DeLonghi EC 850.M
Contents
1. y 3 Functioning lights en lights Operation Meaningoflights Turn on from general ON OFF switch at the back of the appliance The appliance performs a self test signalled by the sequential flashing of lights The appliance is on no accessory is The appliance is heating up to make connected to coupling coffee when the 1 or 2 cup lights stop 7 Y flashing the appliance has reached the 4 ideal temperature to deliver coffee SI i amp The appliance is the hot water spout The appliance is heating up to make D7 is connected to coupling coffee or to deliver hot water when the 9 T 2 cup lights and the hot water spout light stop flashing the appliance has o 9 reached the ideal temperature to deliver coffee or hot water gg a WH o e The appliance is on the milk container is connected to coupling The appliance is heating up to make coffee cappuccino or latte macchiato when the 1 or 2 cup lights the cappuccino and latte macchiato lights stop flashing the appliance has reached ideal temperature to deliver coffee or cappuccino or latte macchiato The appliance has been unused for 75 minutes for the ON STAND BY button has been pressed The appliance is in STAND BY to switch it back on press the Qo Thetime inter2. Make sure that the electric mains voltage corresponds with that indicated on the data plate on the base ofthe appliance Insert the power supply cable connector in the socket on the back ofthe appliance fig 1 then insert the plug in the power outlet Check that the mains power supply voltage corresponds to the value indicated on the rating plate on the bottom of the appliance If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified professional Activation of the water filter and filling of the water tank Remove the filter from the packaging and rinse it with about 0 5 of running water fig 2 Turn the calendar disc see fig 3 until the following 2 months of use are displayed Please note the filter has a two month duration if the appliance is used normally whereas if the machine remains unused with the filter installed it has a maximum 3 month duration Remove the water tank and fill it with fresh water do not exceed the MAX line fig 4 Completely dip the filter in the water tilting it to enable air bubbles to come out fig 5 Insert the filter in the appropriate seat fig 6 press down and dose the tank with the lid Place the tank back into the machine Ensure the water level is not over the MAX line fig 7 Instructions for usery The filter is now activated and the machine can be used Appliance first use Turn the appliance on
3. Directives Stand by Directive 1275 2008 Low Voltage Directive 2006 95 CE and successive amendments EMC Directive 2004 108 CE and successive amendments The materials and objects destined to come into contact with food stuffs are in compliance with the provisions of the 1935 2004 European Standard Disposal WX Recommendations forthe correct disposal ofthe product in compliance with the 2002 96 CE European Directive wmm and Legislative Decree n 151 dated 25 July 2005 The product must not be disposed of as urban waste at the end ofits working life It must be taken to appropriate local authority separate waste collection centres or to dealers providing this service Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from unsuitable disposal and allows to recover the materials of which it is made in order to make significant savings of energy and resources The product has the crossed out wheeled bin mark as a reminder ofthe obligation to dispose of household appliances separately The illegal disposal of the product by the user entails the application of administrative sanctions envisioned by the Standard in force 13 Disposal g Troubleshooting ry Problem Possible causes Solution The device will not switch on The power supply cable is not inserted correctly Check that the power supply cable connector is fully inserted in the appropri
4. by default to deliver standard amounts If wanting to amend these quantities proceed as follows 1 Place a cup under the spouts of the coffee spout and under the milk spout tube 2 Press the button relative to the preparation with milk to be programmed and keep it pressed After a few seconds the machine starts delivering the milk 3 As soon as the wanted amount of milk in cup is reached release the button milk delivery stops 11 Instructions for user 4 Program the amount of coffee in cup as for the amount of milk 5 Programming is confirmed by the lights flashing for 3 seconds The machine is now re programmed according to the new amounts of milk and coffee Preparing the hot water A Scalding hazard Do not leave the machine unattended when delivering hot water The spout heats up during delivery therefore only the black part must be held 1 Check the hot water spout is correctly attached fig 8 2 Place a cup under the spout as near as possible to avoid sprays 3 Press the button fig 2 the relative light flashes and the appliance starts hot water delivery The machine automatically stops delivery Please note To manually interrupt the hot water delivery press button again Programming the amount of water automatically delivered If wanting to amend the set by default amount proceed as follows 1 Place a cup under the spout 2 Keep the button pressed 3 When the h
5. by pressing the 1 0 main switch at rear in pos I the appliance performs a self test signalled by the sequential flashing of the lights Once the self test is completed the hot water spout light B8 flashes while the others turn off the appliance signals it is necessary to insert the hot water spout fig 8 Place a container underneath the spout with minimum capacity of 100 ml fig 9 _ Press the hot water button delivery starts and interrupts automatically ind The coffee and water spout lights flash to indicate the appliance is reaching temperature when the lights stop flashing and remain permanently on the appliance is ready for use Please note upon first use B If lights Q and flash press the button again Upon first use it is necessary to make 4 5 coffees or 4 5 cappuccinos before the machine gives a satisfying result Settings of the programming menu To access the menu ensure the appliance is in stand by simultaneously press buttons and until the ON Standby light flashes the appliance is in programming mode Set the machine as wanted to exit the programming menu press button again Setting the temperature If wanting to modify the water temperature with which coffee is delivered proceed as follows 1 Access the programming menu 2 Keep button pressed until the lights relative to the wanted temperature turn on Medium temperature High temperature
6. inserted 4 Simultaneously press the and buttons light 8 turns on if the hot water spout has not been inserted the light flashes 5 Press the button Descaling is signalled by the LED that alternate in sequence The descaling program automatically performs a series of deliveries from the boiler outlet and from the hot water spout at intervals to remove the lime scale from inside the coffee machine 6 the descaling solution is terminated the light turns on to indicate rinsing is necessary 7 Toeliminate the solution and lime scale residues rinse the tank and fill it with fresh water without descaler empty the containers and place them under the boiler outlet and hot water spout 8 Pressthe button rinsing starts and all LEDs flash in sequence 9 Rinsing stops when the tank is empty rinse and top up the tank 10 Light on press the relative button delivery starts an interrupts automatically The appliance is now ready for use Repairs to the coffee machine relative to lime scale problems are not covered by the warranty if the descaling procedure described above is not performed on a regular basis Technical data Mains voltage 220 240V 50 60Hz Absorbed power 1450W Sizes LxHxD 305x275x320 mm Thermoblock Stainless steel Aluminium Pressure 15 bar Water tank capacity 1L Power supply cable length 12m Weight 7 kg C The appliance is in compliance with the following CE
7. 3 When the lights relative to the desired selection turn on release the button 4 Press to turn the appliance off stand by Low temperature Set the water hardness The lights signalling the need to descale the appliance after a pre set period of operation that depends on the hardness of the water It is possible to program the machine according to the actual water hardness in use in the area thus making descaling less frequent Proceed as follows 1 Remove the provided reactive strip TOTAL HARDNESS TEST from its packaging 2 Completely dip the strip into a glass of water for one second 3 Remove the strip from the water and shake it slightly After about one minute 1 2 3 or 4 red squares form depending on the hardness of the water 4 red squares very hard water Access the programming menu 5 Onceobtained the result of the strip keep the hot water button pressed until the lights turn on as in following table C ROD eo mum uuum 3 G8 5 When the lights relative to the detected water hardness turn on release the button 6 Press button to turn the appliance off stand by i Please note If the water filter is correctly used set the machine on to a lower hardness level compared to that detected by the reactive strip ON OFF and stand by When the main swit
8. De Longhi Appliances via Seitz 47 31100 Treviso Italia 5713215741011 850 Instructions for use COFFEE MAKER Milk frother lid with froth regulator Milk intake Filter holder cu Milk container Crema filter 1 coffee SZ Crema filter NS 2 coffee Power supply Measuring spoon cable removable tamper Crema filter ESE pods Reactive strip to detect water hardness Total hardness test Removable water spout i TT Lu Water softener filter Cup shelf Control panel see description below Boiler outlet Infusion assembly General switch Water tank seat ON OFF Power supply cable t connector Water tank lid Sliding tray 2 for long coffee latte macchiato E glass Indicator for 5 mem drip tray water filter seat water level 2 Drip tray Water low level indicator ON Stand by Button qun Hot water light cup temperature Hot milk OK light cappuccino button Hot milk a fom 2 cups temperature latte macchiato Hot milk _ OK light temperature latte macchiato button OK light Hot milk cappuccino temperature OK light pae
9. ate socket on the back of the device then check that the plug is correctly connected to the power outlet Espresso coffee does not flow out No water in the tank Fill the water tank The holes in the filter holder are blocked Clean the holes in the filter holder spouts The espresso boiler outlet is blocked Clean as indicated in the Cleaning paragraph Espresso coffee drips from the edges of the filter holder instead of through the holes The filter holder is not correctly inserted or is dirty Attach the filter holder correctly and turn it fully home firmly The espresso boiler gasket has lost elasticity or it is dirty The holes in the filter holder spout are blocked Replace the espresso boiler gasket at an After Sales Centre Clean the holes in the spouts The filter holder does not hook onto the device Too much coffee was poured in the filter Use the measure provided and make sure to use the correct filter for the type of preparation desired Loud pump noise The water tank is empty Fill the tank The tank is inserted incorrectly and the valve on the bottom is not open Press the tank lightly to open the valve on the bottom The coffee cream is clear it flows quickly from the spout The ground coffee has not been sufficiently pressed Increase pressing ofthe ground coffee Not enough ground coffee Increase the amount of ground coffee The coffee is
10. ch is in pos I turn the appliance on and off Instructions for user stand by by pressing the button The appliance automatically turns off stand by after 75 minutes of non use to change the non use time refer to following paragraph Adjust Stand by The machine is pre set to switch to stand by after 75 minutes of non use This time interval can be modified so that the appliance switches off after 15 minutes or after 3 hours Proceed as follows 1 Accessthe programming menu 2 Keep the gt button pressed until the lights relative to the desired standby interval turn on 15 minutes 75 minutes 3 hours 3 When the lights relative to the wanted selection turn on release the button 4 Press Q to turn the appliance off stand by How to prepare espresso using ground coffee Insert the filter for ground coffee in the filter holder fig 10 Use the filter if wanting to make one coffee or the filter SZ if wanting to make 2 coffees To prepare one coffee fill the filter with a level measuring spoon of ground coffee about 7gr fig 11 If you wish to prepare two cups of coffee fill the filter with two less than level measuring spoons of ground coffee about 7 7 gr Fill the filter with small amounts at a time to prevent the coffee spilling out A Attention For correct use before filling the filter with ground coffee always make sure there is no residual coffee from the previous infu
11. e milk frother lid is not in correct position Ensure to have positioned the cursor in froth position The milk container lid is dirty Clean the milk lid as described in par Cleaning the milk container The machine does not deliver any drink and the lights flash for afewseonds No water in the tank Fill the water tank The tank is inserted incorrectly and the valve on the bottom is not open Press the tank lightly to open the valve on the bottom Incorrectly installed water filter Activate the filter by following the indicated procedure The ground coffee is too tightly pressed Press the coffee less The espresso boiler outlet is blocked Perform cleaning as indicated in par cleaning the boiler outlet The filter is blocked Perform cleaning as indicated in par cleaning the filter The machine does not work and all lights flash Immediately disconnect the appliance and contact an authorised after sales assistance centre 15
12. hotels motels and other reception structures guest houses Any other use must be considered improper and therefore dangerous The manufacturer is not liable for damage deriving from improper use of the appliance Instructions for use Read these instructions carefully before using the appliances Failure to respect these instructions may result in personal injury or damage to the appliance The manufacturer is not liable for damage as a result of failure to comply with these user instructions Please note Keep these instructions carefully If the appliance should be transferred to other persons these instructions must accompany it Checking the appliance After the packaging has been removed check the integrity of the appliance and the presence of all accessories Do not use the appliance if it is visibly damaged Contact the Customer Experience Installing the appliance Attention The following safety measures must be complied with when installing the appliance The appliance could be damaged by water infiltration Do not position the appliance near to water taps or sinks The appliance could be damaged if the water it contains freezes Do not install the appliance in a room where the temperature can fall below freezing point Position the power supply cable in a way that it cannot be damaged by sharp edges or by contact with hot surfaces e g electric plates Connecting the appliance Attention
13. ing delivered the frothed milk the machine automatically prepares the coffee Please note For a hotter cappuccino it is advised to press the CLEAN button to heat the ducts of the milk frother device see successive paragraph To prepare the cappuccino or the latte macchiato the appliance performs 2 deliveries first the milk and subsequently the coffee If wanting to interrupt the delivery in progress press the previously pressed button Once delivery is completed if wanting to increase the amount of milk or coffee inside the cup keep the button within a few seconds relative to the preparation in progress pressed Do not leave the milk container out of the refrigerator for too long the higher the milk temperature 5 is ideal the poorer is the quality of the froth Cleaning the milk frother device using the CLEAN button After every use of the milk functions perform cleaning to eliminate the milk residues as follows 1 Leavethe milk container inserted in the machine it is not necessary to empty the milk container 2 Place a cup or other container under the frothed milk spout tube 3 Keep the CLEAN button fig 24 pressed lights and flash When the lights stop flashing and the appliance goes back to ready for use release the CLEAN button the steam cleans the circuits inside the milk frother Program the amount of coffee and milk in the cup for cappuccino or milk The machine has been set
14. ing the milk container Clean the milk container after each milk preparation as described below 1 Extract the lid 2 Remove the milk spout tube and the intake tube fig 28 3 Remove the froth regulator by by pulling it out fig 29 Carefully clean all components using hot water and a mild detergent All components can be washed in the dishwasher by positioning them on the upper rack of the dishwasher Pay particular attention that milk residues do not remain inside the holes and in the groove on the narrow part of the froth regulator 5 Also check that the intake tube and the spout tube are not obstructed by milk residues 6 Re assemble the cursor the spout tube and the milk intake tube 7 Place the lid on the milk container again Replacing the filter After two months of duration see calendar or if the appliance is not used for 3 weeks replace the filter as described in paragraph Activation of the softener filter and filling of the tank 12 Instructions for user Descaling a Descale the machine when the light OG ashes on the control panel Proceed as follows 1 Remove the water filter Fill the tank with the descaling solution obtained by diluting the descaler with water on the basis of the indications given on the pack 2 Insert the hot water spout fig 8 3 Place one container under the boiler outlet and one under the hot water spout fig 29 and ensure the drip tray is empty and correctly
15. not ground finely enough Incorrect type of ground coffee Only use coffee ground specifically for espresso coffee machines Change the quality of the ground coffee After coffee delivery the filter remains attached to the boiler outlet Insert the filter holder again then remove it After the coffee has been prepared the pod or coffee powder remains attached to the boiler outlet Re insert the filter holder deliver coffee remove the filter holder 14 Troubleshooting ry Problem Possible causes Solution The coffee cream is dark it flows slowly from the spout The ground coffee is too tightly pressed Press the coffee less Large amount of ground coffee Decrease the amount of ground coffee The espresso boiler outlet is blocked Perform cleaning as indicated in par cleaning the boiler outlet The filter is blocked Perform cleaning as indicated in par cleaning the filter The coffee is too finely ground Only use coffee ground specifically for espresso coffee machines The ground coffee is too fine or is damp Incorrect type of ground coffee Only use coffee ground specifically for espresso coffee machines and it must not be too damp Change the quality of the ground coffee powder The milk does not froth when making a cappuccino The milk is not cold enough Always use milk at refrigerator temperature The cursor of th
16. ot water in the cup reaches the required level release the button Programming is confirmed by the lights flashing for three seconds The machine is now re programmed according to the new amount Cleaning A Attention Do not use solvents abrasive detergents or alcohol to clean the machine Only the milk container D can be washed in the dish washer No other part of the appliance can be washed in the dishwasher Do not use metal objects to remove coffee deposits or fouling as they might scratch the metal or plastic surfaces Cleaning the drip tray Attention The drip tray is equipped with a floating water level indicator red fig 24 As soon as this indicator starts protruding from the cup tray empty the tray and dean it otherwise the water may overflow and damage the machine and the surrounding work top 1 Removethe drip tray fig 25 2 Remove the cup tray dispose of the water fig 26 and dean the tray using a cloth then re assemble the drip tray 3 Re insertthe drip tray Cleaning the coffee filters Regularly clean the coffee filters rinsing them under running water Check that the holes are not blocked If they are clean them using a pin fig 27 Cleaning the boiler outlet Rinsethe boiler outlet every 200 coffees delivered by delivering 0 51 of water from the boiler outlet place a cup under the spouts and then press thebutton to deliver a coffee without using coffee powder Clean
17. s The machine is now re programmed according to the new amount How to prepare milk based drinks To avoid obtaining insufficiently frothed milk or with large bubbles always clean the lid of the milk and the hot water nozzle as described in the cleaning the milk container on page 12 1 Remove the lid fig 17 2 Fill the milk container with sufficient amount of milk not exceeding the maximum of 0 5 fig 18 Remember that every notch on the side of the container corresponds to 100 ml of milk o Please note For a more dense and homogenous froth use skimmed or partially skimmed milk at refrigerator temperature about 5 C 3 Ensure the milk intake tube is correctly inserted in appropriate seat envisioned at bottom of the milk container lid fig 19 Place the lid on the milk container again Remove the hot water spout from the nozzle Attach by inserting the container to the nozzle fig 20 Set up the machine to make coffee see par how to prepare espresso 8 Place the cup for cappuccino or the glass for Latte Macchiato under the coffee spout and arrange the milk spout fig 21 If using tall cups or glasses reposition the cup holder as shown in fig 22 9 Vary the froth regulator depending on the amount of froth wanted and type of milk used fig 23 To prepare the Cappuccino press button To prepare the latte macchiato press button 9 After hav
18. sion in the filter Distribute the ground coffee evenly and press it lightly using the coffee tamper fig 12 Pressing the ground coffee is very important to obtain a good espresso If excessively pressed the coffee will slowly leak and it will be stronger Whereas if slightly pressed the coffee will come out too quickly and will be light Remove any excess coffee from the rim ofthe filter holder and attach it to the machine for correct attachment align the filter holder handle to symbol o OPEN fig 13 attach the filter holder and turn grip to the right until aligned to position W CLOSE fig 14 Position the cup or cups under the filter holder spouts fig 15 It is advised to heat the cups before making the Coffee rinsing them with hot water Ensure the lights relative to the coffee buttons are on press the coffee buttons or the appliance proceeds and interrupts automatically How to prepare espresso using pods Please note use pods that comply with the ESE Standard this will be indicated on the packaging by the following mark The ESE Standard is a system accepted by leading coffee pod manufacturers and allows espresso coffee to be made simply and without mess Insert the filter for pods coffee in the filter holder fig 10 Insert the pod centring it as far as possible on the filter fig 16 Always follow the instructions of the pod pack for correct positioning of the pod in
19. the After Sales Technical Assistance Ifthe plug or power supply cable are damaged have them replaced exclusively by the De Longhi After Sales Service in order to avoid risks During cleaning never immerse the machine in water it is an electric appliance Before performing any cleaning operations to the external parts of the appliance switch the machine off remove the plug from the socket and let the machine cool down A Attention Keep the packaging material plastic bags expanded Safety warnings rr polystyrene out of the reach of children A Attention Do not allow the appliance to be used by persons including children with reduced psycho physical sensorial capacities or that have insufficient experience and knowledge unless they are carefully monitored and trained by a person responsible for their safety Watch children do not let them play with the appliance A Scalding hazard This appliance produces hot water and steam may form during operation Pay attention not to come into contact with hot water sprays or steam Do not touch the cup holder when the appliance is on because it can get Complying with intended use This appliance is manufactured for the preparation of coffee and to heat beverages This appliance is intended exclusively for domestic use It is not intended for the use in e rooms used as kitchens for personnel in shops offices and other work areas farm holidays e
20. the filter Attach the filter holder to the machine for correct attachment align the filter holder handle to symbol o OPEN fig 13 attach the filter holder and turn grip to the right until aligned to position W CLOSE fig 14 Position the cup under the filter holder spouts It is advised to heat the cup before making the coffee rinsing it with hot water Ensure the lights relative to the coffee buttons are on press the coffee button the appliance proceeds and interrupts automatically Please note While the machine is preparing the coffee the can be stopped at any time by pressing the previously pressed coffee button Once delivery is completed if wanting to increase the amount of coffee inside the cup keep the previously pressed 10 Instructions for user coffee button pressed within 3 seconds of delivery Turn the grip from right to left to release the filter holder A Scalding hazard To avoid sprays never release the filter holder while the machine is delivering and wait a few seconds after delivery Program the amount of coffee in the cup The machine has been set by default to deliver standard amounts If wanting to amend these quantities proceed as follows 1 Place a cup under the coffee spout 2 Keep the button to be programmed or pressed The machine starts delivering coffee 3 as the wanted amount of coffee in cup is reached release the button delivery stop
21. val before stand by is adjustable see section Adjust Stand by interval The tank is empty or the appliance cannot deliver See section If something does not work page 13 Symbols used in these instructions The important recommendations have these symbols These warnings must be followed A Danger Failure to comply can be or is the cause of injury due to life threatening electric shocks A Attention Failure to comply can be or is cause of injury or damage to the appliance A Scalding hazard Failure to comply can be or is the cause of scalding or burns i Please note This symbol highlights recommendations and important information for the user Fundamental warnings regarding safety ZN Dingen As the appliance operates using electric current electric shocks can not be excluded Therefore follow the safety recommendations given Do not touch the appliance when you have wet hands or feet Donottouch the plug with wet hands Make sure that the socket used can always be easily reached so that the plug can be removed when required Remove the plug from the socket by pulling directly on the plug itself Do not pull the cable as damage could be caused e Remove the plug from the socket to disconnect the appliance completely not attempt to repair the appliance if it should breakdown Switch the appliance off remove the plug from the socket and contact
Download Pdf Manuals
Related Search