Home

Premier AM225F, 37" - 63"

image

Contents

1. studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 AM225 4 Installation Tools The following tools may be required dependent upon your particular installation These tools are not provided by Premier Mounts but you can purchase them at your local hardware store lalz va Drill Bit for Electronic Stud Finder Wood Stud 5 16 Concrete Drill Bit Hand Held Drill Zip Ties Socket Wrench Socket M10 Socket Phillips Tip Screwdriver Optional tools for concrete installations Parts List Your Premier Mounts product is shipped with all proper
2. the M5 side screws on top of the mounting plate to allow for swivel Robust Mount Design The heavy duty wall frame ensures that your flat panel stays were you installed it Installation on Stud Placement The mounting brackets are designed to easily attach to 12 or Versatile 16 studs Use a P4263F or P4263T mount to attach the display to the AM225 Page 4 Visit the Premier Mounts website at http www premiermounts com Installation Instructions 4 AM225 24 Building the Wall Frame Use eight 8 M4 x 8mm combo Phillips screws to attach the two 2 crosspiece brackets to the two 2 wall mounting brackets Fig 1 ii Make sure the brackets are facing in the same direction as shown Fig 1 fir The screws must been inserted as shown Fig 2 and Fig 3 M4 x 8mm combo Phillips screw M4 x 8mm combo Phillips screw SS Wall Frame Bottom of Wall Frame Fig 2 Proceed to the Installing the Wall Frame section Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 5 b a SZ AM225 Installing the Wall Frame Introduction Facing the Front Make sure the flat side of the wall frame s crosspiece brackets is facing the front Mounting Safety Two people are recommended for installing this mount Determining the Mounting Surface If you will be installing your AM225 mount to wood studs proceed to the Wood Stud Installation section If you wil
3. the mounting locations Place the wall frame against the wall in the desired viewing location Level the wall frame Use a pencil and mark 2 upper and 2 lower mounting locations where you will be drilling holes for the concrete wedge anchors Each horizontal location cannot be closer than 12 apart Set the wall frame to one side in a safe location Use a power drill and 5 6 concrete drill bit to drill a hole at each of the marks Page 8 Visit the Premier Mounts website at http www premiermounts com Installation Instructions b a AM225 24 Installing the Wall Frame cont d Insert a concrete wedge anchor into each hole If necessary lightly tap each concrete wedge anchor into place with a hammer Remove the nuts and washers from all four 4 concrete wedge anchors Place the wall frame against the wall over the threaded shafts of the concrete wedge anchors Replace the washers which you removed from the concrete wedge anchors with the 4 washers shown in the parts list on Page 3 Attach the nuts and 4 washers to each of the concrete wedge anchors and tighten using a socket wrench and an M10 socket lateral shift to help you precisely position the pullout mount fo The wide mounting slots in the wall frame allow A Do not overtighten the wedge anchor nuts Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 9 gt 4 24 AM225
4. EE E ITT SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF ARME AE TANGENSI 5 S THE FLAT PANEL IF NOT THE WALL STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE STOP PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel If mounting to wall studs make sure that the mounting screws are anchored into the center of the wall
5. Installing the Pullout Mount Pre install two 2 M8 x 12mm combo Phillips screws in the top screw holes of the wall frame Fig 1 using at least 5 full turns M8 x 12mm combo Phillips screw ji 2 Leave a gap between the heads of the screws and UY the wall frame for hanging the pullout mount Hang the pullout mount on the M8 x 12mm combo screws that were pre installed in the wall frame Fig 2 Ae g The keyhole design 0 of the pullout mount s O screw holes makes hanging easier Wall Frame Fig 1 Use 2 M8 x 12mm combo Phillips screws to attach the bottom of the pullout mount to the wall frame Fig 3 Use two 2 M5 x 8mm combo Phillips screws to attach the middle of the pullout mount to the wall frame Fig 3 Tighten the top M8 x 12mm combo Phillips screws Proceed to the Attach a P Series Mount and or Accessories section Pullout Mount M5 x 8mm combo Phillips screw M8 x 12mm combo Phillips screw Page 10 Visit the Premier Mounts website at http www premiermounts com Installation Instructions AM225 Attach a P Series Mount and or Accessories Use four 4 M8 x 16mm pan Phillips screws to attach the P Series P4263F or P4263T flat panel mount to the AM225 Follow the installation instructions included with the P Series mount Make sure the P Series mount is aligned to the center of the pullout portion of the AM225 Proceed to the Post Installation A
6. djustments section AM225 with P4263F flat mount Post Installation Adjustments Remove the M5 top side screws on location A to swivel You cannot re insert the top side screws unless the mounting plate is centered ify Do not remove the M8 middle screw Use an M2 5 Allen wrench to loosen the screws on locations B to adjust the pullout tension Stop loosening when the desired tension is achieved Proceed to the Cable Routing section Back view of the AM225 pullout mount Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 11 24 AM225 Cable Routing Neatly organize cabling and wiring by Routing them through the openings in the pullout mount Using zip ties not included through the zip tie holders on the side brackets Zip tie Holders Technical Specifications All measurements are in inches mm 477 67 156 46 ees 198 63 420 7 820 J 11430 4 Page 12 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 AM225 PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchase
7. e wall frame Use a pencil to mark the remaining three 3 mounting locations along the center of each wall stud Two people are recommended for this step one person to level the wall frame and another person to drill the pilot holes Drill a pilot hole in the center of each of the marks with a power drill and a 4 drill bit A Only use drill bit when drilling the pilot holes Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 7 b a 24 AM225 Installing the Wall Frame cont d Insert one 1 4 x 3 lag bolt and one 1 54s washer into each pilot hole The wide mounting slots in the wall frame allow lateral shift to help you precisely position the pullout mount Tighten all lag bolts using a socket wrench and socket Do not overtighten the lag bolts when attaching the mount to the wall Improper installation may result in personal injury or property damage Proceed to the Installing the Mounting Bracket section Concrete Installation The supplied 5 6 concrete wedge anchors must be used for concrete installation You will need a 5 6 concrete drill bit which is available at your closest hardware store Concrete Wedge Anchors not included Example of 6 Concrete Drill Bit not Included Two people are recommended for this step one person to level the wall frame and another person to mark
8. installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts at 800 368 9700 AM225 Mount Components Pullout Mount Wall Mounting Bracket Crosspiece Bracket Qty 1 Qty 2 Qty 2 F M4 x 8mm Combo M5 x 8mm Combo M8 x 12mm Combo M8 x 16mm Combo yea Flat Washer Metal Phillips Screw Qty 8 Phillips Screw Qty 2 Phillips Screw Qty 4 Phillips Screw Qty 4 Qty 4 5 x 3 Hex Lag Bolts M2 5 Allen Wrench Qty 4 Qty 1 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 3 gt 4 22 AM225 Features The Extending Swivel Mount AM225 is the ideal wall mount for flat panels It extends smoothly up to 20 inches from the wall and allows simple post installation leveling and swivel adjustments for the perfect viewing angle Its open design makes it easy to set up cable and electrical wiring The AM225 works with the P Series P4263F or P4263T flat panel mount to help support the display Stylish Design Sleek sturdy and unobtrusive Cable Management Use zip ties and openings to keep Adjustable Extension cables from being pinched and Your flat panel stays at V reduce unsightly cable clutter the extension you choose regardless of flat panel size or weight Post Installation Adjustments Remove
9. l be installing your AM225 mount to a concrete wall proceed to the Concrete Installation section Wood Stud Installation You must secure the wall frame to two 2 wall studs with a minimum of four 4 lag bolts 2 lag bolts for each stud found Use a stud finder to determine the exact center of wall studs in the vicinity of the wall frame Use a pencil to mark the exact center of each of the wall studs Two people are recommended for this step one person to level the wall frame and another person to mark the wall stud location Place the wall frame against the wall in the desired viewing location Adjust the wall frame to align the mount slots in the wall frame with the center of the wall studs Level the wall frame Use a pencil to mark the upper right mounting location along the center of the wall stud Page 6 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 AM225 24 Installing the Wall Frame cont d Drill a pilot hole in the center of the upper right mark using a 4 drill bit and power drill A Only use a drill bit when drilling the pilot holes Place the wall frame against the wall and align it with the pilot hole Insert one 1 5 4 x 3 lag bolt and one 1 3s washer into the upper right mounting hole and tighten using a socket wrench and 2 socket A Do not overtighten the lag bolt Level th
10. oe PREMIER Cad MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Extending Swivel Mount for Flat Panels Model AM225 NORTH AMERICA EUROPE 3130 East Miraloma Avenue Unit 3 The Moorings Business Park ee pea USA Channel Way Longford and Canada To GTA AAO Coventry CV6 6RH UK Phong 1 800308 9700 Phone 44 0 24 7664 4105 Fax 1 800 832 4888 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Fax 44 0 24 7664 4165 9531 021 001 02 gt 4 E AM225 Weight Limiteen a e a E E rrr a T rere ree 2 WalMInG StAlSMONtS eS NS S ASS 2 Installation TOO Syse a A a aia 3 Pans List sannana A a snus a a aa a E a 3 Feature S asea eE E a EEE E A aE aE a e A a a e aaa AAN aA 4 Building the Wall Frame oreraa a A AGR 5 Installing the Wall FraMiG nenene nani O S O 6 Introduction Determining the Mounting SUMaCG sisin n a e a E E 6 Wood St d lmstallatiOM senenin a aa aa a e aa a a a a Ea aAa 6 Concrete Installations ienssicccdeissassvsaeessdondasies caativevesancustbeiad cadavevs a e e a ae EN 8 Installing the Pullout Monkees an N TNA 10 Attach a P Series Mount and or ACCeSSOIiIeS siao aada a aa e Aa a aah 11 Post Installation AC UStM Nts reino R OES 11 Cable ROUTING cnoi i E O AONO 12 Technical Specifications cxcccscecccevssasvacnsacasce e aaa a e A AE a a a E a 12 Wan AINE sich hl ached arate cat a accra O T A E T E E 13 Weight Limit THE WALL STRUCTURE MUST BE CAPABLE OF RA
11. of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2011 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 13
12. r of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description

Download Pdf Manuals

image

Related Search

Related Contents

Husky HTC408BDLX12 HMT405BDLX16 Instructions / Assembly  ThinkPad A21e, A22e, i 1800 (MT 2655/2663/2664)  Macro Key Manager Benutzerhandbuch DE  

Copyright © All rights reserved.
Failed to retrieve file