Samsung SCD-2080B
Contents
1. through screws at the side of the main body refer to the Figure 2 on page 11 1 You can adjust camera to any direction by using Pan Tilt Rotate mechanism e Pan Base moves by 176 to each side direction and 352 on the whole e Tilt Base covers total 73 angle 0 73 e Rotate Base moves by 174 to each side direction and 348 on the whole 2 Methods of adjustment e The case of wall installation After mounting the camera on a wall adjusting the panning angle so that the camera can face the direction to monitor when tilted Adjust the tilting angle by rotating the tilt base Loosen the rotate base hold screw and adjust rotate base for the best view Tighten the rotate base hold screw The case of ceiling installation After mounting the camera on a ceiling adjusting the panning angle to the correct viewing position by rotating the pan base Adjust the tilting angle by rotating the tilt base Loosen the rotate base hold screw and adjust rotate base for the best view Tighten the rotate base hold screw Connect the Video Output jack to the VIDEO IN jack of monitor Kg Monitor e As the connecting method varies with the instruments refer to the manual supplied with the instrument e If necessary you can connect the monitor to the REMOTE jack on the back of your camera Only connect the cable when the power is turned off Connect the adaptor to the power input terminal as shown2. RESET Resets the camera settings to the factory defaults Language and Monitor settings are not initialized If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician e Nothing appears on the screen gt Check that the power cord and line connection between the camera and monitor are properly connected gt Check that you have properly connected BNC cable to the camera The image on the screen is dim Is the lens stained with dirt Clean your lens with soft clean cloth gt Set the monitor to the proper condition gt If the camera is exposed to very strong light change the camera position The image on the screen is dark gt Adjust the contrast feature of the monitor gt If you have an intermediate device set the 750 Hi z properly e The camera is not working properly and the surface of the camera is hot b Check that you have properly connected the camera to an appropriate power source e The SENS UP function does not work gt Check that AGC of EXPOSURE SETUP menu is OFF gt Check that SHUTTER of EXPOSURE SETUP menu is A FLK or MANUAL e The Motion Detection function does not work gt Check that MOTION DET of SPECIAL SETUP menu is OFF e Color is not correct gt Check the setting of WHITE BAL SETUP menu e The screen flickers continually gt Check that direction of camer
3. C5CZ6V3Z200001X 2010 02 01 EN 55022 2006 EN 50130 4 2003 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer Signature Full Name Position Place Date FT Gu BONJENG GU CHANGWON KOREA 2010 02 01 SAMSUNG TECHWIN CO LTD QUALITY CONTROL MANAGER Legal Representative in Europe Signature Full Name Position Place Date SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon 1 dong Jungwon gu Seongnam si Gyeonggi do Korea 462 703 TEL 82 31 740 8151 8 FAX 82 31 740 8145 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Tol Free 1 877 213 1222 FAX 1 310 632 2195 Park Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungsecurity com P No 26806 1138 01A VAN 10 02
4. High Resolution Varifocal Dome Camera SCD 2080 User Guide Before installing and operating this product please read this manual thoroughly ENGLISH Before operating the camera confirm the camera model and correct input power voltage To help you understand this manual thoroughly we ll introduce our model description SCD 2080 SERIES e NTSC MODEL e PAL MODEL SCD 2080N SCD 2080P E MODEL DESCRIPTION SCD 2080X L SIGNAL SYSTEM e SIGNAL SYSTEM N NTSC MODEL P PAL MODEL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is A intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment i
5. PRIVACY 2 Set up the mode using the Function Setup switch AREA You can select up to 12 PRIVACY areas MODE Determines whether to use the area selected in the AREA MASK COLOR Determine area color You can select Green Red Blue Black White Gray MASKTONE Adjust the brightness of MASK COLOR TOP BOTTOM LEFT RIGHT Adjust the size and position of the selected area RETURN Select this to save the PRIVACY menu settings and return to the SPECIAL menu DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind e As the DIS function uses the digital zoom the camera s resolution will decrease e DIS doesn t operate when background illumination is too low DIS doesn t operate when object pattern is monotonic as like sky or white wall LANGUAGE You can select the menu language according to your requirements NTSC Korean English French Spanish Japanese Portuguese Taiwanese PAL English Chinese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese RETURN Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu Select a desired EXIT mode using the Function Setup switch depending on the camera purpose SAVE Save the current settings and exit the MAIN SETUP menu NOT SAVE Do not save the current settings and exit the MAIN SETUP menu
6. and select the letter by pressing the Function Setup switch Repeat this to enter multiple letters You can enter up to 15 letters 5 Enter a title move the cursor to POS and press E the Function Setup switch The entered title FRONT DOOR appears on the screen Select the position to S display the title on the screen by using the HAN Function Setup switch and press the Function Setup switch When the position is determined select END and press the Function Setup switch to return to the SPECIAL menu e When the CAM TITLE menu is OFF no title will be displayed on the monitor screen even if you enter one e Only English is available in this mode e f you move the cursor to CLR and press the Function Setup switch all the letters are deleted To edit a letter change the cursor to the bottom left arrow and press the Function Setup switch Move the cursor over the letter to be edited move the cursor to the letter to be inserted and then press the Function Setup switch SYNC In areas where the supply is at 60Hz NTSC 50Hz PAL you can synchronize the output phase of multiple cameras using the power synchronization function Line Lock without using a synchronization signal generator INT Internal Synchronization Type UL Power Synchronization Type Line lock e Press the Function Setup switch e You can select a desired phase from 0 to 359 when select phase e When using AC po
7. in the figure below The recommended adaptor specification for SCD 2080N SCD 2080P is DC 12V 500mA or AC 24V 300mA Power Input Terminal As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera Standard voltage for camera operation DC 12V 10 AC 24V 10 There may be some deviation in voltage drop depending on the type of wire and the manufacturer Notes e Be sure to connect power only after all the installation is complete e Note that AC DC adaptor is not supplied with camera e Ground should be connected to the GND terminal BRIGHTNESS SHUTTER AGC e Coaxial Communications System EYES Pan CONTROLLER SENS UP RETURN OSD Control method UP KEY JOYSTICK UP DOWN KEY JOYSTICK DOWN ATW OUTDOOR INDOOR LEFT KEY JOYSTICK LEFT RIGHT KEY JOYSTICK RIGHT MANUAL AWC SET SSDR 0FF ON Ome E BACKLIGHT 0FF BLC SSNR3 0FF 0N m DAY NIGHT COLOR eB W AUTO es IMAGEADJ MONITOR CAMTITLE SPECIAL SYNC MOTION DET PRIVACY Video Cable The camera s video output port is connected to the monitor with a BNC coaxial bi ee ene cable shown below If the distance between the camera and the monitor EXIT SAVE NOT SAVE RESET
8. a turns toward the Sun e When coaxial communication is not available gt Make sure that the camera and monitor are installed within the recommended distance gt Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded Input Voltage DC 12V AC 24V Imaging Device 1 3 inch Diagonal 6mm Super HAD CCD Total Pixels 811 H x 508 V 795 H x 596 V Effective Pixels 768 H x 494M 752 H x 5820 Scanning System 2 1 Interlace Synchronization Internal Line Lock Frequency H 15 734KHz V 59 94Hz H 15 625KHz V 50 00Hz Horizontal Resolution COLOR 600TVL B W 700TVL Min Illumination COLOR 0 15 Lux 50IRE F1 2 0 0003Lux SENS UP x512 B W 0 001Lux 50IRE F1 2 0 000002Lux SENS UP x512 SIN Y Signal 524B Weight On AGC Off Video Output Zoom Ratio CVBS 1 0Vp p 7522 composite 3 6x Manual Focus Length 2 8 10 0mm F1 2 Angular Field of View Pan Tilt Rotate Range Electronic Shutter Speed Tele 28 H x 212 Wide 94 4 H x 69 220 0 352 0 73 0 348 1 60 1 120k sec 1 50 1 120k sec ON Screen Display NTSC Korean English Japanese Spanish French Portuguese Taiwanese PAL English Chinese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese SSDR On Off L
9. according to the picture display you want COLOR The picture is always displayed in color B W The picture is always displayed in black and white You can turn on or off the burst signal on BAW mode QAUTO The mode is switched to Color in a normal environment but switches to B W mode when ambient illumination is low To set up the switching time for AUTO mode press the Function Setup switch You can turn on or off the burst signal on B W mode DURATION You can select the day night switching point DWELL TIME You can select the duration time about changing the day night mode 3s 5s 75 10s 15s 20s 30s 40 60s Color B W B W gt Color Early 2 5 lux 5 lux The day night switching point of the Late 1 lux 10 lux camera can be adjusted Notes e When AGC in the EXPOSURE menu is OFF mode operates as selecting COLOR mode and AUTO mode cannot be selected 1 When the SETUP menu screen is displayed select SPECIAL by using the Function Setup switch so that the arrow indicates SPECIAL gt 3 5PECTA 2 Select a desired mode using the Function Setup switch 1 IMAGE ADJ IMAGE ADJ 1 When the SPECIAL menu screen is displayed select IMAGE ADJ by using the Function Setup switch so that the arrow indicates IMAGE ADJ 2 Select a desired mode using the Function Setup switch bi U REN V REV You can flip the picture vertical
10. but the greater the noise OFF Deactivates the AGC function LOW Allows automatic gain control from 5 3dB to 32dB HIGH Allows automatic gain control from 5 3dB to 37dB SENS UP When it is night or dark the camera automatically detects the light level and maintains a clear picture if this mode is activated OFF Deactivates the SENS UP function AUTO Activates the SENS UP function elf you set the Function Setup switch to AUTO mode You can adjust the brightness by increasing or decreasing the shutter speed x2 x512 e Note that the higher the zoom level the brighter the screen but the more likely it is that an after image will appear Although Noise Spots and Whitish symptoms may occur in SENS UP operation when the zoom level is increased this is normal RETURN Select this to save the changes in the EXPOSURE menu and return to the SETUP menu Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select White Bal by using the Function Setup switch so that the arrow indicates White Bal 2 Select a desired mode using the Function Setup switch gt S WHITE BAL X Select one of the following 5 modes as appropriate for your purpose QATW Select this when the color temperature is between 1 700 K and 11 000 K OUTDOOR Select this when the color temperature is between 1 700 K and 11 000 K sodium light inclusio
11. cus correctly you must activate the Focus Settings mode To activate the Focus Settings mode adjust the lens focus and then deactivate the settings mode You can adjust the shutter value of ESC shutter mode D gt 2 EXPOSURE 1 When the SETUP menu screen is displayed select EXPOSURE by using the Function Setup switch so that the arrow indicates EXPOSURE 2 Select a desired mode using the Function Setup switch BRIGHTNESS Adjusts the video brightness gt 1 BRIGHTHESS SHUTTER You can select the shutter A FLK Select this when you experience picture flicker this happens when there is a clash with the installed lighting frequency ESC Select this to control the shutter speed automatically If ESC is selected the shutter speed is automatically controlled depending on the ambient illumination of the subject MANUAL You can control shutter speed manually NTSC MODEL 1 60 1 120 000 PAL MODEL 1 50 1 120 000 Shutter speed is fixed at 1 60sec 1 50sec Set the shutter mode to if color rolling occurs e When the SHUTTER is set to ESC after selecting the Internal Synchronization Type the picture may become unstable if the camera faces a bright fluorescent light Therefore take care when choosing the installation position e When the SHUTTER is set to MANUAL or A FLK mode SENS UP will be disabled AGC AUTO GAIN CONTROL The higher the gain level the brighter the screen
12. ent at all product manufacturing C stages to preserve the environment and is taking a number of steps to provide a customers with more environment friendly products The Eco mark represents eco Samsung Techwin s will to create environment friendly products and indicates RoHS compliant that the product satisfies the EU RoHS Directive L Warnings amp Cautions This information is provided to ensure your safety and to prevent any losses financial or otherwise Please read it carefully and use the product accordingly For product inquiries please contact the retail shop where you bought the camera The use of equipment such as an aerial ladder while providing after sales service shall be at your expense Separate the power plug during a thunder storm This product is support equipment for surveillance system Therefore we can t compensate for material loss and or personal injuries by robbery fire natural disaster or other such events Warning Attention Special Mark Messages Ignoring this information may z 5 Ignoring this information may result in material loss and or gt E inten ee 5 result in material loss and or a serious personal injuries including death slight injuries Indicates Never Allowed Indicates No Disassembling Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection s
13. evel adjustable Backlight Compensation BLC HLC OFF Day 8 Night COLOR BW AUTO ICR Type Gain Control Low High Off White Balance ATW Outdoor Indoor Manual AWC 1 700 K 11 000 K SENS UP frame Integration Auto Off Selectable x2 x512 Motion Detection On Off 8 Programmable zones Privacy Masking On Off 12 Programmable zones 3D Noise Filter SSNRIII On Off Level adjustable Digital Zoom On Off x1 x16 Digital Image Stabilization DIS On Off Camera Title On Off Displayed 15 Characters Sharpness On Off Level adjustable Flip Mirror On Off _Communication Operating Temperature Humidity CoanialiFekeo Coaxtiran 10 C 50 C 30 80 RH ature Humidity ee 10 C 20 90 RH 8 x 92 7 Hmm 3459 X The specification for this product may change without prior notice for product improvement DECLARATION OF CONFORMITY Application of Council Directive s Manufacturer s Name Manufacturer s Address European Representative Name European Representative Address Equipment Type Environment Model Name Beginning Serial NO Year of Manufacture Conformance to 2004 108 EC SAMSUNG TECHWIN CO LTD SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 CCTV Camera SCD 2080P
14. exceeds the recommended maximum please use an auxiliary video amp Distance Recommended Cable Specification 300m 3C2V RG 59 U 450m 5C2V RG 6 U 600m 7C2V RG 11 U Notes e It is recommended that pure copper coax cable is used and not copper coated steel as this will cause issues with the communication over the coaxial cable Use the Function Setup switch within the camera Function Setup switch 1 Press the Function Setup switch e Main setup menu is displayed on the monitor screen Select the function using 1 LENS Change the status using the Function Setup switch the Function Setup switch 2 Select a desired function using the Function Setup switch e Place the cursor over a desired item 3 Set up a selected item by using the Function Setup switch 4 To finish the setting select EXIT and press the Function Setup switch e An item with the icon also has sub menus To select a sub menu select an item with the icon and press the Function Setup switch e An item with the icon is unavailable due to function settings Using this function you can control the screen brightness 1 When the SETUP menu screen is displayed select LENS by using the Function Setup switch so that the arrow indicates LENS gt i LEHS 2 The Lens mode has sub menu site as listed below BRIGHTNESS Adjusts the video brightness FOCUSADJ To adjust the lens fo
15. ght area in the screen optimize the installation angle for the best HLC performance e When dark the HLC is only activated when a bright light exceeding a specific size In NIGHT ONLY mode The HLC is not activated in day light or when bright light is not present at night In NIGHT ONLY mode e When HLC function is used D Z00M and DIS functions are not activated This function reduces the background noise in a low luminance environment 1 When the SETUP menu screen is displayed select SSNR3 by using the Function Setup switch so that the arrow indicates SSNR3 P 5 55NR3 2 Select a desired mode using the Function Setup switch OFF Deactivates SSNR3 Noise is not reduced ON Activates SSNR3 so that noise is reduced 3 Set the SSNR3 mode to ON and press the Function Setup switch Then you can adjust the noise reduction level You cannot set the SSNR3 to ON or OFF when the AGC mode of the EXPOSURE menu is OFF e When adjusting the noise reduction level in the SSNR3 mode remember that the higher the level set the more the noise level will be reduced as will the brightness of the image You can display pictures in color or in black and white 1 When the SETUP menu screen is displayed select DAY NIGHT by using the Function Setup switch so that the arrow indicates DAY NIGHT gt 7 08 HIGHT AUTO 2 Select a desired mode using the Function Setup switch
16. install the dome cover on the camera body turn the latches in locking direction Ceiling bracket as shown in the figure 1 An arrow for installing directions 1 Hold the ceiling bracket located where the arrow points to and separate it from the main body of the camera by rotating it anti clockwise refer to the picture in Notes on page 10 2 Place the separated ceiling bracket so that the Front side faces the area to be monitored and install it with the M4 tapping screws 3 To combine the main body with the ceiling bracket Madla M4 tapping make sure that the pan base fixation screw face the screw provided opposite side of the Front side of the ceiling bracket and rotate it clockwise 4 Adjust the camera lens to face the area to be monitored and fix the main body and the dome cover by aligning the grooves and rotating the body clockwise aaa Locking Unlocking direction Locking direction direction Anti clockwise Clockwise direction Dome cover MA tappi ping Notes N screw e The installation should be done by qualified Figure 2 service personnel or system installers e If the ceiling material is not strong enough to hold the installation screws the camera may fall off Reinforce the ceiling as needed j e To change the position of the cable take J Notes away eee Cover ond pai he canle A e Ifyou want to install the camera with the ceiling bracket combined fix it using two M4 tapping
17. ional cameras the SCD 2080 is designed so that it delivers a distinctive subject and background at the same time even when the subject is in backlight by adopting a function of the proprietary W V DSP chip 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Function Setup switch so that the arrow indicates BACKLIGHT gt 5 BACKLIGHT 2 Select a desired mode using the Function Setup switch depending on the camera purpose BLC Enables a user to select a desired area on a picture and view that area more clearly LEVEL Adjust level of the BLC function TOP BOTTOM LEFT RIGHT Adjust the area to be enhanced HLC High Light Compensation If the scene contains extremely bright light areas such as from car headlight the light can mask out much of the on screen detail LEVEL Adjust level of the HLC function LIMIT Enable to change the operating condition MASK COLOR TONE Change the color brightness of the masking area Black Red Blue Cyan Magenta TOP BOTTOM LEFT RIGHT Adjust the area to be enhanced OFF Not being used 3 Select a desired mode using the Function Setup switch Select BLC to adjust the area tobe HLC Enable the user to change the level enhanced then adjust the level limit mask color tone and area Press SET to Return Because there can be a difference in the effectiveness of HLC according to the amount of li
18. ly on the screen e H REV You can flip the picture horizontally on the screen D ZOOM You can use a digital zoom of x1 x16 e FONT COLOR You can change the OSD font color White Yellow Green Red Blue e SHARPNESS As you increase this value the picture outline becomes stronger and clearer Adjust this value appropriately depending on the sharpness of the picture e RETURN Select this to save the settings for the IMAGE ADJ menu and to return to the SPECIAL menu e When the V REV or H REV mode is enabled the text on the screen does not flip If you increase the SHARPNESS level too high the picture may become distorted or noise may appear Monitor Please change the settings value of video appropriate to your monitor LCD Please select this menu item when using an LCD monitor You can change the gamma PED level and color gain in the sub menus CRT Please select this menu item when using a CRT monitor USER Please use this menu item when using a monitor other than standard ones You can change the gamma PED level and color gain in the sub menus CAMTITLE If you enter a title the title will appear on the monitor 1 If the SPECIAL menu screen is displayed use the Function Setup switch so that the arrow indicates CAM TITLE 2 Set it to ON by using the Function Setup switch 3 Press the Function Setup switch 4 Use the Function Setup switch to move to a desired letter
19. n INDOOR Select this when the color temperature is between 4 500 K and 8 500 K MANUAL Select this to fine tune White Balance manually Set White Balance first by using the ATW or AWC mode After that switch to MANUAL mode fine tune the White Balance and the Function Setup switch AWC SET To find the optimal luminance level for the current environment point the camera towards a sheet of white paper and press the Function Setup switch If the environment changes readjust it e White Balance may not work properly under the following conditions In this case select the AWC mode When the color temperature of the environment surrounding the subject is out of the control range e g clear sky or sunset When the ambient illumination of the subject is dim If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas gt 4 550F 1 When the SETUP menu screen is displayed select SSDR by using the Function Setup switch so that the arrow indicates SSDR 2 Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas SSDR OFF Unlike convent
20. roduces clear picture quality with a horizontal resolution of 600 TV lines in color and a horizontal resolution of 700 TV lines in B W mode llent Sensitivity NAG The built in high sensitivity COLOR CCD produces a clear image Color 0 15Lux 50IRE F1 2 0 0003LUX SENS UP x512 B W 0 001Lux 50IRE F1 2 0 000002LUX SENS UP x512 ide clear images even in dark environments Paga For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness pada DIS Digital Image Stabilizer Pga The DIS function compensates for any camera movement to produce more stable pictures DN Ng Communication oye Coaxial communication methods are supported Protocol Pelco Coaxitron yeaa y a Ilaneous Functions A A DYJA 7 HLC High Light sation SENS UP FLIP HNV REV D Z NESS and PRIVACY PAGBAON D The camera s OSD is complimented by 18 languages NTSC Korean English French Spanish Japanese Portuguese Taiwanese PAL English Chinese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese Since the camera detects motion without any additional external sensor you can monitor activity more efficient Samsung Techwin cares for the environm
21. s operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes e Features J i JS e Precautions High Resolution cs Super Dynamic Range Components and Accessories e Overview e Installation E Installation E Adjust the panning tilting and rotating while watching the monitor e Connection E Connecting to Monitor E Connecting to Power E Using Coaxial Communications e Operating your Camera E Menu Configuration E Menu Setup EXPOSURE WHITE BALANCE SSDR BACKLIGHT DAY NIGHT fesse e Troubleshooting e Specification e Dimension Ppa By adopting a diagonal 6mm 1 3 410 000 NTSC pixel 470 000 PAL pixel SONY CCD the camera p
22. to smear it with fingerprints Never keep the camera face to strong light directly May damage the CCD COLOR DOME CAMERA D User Guide PIN D If exposed to radioactivity the CCD will fail May cause a product malfunction Wipe dry any liquids Liquids may contain minerals that are corrosive to electronic components Notes e Exposure to a spotlight or an object emitting strong light may cause smear or blooming e Ensure that the power source complies with normal specifications before supplying it to the camera T bh 4 oe scn 2080 Instruction Manual M4 Tapping Screw 3EA Installation Video Output Cable Pan Base Control panning angle of camera Rotate Base Control rotating angle of camera x3 6 Vari focal Lens Module 2 8 10 0mm F1 2 Video Output Terminal to Monitor Function Setup switch Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item Video Output Jack Power Input Terminal Dome Cover Shield Case e The installation should be done by qualified service personnel or sysytem installers e If the ceiling material is not strong enough to hold the installation screws the camera may fall off Reinforce the ceiling as needed 1 Separate the dome cover by turning anti clockwise When using the Ceiling bracket 2 Separate the shield case by pulling from the camera body To
23. wer at 60Hz NTSC 50Hz PAL frequency you can use the L L type synchronization e When the power is DC 12V the SYNC menu is fixed to the INT mode MOTION DET This product has a feature that allows you to observe movement of objects in 8 different areas on the screen and the words MOTION DETECTED appear on the screen when movement is detected You can monitor activity more efficient 1 When the SPECIAL menu screen is displayed press the Function Setup switch so that the arrow indicates MOTION DET 2 Set up the mode using the Function Setup switch SENSITIVITY You can select up to 8 MD areas When SENSITIVITY number is high motion detection sensitivity is increased to recognize even small movement AREA MODE Determines whether to use the MD area selected in SENSITIVITY SEL POS Determines which of the 4 vertices of each MD area is to be used XPOS Determines the coordinate of the horizontal axis for SEL POS YPOS Determines the coordinate of the vertical axis for SEL POS FILL SET Fills in a selected MD area The color of filling is sequentially selected as brown orange blue cyan green yellow magenta and red RETURN Select this to save the MOTION DET menu settings and return to the SPECIAL menu PRIVACY Mask an area you want to hide on the screen AREAL 1 When the SPECIAL menu screen is displayed press the Function Setup switch so that the arrow indicates
24. ystems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal COLOR DOME CAMERA 6 User Guide Do not install under extreme temperature conditions Use only under temperature conditions between 10 C and 50 C Provide good ventilation when using in high temperature conditions Do not install under unstable lighting conditions Pa FAN l Severe lighting changes or flickering may hinder normal camera operation Do not drop the camera or subject it to physical shock y a May cause a product malfunction Q Precautions Do not install in high humidity environment May lower image quality Avoid touching the camera lens The lens is the most important component of the camera Be careful not
Download Pdf Manuals
Related Search