Chief PAC253
Contents
1. MEASUREMENTS MILLIMETERS INCHES Installation Instructions PAC253 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional O2. Rev00 2009 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 07 09 USA International Europe Asia Pacific 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA RY rb D FT BGR ab E s A IE DPR 24F P 86 755 8996 9226 486 755 8996 9217 K2 7 D is SRCONSUNERS gt
3. 4 INSTALLATION Installing CPU Holder with CPU to Mount WARNING Exceeding the weight capacity can result in Mounting Button serious personal injury or damage to equipment It is the On interface bracket or display installer s responsibility to make sure the combined weight of all components located between the CPU Accessory and the display does not exceed the weight limits for the specific wall mount being used The CPU Accessory weighs 17 lbs 7 7 kg which needs to be included in this combined weight total KI Ve Figure 5 4 Ensure mounting buttons are fully seated in teardrop slots Install the CPU holder with CPU onto mount and route wires 5 Close locking flag and cables following the instructions provided with the mount 6 Connect cables to display Cable ties E are provided for cable management WARNING IMPROPER INSTALLATION CAN LEAD TO CPU HOLDER FALLING Make certain mounting buttons on CPU holder are fully engaged in teardrop holes in mount and latching flag on mount is fully closed before installing the display Installing Display WARNING DISPLAY MAY WEIGH IN EXCESS OF 40 LBS ALWAYS use two people when lifting and follow proper lifting techniques when installing Installation Instructions PAC253 PAC253 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8832 002017
4. INSTALLATION INSTRUCTIONS CPU Holder S CHIEF PAC253 Our Mounts Your PAC253 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty Itis the installer s responsib
5. ility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the CPU Accessory and the display does not exceed the weight limits for the specific wall mount being used The CPU Accessory weighs 17 lbs 7 7 kg which needs to be included in this combined weight total La 16 21 16 0010 gt SHOWN IN TAXIR ES 4x14 DES E MAX WIDTH PATIERN IS 3 28 4 1 81 DEPTH LOCKING FLAG CPU HOLDER SHOWN ON 14 X1 4 PATTERN i SJ 8 8 12 062 14000 7 874 la 7 000 I CPU HOLDER FACEPLATE 20 000 20 14 RECOMMENDED HEIGHT OF CPU
6. ptional Opcional Opzionale Optie En option ka y E 9 3 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit PAC253 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1 8 included 1 4 A 1 CPU Holder 1 Locking Flag e E 4 Mounting Button Cable Tie Es K 6 10 24 x 1 2 ia 10 24 x 3 8 B 1 Faceplate F 6 Hook and Loop G 1 1 8 1 194x 375x 032 L 1 0 2 ST Installation Instructions PAC253 ASSEMBLY Assembling CPU Accessory Attaching Locking Flag 1 Attach locking flag C to faceplate B using one 10 24 x 1 2 Phillips undercut machine screw H one spacer M and one 10 24 Nylock lock nut L See Figure 1 NOTE The locking flag may be installed in one of two locations dependent upon the display mounting pattern See Figure 1 Locking flag may be installed in either location noted QU EM Q CS Figure 1 Attaching Mounting Buttons 1 A
7. ttach four mounting buttons D to CPU holder A using four 10 24 x 1 2 flat head cap screws J See Figure 2 Figure 2 Placing CPU in CPU Holder 1 Puthook and loop tabs F together so there are 3 squares of hook and loop 2 Remove paper from one side of each of the three hook and loop squares 3 Attach hook and loop squares to the CPU See Figure 3 CPU d e F x3 Figure 3 4 Remove paper from hook and loop squares and press the CPU against the CPU holder A PAC253 Installation Instructions Attaching Faceplate to CPU Box IMPORTANT The following procedure assumes that 1 Attach faceplate B to GPU box A using six 10 24 x 3 8 proper interface bracket for display being mounted button head cap screws K See Figure 4 has already been installed on display If no interface bracket is present on display install bracket to display using instructions included with interface bracket before proceeding To install the display 1 Ensure that locking flag is in open position See Figure 5 2 While supporting each side of display align four mounting buttons on display or interface bracket with four teardrop slots in CPU holder See Figure 5 3 Lower display firmly into place See Figure 5 Figure
Download Pdf Manuals
Related Search