printing Note If you have a textured ceiling you may need to smooth a Step 3 5 surface for the dots to adhere or purchase a thicker adhesive Rest the decorative decal over the motor shaft with the printed side down Long Mounting Screw Adhesive ia ae eae Short Mounting acking Screw 7 8 Printed Side do not install adhesive dots on this side 41081 01 08 04 09 Hunter Fan Company 3 e Assembling and Hanging the Fan Thread the wires from the fan through the canopy Thread the wires from the fan through the pipe ball assembly Loosen the square head set screw in the pipe Screw the pipe ball Square assembly onto the threaded pipe from the motor Retighten the Seton set screw in the pipe ball assembly using a wrench or pliers Step 3 9 A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod
7. lowly to change settings e Release slowly to prevent the chain from recoiling into the blades The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector The light pull chain controls power to the light The pull chain has In warm weather use two settings On and Off downward air flow pattern Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added In cold weather use upward protection and beauty Clean painted and high gloss blades in the air flow pattern same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the oppo
8. mphis Tennessee 38016 41081 01 08 04 09 Hunter Fan Company
9. ompany 6 Installing the Light Fixture Partially install two globe fitter screws into the two holes in the bottom of the fan To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight Connect the black wire from the fan to the black wire from the light fixture e Connect the white wire from the fan to the white wire from the light fixture Push the wires and wire connectors into the hole in the bottom of the fan 6 3 Align the keyholes in the globe fitter with the two partially installed globe fitter screws Rotate the fitter counterclockwise to engage the screws in the narrow ends of the keyholes Securely tighten the screws Install included CFL 19 Watt max bulb into the light socket T ANNO Thumbscrew Partially install the three thumbscrews into the globe fitter Insert the glass globe into the fitter and securely tighten the three oa thumbscrews Globe Fitter Screw p gt gt gt 9 gt gt gt 9 gt gt gt gt n Thumbscrew Partially Installed Screws Globe Fitter Steps 6 1 6 3 Steps 6 4 6 6 41081 01 08 04 09 Hunter Fan Company 7 Operating and Cleaning Your Ceiling Fan 7 1 Turn on electrical power to the fan 7 2 The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain s
10. site position Restart fan Reversing Switch 41081 01 08 04 09 Hunter Fan Company 8 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker Turn wall switch on 2 Loosen canopy check all connections according to the Wiring the Fan section 3 Push motor reversing switch firmly left or right to ensure that the switch is engaged 4 Pull the pull chain to ensure it is on 5 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Check to see if the blade is cracked If so replace all the blades 3 Tighten all screws Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated Problem Lights dim when turned on or do not turn on 1 Check to make sure wattage of light bulbs installed match the specifications on the light socket Problem If the light on this fan shuts off suddenly 1 Turn the power to the fan off at the wall switch Wait 30 seconds then resume power to the fan If you need parts or technical assistance please call 888 830 1326 In Canada 1 866 268 1936 or visit us at our web site at http www hunterfan com Hunter Fan Company 7130 Goodlett Farms Pkwy 400 Me
11. ture are essential for safety reliable operation maximum efficiency and energy savings 41081 01 08 04 09 Hunter Fan Company 2 Installing the Hanger Bracket Drill two pilot holes into the wood support structure through the outermost holes in the outlet box using the ceiling plate as a guide The pilot holes should be 9 64 in diameter Install one canopy screw into each side of the ceiling plate as shown Place a flat washer on each of the two 3 wood screws Thread the lead wires from the outlet box down through the hole in the middle of the ceiling plate Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure Pass the wood screws through the slotted holes in the hanger bracket into the pilot holes you drilled Tighten the wood screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Canopy Screw a Flat Washer 3 Wood Screw 41081 01 08 04 09 Hunter Fan Company 3 e Assembling and Hanging the Fan 3 1 Remove the blade mounting screws and rubber shipping bumpers SEV Tene Short from the motor Mounting Mounting Screw y Screw Y 3 2 Assemble the blade ramp blade and blade bracket as shown Note The blades are two sided Select which side you would like to see and install it face down 3 3 Align the holes
Download Pdf Manuals
Related Search