Hunter Concert Breeze - 52"
Contents
1. To assemble fan to hang down from a flat or angled ceiling place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly Feed the wires from the fan through the downrod Note Make sure all the wires are on the same side of the metal dowel pin inside the dowrod Loosen the square head setscrew on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the setscrew with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod A WARNING Do not carry or lift fan by canopy Raise the fan and place the ball into the hanger bracket Align the notch on the ball with the indent in the hanger bracket Rotate the fan until you hear the notch pop into place Go to 4 e Wiring the Fan A WARNING Fan may fall if not assembled as directed in these installation instructions 6 Steps 3 1 3 3 7 m Downrod lt Canopy with Washer Canopy Trim Adapter Ring Steps 3 4 3 5 45049 01 07 13 09 Hunter Fan Company 3 e Assembling and Hanging the Fan Low Profile Only You can assemble your fan for standard or angled mounting as shown in steps 3 1 32. source i tronsmitter ons bottom view 300ft yess C NOTE For Optimal sight Performance Place the Maestro at least 5 away from all wireless devices speaker wire not included Speaker Wire Installation walls and other obstructions may limit range 16 45049 01 07 13 09 Hunter Fan Company 10 Installation and Setup of Maestro and Remote Continued Maestro Powering the Maestro AC Adaptor 10 1 Plug the AC adaptor into the back of the Maestro in the port labeled power 10 2 Select the correct channel by sliding the switch to the desired channel S For 3 5mm Stereo Cable Installation 10 3 Plug a 3 5mm stereo cable into the back of the Maestro in the port labeled line in SS 10 4 Plug the other end of the 3 5mm stereo cable into your audio device n ot N i P jA 3 5mm Stereo For Speaker Wire Installation Lo Cable Tha 10 5 Connect the speaker wire not included to the speaker e W om input terminals on the bottom of the Maestro Make sure that the plus and the minus signs on the Maestro correspond with the plus and the minus signs on your audio device 10 6 Make sure that all connections are firm A NOTE Contact between bare speaker wires at the terminals can cause a short circuit 10 7 Install the included 3 volt battery into the transmitter This product includes one 3 vo
3. outermost holes in the outlet box The pilot holes should be 9 64 in diameter Note Your fan comes with four pre installed neoprene noise isolators Thread the lead wires from the outlet box down through the hole in the middle of the hanger bracket Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other If you are installing the fan on an ANGLED ceiling be sure to orient the hanger bracket as shown in Illustration 2 3 left or right view Note The isolators should be flush against the ceiling Place a flat washer on each of the two 3 screws and pass the screws through the slotted holes in the hanger bracket into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer Large n 3 Screw LEFT ALAALA a y 5 Isolator Hanger Bracket Steps 2 2 2 4 Ceiling Peak Step 2 3 Angled Ceiling Only 45049 01 07 13 09 Hunter Fan Company Ceiling Peak Large 3 Assembling and Hanging the Fan You can assemble your fan for standard or angled mounting as shown in steps 3 1 3 3 For low profile mounting ceilings less than 8 feet high go to steps 3 6 3 9 on the next page 3 1 3 2 3 3 3 4 3 5
4. 3 on the previous page For low profile mounting ceilings less than 8 feet high see steps 3 6 3 10 on this page 3 6 Remove the screws from the hanger ball bracket 3 7 Place the low profile washer from the parts sack into the canopy 3 8 Place the canopy trim ring and canopy with washer on top of the fan assembly 3 9 Align the screw holes in the washer with the holes in the adapter Assemble securely with three 8 32 x 3 4 screws 3 10 Raise the fan and place the hook on the hanger bracket through the round hole in the rim of the canopy A WARNING Fan may fall if not assembled as directed in these installation instructions Steps 3 8 3 9 Low Profile Washer s ea Step 3 7 Detail G ra S I L ett Ne Low Profile Washer 4 Z Adapter T 8 32 x 3 4 Screw Canopy Trim Ring Step 3 10 7 45049 01 07 13 09 Hunter Fan Company 4 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 Before attempting installation make sure the power is still off 4 2 To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise u
5. Raise the canopy over the hanger bracket Align partially installed screws with key slots in canopy Twist canopy clockwise to secure Install third amp fourth canopy screw in round hole on canopy Securely tighten all four screws Using both hands push the canopy trim ring up to the top of the canopy Twist canopy trim ring clockwise to secure the canopy Should you need to remove the canopy trim ring follow these steps 1 Twist canopy trim ring counter clockwise until it releases from canopy Step 5 5 9 Steps 5 1 5 2 Hanger Bracket f gt Canopy Trim 7 Ring Step 5 4 45049 01 07 13 09 Hunter Fan Company 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets Step 6 1 Detail insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 Remove the blade mounting screws and rubber shipping bumpers from the motor Note Some blade mounting screws are installed in the motor to secure shipping blocks 6 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade m
6. ae ie Concert Breeze Owner s Guide and Installation Manual Manual De Propietario SINCE 1886 Form 45049 01 20090713 2009 Hunter Fan Co Welcome For Your Records and Warranty Assistance Your new Hunter ceiling fan is an addition to your home or office that i E E ae ee a will provide comfort and performance for many years This installation or your receipt fo the manuali g F and operation manual gives you complete instructions for installing and operating your fan Model Name We are proud of our work We appreciate the opportunity to supply O you with the best ceiling fan available anywhere in the world Model No Before installing your fan for your records and warranty assistance O record information from the carton and Hunter nameplate label Date Purchased located on the top of the fan motor housing eee Cautions and Warnings ee READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING Table Of Contents INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions 3 Assembling and Hanging the Fan 6 and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circu
7. em Noisy operation 1 Tighten the blade assembly screws and blade iron armature screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated Problem Lights dim when turned on or do not turn on 1 Check to make sure the wattage and type of light bulbs installed match the specifications on the light socket Problem Sound does not come on 1 Check to make sure the Maestro has power 2 Press the MUTE button to turn on the speaker 1 Change the channel on the Maestro and the fan See Changing the Channel on the Maestro and the Fan 2 Change the channel on the wireless device 20 45049 01 07 13 09 Hunter Fan Company If you need parts or service assistance please call 3 Make sure that the speaker is on the correct channel 888 830 1326 or visit us at our Web site at Problem Interference with wireless devices http www hunterfan com Hunter Fan Company 7130 Goodlett Farms Pkwy 400 Memphis Tennessee 38016
8. it breakers in the off position securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical 9 Operating and Cleaning Your Ceiling codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician 10 Installation and Setup of Maestro and To reduce the risk of personal injury do not bend the blade Remote attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed 1 Getting Ready 2 Installing the Hanger Bracket 4 Wiring the Fan 5 Installing the Canopy and Canopy Trim 6 Assembling the Blades 7 Light Speaker Assembly Installation 11 11 Operating the Remote Control Light Speaker 12 e Changing the channel on the Maestro die controls 13 Troubleshooting 2009 Hunter Fan Company 2 45049 01 07 13 09 Hunter Fan Company Installer s Choice and Optional Accessories Support Brace Ceiling Standard Outlet Box Mounting gt Style Standard Mounting hangs from the ceiling by a downrod included Angled Mounting recommended for a vaulted or angled ceiling Understanding Mounting and Installers Choice Hunte
9. lt type CR2025 battery for use with the remote control transmitter Please contact your local battery recycling center for proper battery disposal information A CAUTION The remote control device complies with part 15 of the FCC rules Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment Abo NOT put Maestro ina damp place or where humidity is high Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation NOTE For Optimal Performance Place the Maestro at least 5 away from all wireless devices 17 45049 01 07 13 09 Hunter Fan Company 11 Operating the Remote Control Light Speaker Light Pressing the ON OFF button on the remote once will turn the light on and pressing the button again will turn the light off MUTE A VOLUME Y Press V to decrease the brightness of the light Vv B SETUP RAEV Pressing the MUTE button on the remote once will turn the speaker on and pressing the button again will turn the speaker off A Hinter Press A to increase the VOLUME of the speaker VOLUME SOUNDOLIDER LY Press V to decrease the VOLUME of the speaker Pressing the jay will switch the surround sound function between LED Indicators R Right Chan
10. mum of 190 Watts Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation Threaded Portion of I Light Kit Light Bulbs Assembly B10 Candelabra Base 40 Watt Maximum Finial a gt Glass Bowl Steps 8 2 8 4 Breakaway Connector ab 22005 Fan Pull Chain 0 gt Pull Chain Guide Step 8 5 14 45049 01 07 13 09 Hunter Fan Company 9 1 9 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan 9 2 The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off 9 3 9 4 9 5 e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accum
11. nel A Press A to increase the brightness of the light LIGHT Speaker L Left Channel M Mixed Channel SOUNDOLIDER LED Indicators 18 45049 01 07 13 09 Hunter Fan Company 12 Changing the channel on the Maestro and the Fan A NOTE The Maestro transmitter and the fan must be on the Maestro same channel to transmit and receive properly 12 1 To change the channel on the Maestro slide the channel selection switch on the lower right corner of the transmitter 12 2 To change the channel on the fan press the button on the remote 12 3 The green red LED indicators on the bottom of the fan display the channel the fan is tuned to Green LEDs indicate a good signal and red LEDs indicate no signal Channel Selection Switch LED Indicators amp Channel 1 amp Channel 2 Ls cv FQ amp Channel 3 Channel 4 19 45049 01 07 13 09 Hunter Fan Company channel 1234 13 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Probl
12. ntil tight For all these connections use the wire connectors provided Connect the bare or green ground wire grounding from the ceiling to the green ground wire grounding from the ceiling plate and the green ground wire grounding from the fan Connect the white wire grounded from the ceiling to the white wire grounded from the fan Connect the remaining wires as follows Dual Switch Wiring e The black wire ungrounded from the ceiling to the black wire ungrounded from the fan e The black white wire ungrounded from the fan to the wire ungrounded for the wall switch Single Switch Wiring e The black wire ungrounded from the ceiling to the black ungrounded and the black white wire ungrounded from the fan A CAUTION Be sure no bare wire or wire strands are visible after making connections Turn the wire connectors upward and push them carefully back through the ceiling plate into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box lt 7 gt mic ZE _ j UI Wire Connector 45049 01 07 13 09 Hunter Fan Company 5 1 5 2 5 3 5 4 5 Installing the Canopy and Canopy Trim Ring Partially install two canopy screws about 2 full turns in the hanger bracket
13. om of the lower switch housing with the screw holes on top of the light kit speaker assembly making sure the pull chain lines up with the chain guide Attach the light kit speaker assembly to the lower switch housing by installing the two 6 32 round head screws Install the nut and washer onto the threaded rod from the light kit speaker assembly 7 10 Remove the wire connectors from the two wires in the switch housing labeled Connect Light Here or For Light Use Steps 7 8 7 9 Housing Threaded Rod Light Kit Speaker Steps 7 5 7 6 Note Align the fan pull chain with the chain guide 45049 01 07 13 09 Hunter Fan Company 7 Light Speaker Assembly Installation Continued 7 11 To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight Connect the black wire with a white stripe from the lower switch housing to the black wire from the light kit Connect the white wire from the lower switch housing to the white wire from the light kit speaker Secure all wire connections using wire connectors 7 12 To attach the lower switch housing assembly to the fan partially install two housing assembly screws into the upper switch housing 7 13 Connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug c
14. onnectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product 7 14 Align the notches in the sides of the lower switch housing with the screws on the upper switch housing Twist the lower switch housing and the light kit speaker assembly clockwise to lock the screws in place 7 15 Install the third housing assembly screw 7 16 Tighten all three screws securely Housing Assembly Screw Step 7 11 Wire ae Connections Housing Assembly Screw Housing 45049 01 07 13 09 Hunter Fan Company 8 eGlass Installation Installing the Glass Bowl 8 1 Remove protective foam ring from threaded portion of light kit speaker assembly 8 2 Install B10 candelabra bulbs 40 Watt Maximum into the sockets 8 3 Place the glass bowl over the light kit speaker assembly ensuring the threaded portion of the light kit assembly comes out of the bottom of the glass bowl 8 4 Place the finial over the threaded portion of the light kit speaker assembly and twist it as shown to tighten it against the glass bowl 8 5 Thread the fan pull chain through the pull chain guide Note In compliance with US federal energy regulations this ceiling fan contains a device that restricts the light kit to a maxi
15. ounting screw then securely tighten both mounting screws Blade Assembly Use with grommet screws Use without grommet Blade Mounting Screw 10 45049 01 07 13 09 Hunter Fan Company 7 Light Speaker Assembly Installation 7 1 To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate 7 2 Feed the upper plug connector through the center opening of the housing 7 3 Align the keyhole slots in the housing with the housing assembly screws 7 4 Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots Install the remaining screw into the housing Tighten all three screws firmly A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing Steps 7 1 7 4 fixture falling Housing Assembly Upper Screw Switch Housing I 45049 01 07 13 09 Hunter Fan Company 7 5 7 6 Jefa 7 8 7 9 7 Light Speaker Assembly Installation Continued Feed the two wires from the light kit up through the center hole in the lower switch housing Insert the threaded rod from the light kit speaker assembly into the center hole in the lower switch housing Align the screw holes in the bott
16. r s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angled mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Support Brace Low Profile ad Mounting Style Outlet Box Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high 3 45049 01 07 13 09 Hunter Fan Company A CAUTION To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screw
17. s e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 In Canada call 1 866 268 1936 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped 45049 01 07 13 09 Hunter Fan Company 2 2 2 3 2 4 2 Installing the Hanger Bracket Drill two pilot holes into the wood support structure through the
18. ulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan 15 Reversing Switch Pm In warm weather use downward air flow pattern In cold weather use upward air flow pattern 45049 01 07 13 09 Hunter Fan Company gt 10 Installation and Setup of Maestro and Remote To accommodate different audio systems and devices the Maestro can be installed in one of two ways You can choose to install the Maestro with 3 5mm Stereo Cable or you can install it with Speaker Wire Considering Optional Accessories Consider using Soundolier s optional accessories which include Wireless Subwoofers and Duo Lamps Optional accessories can be purchased through Authorized Hunter Dealers a mmn Stereo able Inceallacen For quiet and optimum performance of your Hunter fan use only Hunter speed controls SPEAKERS 0 0 000 SURROUND l 1
Download Pdf Manuals
Related Search