Home

Mitsubishi Electric EW331U-ST data projector

Contents

1. When using an external hub or router use a Category 5 straight cable A crossed cable can be used with some hubs and routers See the appropriate documentation for more information Don t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged from your body causing damage to the projector Configuring the LAN Control Settings If you are in a DHCP environment 1 2 3 SS Oy e co Make sure the projector and your computer are properly connected to the same local area network Press MENU EXIT and then press lt P gt until the SYSTEM SETUP Advanced menu is highlighted Press W to highlight LAN Control Settings and press MODE ENTER The LAN Control Settings page is displayed Press W to highlight Control By and press lt P gt to select LAN Press W to highlight DHCP and press lt gt to select On Press W to highlight Apply and press MODE ENTER Please wait for around 15 20 seconds and then re enter the LAN Control Settings page The IP Address Subnet Mask Default Gateway and DNS Server settings will be displayed Note down the IP address displayed in the IP Address row If the IP Address still does not appear contact your network administrator If the LAN cables are not properly connected the IP Address Subnet Mask Default Gateway and DNS Server settings will display 0 0 0 0 Make sure the LAN cables are properly connected and perform the above procedures again
2. If you are in a non DHCP environment l 2 3 SN T Repeat steps 1 4 above Press W to highlight DHCP and press lt gt to select Off Contact your network administrator for information on the IP Address Subnet Mask Default Gateway and DNS Server settings Press W to select the item you want to modify and press MODE ENTER Press lt p gt to move the cursor and then press A W to enter the value To save the setting press MODE ENTER If you do not want to save the setting press MENU EXIT Press W to highlight Apply and press MODE ENTER Cz If the LAN cables are not properly connected the IP Address Subnet Mask Default Gateway and DNS Server settings will display 0 0 0 0 Make sure the LAN cables are properly connected and perform the above procedures again EN 36 Controlling the projector remotely through a web browser e Control Once you have the correct IP address for the projector and the projector is on or in standby state you can use any computer that is on the same local area network to control the projector ENGLISH m When using this function Adobe Flash Player has to be installed in your computer Please download Adobe Flash Player from the website of Adobe Systems Incorporated 1 Enter the IP address of the projector in the address bar of your browser and press enter for example http 192 168 0 146 4 ter p i ola A 0 E 1 Live Search X w A C7 When using
3. ENGLISH Cz If the timer is already on the timer will restart whenever the Timer period is reset 3 Press W to highlight Timer display and choose if you want the timer to show up on the screen by pressing lt gt Selection Description Always Displays the timer on screen throughout the presentation time 1 min 2 min 3 min Displays the timer on screen in the last 1 2 3 minute s Never Hides the timer throughout the presentation time 4 Press Y to highlight Timer position and set the timer position by pressing lt gt ae 5 Press W to highlight Timer counting direction and select your desired counting direction by pressing lt q P gt Selection Description Count Up Count Down Increases from 0 to the preset time Decrease from the preset time to 0 6 Press W to highlight Sound reminder and decide if you want to activate sound reminder by pressing lt b gt If you select On a double beep sound will be heard at the last 30 seconds of counting down up and a triple beep sound will be produced when the timer is up 7 To activate the presentation timer press W and press lt P gt to select On and press MODE ENTER 8 A confirmation message is displayed Highlight Yes and press MODE ENTER to confirm You will see the message Timer is On appearing on the screen The timer starts counting once the timer is turned on C7 If you switch input signal or press AUTO
4. The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type To select a operation mode that suits your need you can follow one of the following steps POWER TEMP LAMP Press MODE ENTER on the remote control or projector repeatedly until your desired mode is selected Go to the PICTURE gt Setting menu and press lt gt to select a desired mode Picture modes for different types of signals The picture modes available for different types of signals are listed below 1 Brightest mode Maximizes the brightness of the projected image This mode is suitable for environments where extra high brightness is required such as using the projector in well lit rooms Presentation mode Is designed for presentations The brightness is emphasized in this mode to match PC and notebook coloring For Video input signals this mode is suitable for playing gamebox based video games in a normal living room lighting level environment Normal mode Maximizes the purity of RGB colors to provide true to life images regardless of brightness setting It is most suitable for viewing photos and for viewing PC graphic and drawing applications such as AutoCAD For Video input signals this mode is appropriate for viewing colorful movies video clips from digital cameras or DVs Theater mode Is appropriate for playing colorful movies video clips fr
5. MITSUBISHI ELECTRIC DLP PROJECTOR MODEL EX321U ST EW331U ST User Manual F JLink This User Manual is important to you Please read it before using your projector LISH CAUTION RISK OF ELECTRIC SHOCK CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACk NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsu lated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING CAUTION NOTE SHALL BE EASILY ACCESSIBLE TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUT LET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT THE SOCKET OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND WARNING Use the attached specified power supply cord If you use another power supply cord it may cause interference with radio and television recepti
6. 8 LAMP indicator light Indicates the status of the lamp Lights up or flashes when the lamp has developed a problem See Indicators on page 53 for details 9 AUTO Automatically determines the best picture timings for the displayed image See Auto adjusting the image on page 25 for details 10 Keystone Arrow keys w A Up a W Down Manually corrects distorted images resulting from an angled projection See Correcting keystone on page 25 for details 11 p gt Right Activates panel key lock See Locking control keys on page 32 for details When the On Screen Display OSD menu is activated the 4 10 and 11 keys are used as directional arrows to select the desired menu items and to make adjustments See Using the menus on page 22 for details 12 POWER ON STANDBY Toggles the projector between standby mode and on See Starting up the projector on page 21 and Shutting down the projector on page 33 for details MENU EXIT EN 8 Remote control C POWER ON STANDBY Toggles the projector between standby mode and on See Starting up the projector on page 21 and Shutting down the projector on page 33 for details FREEZE Freezes the projected image See Freezing the image on page 32 for details lt Left Selects the desired menu items and makes adjustments See Using the menus on page 22 for details BLANK Used to hide the screen picture See Hiding the image o
7. EN 46 Maintenance Care of the projector Your projector needs little maintenance The only thing you need to do on a regular basis is to keep the lens clean ENGLISH m Never remove any parts of the projector except the lamp Contact your dealer if other parts need replacing Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface e Usea canister of compressed air to remove dust e If there is dirt or smears use lens cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface A Never rub the lens with abrasive materials Cleaning the projector case Before you clean the case turn the projector off using the proper shutdown procedure as described in Shutting down the projector on page 33 and unplug the power cord To remove dirt or dust wipe the case with a soft lint free cloth e To remove stubborn dirt or stains moisten a soft cloth with water and a neutral pH detergent Then wipe the case A Never use wax alcohol benzene thinner or other chemical detergents These can damage the case Flammable substances may ignite causing fire or breakdown while the lamp is illuminating Storing the projector If you need to store the projector for an extended time please follow the instructions below e Make sure the temperature and humidity of the storage area are within the recommended range for the projector Please refer to Specifications on page 55 or cons
8. Inquiries Phone 4 34 93 586 27 51 Fax 24 34 93 588 53 87 E mail mitsubishi profesional sp mee com MEU SWE Mitsubishi Electric Europe B V Scandinavian Branch Hammarbacken 14 Box 750 S 19127 Sollentuna Sweden Sales Inquiries Phone _ 46 0 8 6251070 Fax 4 46 0 8 6251036 Technical Inquiries Phone _ 46 0 8 6251052 Fax 46 0 8 6251036 MEU UK Mitsubishi Electric Europe http vis mitsubishielectric co uk products projectors Visual Information Systems Division Travellers Lane Hatfield Hertfordshire AL10 8XB U K Sales Inquiries Phone 44 1707 278684 Fax 44 1707 278541 E mail projector info meuk mee com Technical Inquiries Phone 44 870 606 5008 Fax 44 1506 431927 E mail projector info meuk mee com Asia CHINA Mitsubishi Electric Air Conditioning amp Visual Information Systems Shanghai Ltd 15 F Henderson Metropolitan No 300 East Nanjing Road Shanghai 200001 China Sales amp Technical Inquiries Phone 86 21 2312 3030 Ext 3228 Fax 86 21 2312 3008 E mail _ vis support mlc mehkg com Sale and Service hotline Phone 86 400 820 2130 HONG KONG Mitsubishi Electric Ryoden Air Conditioning amp Visual Information Systems HongKong Ltd 7th Floor Manulife Tower 169 Electric Road North Point Hong Kong Sales Inquiries Phone 4 852 2510 1505 Fax 852 2510 0463 Technical Inquiries Phone 14 852 2422 0161 Fax 852 2487 0181 SINGAPORE Mitsubishi Elec
9. an Opera browser add index html after the IP address for example http 192 168 0 146 index html 2 The remote network operation page is displayed This page allows you to operate the projector as if you were using the remote control or control panel on the projector Press lt p gt to reveal more buttons i These buttons function the same as the ones on the OSD menus or remote control See 2 PICTURE menu on page 44 and Remote control on page 9 for details ii To switch input source click on your desired source CF When you use the projector control panel or remote control to change the OSD menu settings it may take a while for the web browser to synchronize these changes with the projector 3 The Tools page allows you to manage the projector configure the LAN control settings and secure access of remote network operation on this projector er i When using the Crestron Control System please refer to the user manual of Crestron Control system for setup information ii You can name the projector keep track of its location and the person in charge of it This column allows a maximum of 32 single byte characters iii You can adjust the LAN Control Settings EN 37 iv Once set access to the remote network operation page on this projector has been password protected To enable this function check the box in front of Enable and type in your desired password in the New Password colum
10. is not correctly connected to the input signal device The input signal has not been correctly selected Turn the video source on and check that the signal cable is connected correctly Check the connection Select the correct input signal with the SOURCE key on the projector or remote control The lens cover is still closed Open the lens cover Blurred image Cause Remedy The projection lens is not correctly focused Adjust the focus of the lens using the focus ring The projector and the screen are not aligned properly Adjust the projection angle and direction as well as the height of the unit if necessary The lens cover is still closed Open the lens cover Remote control does not work Cause Remedy The battery is out of power Replace the battery with a new one There is an obstacle between the remote control and the projector Remove the obstacle You are too far away from the projector Stand within 8 meters 26 feet of the projector The password is incorrect You do not remember the password Please see Entering the password recall procedure on page 23 for details The LAN function cannot be used EN 54 Cause Remedy LAN control settings or LAN cable connection are problematic Verify the LAN control settings Please see Configuring the LAN Control Settings on page 36 for details Make sure the LAN ca
11. lamp You may get injured by glass fragments Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling Don t remove the lamp for any purpose other than replacement Unnecessary removal of the lamp may result in a breakdown This projector uses a high pressure mercury lamp as the light source The high pressure mercury lamp may explode or fail to illuminate permanently because of an impact scratch or deterioration through use The period of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp depending on operation conditions Therefore the lamp may explode soon after the start of use The possibility of explosion of the lamp increases if you use it beyond its replacement period When the instruction of lamp replacement appears replace it with a new one immediately even if the lamp is still lighting normally When the high pressure mercury lamp explodes glass fragments will scatter inside or outside the lamp box and the gas charged inside the lamp will diffuse inside or outside the projector The gas inside the lamp contains mercury Be careful not to breathe it or avoid it from entering your eye or mouth If you should breathe it or if it should enter your eye or mouth see a doctor immediately This lamp contains mercury Consult your local hazardous waste regulations to dispose of this lamp in a proper manner Be sure to use the lamp dedicated to this projector V
12. of three pin grounding type Do not remove the grounding pin from the power plug If the power plug doesn t fit your wall outlet ask an electrician to change the wall out let In case that the power cord for the U S is provided with this projec tor never connect this cord to any outlet or power supply using other voltages or frequencies than rated If you want to use a power sup ply using other voltage than rated prepare an appropriate power cord separately Use 100 240 V AC 50 60 Hz to prevent fire or electric shock Do not place any objects on the power cord or do not place the pro jector near heat sources to prevent damage to the power cord If the power cord should be damaged contact your dealer for replace ment because it may cause fire or electric shock Do not modify or alter the power cord If the power cord is modified or altered it may cause fire or electric shock EN 3 ENGLISH m Contents Important safeguards Projector exterior view Controls and functions POSit ONIN SY OF Projectors ssena RE E sane vacepnes aiaa r ous E EE SREI 11 Connection Operation Adjusting the projected tia ge isieszcssevisecsnccgstius soca cenessevechsunssvschdeveatesvasiestutescposaseoespanenedvesbdenedsuni E 25 Optimizing the image Supervising and controlling by Computer sisisi eiee sariei iet E E AEE EEEE S EESE 36 Meny operation reenson seeen e EEr nET ROPE EEEE A EEE EEEE EEE EE EE EARE NEE E ETEA SG 41 Maintenan
13. on page 23 for details If you enter an incorrect password 5 times in succession the projector will automatically shut down in a short time Entering the password recall procedure 1 Press and hold AUTO on the projector or remote control for 3 seconds when the message INPUT PASSWORD is displayed The projector will display a coded number on the screen Write down the number and turn off your projector Please obtain a password using the Mitsubishi Password Decoder Software Operation Manual included in this CD Changing the password 1 4 Open the OSD menu and go to the SYSTEM SETUP Advanced gt Security Settings gt Change password menu Press MODE ENTER The message INPUT CURRENT PASSWORD is displayed Enter the old password If the password is correct another message INPUT NEW PASSWORD is displayed If the password is incorrect the password error message is displayed lasting for three seconds and the message INPUT CURRENT PASSWORD is displayed for your retry You can press MENU EXIT to cancel the change or try another password Enter a new password CF The digits being input will be displayed as asterisks on screen Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it EN 23 ENGLISH assword eep this number in a safe place onfirm the new password by re entering the new pas
14. or router to communicate across networks subnets that are divided by Subnet Mask MAC Address Abbreviation for Media Access Control Address MAC Address is a unique ID number assigned to each network adapter And this is based on which data are sent and received between network adapt ers Menu operation Menu system Please note that the on screen display OSD menus vary according to the signal type selected ENGLISH m Main menu Sub menu Options Wall Screen a Green Blue Aspect Ratio Auto Real Full EW331U ST only 4 3 16 9 Keystone Position 1 DISPLAY Phase H Size Magnify 3D On Off 3D Sync 1 2 Setting Brightest Presentation Normal Theater User 1 User 2 Brightness Contrast Color Tint Sharpness 2 PICTURE BrilliantColor On Off Color Temperature T1 T2 T3 T4 Primary Color R G B C M Y 3D Color Management Saturation Gain Save Settings 3 SOURCE Quick Auto Search On Off Color Space Conversion RGB YUV Auto Timer period 1 240 minutes Timer display Always 1 min 2 min 3 min Never Timer position a ee Presentation Timer g 4 oa Count Down Count Up SYSTEM SETUP Sound reminder On Off Basic On Off Language English Frangais Deutsch Italiano Espafol Pycckun SAGE AYC fai P A REE StS O1 Svenska Tiirkge CeStina Portugu s ns Polski Magyar y at EN 41 Projector Position Front Table Rear Table Rea
15. proportionately When determining the position of the screen and projector you will need to account for both the projected image size and the vertical offset dimension which are directly proportional to the projection distance When fine streaks are seen on projected images This is due to interference with the screen surface and is not a mal function Replace the screen or displace the focus a little How to determine the position of the projector for a given screen size 1 Determine the aspect ratio of your screen 16 9 or 4 3 If you have a 4 3 screen refer to the table labeled Standard If you have a 16 9 screen refer to the table labeled 16 9 2 Select your screen size 3 Refer to the table and find the closest match to your screen size in the left columns labeled Screen Using this value look across this row to the right to find the corresponding average distance from screen value in the column labeled Distance from the screen L This is the projection distance 4 On that same row look across to the right column and make note of the Hd value This will determine the final vertical offset placement of the projector in relation to the edge of the screen 5 The recommended position for the projector is aligned perpendicular to the horizontal center of the screen at the distance from the screen determined in step 3 above and offset by the value determined in step 4 above EX321U ST For example if you are usi
16. qualified service personnel Damage requiring service Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions a If the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the pro jector c If the projector does not operate normally after you follow the operating instructions Adjust only those controls that are covered by the operating instructions An improper adjust ment of other controls may result in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation d If the projector has been exposed to rain or water e If the projector has been dropped or the cabinet has been damaged f Ifthe projector exhibits a distinct change in performance this indicates a need for service Replacement parts When replacement parts are required be sure that the service technician has used replacement parts specified by the manufac turer or parts having the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety check Upon completion of any service or repair to this projector ask the service technician to perform safety checks determining that the projector is in a safe operating condition ENGLISH EN 5 WARNING Unplug immediately if there is something wrong with yo
17. release the function press any key on the projector or remote control Even if an image is frozen on the screen the pictures are running on the video or other device If the connected devices have active audio output you will still hear the audio even though the image is frozen on screen afterimages may linger on the screen Adjusting the sound EN 32 The sound adjustments made as below will have an effect on the projector speaker Be sure you have made a correct connection to the projector audio input See Connection on page 16 for how the audio input is connected Muting the sound To temporarily turn off the sound 1 Press MENU EXIT and then press lt P gt until the SYSTEM SETUP Advanced menu is highlighted 2 Press W to highlight Audio Settings and press MODE ENTER The g Audio Settings page is displayed a _ VOLUME MAGNIFY 3 Highlight Mute and press lt P gt to select On oc Adjusting the sound level To adjust the sound level press VOLUME on the remote control or 1 Repeat steps 1 2 above 2 Press W to highlight Volume and press lt gt to select a desired sound level Standby Audio Out Selecting On enables the function The projector can output an Audio input signal when it is in standby mode and Audio input and Audio out jack is correctly connected to devices ENGLISH m CF7 When the projector enters standby mode the audio will be interrupted briefly This is not a pr
18. same row look across to the right column and make note of the Hd value This will determine the final placement of the screen in relation to the horizontal plane of the projector EX321U ST For example if your measured projection distance was 1 5 m and your screen aspect ratio is 4 3 the closest match in the Distance from the screen L column is 1 5 m Looking across this row shows that a 120 inch screen is required EW331U ST For example if your measured projection distance was 1 5 m and your screen aspect ratio is 16 10 the closest match in the Distance from the screen L column is from 1 6 m Looking across this row shows that a 150 inch screen is required EN 13 ENGLISH m Layout of the projector Image size varies depending on the distance between the screen and the projector Front projection Hd L Between the screen and the front edge of the projector H Height of the projected image Standard EX321U ST Screen Diagonal Size Width W Height H BANGO Homie Saraan rd inch cm inch cm inch cm inch m inch cm 40 102 32 81 24 61 19 0 5 4 9 60 152 48 122 36 91 29 0 7 5 14 80 203 64 163 48 122 39 1 0 7 18 100 254 80 203 60 152 49 12 9 23 120 305 96 244 72 183 58 1 5 11 27 150 381 120 305 90 229 73 1 9 14 34 200 508 160 406 120 305 97 25 18 46 250 635 200 508
19. scaled to a 16 10 aspect display area Thus a 16 9 aspect image will not utilize 10 of the height of a 16 10 aspect image displayed by this projector This will be seen as darkened unlit bars along the top and bottom vertical 5 height respectively of the 16 10 projection display area whenever displaying a scaled 16 9 aspect image in the vertical center of the 16 10 projection display area The projector should always be placed horizontally level like flat on a table and positioned directly perpendicular 90 right angle square to the horizontal center of the screen This prevents image distortion caused by angled projections or projecting onto angled surfaces The modern digital projector does not project directly forward like older style reel to reel film projectors did Instead digital projectors are designed to project at a slightly upward angle above the horizontal plane of the projector This is so that they can be readily placed on a table and will project forward and upwards onto a screen positioned so that the bottom edge of the screen is above the level of the table and everyone in the room can see the screen You can see from the diagram on page 14 that this type of projection causes the bottom edge of the projected image to be vertically offset from the horizontal plane of the projector If the projector is positioned further away from the screen the projected image size increases and the vertical offset also increases
20. to display the Zoom bar Press MAGNIFY to magnify the center of the picture Press the key repeatedly until the picture size is suitable for your need Use the directional arrows A W lt gt on the projector or remote control to navigate the picture To restore the picture to its original size press AUTO You can also press MAGNIFY When the key is pressed again the picture is further reduced until it is restored to the original size Using the OSD menu Press MENU EXIT and then press lt P gt until the DISPLAY menu is highlighted Press W to highlight Magnify and press MODE ENTER The Zoom bar is displayed Repeat steps 2 4 in the section of Using the remote control above Or if you are using the projector control panel continue to the following steps Press A on the projector repeatedly to magnify the picture to a desired size To navigate the picture press MODE ENTER to switch to the panning mode and press the directional arrows A V lt P gt to navigate the picture Use the directional arrows A V lt 4 gt on the projector or remote control to navigate the picture To reduce size of the picture press MODE ENTER to switch back to the zoom in out functionality and press AUTO to restore the picture to its original size You can also press W repeatedly until it is restored to the original size gt The picture can only be navigated after the picture is magnified You can further magnify the pictur
21. when the timer is on the timer will be stopped To cancel the timer perform the following steps 1 Go back to the Presentation Timer page 2 Press W and press lt p gt to highlight Off and press MODE ENTER A confirmation message is displayed 3 Highlight Yes and press MODE ENTER to confirm You will see the message Timer is Off appearing on the screen How to use the TIMER On key TIMER ON is a multi functional key e If the presentation timer is off pressing this key displays a confirmation message You can decide whether to activate the timer or not by following the on screen instruction e Ifthe timer is already on pressing this key displays a confirmation message You can decide whether to restart continue or turn off the timer by following the on screen instruction EN 31 Hiding the image Cz Once BLANK is pressed the projector enters Low mode automatically In order to draw the audience s full attention to the presenter you can use BLANK on the projector or remote control to hide the screen image Press any key on the projector or remote control to restore the image The word BLANK appears at the lower right corner of the screen while the image is hidden You can set the blank time in the SYSTEM SETUP Basic gt Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen Do not block the projection lens from pro
22. 02 85 938 148 500 1440 x 900 WXGA _60 59 887 55 935 106 500 1400 x 1050 SXGA _60 59 978 65 317 121 750 1600 x 1200 UXGA 60 000 75 000 162 000 640 x 480 67Hz MAC13 66 667 35 000 30 240 832 x 624 75Hz MAC16 74 546 49 722 57 280 1024 x 768 75Hz MAC19 75 020 60 241 80 000 1152 x 870 75Hz MAC21 75 06 68 68 100 00 C The projector only supports the timing 720 x 400 with 5 lines R G B H V EN 56 EX321U ST dose not support the timing of WXGA_120 upporte ti ing or P input 9 99 9 1 9 1 i 1 9 1 119 1 191 1 9 1 9 1 1 119 1 1199 9 1 9 99 9 1 119 9 9 1 91 9 5 1 1199 9 de 1 1 1 91 1 99 1 9 1 9 1 1 9 9 9 9 9 1 1 99 1 1a 1 E 1 1 1 1 1 1 S dose not support the timing of GA 1 G7 E EN ENGLISH m upporte ti ing or o ponent P Prinput 99 99 C3 isplayinga 1 idi i H or1 ili i H signal may result in slight image vibration upporte ti ing or ieo n i eo inputs N 1 1 E 1 1 N 1 I N I What s included in the bo AC power cord for S G 1111 1 1 emote control with battery forE Indonesia G 1 71 1 Safety manual uick start up for G 11 1 1C for A G1 11 1 Soft carrying case for South orea G 1 71 for A G Fo A 1 G cable 1 eplacement part ption Not included in t
23. 049 2102 486 1330 Fax 0049 2102 486 1340 MEU IR Mitsubishi Electric Europe B V Irish Branch http www mitsubishi ie Westgate Business Park Ballymount Dublin 24 Ireland Sales Inquiries Phone 353 1 4198807 Fax 353 1 4198890 Technical Inquiries Phone 353 1 4198808 Fax 353 1 4198895 MEU IT Mitsubishi Electric Europe B V Italian Branch Centro Direzionale Colleoni Palazzo Sirio Viale Colleoni 7 20041 Agrate Brianza Italy Sales amp Technical Inquiries Phone 39 0 39 60531 Fax 39 0 39 6053214 E mail info projector it mee com MEU NL Mitsubishi Electric Europe B V Benelux Branch http www mitsubishielectric nl Nijverheidsweg 23A 3641 RP Mijdrecht The Netherlands Sales Inquiries Phone 31 297 282461 Fax 31 297 283936 E mail info mitsubishi nl Technical Inquiries Phone 31 297 282461 Fax 31 297 283936 E mail info mitsubishi nl Russia Mitsubishi Electric Europe B V Moscow Representative Office http www mitsubishi projector ru Moscow Representative Office 52 5 Kosmodamianskaya Nab 115054 Moscow Russia Sales amp Technical Inquiries Phone 7095 721 2068 Fax 7095 721 2071 MEU SP Mitsubishi Electric Europe B V Spanish Branch http www mitsubishielectric es Ctra de Rubi 76 80 08173 Sant Cugat del Valles Barcelona Spain Sales Inquiries Phone 4 34 93 565 31 54 Fax 1 34 93 589 43 88 E mail mitsubishi profesional sp mee com Technical
24. 123 311 109 2 8 13 34 270 686 235 598 132 336 118 3 0 15 37 300 762 261 664 147 374 131 3 3 16 41 CF The above figures are approximate and may be slightly different from the actual measurements Mitsubishi recommends that if you intend to permanently install the projector you should physically test the projection size and distance using the actual projector in suit before you permanently install it so as to make allowance for this projector s optical characteristics This will help you determine the exact mounting position so that it best suits your installation location EN 15 ENGLISH m Connection When connecting a signal source to the projector be sure to 1 Turn all equipment off before making any connections 2 Use the correct signal cables for each source 3 Ensure the cables are firmly inserted Cc See the owner s guide of each device for details about its connections Contact your dealer for details about its connections In the connections shown below some cables may not be included with the projector They are commercially available from electronics stores Connecting a computer or monitor Connecting a computer The projector provides a RGB input socket that allows you to connect it to both IBM compatibles and Macintosh computers A Mac adapter is needed if you are connecting legacy version Macintosh computers To connect the projector to a notebook or desktop compute
25. 150 381 122 3l 23 57 300 762 240 610 180 457 146 3 7 27 69 EW331U ST Screen Diagonal Size Width W Height H i at Dec hel ji inch cm inch cm inch cm inch m inch cm 50 127 42 108 26 67 21 0 5 1 3 60 152 51 129 32 81 25 0 6 2 4 80 203 68 172 42 108 33 0 8 2 5 100 254 85 215 53 135 41 La 3 7 120 305 102 258 64 162 50 13 3 8 150 381 127 323 79 202 62 1 6 4 10 200 508 170 431 106 269 83 2 1 3 13 250 635 212 538 132 337 104 2 6 7 I7 270 686 229 582 143 363 112 2 8 7 18 300 762 254 646 159 404 124 3 2 8 20 EN 14 16 9 EX321U ST Screen Diagonal Size Width W Height H Distance noun ns Serene t a inch cm inch cm inch cm inch m inch cm 40 102 35 89 20 50 21 0 5 7 18 60 152 52 133 29 75 31 0 8 11 27 80 203 70 177 39 100 42 1 1 14 36 100 254 87 221 49 125 52 1 3 18 45 120 305 105 266 59 149 63 1 6 21 55 150 381 131 332 74 187 78 2 0 27 68 200 508 174 443 98 249 105 2 7 36 91 250 635 218 553 123 311 131 3 3 45 114 300 762 261 664 147 374 157 4 0 54 136 EW331U ST Screen Distance from the screen L Hd Diagonal Size Width W Height H inch cm inch cm inch cm inch m inch cm 50 127 44 111 25 62 22 0 6 3 60 152 52 133 29 75 26 0 7 3 80 203 70 174 39 100 35 0 9 4 11 100 254 87 221 49 125 44 1 1 5 14 120 305 105 266 59 149 52 1 3 6 16 150 381 131 332 74 187 65 1 7 8 21 200 508 174 443 98 249 87 2 2 11 27 250 635 218 553
26. 7 59 94 VGA120 640 x 480 61 91 119 52 SVGA60 800 x 600 37 88 60 32 SVGA120 800 x 600 76 30 119 97 SVGA120 800 x 600 77 43 119 85 XGA60 1024 x 768 48 36 60 00 XGA120 1024 x 768 97 55 119 99 WXGA60 1280 x 800 49 70 59 81 h oe UST 1280 x 800 101 56 119 91 If DVD is run by 480p signals 3D image may not be displayed correctly depending on the DVD player If 3D image is projected on the screen in 120Hz the image may not appear on the screen depending on software of DVD player Notes on danger to public health during watching 3D image Stop watching 3D image if you feel fatigue or discomfort Stop watching 3D image if you see doubly blurred image or you cannot view the image stereoscopically The following people need to refrain from use as with 3D image a photosensitive patient a patient with heart disease a person in poor physical condition a sleepy person a very tired person a drunk person children EN 35 ENGLISH Supervising and controlling by computer With a proper LAN cable connection and LAN Control settings you can operate the projector from a computer using a web browser or PJLink application when the computer and the projector are connected to the same local area network gt This projector supports Crestron software and PJLink An example of connecting the projector to computer External hub Computer LAN cable option 100BASE TX or 1OBASE T should be supported
27. 75 9503 STC Setsuyo Astec Corporation Seoul Branch 16F KT Bldg 28 2 Yeouido dong Yeoungdeungpo gu Seoul 150 931 Korea Sales amp Technical Inquiries Phone 82 1588 5576 Fax 82 2 704 8666 MALAYSIA Melco Sales Malaysia Sdn Bhd Lot 11 Jalan 219 46100 Petaling Jaya Selangor Darul Ehsan Malaysia Sales amp Technical Inquiries Phone 60 0 3 79573428 Fax 60 0 3 79563950 60 0 3 79582576 Technical amp Service Inquiries Phone 60 0 3 79553997 Fax 60 0 3 79584836 ME TWN Mitsubishi Electric Taiwan Co Ltd http www MitsubishiElectric com tw 11TH FL 90 SEC 6 CHUNG SHAN N RD TAIPEI 111 R O C Sales amp Technical Inquiries Phone 886 2 2832 8255 Fax 886 2 2833 9813 MKY Mitsubishi Electric Kang Yong Watana Co Ltd http www mitsubishi kyw co th Road Huamark Bangkapi Bangkok 10240 Thailand Sales amp Technical Inquiries Phone 66 2 731 6841 Fax 66 2 379 4763 Oceania ME AUST Mitsubishi Electric Australia http www mitsubishielectric com au 163 htm 348 Victoria Road Rydalmere N S W 2116 Australia Sales amp Technical Inquiries Phone 612 9684 7777 Fax 612 9684 7208 E mail diamonddigital meaust meap com Technical Inquiries Phone 612 9684 7694 Fax 612 9684 7684 E mail service meaust meap com BDT Black Diamond Technologies Ltd Warranty Registration http www bdt co nz projectors warranty asp 1 Parliament St Lower Hutt Wellington
28. EN 11 ENGLISH Obtaining a preferred projected image size EN 12 The distance from the projector lens to the screen the zoom setting if available and the video format each factors in the projected image size 4 3 is the native aspect ratio of EX321U ST To be able to project a complete 16 9 widescreen aspect ratio image the projector can resize and scale a widescreen image to the projector s native aspect width This will result in a proportionally smaller height equivalent to 75 of the projector s native aspect height O O Oe SOs 4 3 aspect image in a 4 3 aspect display area 16 9 aspect image scaled to a 4 3 aspect display area Thus a 16 9 aspect image will not utilize 25 of the height of a 4 3 aspect image displayed by this projector This will be seen as darkened unlit bars along the top and bottom vertical 12 5 height respectively of the 4 3 projection display area whenever displaying a scaled 16 9 aspect image in the vertical center of the 4 3 projection display area 16 10 is the native aspect ratio of EW331U ST To be able to project a complete 16 9 widescreen aspect ratio image the projector can resize and scale a widescreen image to the projector s native aspect width This will result in a proportionally smaller height equivalent to 90 of the projector s native aspect height 4 3 aspect image in a 16 10 aspect display area 16 9 aspect image
29. ENGLISH Adjusting Brightness Highlight Brightness in the PICTURE menu and adjust the values by pressing lt P on the projector or remote control The higher the value the brighter the image And lower the setting darker the image Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible Adjusting Contrast Highlight Contrast in the PICTURE menu and adjust the values by pressing lt p gt on the projector or remote control The higher the value the greater the contrast Use this to set the peak white J L my level after you have previously adjusted the Brightness setting to suit your an A a selected input and viewing environment af ap 30 be E 0 E 30 Adjusting Color Highlight Color in the PICTURE menu and adjust the values by pressing lt P on the projector or remote control Lower setting produces less saturated colors If the setting is too high colors on the image will be overpowering which makes the image unrealistic Adjusting Tint Highlight Tint in the PICTURE menu and adjust the values by pressing lt 4 gt on the projector or remote control The higher the value the more reddish the picture becomes The lower the value the more greenish the picture becomes Adjusting Sharpness Highlight Sharpness in the PICTURE menu and adjust the values by pressing lt 4 gt on the projector or remote control The higher the valu
30. K and audio mute disable 31 BLANK and audio mute enable ERST Inquiry about the error state 1st byte Fan error 0 or 2 2nd byte Lamp error 0 or 2 3rd byte Temperature error 0 or 2 4th byte Always 0 5th byte Always 0 6th byte Always 0 0 or 2 mean as follows 0 No error detected 2 Error LAMP Inquiry about the lamp state 1st value 1 to 4 digits Cumulative lamp operating time This item shows a lamp operating time hour calculated based on that Lamp Mode is Low 2nd value 0 Lamp off 1 Lamp on INST Inquiry about the available inputs The following value is returned 11 12 21 2231 NAME Inquiry about the projector name The command responds with the projector name specified in the Tools page INF1 Inquiry about the manufacturer MITSUBISHI is returned name EN 39 ENGLISH m INF2 Inquiry about the model name EX321U ST or EW331U ST is returned INFO Inquiry about other information No other information is available No parameter is returned CLSS Inquiry about the class information 1 is returned Er EN 40 The PJLink INPT will be replied only when the source is displayed on screen When there is no signal only Unavailable Time will be answered The above mentioned control may not be performed correctly or the monitoring data may not be obtained correctly in the following conditions During standby Du
31. LT EX320LP for EX321U ST EW331U ST Use of other lamps may cause a failure of the projector Turn the power off and disconnect the projector from the wall socket If the lamp is hot avoid burns by waiting for approximately 45 minutes until the lamp has cooled Unscrew the screws on the lamp cover Remove the lamp cover from the projector 2 Pull up the lamp cover pussing up the allow parts of the front panel lt Do not turn the power on with the lamp cover removed Do not insert your fingers between the lamp and the projector The sharp edges inside the projector may cause injuries Remove and dispose of the lamp protection film Loosen the screw that secures the lamp 10 11 12 13 Lift the handle so that it stands up Use the handle to slowly pull the lamp out of the projector Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector Do not place the lamp in locations where water might splash on it children can reach it or near flammable materials Do not insert your hands into the projector after the lamp is removed If you touch the optical components inside it could cause color unevenness and distortion of the projected images As shown in the figure lower the new lamp into the lamp compartment while aligning the lamp with the holes in the lamp compartment Make sure it fits in the projector Tighten the screw that secures the lamp Loos
32. New Zealand Sales Inquiries Phone 64 0 4 560 9100 Fax 64 0 4 560 9133 E mail projectorsales bdt co nz Technical Inquiries Phone 64 0 4 560 9100 Fax 64 0 4 560 9133 E mail service bdt co nz afa MITSUBISHI ELECTRIC CORPORATION 1 Zusho Baba Nagaokakyo City Kyoto Japan Ver 1
33. Q Q LO Os 2 16 9 Scales an image so that it is displayed in the center of the screen with a 16 9 aspect ratio This is most suitable for O gt pi O images which are already in a 16 9 aspect like high definition o o O O O O TV and 16 9 aspect DVD movies as it displays them without 16 9 picture aspect alteration 3 Real The image is projected as its original resolution and 5 5 resized to fit within the display area For input signals with O O lower resolutions the projected image will display smaller O lo O ol RO O than if resized to full screen You could adjust the zoom setting O gt or move the projector towards the screen to increase the image f O O O O E R 4 3 picture size if necessary You may also need to refocus the projector Nee p after making these adjustments E OTELO 16 9 picture 4 4 3 Scales an image so that it is displayed in the center of the screen with a 4 3 aspect ratio This is most suitable for 4 3 O gt O O FO O images like computer monitors standard definition TV and 4 3 lO O 2 aspect DVD movies as it displays them without aspect 4 3 picture O O HO O alteration 5 Full Scales an image to full screen size 16 10 The image is projected to fit all over screen EW331U ST only o Q Q 4 3 picture Oz fe O 16 9 picture C7 O O 16 10 picture Y Y Y EN 27 ENGLISH m Optimizing the image Selecting a picture mode EN 28
34. a product malfunction 4 If the projector is activated for the first time select your OSD language following the on screen instructions 5 Ifyou are prompted for a password press the arrow keys to enter a six digit password See Utilizing the password function on page 23 for details 6 Switch all of the connected equipment on 7 The projector will start to search for input signals The current input signal being scanned appears in the upper left corner of the screen If the projector doesn t detect a valid signal the message No Signal will be displayed until an input signal is found You can also press SOURCE on the projector or remote control to select your desired input signal See Switching input signal on page 24 for details CZ If the frequency resolution of the input signal exceeds the projector s operating range you will see the message Out of Range displayed on a blank screen Please change to an input signal which is compatible with the projector s resolution or set the input signal to a lower setting See Timing chart on page 56 for details MENUIEXIT Please select language English 20 Fran ais Svenska Deutsch T rk e Italiano e tina Espa ol Portugu s Pycckn Iny mpar Polski mpr Magyar g daud EN 21 ENGLISH m Using the menus The projector is equipped with On Screen Display OSD menus for making various adjustments and settings Below is the
35. age 32 for details Standby Monitor Out Selecting On enables the function The projector can output a VGA signal when it is in standby mode and the COMPUTER 1 and MONITOR OUT jacks are correctly connected to devices See Connecting a monitor on page 17 for how to make the connection CF Enabling this function slightly increases the standby power consumption When the projector enters standby mode the Video will be interrupted briefly This is not a product malfunction Menu Settings Menu display time Sets the length of time the OSD will remain active after your last key press The range is from 5 to 30 seconds in 5 second increments Menu position Sets the On Screen Display OSD menu position Lamp Settings Lamp mode See Setting Lamp mode as Low on page 48 for details Reset lamp timer See Resetting the lamp timer on page 51 for details Equivalent lamp hour See Getting to know the lamp hour on page 48 for details on how the total lamp hour is calculated EN 45 FUNCTION DESCRIPTION Change password You will be asked to enter the current password before changing to a Security Settings NEW ODEs Power on lock See Utilizing the password function on page 23 for details Closed Caption Enable Activates the function by selecting On when the selected input signal carries closed captions e Captions An on screen display of the dialogue narration and sound effects of TV prog
36. big angle EN 34 If you are viewing the screen at big angle you may not be able to view 3D contents correctly If you are not viewing 3D contents correctly check to see if the electronic shutter glasses are powered on or adequately charged See the instruction manual of the electronic shutter glasses for more information With the 3D option set to On contents displayed on the projector appear darker It is normal and does not mean the projector is malfunctioning With the 3D option set to On the black parts of image become slightly brighter It is normal and does not mean the projector is malfunctioning The following features cannot be used when viewing 3D contents on the projector Magnify Setting Brightness Contrast Color Tint Sharpness BrilliantColor Color Temperature 3D Color Management It may occur that the image may not be enough 3D image because setting such as fluorescent lighting may occur loss of synchronism of glasses 3D image may not appear on the screen depending on the PC performance such as graphics board memory or CPU The signals in the below table can be displayed with viewing 3D Contents on the projector If a different signal is fed the projector shows no 3D contents even with the 3D option set to On in the DISPLAY menu Mode Resolution H x V E o E i T ii TV60 480i 525i 15 73 59 94 VGA60 640 x 480 31 4
37. bles are properly connected The web page is not shown in the web browser or the web page is not responding Reload the page to see the data after changing on the screen If the page is not showing the modified data check the IP address of projector and log in again Specifications Projector specifications gt All specifications are subject to change without notice General Product name DLP Projector Model name EX321U ST EW331U ST Optical Resolution 1024 x 768 XGA 1280 x 800 WXGA Display system 1 CHIP DMD Lens F Number F 2 6 f 6 9 mm Lamp 230 W lamp Electrical Power supply AC100 240V 50 60 Hz Automatic Power consumption 3 3 A 330 W Max lt 0 5 W Standby When setting is Standby Monitor Out Off Standby Audio Out Off LAN Control Settings Off Mechanical Dimensions 282 mm W x 92 mm H x 229 mm D Not including protrusion Weight 2 9 Kg 6 lbs Input terminal Computer input RGB input D Sub 15 pin female x 2 Video signal input S VIDEO Mini DIN 4 pin port x 1 VIDEO RCA jack x 1 SD HDTV signal input Analog D Sub lt gt Component RCA jack x 3 through RGB input Digital HDMI Audio signal input PC audio jack x 1 Share the terminal with computer and video inputs Output terminal RGB output D Sub 15 pin female x 1 Audio signal output PC au
38. cket of the Video source device Connect the other end of the Video cable to the VIDEO socket on the projector If you wish to make use of the projector speaker in your presentations take a suitable audio cable and connect one end of the cable to the audio output jack of the computer and the other end to the AUDIO IN jack of the projector If you wish you can use another suitable audio cable and connect one end of the cable to the AUDIO OUT jack of the projector and the other end to your external speakers not supplied Once connected the audio can be controlled by the projector On Screen Display OSD menus See Adjusting the sound on page 32 for details The final connection path should be like that shown in the following diagram Video cable option Speakers Audio cable option AV device Audio cable option If the selected video image is not displayed after the projector is turned on and the correct video source has been selected check that the Video source device is turned on and operating correctly Also check that the signal cables have been connected correctly You need only connect to this device using a composite Video connection if Component Video and S Video inputs are unavailable for use See Connecting Video source devices on page 17 for details Operation Starting up the projector 1 Plug the power cord into the projector and into a wall socket Turn on the wal
39. ct keystoning at the bottom of the image AN You can correct the vertical keystones However their adjustment ranges are limited in such correction Press w A Pressa V When the keystone adjustment is carried out the adjustment value is indicated Note that this value doesn t mean a projection angle EN 25 The allowable range of the adjustment value in the keystone adjustment varies depending on the installation conditions Images may not be projected in a shape of a regular rectangle or with its aspect ratio 4 3 depending on the installation conditions of the projector and the screen When the keystone adjustment takes effect the resolution decreases In addition stripes may appear or straight lines may bend in images with complicated patterns They are not due to product malfunctions Noise may appear on the screen during the keystone adjustment because of the type of the video signal being projected and the setting values of the keystone adjustment In such cases set the keystone adjustment values in the range where the image is displayed without noise When the keystone adjustment is carried out the image may not be displayed correctly because of the type of input signal Magnifying and searching for details If you need to find the details on the projected picture magnify the picture Use the direction arrow keys for navigating the picture 1 2 Oo Using the remote control Press MAGNIFY
40. dio jack x 1 Share the terminal with computer and video inputs Speaker output 10W x 1 Control terminal Serial control D Sub 9 pin Male x 1 LAN control RJ 45 x 1 Environmental requirements Operating temperature 5 C 35 C without condensation Operating relative humidity 30 90 without condensation EN 55 ENGLISH m Dimensions 282 mm W x 92 mm H x 229 mm D Not including protrusion 229 Tolerance 2mm Timing chart Supported timing for PC input Resolution Mode vertical a ei ee Clock MHz 720 x 400 720 x 400_70 70 087 31 469 28 3221 VGA_60 59 940 31 469 25 175 VGA_72 72 809 37 861 31 500 640 x 480 VGA_75 75 000 37 500 31 500 VGA_85 85 008 43 269 36 000 VGA_120 119 518 61 910 52 500 SVGA_60 60 317 37 879 40 000 SVGA_72 72 188 48 077 50 000 SVGA_75 75 000 46 875 49 500 peewee SVGA_85 85 061 53 674 56 250 SVGA_120 119 854 77 425 83 000 SVGA_120 119 972 76 302 73 250 XGA_60 60 004 48 363 65 000 XGA_70 70 069 56 476 75 000 1024 x 768 XGA_75 75 029 60 023 78 750 XGA_85 84 997 68 667 94 500 XGA_120 119 804 98 958 137 750 1280 x 800 WXGA_60 59 81 49 702 83 500 WXGA_120 119 909 101 563 146 25 SXGA_60 60 020 63 981 108 000 1280 x 1024 SXGA_75 75 025 79 976 135 000 SXGA_85 85 024 91 146 157 500 1280 x 960_60 60 000 60 000 108 1280 x 960 1280 x 960_85 85 0
41. duces a strong magnetic field Also refrain from installing the projector near any cable carrying a large amount of current Place the projector on a solid vibration free surface Otherwise it may fall causing serious injury or damage e Do not stand the projector on its end It may fall causing serious injury or damage Slanting the projector more than 10 right and left or 15 front and rear may cause trouble or explosion of the lamp Do not place the projector near air conditioning unit heater or humidifier to avoid hot or moist air to the exhaust and ventilation hole of the projector e Be sure to use this projector at an altitude of less than 1500 meters COMPLIANCE NOTICE OF FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or m
42. e the sharper the picture becomes The lower the value the softer the picture becomes Adjusting BrilliantColor Highlight BrilliantColor in the PICTURE menu and select by pressing lt gt on the projector or remote control This feature utilizes a new color processing algorithm and system level enhancements to enable higher brightness while providing truer more vibrant colors in picture It enables a greater than 50 brightness increase in mid tone images which are common in video and natural scenes so the projector reproduces images in realistic and true colors If you prefer images with that quality select On If you don t need it select Off On is the default and recommended selection for this projector When Off is selected the Color Temperature function is not available Selecting a Color Temperature Highlight Color Temperature in the PICTURE menu and adjust the values by pressing lt on the projector or remote control The options available for color temperature settings vary according to the signal type selected 1 T1 With the highest color temperature T1 makes the image appear the most bluish white than other settings 2 T2 Makes images appear bluish white 3 T3 Maintains normal colorings for white 4 T4 Makes images appear reddish white About color temperatures There are many different shades that are considered to be white for various purposes One of the common methods of representing white co
43. e screw may cause a bad connection which could result in malfunction Do not over tighten the screw Ensure the handle is fully laid flat and locked in place Place the lamp protection film supplied with the new lamp on the lamp compartment As shown in the figure replace the lamp cover on the projector Tighten the screws that secure the lamp cover Loose screw may cause a bad connection which could result in malfunction Do not over tighten the screws Restart the projector Do not turn the power on with the lamp cover removed Resetting the lamp timer 14 After the startup logo open the On Screen Display OSD menu Go to the SYSTEM SETUP Advanced gt Lamp Settings menu Press MODE ENTER The Lamp Settings page is displayed Press Y to highlight Reset lamp timer and press MODE ENTER A warning message is displayed asking if you want to reset the lamp timer Highlight Reset and press MODE ENTER The lamp time will be reset to 0 EN 51 ENGLISH m EN 52 Do not reset if the lamp is not new or replaced as this could cause damage This projector uses a lamp that contains mercury Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations For disposal or recycling information please contact your local authorities or the Electronic Industries Alliance www eiae org For US only Indicators Light Status amp Descriptio
44. e while searching for details Selecting the aspect ratio The aspect ratio is the ratio of the image width to the image height Most analog TV and computers are in 4 3 ratio and digital TV and DVDs are usually in 16 9 ratio EN 26 With the advent of digital signal processing digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal To change the projected image ratio no matter what aspect the source is l 2 3 Press MENU EXIT and then press lt P gt until the DISPLAY menu is highlighted Press W to highlight Aspect Ratio Press lt p gt to select an aspect ratio to suit the format of the video signal and your display requirements About the aspect ratio C In the pictures below the black portions are inactive areas and the white portions are active areas OSD menus can be displayed on those unused black areas EX321U ST EW331U ST 1 Auto Scales an image proportionally to fit the projector s 5 5 O O O O native resolution in its horizontal width or its vertical height O gt C This is suitable when you want to make most use of the screen O A 4 3 picture O O O Q without altering the image s aspect ratio O ees 5 5 o 7 OJ CO 16 9 picture 2 2 O X0 O O O O SaS 16 10 picture
45. ect a suitable color space his function is only available when the H I input port is in use EN Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick release adjuster foot and 1 rear adjuster foot These adjusters change the image height and projection angle To adjust the projector ENGLISH m 1 Press the quick release button and lift the front of the projector Once the image is positioned where you want it release the quick release button to lock the foot in position 2 Screw the rear adjuster foot to fine tune the horizontal angle To retract the foot hold up the projector while pressing the quick release button then slowly lower the projector Screw the rear adjuster foot in a reverse direction If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other the projected image becomes trapezoidal To correct this situation see Correcting keystone on page 25 for details AN Do not look into the lens while the lamp is on The strong light from the lamp may cause damage to your eyes Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from Auto adjusting the image In some cases you may need to optimize the picture quality To do this press AUTO on the projector or remote control Within 3 seconds the built in Intelligent Auto Adjustment function will re adju
46. enu after you turn the projector on For ceiling mounting you need the ceiling mount kit designed for this projector Ask a specialist for installation For details consult your dealer A The warranty on this projector does not cover any damage caused by use of any non recommended ceiling mount kit or installation of the ceiling mount kit in an improper location When the projector is mounted on the ceiling images may appear darker than those projected in the case of tabletop mounting This isn t a product malfunction Be sure to use this projector at an altitude of less than 1500 meters Installation must be done by a qualified professional When the projector is installed on the ceiling using the ceiling mount kit it is recommended to hold the mount kit and the projector using metal bars or wires in addition to the mount kit fixing screws to prevent the projector from falling due to an earthquake or other cause For that purpose use metal bars wires or screws that bear a load of at least 70 kgf When using metal wires secure one end to a screw hole marked with an arrow on the rear terminal panel and the other end to the mount kit Do not use screw holes without arrow marks In this case make sure that the screws are inserted in the projector at least 5 mm The length of the screws should be 20 mm or shorter Also make sure that no electrical current is flowing in the mount kit due to current leakage or other cause
47. gram type See Selecting a picture mode on page 28 for details Adjusts the brightness of the image See Adjusting Brightness on page Brightness 29 for details Adjusts the degree of difference between dark and light in the image See Contrast Adjusting Contrast on page 29 for details Color Adjusts the color saturation level the amount of each color in a video image See Adjusting Color on page 29 for details Adjusts the red and green color tones of the image See Adjusting Tint Tint on page 29 for details c The function is only available when Video or S Video with NTSC system is selected Sharpness Adjusts the image to make it look sharper or softer See Adjusting Sharpness on page 29 for details BrilliantColor Color Temperature 3D Color Management Save Settings Adjusts white peaking while maintaining correct color presentation See Adjusting BrilliantColor on page 29 for details See Selecting a Color Temperature on page 29 for details See 3D Color Management on page 30 for details Saves the settings made for User 1 or User 2 mode oo Quick Auto Search See Switching input signal on page 24 for details nuew AJDYNOS Color Space Conversion See Changing Color Space on page 24 for details EN 44 nusw s1seg dNLAS WALSAS r nuswW PsdueAPY dNLAS WALSAS S FUNCTION Presentation Timer DESCRIPTION Reminds the presenter to finish the presentation within a certain time f
48. guards Please read all these instructions regarding your projector and retain 12 them for future reference Follow all warnings and instructions marked on the projector 1 10 11 Read instructions 13 All the safety and operating instructions should be read before the appliance is operated Retain instructions The safety and operating instructions should be retained for future reference 14 Warnings All warnings on the appliance and in the operating instructions should be adhered to 15 Instructions All operating instructions must be followed Cleaning Unplug this projector from the wall outlet before cleaning it Do not use liquid aerosol cleaners Use a damp soft cloth for clean ing Attachments and equipment Never add any attachments and or equipment without the approval of the manufacturer as such additions may result in the risk of fire electric shock or other personal injury Water and moisture Do not use this projector near water or in contact with water Accessories Do not place this projector on an unstable cart stand tripod bracket or table Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the projec tor Any mounting of the appliance should follow the manufac 16 turer s instructions and should use a mounting accessory recommended by the manufacturer LRAT An appliance and cart combination should be moved with care Qu
49. he air outlet grilles because they become hot during operation The heated air outlet grilles and bottom plate may cause injury or damage to other equip ment Also do not put the projector on a desk that is easily affected by heat Do not look into the air outlet grilles when projector is operating Heat dust etc may blow out of them and hurt your eyes Do not block the air inlet and outlet grilles If they are blocked heat may be generated inside the projector caus ing deterioration in the projector quality and fire Do not use flammable solvents benzene thinner etc and flammable aerosols near the projector Flammable substances may ignite causing fire or breakdown because the temperature inside the projector rises very high while the lamp is illuminating Do not use the projector with condensation on it It can lead to breakdown or other failure Place of installation For safety s sake do not use the projector at any place subjected to high temperature and high humidity Please maintain an operating tem perature humidity and altitude as specified below e Operating temperature between 41 F 5 C and 95 F 35 C e Operating humidity between 30 and 90 e Never put any heat producing device under the projector to prevent the projector from being overheated e Do not install the projector at a place that is unstable or subject to vibration e Do not install the projector near any equipment that pro
50. he bo Spare lamp VL E i EN ower cord is provided appropriately to the place of destination Mitsubishi Projector Warranty Sales Support and Service Information North America MEVSA Mitsubishi Electric Visual Solutions America Inc Presentation Products Division 9351 Jeronimo Road Irvine CA 92618 USA For Warranty Registration visit http www mitsubishi presentations com under Customer Care Sales amp Inquiries Phone _ Toll Free 888 307 0349 E mail ppdinfo mdea com Technical Inquiries Phone Toll Free 888 307 0309 E mail TSUPPORT mdea com MESCA Mitsubishi Electric Sales Canada Inc http www mitsubishielectric ca Information Technologies Group 4299 14th Avenue Markham Ontario L3R 0J2 Canada Sales amp Technical Inquiries Phone 1 800 450 6487 Fax 1 905 475 7958 E mail _ projectors mitsubishielectric ca Customer Care E mail support mitsubishielectric ca Europe MEU FRA Mitsubishi Electric Europe B V French Branch 25 Boulevard des Bouvets 92 741 Nanterre CEDEX France Sales Inquiries Phone 33 0 1 55 68 55 53 Fax 33 0 1 55 68 57 31 Technical Inquiries Phone 33 0 1 55 68 56 42 Fax 33 0 1 55 68 57 31 MEU GER Mitsubishi Electric Europe B V German Branch http www mitsubishi evs de Gothaer Strasse 8 40880 Ratingen Germany Sales Inquiries Phone 0049 2102 486 9250 Fax 0049 2102 486 7320 Technical Inquiries Phone 0
51. hen you use a longer RGB cable instead of the provided cable the image may not be projected correctly Some computers require additional connectors or analog RGB output adapters to be connected with this projector EN 16 Connecting a monitor If you want to view your presentation close up on a monitor as well as on the screen you can connect the MONITOR OUT signal output jack on the projector to an external monitor following the instructions below ENGLISH To connect the projector to a monitor 1 Connect the projector to a computer as described in Connecting a computer on page 16 2 Connect the RGB cable from the monitor to the MONITOR OUT jack of the projector Notebook or desktop computer jo 6G Hjo eo COMPUTER compuTeR 2 D AUDIO IN auDio out D S VIDEO Cc Once the Standby Monitor Out function is on the projector can output a VGA signal when it is in standby mode and an appropriate D Sub input is made to the COMPUTER 1 jack Images may not be displayed correctly depending on the type of the input signal See the instruction manual of the monitor Images may not be displayed correctly depending on the type of the cable Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets e HDMI e Component Video e S Video Video composite You need
52. ick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn Ventilation Slots and openings in the cabinet are provided for ventilation ensuring reliable operation of the projector and to protect it from overheating Do not block these openings or allow them to be blocked by placing the projector on a bed sofa rug or bookcase Ensure that there is adequate ventilation and that the manufac turer s instructions have been adhered to Power sources This projector should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power please consult your appliance dealer or local power company Power cord protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to cords at plugs convenience recepta cles and points where they exit from the appliance Do not put the power cord under a carpet Overloading Do not overload wall outlets and extension cords as this can result in a fire or electric shock Objects and liquids Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the projector Servicing Do not attempt to service this projector yourself Refer all servic ing to
53. if the projector will not be used in an extended period of time Cy To protect the lamp the projector will not respond to any commands during the cooling process To shorten the cooling time you can also activate the Quick Cooling function See Quick Cooling on page 45 for details Do not unplug the power cord before the projector shutdown sequence is complete or during the 90 second cooling down process If the projector is not properly shut down to protect the lamp when you attempt to re start the projector the fans will run for a few minutes to cool down Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange POWER TEMP LAMP Direct power off 1 The AC power cord can be pulled out during the projector is on To protect the lamp wait about 10 minutes before re starting the projector When you attempt to re start the projector the fans may run for a few minutes to cool down In such cases press POWER again to start the projector after the fans stop and the POWER indicator light turns orange 2 To protect the lamp do not shut down the projector while the POWER indicator light is blinking green after the lamp lights up 3 Before shutting down the projector be sure to close the menu screen If you shut down the projector without closing the menu the setting data of the menu may not be saved 4 Ifyou shut down the projector while controlling the
54. ing See Setting the presentation timer on page 31 for details TIMER SET UP Enters presentation timer setting directly See Setting the presentation timer on page 31 for details EN 9 Using the remote control for the first time Pull the tab before using the remote control Remote control effective range Infra Red IR remote control sensor is located on the front of the projector The remote control must be held at an angle within 30 degrees perpendicular to the projector s IR remote control sensor to function correctly The distance between the remote control and the sensor should not exceed 8 meters 26 feet Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra red beam Do not let the IR transmitter of the remote control be shined by sunlight or fluorescent lamps directly Please keep the remote controller away from fluorescent lamps for over 2 m or the remote controller might become malfunction If the remote control is close to Inverter Type fluorescent lamps it might become ineffective from time to time If the remote control and the projector are within a very short distance the remote control might become ineffective When you aim at the screen the effective distance is less than 5 m from the remote control to the screen and reflecting the IR beams back to the projector However the effective range might change according to
55. interval differs depending on the operating environment and may be shorter than 3500 5000 hours To keep the lamp life as long as possible you can do the following settings via the OSD menu Setting Lamp mode as Low Using Low mode reduces system noise and power consumption by 20 If the Low mode is selected the light output will be reduced and result in darker projected pictures Setting the projector in Low mode also extends the lamp operation life To set Low mode go into the SYSTEM SETUP Advanced gt Lamp Settings gt Lamp mode menu and press lt gt CG When this mode is switched the projected images may flicker EN 48 If this mode is frequently switched the lamp may be deteriorated Setting Auto Power Off This function allows the projector to turn off automatically if no input source is detected and no operation is made by user after a set period of time to prevent unnecessary waste of lamp life To set Auto Power Off go into the SYSTEM SETUP Basic gt Auto Power Off menu and press lt gt The time period can be set from 5 to 30 minutes in 5 minute increments If the preset time lengths are not suitable for your presentation select Disable The projector will not automatically shut down in a certain time period Timing of replacing the lamp When the lamp indicator lights up red or a message appears suggesting it is time to replace the lamp please install a new lamp or consult your dealer An old lamp may cau
56. isplayed Press A W until your desired signal is selected and pressM E E TER nce detected the selected source information will be displayed on the screen for seconds f there is multiple equipment connected to the projector repeat steps to search for another signal POWER TEMP LAMP MENUIEXIT Cc he brightness level of the projected image will change accordingly when you switch between different input signals ata graphic C presentations using mostly static images are generally brighter than Video using mostly moving OMP images movies he input signal type effects the options available for the Setting See Selecting a D picture mode on page for details he native display resolution of this projector is in a E 1 S 11 as E 1 S aspectratio or best display picture results you should select and use an input signal which outputs at this resolution Any other resolutions will be scaled by the projector depending upon the aspect ratio setting which may n o cause some image distortion or loss of picture clarity See Selecting the aspect ratio on page for details Changing Color S ace n the unlikely event that you connect the projector to a player via the projectors M input and the projected picture displays wrong colors please change the color space to YU Press ME UE Tand then press lt gt until the S URCE menu is highlighted Press W to highlight Color S ace Con ersion and press lt gt to sel
57. jecting as this could cause the blocking object to become heated and deformed or even cause a fire Locking control keys With the control keys on the projector locked you can prevent your projector settings from being changed accidentally by children for example When the Panel Key Lock is on no control keys on the projector will operate except d POWER 1 Press f on the projector or remote control or go to the SYSTEM SETUP Basic gt Panel Key Lock menu and select On by pressing lt 4 gt on the projector or remote control 2 A confirmation message is displayed Select Yes to confirm To release panel key lock press any key of the projector once to display the panel key lock warning With the warning being displayed press gt on the projector or remote control again Press and hold the key on the projector for 3 seconds You can also use the remote control to enter the SYSTEM SETUP Basic gt Panel Key Lock and press lt gt to select Off CG Keys on the remote control are still in use when panel key lock is enabled If you press POWER to turn off the projector without disabling panel key lock the projector will still be in locked status the next time it is turned on Freezing the image Cz Do not keep displaying a still picture for an extended period of time as the Press FREEZE on the remote control to freeze the image The word FREEZE will be displayed in the upper left corner of the screen To
58. l socket switch where fitted Check that the POWER indicator light on the projector lights orange after power has been applied A Ask your installation specialist to provide an Earth leakage breaker When you do not use the projector be sure to shut down the main power by the breaker Please use the original accessories e g power cord only with the device to avoid possible dangers such as electric shock and fire In order to ensure the safety in case of trouble with the projector use an electrical outlet having an earth leakage breaker to supply the power to the projector If you do not have such outlet ask your dealer to install it 2 Remove the lens cap If it is closed it could become deformed due to the heat produced by the projection lamp 3 Press POWER on the projector or remote control to start the projector The POWER indicator light flashes green and stays green when the projector is on The start up procedure takes about 30 seconds In the later stage of start up a startup logo is projected If necessary Rotate the focus ring to adjust the image clearness Cc If the projector is still hot from previous activity it will run the cooling fans for approximately 90 seconds before energizing the lamp To maintain the lamp life once you turn the projector on wait at least 5 minutes before turning it off After amp POWER is pressed the image may flicker before the lamp becomes stable This is not
59. like that shown in the following diagram Audio cable option Speakers ENGLISH omponent ideo to Sub adaptor cable option MONITOR putera SERIAL NTE COMPUTER AUBIN auoio out SVIDEO Audio cable option A device CF If the selected video image is not displayed after the projector is turned on and the correct video source has been selected check that the Video source device is turned on and operating correctly Also check that the signal cables have been connected correctly Connecting an S i eoso rce e ice amine your ideo source device to determine if it has an unused S ideo output socket available f so you can continue with this procedure f not you will need to reassess which method you can use to connect to the device To connect the rojector toanS i eoso rce e ice Take an S ideo cable and connect one end to the S ideo output socket of the ideo source device onnect the other end of the S ideo cable to the S E socket on the projector f you wish to make use of the projector speaker in your presentations take a suitable audio cable and connect one end of the cable to the audio output jack of the computer and the other end to the U jack of the projector f you wish you can use another suitable audio cable and connect one end of the cable to the U UT jack of the projector and the other end to your e ternal speaker
60. lor is known as the color temperature A white color with a low color temperature appears to be reddish white A white color with a high color temperature appears to have more blue in it EN 29 en 3D Color Management In most installation situations color management will not be necessary such as in classroom meeting room or lounge room situations where lights remain on or where building external windows allow daylight into the room Only in permanent installations with controlled lighting levels such as boardrooms lecture theaters or home theaters should color management be considered Color management provides fine color control adjustment to allow for more accurate color reproduction should you require it Proper color management can only be achieved under controlled and reproducible viewing conditions You will need to use a colorimeter color light meter and provide a set of suitable source images to measure color reproduction These tools are not provided with the projector however your projector supplier should be able to provide you with suitable guidance or even an experienced professional installer The Color Management provides six sets RGBCMY of colors to be adjusted When you select each color you can independently adjust its range and saturation according to your preference If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monit
61. n Power Temp Power events Orange Off Off Stand by mode Green Flashing Off Off Powering up Green Off Off Normal operation e The projector needs 90 seconds to cool down as it was abnormally shut Orange Flashing Off Red down without the normal cooling down process e The projector needs to cool for 90 seconds after the power is turned off Orange Flashing Off Off Cooling down Orange off Red The projector has shutdown automatically If you try to re start the projector it Flashing will shutdown again Please contact your dealer for assistance off off Red e The projector needs 90 seconds to cool down e Please contact your dealer for assistance Thermal events Off Red Off Off Red Red Off Red Green Red Red Red Red Red Green on a ee ee Green Red Green Orange Red Red Orange Red Green Off Green Red Off Green Green EN 53 ENGLISH Troubleshooting The projector does not turn on Cause Remedy There is no power from the power cable Plug the power cord into the AC inlet on the projector and plug the power cord into the power outlet If the power outlet has a switch make sure that it is switched on Attempting to turn the projector on again during the cooling process Wait until the cooling down process has completed No picture Cause Remedy The video source is not turned on or connected correctly The projector
62. n and confirm the new password by re entering the new password at the Confirm column To disable password protection uncheck the box v Once set access to the Tools page has been password protected Refer to step iv for how to use the password function CG After making the adjustments press the Send button and the data will be saved in the projector Once the password is set the Log Out button will display beside the Tools button Write down your selected password in advance or right after the password is entered so that it is available to you should you ever forget it If you forget the password you will not be able to log in The software is available in English language When DHOP is turned on there is a possibility of stopping the webpage connection If this happens please check the new IP address of the projector and enter the new address to connect again vi Press Exit to go back to the remote network operation page 4 The Info page displays the information and status of this projector em i The information you entered in the Tools page will display here and these columns are empty when you use e Control for the first time ii When the projector is in abnormal conditions the following information will display C7 When the projector is in normal conditions or in any abnormal conditions other than the ones mentioned below the Error Status column will be empty Error Status Description 3 Lam
63. n page 32 for details VOLUME keys Adjusts the sound level See Adjusting the sound on page 32 for details 10 11 13 14 MAGNIFY keys Magnifies or reduces the projected picture size See Magnifying and searching for details on page 26 for details MENU EXIT Turns on the On Screen Display OSD menu Goes back to previous OSD menu exits and saves menu settings See Using the menus on page 22 for details Keystone Arrow keys w A Up a WDown Manually corrects distorted images resulting from an angled projection See Correcting keystone on page 25 for details AUTO Automatically determines the best picture timings for the displayed image See Auto adjusting the image on page 25 for details gt Right Q Activates panel key lock See Locking control keys on page 32 for details When the On Screen Display OSD menu is activated the 3 8 and 10 keys are used as directional arrows to select the desired menu items and to make adjustments See Using the menus on page 22 for details SOURCE Displays the source selection bar See Switching input signal on page 24 for details MODE ENTER Depending upon which input signal is selected selects an available picture setup mode See Selecting a picture mode on page 28 for details ENGLISH m Enacts the selected On Screen Display OSD menu item TIMER ON Activates or displays an on screen timer based on your own timer sett
64. ndard specifications Version 1 0 Utilizing the password function To prevent unauthorized connection to the projector via PJLink application the projector includes an option for setting up password security To set the password 1 Aw C If you forget the password please use the password projectorcontroller Open the OSD menu and go to the SYSTEM SETUP Advanced gt LAN Control Settings menu Press MODE ENTER The LAN Control Settings page is displayed Highlight PJLink Certification and select On by pressing lt P gt The default password is admin Press W to highlight Change PJLink Password and press MODE ENTER Enter the current password Press lt to select the digit and press A W to select from 0 9 A Z a z or symbols Press MODE ENTER to confirm Enter the new password and Press MODE ENTER to confirm PJLink supported commands The table below shows commands to control the projector using the PJLink protocol Commend Description Remark Parameter POWR Power control 0 Standby 1 Power on POWR Inquiry about the power state 0 Standby 1 Power on 2 Cooling down 3 Warming up INPT Input switching 11 COMPUTER1 12 COMPUTER2 21 VIDEO INPT Inquiry about input switching 22 S VIDEO 31 HDMI AVMT Mute control 10 BLANK disable 11 BLANK enable 20 Audio mute disable AVMT Inquiry about the mute state 21 Audio mute enable 30 BLAN
65. ng a 4 3 aspect ratio 100 inch screen distance from the screen is 1 2 m and with a vertical offset of 23 cm EW331U ST For example if you are using a 16 10 aspect ratio 100 inch screen distance from the screen is 1 1 m and with a vertical offset of 7 cm If you place the projector in a different position to that recommended you will have to tilt it down or up to center the image on the screen In these situations some image distortion will occur Use the Keystone function to correct the distortion See Correcting keystone on page 25 for details How to determine the recommended screen size for a given distance This method can be used for situations where you have purchased this projector and would like to know what screen size will fit in your room The maximum screen size is limited by the physical space available in your room 1 Measure the distance between the projector and where you want to position the screen This is the projection distance 2 Refer to the table Standard or 16 9 and find the closest match to your measurement in the distance from the screen column If the min and max values are available on the table check that your measured distance is between the min and max distances listed on either side of the average distance value 3 Using this value look across that row to the left to find the corresponding Screen That is the projected image size of the projector at that projection distance 4 On that
66. oduct malfunction Personalizing the projector menu display The On Screen Display OSD menus can be set according to your preferences The following settings do not affect the projection settings operation or performance e Menu display time in the SYSTEM SETUP Advanced gt Menu Settings menu sets the length of time the OSD will remain active after your last key press The time length ranges from 5 to 30 seconds in 5 second increments Use lt P gt to select a suitable time frame e Menu position in the SYSTEM SETUP Advanced gt Menu Settings menu sets the OSD position in five locations Use lt gt to select a preferred position e Language in the SYSTEM SETUP Basic menu sets your familiar language for the OSD menus Use lt gt to select your language e Splash Screen in the SYSTEM SETUP Basic menu sets a preferred logo screen to be displayed during projector start up Use lt gt to select a screen Shutting down the projector 1 Press POWER and a confirmation message displays prompting you If you don t respond in a few seconds the message will disappear 2 Press POWER a second time The POWER indicator light flashes orange the projection lamp shuts down and the fans will continue to ran amp for approximately 90 seconds to cool down the projector 3 Once the cooling process finishes the POWER indicator lightisa steady orange and fans stop 4 Disconnect the power cord from the wall socket
67. ojection surface is not white See Using Wall Screen on page 30 for details Aspect Ratio There are four options to set the image s aspect ratio depending on your input signal source See Selecting the aspect ratio on page 26 for details Corrects any keystoning of the image See Correcting keystone on page Keystone 25 for details Displays the position adjustment page To move the projected image use was the directional arrow keys The values shown on the lower position of the Position page change with every key press you made until they reach their maximum or minimum Adjusts the clock phase to reduce image distortion Phase H Size Adjusts the horizontal width of the image Magnif Magnifies or reduces the projected image See Magnifying and gnity searching for details on page 26 for details This projector features a 3D function which enables you to enjoy 3D movies videos and sporting events in a more realistic way by presenting the depth of the images You need to wear a pair o asses to view the 3D he depth of the images Y d pair of 3D gl iew thi 3D images See Watching 3D Content on page 34 for details 3D Sync When you discover the inversion of the image depth enable this function to correct the problem EN 43 ENGLISH nuswW AYNLIId Z FUNCTION DESCRIPTION Pre defined picture modes are provided so you can optimize your Setting projector image set up to suit your pro
68. om digital cameras or DVs through the PC input for best viewing in a blackened little light environment For Video input signals this mode is suitable for enjoying dark movies or DVD movies best viewed in a blackened little light home cinema or lounge room environment User 1 User 2 mode Recalls the settings customized based on the current available picture modes See Setting the User 1 User 2 mode on page 28 for details Setting the User 1 User 2 mode There are two user definable modes if the current available picture modes are not suitable for your need You can use one of the picture modes except the User 1 User 2 as a starting point and customize the settings User 1 is for PC sources and User 2 is for VIDEO sources 1 2 3 4 pi Press MENU EXIT to open the On Screen Display OSD menu Go to the PICTURE gt Setting menu Press lt P gt to select User 1 to User 2 Press W to select a sub menu item to be changed and adjust the value with lt p gt See Fine tuning the image quality in user modes below for details When all settings have been done highlight Save Settings and press MODE ENTER to store the settings The confirmation message Setting Saved is displayed Fine tuning the image quality in user modes According to the detected signal type there are some user definable functions available when User 1 or User 2 mode is selected You can make adjustments to these functions based on your needs
69. on Use the attached RGB cable with this equipment so as to keep interfer ence within the limits of an FCC Class B device This apparatus must be grounded DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE CAUTION Not for use in a computer room as defined in the Standard for the Pro tection of Electronic Computer Data Processing Equipment ANSI NFPA 75 The attached power cord is to be used exclusively for this product Never use it for other products EN 2 When using the projector in Europe COMPLIANCE NOTICE This Projector complies with the requirements of the EC Directive 2004 108 EC EMC Directive and 2006 95 EC Low Voltage Direc tive The electro magnetic susceptibility has been chosen at a level that gains proper operation in residential areas on business and light industrial premises and on small scale enterprises inside as well as outside of the buildings All places of operation are characterized by their connection to the public low voltage power supply system WARNING Use the attached RGB cable with this equipment so as to keep interfer ence within the limits of an EN55022 Class B device When using the projector in South Korea WARNING Use the attached RGB cable with this equipment so as to keep interfer ence within the limits of a KO0022 Class B device Please follow WARNING instructions Note This symbol mark is for EU countries only This symbol mark is acco
70. only connect the projector to a Video source device using just one of the above connecting methods however each provides a different level of video quality The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below HDMI High Definition Multimedia Interface supports uncompressed video data transmission between compatible devices like DTV tuners DVD players and displays over a single cable It provides pure digital viewing experience See Connecting an HDMI device on page 18 for how to connect the projector to an HDMI device Digital TV tuner and DVD players output Component Video natively so if available on your devices this should be your connection method of choice in preference to composite Video See Connecting a Component Video source device on page 18 for how to connect the projector to a component video device If you have both composite Video and S Video output terminals on your Video source device you should elect to use the S Video option See Connecting an S Video source device on page 19 for how to connect the projector to an S Video device If you have only composite Video output terminals on your Video source device connect to Composite Video input See Connecting a composite Video source device on page 20 for how to connect the projector to a composite Video device EN 17 Connecting an HDMI device You should
71. ore of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced Radio TV technician for help Any changes or modifications not expressly approved by Mitsubishi could void the user s authority to operate this equipment COMPLIANCE NOTICE OF INDUSTRY CANADA This Class B digital apparatus complies with Canadian ICES 003 EN 6 Projector exterior view Front upper side Ee a w 1 External control panel See Projector on page 8 for details ENGLISH Front IR remote sensor Projection lens Vent air intake 2 Lamp cover 3 Vent heated air exhaust 4 Quick release button 5 Lens cover 6 Focus ring 7 8 9 Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns 10 RGB signal output socket 11 RGB PC Component Video YPbPr YCbCr signal input socket x 2 12 HDMI input port 13 Serial control port 14 LAN RJ 45 port 15 Audio input jack Audio output jack 16 S Video input socket Video input socket 17 Kensington lock 18 AC power cord inlet 19 Quick release foot 20 Security bar 21 Rear adj
72. ors TVs projectors etc You can project any image from the disc on the screen and enter the 3D Color Management menu to make adjustments To adjust the settings 1 Goto the PICTURE menu and highlight 3D Color Management 2 Press MODE ENTER and the 3D Color Management page is displayed 3 Highlight Primary Color and press lt P gt to select a color from among Red Green Blue Cyan Magenta or Yellow 4 Press W to highlight Hue and press lt P gt to select its range Increase in the range will include colors consisted of more proportions of its two adjacent colors Please refer to the illustration to the right for how the colors relate to each other For example if you select Red and set its range at 0 only pure red in the projected picture will be selected Increasing its range will include red close to yellow and red close to magenta 5 Press W to highlight Saturation and adjust its values to your preference by pressing lt gt Every adjustment made will reflect to the image Magenta immediately For example if you select Red and set its value at 0 only the saturation of pure red will be affected 6 Press W to highlight Gain and adjust its values to your preference by BLUE pressing lt gt The contrast level of the primary color you select will be affected Every adjustment made will reflect to the image immediately 7 Repeat steps 3 to 6 for other color adjustments 8 Make sure you have made all of the desired adjus
73. overview of the OSD menu Main menu icon Main menu Highlight Sub menu if oe Magnify 1D 30D Sync f Fress MENU to go Current input signal back to the previous page or to exit Below is an example about how to set the OSD language 1 Press MENU EXIT on the projector or remote 3 Press W to highlight Language and press lt gt control to turn the OSD menu on to select a preferred language 2 Use lt p gt to highlight the SYSTEM SETUP 4 Press MENU EXIT twice on the projector or Basic menu remote control to leave and save the settings The first press leads you back to the main menu and the second press closes the OSD menu EN 22 Utilizing the password function For security purposes and to help prevent unauthorized use the projector includes an option for setting up password security The password can be set through the On Screen Display OSD menu For details of the OSD menu operation please refer to Using the menus on page 22 CZ You will be inconvenienced if you activate the power on lock functionality and subsequently forget the password Print out this manual if necessary and write the password you used in this manual and keep the manual in a safe place for later recall Setting a password Cz Once a password has been set the projector cannot be used unless the correct password is entered every time the projector is started 1 Open the OSD menu and go
74. p fail The lamp fails to ignite or turns off during operation 3 Over Temp The projector temperature is too high or cannot be detected 3 Fan Lock The fan rotation speed cannot be set or detected 1 Over Lamp Usage time The lamp is still in use after the lamp warning messages display 3 Error 1 notice iii Press Exit to go back to the remote network operation page 5 After pressing the button Contact IT Help the HELP DESK window will appear at the upper right corner You will be able to deliver messages to RoomView software which is connected to the same local area network a For more information visit http www crestron com amp www crestron com getroomview Controlling the projector using PJLink application This projector supports standard protocol PJLink for projector control and you can control and monitor projector s operations using the same application among projectors of different models and different manufacturers About PJLink e To use PJLink function the PJLink application software is required EN 38 For the specifications of PJLink access to the Web site of Japan Business Machine and Information System Industries Association JBMIA http pjlink jbmia or jp english This projector is fully compliant to the specifications of JBMIA PJLink Class 1 It supports all the commands defined by PJLink Class 1 and the compliance has been verified with the PJLink sta
75. projector using the network function the application software such as e Control may fail In this case close the application software first After the connection between the projector and the computer re establishes initialize the software again EN 33 3D Watching 3D Content You can enjoy 3D Content with this projector In order to watch 3D Content you need to have the following items 1 Field sequential 3D video contents 2 DLP Link active electronic shutter glasses Field sequential The system which displays alternately the image for the left eye and the right eye 3D image Format Page Flipping Side by Side Top amp Bottom Checkerboard Field Sequential Not supported Not supported The shutter timing of shuttered glasses is controlled by being Sensor synchronized with switching of right and left 3D image which is detected by the sensor of glasses DLP Link active electronic shutter glasses DLP Projector Play the field sequential 3D video contents on a computer or DVD player and then connect the cable with the projector Go to the DISPLAY menu then set the 3D option to On Put on the electronic shutter glasses to watch the contents If the contents are not projected correctly go to the DISPLAY menu and switch the order of the image setting the 3D Sync CG Watch the contents in front of the screen not at
76. r 1 Take the supplied RGB cable and connect one end to the D Sub output socket of the computer 2 Connect the other end of the RGB cable to the COMPUTER 1 or COMPUTER 2 signal input socket of the projector 3 Ifyou wish to make use of the projector speaker in your presentations take a suitable audio cable and connect one end of the cable to the audio output jack of the computer and the other end to the AUDIO IN jack of the projector 4 Ifyou wish you can use another suitable audio cable and connect one end of the cable to the AUDIO OUT jack of the projector and the other end to your external speakers not supplied Once connected the audio can be controlled by the projector On Screen Display OSD menus See Adjusting the sound on page 32 for details The final connection path should be like that shown in the following diagram Audio cable option Notebook or desktop computer Speakers RGB cable Audio cable option CG eo eC jo COMPUTER COMPUTER2 C Many notebooks do not turn on their external video ports when connected to a projector Usually a key combo like FN F3 or CRT LCD key turns the external display on off Locate a function key labeled CRT LCD or a function key with a monitor symbol on the notebook Press FN and the labeled function key simultaneously Refer to your notebook s documentation to find your notebook s key combination A W
77. r Ceiling Front Ceiling Auto Power Off Disable 5 min 10 min 15 min 20 min 25 min 30 min Disable 5 min 10 min 15 min 20 min 2 SYSTEM SETUP Blank Timer a S a Ea Basic Panel Key Lock On Off Timer Controller tb min 1 hr 2 hr 3 hr 4 hr 8 hr 12 Splash Screen Black Blue MITSUBISHI Quick Cooling On Off Mute On Off Audio Settings Volume Standby Audio Out On Off Standby Monitor Out Off On Menu display time 5 sec 10 sec 15 sec 20 sec 25 sec 30 sec Menu Settings Center Top Left Top Right Bottom Right Menu position Bottom Lett Lamp mode Standard Low Lamp Settings Reset lamp timer Equivalent lamp hour 5 Secu Sates St n SUS TEM SETUR Closed Caption Advanced Closed caption Enable On Off Caption Version CC1 CC2 CC3 CC4 Control By RS 232C LAN PJLink Certification On Off Change PJLink Password DHCP On Off LAN Control Settings IP Address Subnet Mask Default Gateway DNS Server Apply Reset All Settings Source Setting 6 INFORMATION Current System Status Resolution Color System Equivalent Lamp Hour Note that the menu items are available when the projector detects at least one valid signal If there is no equipment connected to the projector or no signal detected limited menu items are accessible EN 42 Description of each menu nuswW AV 1dSId L FUNCTION Wall Screen DESCRIPTION Corrects the projected picture s color when the pr
78. rame See Setting the presentation timer on page 31 for details ENGLISH Language Projector Position Auto Power Off Sets the language for the On Screen Display OSD menus See Using the menus on page 22 for details See Choosing a location on page 11 for details Allows the projector to turn off automatically if no input signal is detected and no operation is made by user after a set period of time See Setting Auto Power Off on page 48 for details Blank Timer Sets the image blank time when the Blank feature is activated once elapsed the image will return to the screen See Hiding the image on page 32 for details Panel Key Lock Disables or enables all panel key functions except POWER on the projector and keys on the remote control See Locking control keys on page 32 for details Timer Controller Sets the auto shutdown timer The timer can be set to a value between 30 minutes and 12 hours Splash Screen Quick Cooling Allows you to select which logo screen will be displayed during projector start up Three options are available MITSUBISHI logo Black screen or Blue screen Selecting On enables the function and the projector cooling time will be shortened to a few seconds ea If you attempt to restart the projector right after the quick cooling process it may not be turned on successfully and will rerun its cooling fans Audio Settings See Adjusting the sound on p
79. rams and videos that are closed gt a Closed Caption captioned usually marked as CC in TV listings a lt cr When the projector displays OSD or any dialog captions are not S 7 displayed at the same time sa 9 m Caption Version a Selects a preferred closed captioning mode To view captions select 3 u CC1 CC2 CC3 or CC4 CC1 displays captions in the primary language in your area S If you are using a LAN cable for connection see Supervising and E controlling by computer on page 36 for details If you are using a RS 232C cable for connection go to the SYSTEM SETUP Advanced gt LAN Control Settings gt Control By menu and LAN Control Settings select RS 232C And press Apply to save the settings cr LAN and RS 232C function cannot work spontaneously If you are using the PJLink application see Controlling the projector using PJLink application on page 38 for details Returns all settings to the factory preset values Reset All Settings CF The following settings will still remain Phase H Size User 1 User 2 Language Projector Position Security Settings Source Shows the current signal source gt Setting Shows the selected mode in the PICTURE menu 390 Resolution I Current System Status F i Shows the native resolution of the input signal gt a Color System 9 Shows input system format NTSC PAL SECAM or RGB Equivalent Lamp Hour Displays the number of hours the lamp has been used
80. rding to the directive 2002 96 EC Article 10 Information for users and Annex IV and or to the directive 2006 66 Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and or reused This symbol means that electrical and electronic equipment batteries and accumula tors at their end of life should be disposed of separately from your household waste If a chemical symbol is printed beneath the symbol shown above this chemical sym bol means that the battery or accumulator contains a heavy metal at a certain concen EC Article 20 Information for end users and Annex ll tration This will be indicated as follows Hg mercury 0 0005 Cd cadmium 0 002 Pb lead 0 004 In the European Union there are separate collection systems for used electrical and electronic products batteries and accumulators Please dispose of this equipment batteries and accumulators correctly at your local community waste collection recycling centre Please help us to conserve the environment we live in WARNING The lens cap is for protecting the lens If you leave the lens cap on the lens with the projector turned on it may be deformed because of heat build up Remove the lens cap when you turn on the projector One of power cords for the U S Europe Indonesia U K Australia South Korea and Argentina is provided appropriately This projector uses the power plug
81. rence will dictate which installation location you select Take into consideration the size and position of your screen the location of a suitable power outlet as well as the location and distance between the projector and the rest of your equipment Your projector is designed to be installed in one of the possible installation locations 1 Front Table Select this location with the projector placed near the floor in front of the screen This is the most common way to position the projector for quick setup and portability 3 Rear Ceiling Select this location with the projector suspended upside down from the ceiling behind the screen 2 Select this location with the projector placed near the floor behind the screen Note that a special rear projection screen is required Set Rear Table in the SYSTEM SETUP Basic gt 4 Projector Position menu after you turn the projector on Note that a special rear projection screen and qualified projector ceiling mount kit are required for this installation location Rear Table Set Rear Ceiling in the SYSTEM SETUP Basic gt Projector Position menu after you turn the projector on Front Ceiling Select this location with the projector suspended upside down from the ceiling in front of the screen Purchase a qualified projector ceiling mount kit from your dealer to mount your projector on the ceiling Set Front Ceiling in the SYSTEM SETUP Basic gt Projector Position m
82. ring input source switching During command processing During AUTO execution Before the splash screen disappears after the power is turned on Use 1 computer to control monitor 1 projector For how to control monitor using PJLink see the operation manual of the PJLink application you use When you monitor the projector s operating state using this function by issuing inquiry commands successively issue an inquiry command after receiving the response to the previous inquiry command from the projector How to Use Network Function When connecting a computer and projector with LAN configure the both IP Addresses in the same network group Configure the IP CONFIG correctly If the settings are not correct the communication may be unavailable For the detail consult the network administrator When the Control By in the SYSTEM SETUP Advanced gt LAN Control Settings menu is selected RS 232C the LAN Control Settings function is not available Glossary For more detail of the glossary below refer to the technical book that is commercially available Term Description DHCP Abbreviation for Dynamic Host Confi guration Protocol This protocol automatically assigns IP Address to networked devices IP Address Numerical address to identify networked computers Subnet Mask A numeric value to defi ne the number of bits used for a network address of a divided network or subnet in an IP Address Default Gateway A server
83. rmally Out of Lamp Usage Time EN 49 ENGLISH m Replacing the lamp Spare lamp for EX321U ST EW331U ST VLT EX320LP AN EN 50 Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector Contact your dealer for purchase of the lamp To reduce the risk of electrical shock always turn the projector off and disconnect the power cord before changing the lamp To reduce the risk of severe burns allow the projector to cool for at least 45 minutes before replacing the lamp To reduce the risk of injuries to fingers and damage to internal components use caution when removing lamp glass that has shattered into sharp pieces To reduce the risk of injuries to fingers and or compromising image quality by touching the lens do not touch the empty lamp compartment when the lamp is removed Be sure to install the lamp securely When the lamp isn t installed properly it won t illuminate Improper installation may also result in fire If the lamp should break never shake the lamp box or hold it in front of your face after removing it The glass fragments may fall out and cause injury to your eyes In the event that the high pressure mercury lamp exploded glass fragments may have been scattered inside the projector Ask your dealer to replace the lamp and to inspect the inside of the projector When you clean or replace the lamp by yourself be sure to hold the handle of the
84. s not supplied nce connected the audio can be controlled by the projector n Screen isplay S menus See Adjusting the sound on page for details The final connection path should be like that shown in the following diagram Speakers S ideo cable option Audio cable option Gio Eo jo eG amp COMPUTER 1 COMPUTER Audio cable 2 ti A device a Cc If the selected video image is not displayed after the projector is turned on and the correct video source has been selected check that the Video source device is turned on and operating correctly Also check that the signal cables have been connected correctly If you have already made a Component Video connection between the projector and this S Video source device you need not connect to this device using an S Video connection as this makes an unnecessary second connection of poorer picture quality See Connecting Video source devices on page 17 for details EN 19 Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available If so you can continue with this procedure If not you will need to reassess which method you can use to connect to the device To connect the projector to a composite Video source device 1 2 3 EN 20 Take a Video cable and connect one end to the composite Video output so
85. screens Replacing the remote control battery 1 gt Please follow the illustrated instructions Push and hold the locking arm while pulling out the battery holder 2 EN 10 Pull out the battery holder Insert the new battery in the holder Note the positive polarity should face outward Push the holder into the remote control Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions Use of a battery of wrong type may cause explosion Use Lithium coin battery type CR2025 only Dispose of used batteries according to your local regulations Discard used battery promptly Batteries may explode if mistreated Do not recharge disassemble or dispose of in fire Be careful in handling the battery according to the instructions Load the battery with its positive and negative sides correctly oriented as indicated on the remote control Keep batteries out of reach of children and pets Remove the battery if the remote control is not used for a long time Keep battery in original package until ready to use Never put battery in mouth for any reason as it can easily be accidentally swallowed If battery is accidentally swallowed contact your physician or your poison control center Dispose of the used battery with cellophane tape wrapping both ends of it Positioning your projector Choosing a location Your room layout or personal prefe
86. se a malfunction in the projector and in some instances the lamp may explode The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too hot Turn the power off and let the projector cool for 45 minutes If the Lamp or LAMP indicator light still lights up after turning the power back on please contact your dealer See Indicators on page 53 for details The following lamp warning displays will remind you to change the lamp Status Message The lamp has been in operation for 3750 hours Install a new lamp for optimal performance If the projector is normally run with Low selected See Setting Lamp mode as Low on page 48 you may continue to operate the projector until the 4750 hour lamp warning appears Order Replacement Lamp Lamp gt 3750 Hour The lamp has been in operation for 4750 hours A new lamp should be fitted to avoid the inconvenience when the projector runs out of lamp time Replace Lamp soon The lamp has been in operation for 5000 hours It is strongly recommended that you replace the lamp at this age S Now The lamp is a consumable item The lamp brightness diminishes with use ced A This is normal lamp behavior You can replace the lamp whenever you notice that the brightness level has significantly diminished If the lamp is not replaced beforehand it must be replaced after 5000 hours usage The lamp MUST be replaced before the projector will operate no
87. splay wrong colors for about 1 second This is not product malfunction Connecting a Component Video source device Examine your Video source device to determine if it has a set of unused Component Video output sockets available EN 18 If so you can continue with this procedure If not you will need to reassess which method you can use to connect to the device To connect the projector to a Component Video source device 1 Take a Component Video to RGB D Sub adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device Match the color of the plugs to the color of the sockets green to green blue to blue and red to red Connect the other end of the Component Video to RGB D Sub adaptor cable with a D Sub type connector to the COMPUTER 1 or COMPUTER 2 socket on the projector If you wish to make use of the projector speaker in your presentations take a suitable audio cable and connect one end of the cable to the audio output jack of the computer and the other end to the AUDIO IN jack of the projector If you wish you can use another suitable audio cable and connect one end of the cable to the AUDIO OUT jack of the projector and the other end to your external speakers not supplied Once connected the audio can be controlled by the projector On Screen Display OSD menus See Adjusting the sound on page 32 for details The final connection path should be
88. st the values of Frequency and Clock to provide the best picture quality The current source information will be displayed in the upper left corner of the screen for 3 seconds Cr The screen will be blank while AUTO is functioning This function is only available when a PC signal analog RGB is selected Fine tuning the image size and clarity In the right figure A Focus Ring 1 Adjust Focus using A Focus Ring 2 Move the product back and forth to adjust the screen size 3 Adjust Focus again if necessary POWER TEMP _LAMP af MITSUBISHI QE Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom It occurs when the projector is not perpendicular to the screen To correct this besides adjusting the height of the projector you will need to manually correct it following one of these steps e Using the remote control Press w m on the projector or remote control to display the Keystone correction page Press w to correct keystoning at the top of the image Press to correct keystoning at the bottom of the image POWER TEMP LAMP e Using the OSD menu 1 Press MENU EXIT and then press lt gt until the DISPLAY menu is ome highlighted 2 Press W to highlight Keystone and press MODE ENTER The fs Ser Keystone correction page is displayed 3 Press w to correct keystoning at the top of the image or press to corre
89. sword You have successfully assigned a new password to the projector member to enter the new password ne ttime the projector is started To leave the S menu pressME UE T isabling the ass or nction To disable password protection go back to the SYSTEM SETUP ance gt Sec rit Settings Po er on loc menu after opening the S menu system Select by pressing lt The message PUTP SS R is displayed nter the current password 7 f the password is correct the S menu returns to the Sec rit Settings page with shown in the row of Po eronloc You will not have to enter the password ne t time you turn on the projector e f the password is incorrect the password error message is displayed lasting for three seconds and the message PUTP SS R is displayed for your retry You can press ME UE T to cancel the change or try another password C7 hough the password function is disabled you need to keep the old password in hand should you ever need to re activate the password function by entering the old password S itchingin t signal The projector can be connected to multiple devices at the same time owever it can only display one full screen at a time e sure the ic to Search function in the S URCE menuis n which is the default of this projector if you want the projector to automatically search for the signals You can also manually cycle through the available input signals Press S URCE on the projector or remote control A source selection bar is d
90. t Snoen aa A ECEE E E OET E EEEE NE SEE ARTE REE ANENE 47 Lampinformatiois es seu cs sain sie even e 0k ei eesi e aS A E tbe EEEE a CiS EEES EEEE ECELAS 48 Indicators MOU ESO OE t 35s sees cas ene a need cates E S E A E SEENA 54 Sp cificati ons ssania as eiei E AEE RE EAEE EEA EERENS Ei SEASSA AA E EE 55 Declaration of Conformity Model Number EX321U ST EW331U ST Trade Name MITSUBISHI ELECTRIC Responsible party Mitsubishi Electric Visual Solutions America Inc 9351 Jeronimo Road Irvine CA 92618 U S A Telephone number 1 949 465 6000 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Trademark Registered trademark Macintosh is registered trademark of Apple Computer Inc DLP Digital Micromirror Device DMD and BrilliantColor are all trademarks of Texas Instruments HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC Microsoft Windows Windows XP Windows Vista and Internet Explorer are registered trademarks trademarks or trade names of Microsoft Corpo ration in the U S and or other countries Other brand or product names are trademarks or registered trademarks of their respective holders EN 4 Important safe
91. tments 9 Press MENU EXIT to exit and save the settings Saturation is the amount of that color in a video picture Lower settings produce less saturated colors a setting of 0 removes that color from the image entirely If the saturation is too high that color will be overpowering and unrealistic Using Wall Screen EN 30 In the situation where you are projecting onto a colored surface such as a painted wall which may not be white the Wall Screen feature can help correct the projected picture s color to prevent possible color difference between the source and projected pictures To use this function go to the DISPLAY gt Wall Screen menu and press lt gt to select a color which is the closest to the color of the projection surface There are several recalibrated colors to choose from Light Yellow Pink Light Green Blue and Blackboard Setting the presentation timer The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations Follow these steps to utilize this function 1 Press TIMER SET UP on the remote control or go to the SYSTEM SETUP Basic gt Presentation Timer menu and press MODE ENTER to display the Presentation Timer page 2 Press W to highlight Timer period and decide the timer period by pressing lt p gt The length of time can be set from 1 to 5 minutes in 1 minute increments and 5 to 240 minutes in 5 minute increments
92. to the SYSTEM SETUP Advanced gt Security Settings menu Press MODE ENTER The Security Settings page is displayed 2 Highlight Power on lock and select On by pressing lt gt 3 As pictured to the right the four arrow keys A gt V lt respectively represent 4 digits 1 2 3 4 According to the password you desire to set press the arrow keys to enter six digits for the password 4 Confirm the new password by re entering the new password Once the password is set the OSD menu returns to the Security Settings page Cz The digits being input will be displayed as asterisks on screen Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it Password Keep this number in a safe place 5 To leave the OSD menu press MENU EXIT If you forget the password If the password function is activated you will be asked to enter the six digit password every time you turn on the projector If you enter the wrong password the password error message as pictured to the right is displayed lasting for three Password Error seconds and the message INPUT PASSWORD follows You can retry by Please Try again entering another six digit password or if you did not record the password in this manual and you absolutely do not remember it you can use the password recall procedure See Entering the password recall procedure
93. tric Asia Pte Ltd http www mitsubishielectric com sg 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Sales Inquiries Phone 65 6473 2308 Fax 65 6475 9503 E mail _ Peripherals asia meap com Technical Inquiries Phone 65 6470 2666 Fax 65 6475 9503 INDIA Mitsubishi Electric Asia Pte Ltd 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Sales Inquiries Phone 65 6473 2308 Fax 65 6475 9503 E mail Peripherals asia meap com Technical Inquiries Phone 65 6470 2666 Fax 65 6475 9503 INDONESIA Mitsubishi Electric Asia Pte Ltd 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Sales Inquiries Phone 65 6473 2308 Fax 65 6475 9503 E mail Peripherals asia meap com Technical Inquiries Phone 65 6470 2666 Fax 65 6475 9503 PHILIPPINES Mitsubishi Electric Asia Pte Ltd http www mitsubishielectric com sg 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Sales Inquiries Phone 65 6473 2308 Fax 65 6475 9503 E mail Peripherals asia meap com Technical Inquiries Phone 65 6470 2666 Fax 65 6475 9503 VIETNAM Mitsubishi Electric Asia Pte Ltd 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Sales Inquiries Phone 65 6473 2308 Fax 65 6475 9503 E mail Peripherals asia meap com Technical Inquiries Phone 65 6470 2666 Fax 65 64
94. ult your dealer about the range e Retract the adjuster feet e Remove the battery from the remote control e Pack the projector in its original packing or equivalent Transporting the projector It is recommended that you ship the projector with its original packing or equivalent EN 47 Lamp information Getting to know the lamp hour When the projector is in operation the duration in hours of lamp usage is automatically calculated by the built in timer The method of calculating the equivalent lamp hour is as follows Total equivalent lamp hour hours used in Low mode 10 7 hours used in Standard mode Cz See Setting Lamp mode as Low below for more information on Low mode The lamp hour in Low mode is calculated as 7 10 of that in Standard mode That is using the projector in Low mode helps to extend the lamp hour by 3 7 To obtain the lamp hour information 1 Press MENU EXIT and then press lt gt until the SYSTEM SETUP Advanced menu is highlighted 2 Press W to highlight Lamp Settings and press MODE ENTER The Lamp Settings page is displayed 3 You will see the Equivalent lamp hour information appearing on the menu 4 To leave the menu press MENU EXIT You can also get the lamp hour information on the INFORMATION menu Extending lamp life The projection lamp is a consumable item that normally can last up to 3500 used in Standard mode 5000 used in Low mode hours with proper usage Such
95. ur projector Do not operate if smoke strange noise or odor comes out of your pro jector It may cause fire or electric shock In this case unplug immedi ately and contact your dealer Never remove the cabinet This projector contains high voltage circuitry An inadvertent contact may result in an electric shock Except as specifically explained in User Manual do not attempt to service this product by yourself Please con tact your dealer when you want to fix adjust or inspect the projector Do not modify the projector t can lead to fire or electric shock Do not keep using the damaged projector f the projector is dropped and the cabinet is damaged unplug the pro jector and contact your dealer for inspection It may lead to fire if you keep using the damaged projector Do not face the projection lens to the sun tcan lead to fire Use correct voltage f you use incorrect voltage it can lead to fire Do not place the projector on uneven surface Place the projector on a level and stable surface only Do not look into the lens when the projector is operating It may hurt your eyes Never let children look into the lens when the projector is on Do not unplug the power cord during operation It can lead to lamp breakage fire electric shock or other trouble Wait for the fan to stop before unplugging the power cord Do not touch the air outlet grilles and bottom plate Do not touch them or put other equipment close to t
96. use an HDMI cable when making connection between the projector and HDMI devices To connect the projector to an HDMI device 1 2 Take an HDMI cable and connect one end to the HDMI output port of the video device Connect the other end of the cable to the HDMI input port on the projector AV device HDMI cable option CF In the unlikely event that you connect the projector to a DVD player via the projector s HDMI input and the projected picture displays wrong colors please change the color space to YUV See Changing Color Space on page 24 for details When you connect this projector and a Digital device such as a DVD player via the HDMI terminal black color may appear dark and deep depending on the type of the connected device This depends on the black level setting of the connected device There are two kinds of methods to digitally transfer image data in which different black level settings are employed respectively Therefore the specifications of the signals output from DVD players differ depending on the type of the digital data transfer method they use Some DVD players are provided with a function to switch the methods to output digital signals When your DVD player is provided with such function set it as follows EXPAND or ENHANCED gt NORMAL See the users guide of your DVD player for details When you switch to HDMI input the projected picture may di
97. uster foot Kensington Lock This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector Please contact Kensington Technology Group below Kensington Technology Group 2855 Campus Drive San Mateo CA 94403 U S A Phone 1 650 572 2700 Fax 1 650 572 9675 EN 7 Controls and functions Projector 1 Focus ring Adjusts the focus of the projected image See Fine tuning the image size and clarity on page 25 for details 2 POWER indicator light Lights up or flashes when the projector is under operation See Indicators on page 53 for details 3 SOURCE POWER TEMP all Displays the source selection bar See Switching input signal on page 24 for details 0 7 4 lt 4 Left BLANK Used to hide the screen picture See Hiding the image Yu a on page 32 for details 5 MODE ENTER Selects an available picture setup mode See Selecting a picture mode on page 28 for details Enacts the selected On Screen Display OSD menu item 6 MENU EXIT Turns on the On Screen Display OSD menu Goes back to previous OSD menu exits and saves menu settings See Using the menus on page 22 for details 7 TEMPerature indicator light Lights up red if the projector s temperature becomes too high See Indicators on page 53 for details

Download Pdf Manuals

Related Search

Related Contents

G Instruction manual and warnings I Manuale di “Istruzioni” ed  Easy Tap - Event Dispense  ダウンロード - Wacom  ・賞例4=漏水・  Anleitung HD-Digitalreceiver Arion  Guided Start-up Using Hospira MedNet Software    Depuis votre tablette ou smartphone détectez et localisez les fuites  

Copyright © All rights reserved. Failed to retrieve file