AMX AVB-TX-CATPRO-HD15-5T
Contents
1. lt a Distance monitor with speakers Up to 1000 ft 305 m Connectors RX FG10 ko 10 48 01 a j RGBHV In 1 Female HD 15 RGBHV Local Out 1 Female HD 15 Local monitor Stereo Audio In 1 Female 3 5 mm mini stereo jack with speakers Stereo Audio Local Out 1 Female 3 5 mm mini stereo jack RGBHV Stereo Out 1 Female RJ 45 FIG 2 Typical system setup using CatPro Modules CatPro RGBHV Stereo Modules use power supplies provided with each unit To attach source device connectors and power to the TX Module AVB TX CATPRO HD15 ST FG1010 45 01 i e AUDIO VIDEO AUDIO VIDEO CAT 5 o0000 Q 90000 Q OCAL OUTPUT HD 15 OUTPUT RJ 45 FIG 3 Attach source device connectors RJ 45 connector and power to TX 1 Insert the audio mini jack 3 5 mm and the HD 15 connector into the Audio and the Video Input connectors 2 Insert the RJ 45 connector into the CAT 5 receptacle 3 Plug the desktop power supply into the power jack on the module and into an AC external power source If you are providing the power supply Plug the power cord from a UL or equivalent listed power supply into the power jack on the Module The electrical ratings must meet those indicated in the Specifications table 4 Optional To use the Local Out option insert the audio mini jack and the HD 15 connector into t2. 0 75 V to 0 3 V terminated Impedance 75 ohms Return Loss lt 35 dB 5 MHz RGB Local Out Signal Level Range 0 75 V to 0 3 V terminated Impedance 75 ohms Important A ways use a UL approved power source Check the power source s SNR gt 65 dB documentation for information specific to that power source Sync In System Setup er paras aie A typical setup using CatPro RGBHV Stereo TX and RX Modules is illustrated in y g FIG 2 The signals are sent to a monitor with speakers at a distance as well as to a Sync Local Out local monitor with speakers Signal Level Low 0 V High 5 V unterminated Polarity Active high or low follows input polarity Source PC Note When used with an AMX Radio In TX FG1010 45 01 AutoPatch Distribution Matrix aval Tve t overall cable length cannot exceed Signal Type Stereo unbalanced as a ap 1 000 ft 305 m Signal Levels max 8 dBu Ss Impedance 2 kohms o Audio Local Out Signal Type Stereo unbalanced Signal Levels max 8 dBu unity gain Frequency Response lt 0 35 dB 20 Hz to 20 kHz THD N lt 0 04 1 kHz 10 dBu to 4 dBu SNR gt 105 dB 20 Hz to 20 kHz Vin 4 dBu Impedance lt 5 ohms Connectors RGBHV Stereo In 1 Female RJ 45 RGBHV Out 1 Female HD 15 Stereo Audio Out 1 Pluggable 3 5 mm terminal block Module Installation Module Mounting Options Rack Trays and Mounting Brackets Search for V Style at www amx com
3. 80p 16 9 60 Hz 5 80 in 14 73 cm width up to 1000 ft 305 m 1 66 in 4 22 cm height RGB Out at 1000 ft Weight TX Module Approximately 1 5 Ib 0 68 kg Signal Level Range 0 75 V to 0 3 V typical terminated user adjustable with gain amp peak 75 ohms l d Dimensions RX Module 5 15 in 13 08 cm depth enue seo de 4 33 in 11 00 cm width 1 66 in 4 22 cm height Sync Out Weight RX Module Approximately 1 3 Ib 0 6 kg Signal Levels Low 0 V High 5 V unterminated Supported Twisted Pair Category cable 5 5e 6 6e and STP skew free cable is not Polarity Active high or low follows input polarity Cable Types recommended Audio Out at 1000 ft Note All measurements listed were taken using Cat5e cable Sani o Stereo unbalanced Approvals CE UL cUL RoHS Signal Levels max 8 dBu Volume Control Range Mute to 6 dB user adjustable The automatically adjusting universal 110 220 IEC power supply is ENERGY STAR qualified to Frequency Response lt 0 2 dB 20 Hz to 20 kHz ensure maximum efficiency and savings THD N lt 0 04 1 kHz 10 dBu to 4 dBu SNR gt 105 dB 20 Hz to 20 kHz Vin 4 dBu Impedance lt 5 ohms Skew Adjustment 0 to 62 ns in 2 ns increments on RGB channels user adjustable Specifications TX FG1010 45 01 Signal Types RGBHV Stereo Audio Maximum Resolution 1600x1200 4 3 and 1920x1080p 16 9 60 Hz up to 1000 ft 305 m RGB In Signal Level Range
4. Bang Quick Start Guide alt EFA AutoPatch CatPro RGBHV Stereo Modules Overview EDID Specifications TX FG1010 45 01 CatPro RGBHV Stereo Transmitter TX and Receiver RX Modules work together or work in conjunction with CatPro RGBHV Stereo boards on an AMX AutoPatch Distribution Matrix This guide contains complete information for standalone use For use with a distribution matrix see the distribution matrix s instruction manual on the AMX AutoPatch CD or at www amx com Standard Timing Identification 1600x1200 60 Hz This is the preferred timing identified in the EDID 1280x1024 85 Hz 1152x864 120 Hz 1280x800 60 Hz o o ol o N w N gt gt Front view 1280x720 60 Hz MIPRO TX 1024x768 120 Hz ID 5 800x600 120 Hz es Rear view 640x480 120 Hz Established Timing CatPro RGBHV Stereo TX Module CatPro RGBHV Stereo RX Module 720x400 70 Hz 88 Hz FG1010 45 01 FG1010 48 01 640x480 60 Hz 67 Hz 72 Hz 75 Hz 800x600 56 Hz 60 Hz 72 Hz 75 Hz 832x624 75 Hz 1024x768 60 Hz 70 Hz 75 Hz 87 Hz 1280x1024 75 Hz 1152x870 75 Hz FIG 1 CatPro RGBHV Stereo TX and RX Modules Specifications General Specifications TX FG1010 45 01 and RX FG1010 48 01 0 to 90 non condensing Specifications RX FG1010 48 01 Dimensions TX Module 5 15 in 13 08 cm depth Maximum Resolution 1600x1200 4 3 and 1920x10
5. and skew to obtain a sharp picture on the destination display Volume can also be adjusted during the procedure for adjusting skew Tip for Flat Panel LCDs For optimal results press the auto adjust button on the flat panel LCD after using the adjustment options on the RX Module Test Image File Black and white pattern Sample text Color bars FIG 6 Test Image file For full warranty information refer to www amx com 2 11 Test image files are provided on the AMX AutoPatch CD File names begin with the resolution 800x600 1024x768 1280x768 etc and end with SkewPattern e Turn the peak and gain potentiometers watch the black and white pattern and the text before and after skew adjustment for brightness and sharpness e Turn the Adjust knob for each color until the corresponding color bars align with the color bars directly below them Gain and Peak Gain and peak potentiometers on the RX can be used to compensate for overall cable length Important Do not push or over tighten the potentiometers when turning them To adjust the gain and peak 1 Optional On the PC open the test image file for the resolution of the source signal 2 If the picture s brightness needs to be increased or decreased turn the Gain potentiometer 3 If the picture is not sharp enough turn the Peak potentiometer Increasing the peak removes graininess 4 Repeat Steps 2 and 3 after adjusting the skew according to the
6. een Skew Adjust mode 5 Turn the Adjust knob clockwise or counter clockwise The green color component shifts right or left 6 Press the Adjust knob The LED turns blue and the module is placed in Blue Skew Adjust mode 7 Turn the Adjust knob clockwise or counter clockwise The blue color component shifts right or left 8 Press the Adjust knob The LED turns white and the module is placed in Volume Adjust mode 9 Turn the Adjust knob clockwise to increase volume or counter clockwise to decrease volume 10 Press the Adjust knob The LED turns off and the module saves all of the settings If the LED alternately blinks red and green see Troubleshooting below Tip To adjust the volume without changing the skew settings press the Adjust knob until the LED turns white and then complete Steps 9 and 10 above Troubleshooting LED Blinks Red and Green e If the LED alternately blinks red and green a configuration failure has occurred e Ifthe blinking happens when the Adjust knob is pressed to save see Step 10 in the skew adjustment procedure above the system failed to save the settings Any adjustments just made are still in effect but will be lost the next time power is cycled To save the adjustments repeat Steps 2 4 6 8 and 10 i e cycle the colors until the LED turns off If the blinking happens when power is cycled the system could not find valid settings and reverted to the factory defined default settings Com
7. he Local Output connectors To attach destination device connectors and power to the RX Module AVB RX CATPRO HD15 ST FG1010 48 01 1 1 1 1 r Audio wiring FIG 4 Attach destination device connectors and power to RX 1 Insert the HD 15 connector and wire the audio connector wiring shown is for an unbalanced output signal 2 Insert the RJ 45 connector into the CAT 5 receptacle 3 Plug the power cord into the power jack and into the power source If you are providing the power supply Plug the power cord from a UL or equivalent listed power supply into the power jack on the Module The electrical ratings must meet those indicated in the Specifications table 4 If the destination display needs adjusting see Adjusting the Picture below TX and RX HD 15 Pinouts Input VESA DDC Compliant 1 Red 6 Red GND 11 ID Bit 2 Green 7 Green GND 12 DDC SDA 3 Blue 8 Blue GND 13 Horizontal Sync 4 ID Bit 9 5VinDDC 14 Vertical Sync 5 GND 10 GND 15 DDC SCL Output Red 6 Red GND 11 ID Bit Green 7 Green GND 12 ID Bit Blue 8 Blue GND 13 Horizontal Sync ID Bit 9 5 Vout DDC 14 Vertical Sync GND 10 GND 15 ID Bit FIG 5 Connector pinouts for HD 15 TX In and for TX and RX Out ARON Note 55 mA supplied on output pin 9 power draw not to exceed 50 mA per port Adjusting the Picture This section includes information for adjusting the gain peak
8. plete Steps 2 through 10 again 2011 AMX All rights reserved AMX and the AMX logo are registered trademarks of AMX AMX reserves the right to alter specifications without notice at any time 3000 RESEARCH DRIVE RICHARDSON TX 75082 e 800 222 0193 e fax 469 624 7153 technical support 800 932 6993 www amx com 93 10 828 01 REV B fJ baar Lro
9. steps below Skew and Volume The adjust knob on the RX Module can be used to compensate for skew inherent in UTP cable by adjusting the skew of the video signals The knob also adjusts the volume A small screwdriver works well for turning and pressing the knob The knob does not have a mechanical start or stop point If the LED blinks when the knob is turned the setting has reached its minimum or maximum point The RX Module ships with factory defined default settings of no skew delay for the skew on R G and B and to unity gain on the volume Once the adjustment process has been successfully completed and saved the new settings replace the factory defined settings The system will restore the new settings whenever power is cycled To abort the adjustment procedure at any time hold the Adjust knob down until the LED blinks 3 times and the RX Module reverts to its previous settings Cycling power on the module during the adjustment procedure will have the same effect The individual settings are not stored in memory until all adjustments Steps 2 10 below have been made To adjust the skew and volume 1 Optional Open the test image file on the PC 2 Press the Adjust knob The LED turns red and the module is placed in Red Skew Adjust mode 3 Turn the Adjust knob clockwise or counter clockwise The red color component shifts right or left 4 Press the Adjust knob The LED turns green and the module is placed in Gr
Download Pdf Manuals
Related Search