Miele CS 1012 G hob
Contents
1. 44 Installing removing the appliance Installing the appliance m Feed the connection cable down through the cut out m Starting at the front position the appliance in the worktop cut out m Using both hands press down evenly on the sides of the appliance until it clicks into position When doing this make sure that the seal under the appliance sits flush with the worktop on all sides This is important to ensure an effective seal all round Do not use sealant m Push the appliance to the side until the holes in the spacer bar can be seen m Fit the cover strip into the holes in the spacer bar m Starting at the front position the next appliance in the worktop cut out m Connect the appliance s to the mains see Electrical connection and to the gas supply see Gas connection m Check that the appliance s work s Removing the appliance If the appliance is accessible underneath it can be pushed up out of the cut out from below It must be pushed up from the back first If the appliance is not accessible underneath take hold of the appliance with both hands at the back pull it forwards then lift it up and out 45 General installation tips Seal between the appliance and the Tiled worktop worktop Grout lines and the hatched area underneath the surface of the appliance must be smooth and even If they are not the appliance will not sit The2. 2 Front 3 Casing depth Casing depth including the mains connection box with mains connection cable L 1440 mm 8 Casing depth including the gas connection R 1 2 ISO 7 1 DIN EN 10226 38 Appliance and building in dimensions CS 1034 1 Spring clamps 2 Front 3 Casing depth Casing depth including the mains connection box with mains connection cable L 1440 mm 8 Casing depth including the gas connection R 1 2 ISO 7 1 DIN EN 10226 39 Preparing the worktop m Make the worktop cut out for one or more appliances in accordance with the building in diagrams Remember to maintain the minimum safety distance from the back wall as well as from any tall unit or side wall to the right or left of the hob See Safety instructions for installation m Seal the cut surfaces with a suitable heat resistant sealant to avoid swelling caused by moisture If during installation you find that the seals on the corners of the frame are not flush with the worktop surface the corner radius lt R4 can be carefully scribed to fit 40 Installation of several appliances When installing two or more appliances next to each other a spacer bar 2 must be used between each one See Fixing the spring clamps and spacer bars Worktop cut out Worktop cut out two appliances three appliances To calculate the cut out width D required Add up the widths of each appliance e g 288 m
3. Conversion to another type of gas is described under Conversion to another type of gas For any gas work in the UK always use a Gas Safe registered engineer REGISTER 49 Gas connection Connection The gas connection must be installed so that connection can be made either from inside or outside the kitchen unit and the isolating valve must be easily accessible and visible by opening one of the kitchen doors if necessary After installing the appliance the gas burners have to be set for local conditions When the gas hob has been installed it is essential to check that neither the gas pipe not the electricity cable is in contact with hot parts of the appliance or hot gas exhaust otherwise heat damage to the pipe and cable could occur A test for possible leakages must be carried out after installation Safety regulations demand that a pressure test point is installed near a gas hob to allow an engineer to test the pressure following servicing The appliance is supplied with an R 1 2 ISO 7 1 DIN EN 10226 gas connection point An appropriate rigid connection and isolating valve must be installed for final connection The gas connection must be so sited that it is not adversely heated when the appliance is in operation 50 Connection with test point specifically for GB 2 Connection with test point specifically for GB and 90 angle Conversion to another type of gas
4. N Connection to the gas supply or conversion from one type of gas to another should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations e g Gas Safe registered in the UK When converting to a different type of gas the main jets and the small jets have to be changed CS 1012 1 Nominal rating at high setting Gas type kW Medium Natural gas H 1 80 burner Liquid gas 1 80 131 g h Large Natural gas H 3 00 burner Liquid gas 3 00 218 g h Total output Natural gas H 4 80 Liquid gas 4 80 349 g h Nominal rating at low setting Gas type kW Medium Natural gas H 0 35 burner Liquid gas 0 35 Large Natural gas H 0 50 burner Liquid gas 0 50 Screw in the new jets according to the following table Jet table For UK and IE Main jet Small jet Natural gas H Medium burner 1 00 0 42 Large burner 1 28 0 52 Liquid gas Medium burner 0 67 0 27 Large burner 0 87 0 32 The jet markings refer to 1 100 mm of the jet diameter 51 Conversion to another type of gas CS 1034 1 Nominal rating at high setting Gas type kW Small burner atural gas H 1 00 Liquid gas 1 00 73 g h Medium atural gas H 1 80 burner Liquid gas 1 80 131 g h Large burner atural gas H 3 00 Liquid gas 3 00 218 g h Total output atural gas H 8 80 Li
5. do not let children play with the appliance or its controls Children under 8 years of age must be kept away from the hob unless they are constantly supervised Children 8 years and older may use the hob only if they have been shown how to use it in a safe way and understand the hazards involved P The hob gets hot when in use and remains hot for quite a while after being switched off Keep children well away from the appliance until it has cooled down and there is no danger of burning Do not store anything which might arouse a child s interest in storage areas above or next to the hob Otherwise they could be tempted into climbing onto the appliance with the risk of burning themselves P Keep all pans out of reach of children Turn pan handles inwards away from the edge of the hob Danger of burning or scalding Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Dispose of or recycle all packaging safely as soon as possible Warning and Safety instructions Technical safety Before installation check the hob for visible signs of damage Do not install and use a damaged appliance It could be dangerous P The electrical safety of the hob can only be guaranteed if correctly earthed It is most important that this basic safety requirement is observed and regularly tested and where there is any doubt the hous
6. appliance must not be sealed flush with the worktop and the sealing The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop strip underneath the top part of the appliance will not provide a good seal between the appliance and the worktop with sealant e g silicone This could result in damage to the appliance or the worktop if it ever needs to be removed for servicing 46 Electrical connection All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations BS 7671 in the UK If the connection cable is damaged it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V F pvc insulated available from Miele Installation repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Ensure power is not supplied to the appliance until after installation or repair work has been carried out The appliance must only be operated when built in This is to ensure that all electrical parts are shielded Live parts must not be exposed Connection should be made via a fused plug and switched socket or a double pole fused spur connection unit or a suitable isolator as appropriate which complies with national and local safety regulations and the on off
7. competent person in strict accordance with current national and local safety regulations Hepairs and other work by unqualified persons could be dangerous Miele cannot be held liable for unauthorised work Warning and Safety instructions During installation maintenance and repair work the hob must be disconnected from the gas supply and mains electricity supply While the hob is under guarantee repairs should only be undertaken by a service technician authorised by Miele Otherwise the guarantee is invalidated P Faulty components must only be replaced by genuine Miele original spare parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used P If the connection cable is damaged it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V F pvc insulated available from Miele P The hob is not intended for use with an external timer switch or a remote control system P Do not connect the hob to the mains electricity supply by a multi socket adapter or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating Do not use the hob if it is faulty Switch it off immedi ately and disconnect it from the mains electricity supply and the gas supply Call the Service Department Warning and Safety instructions gt In areas which may be subject to infestation by cockro
8. du pays ou sera install l appareil This appliance can be used in countries other than those specified on the appliance It is however set up for connection to the gas and electricity supplies in the countries specified For use in other countries please contact the Miele spare parts or customer service department in your country CID L apparecchio pu essere usato anche in paesi diversi da quello indicato sull apparecchio stesso Tuttavia le varianti specifiche di un determinato paese e il tipo di allacciamento alla rete hanno un importanza fondamentale per il suo sicuro e corretto funzionamento Per questo se si vuole usare l apparecchio in un paese diverso rivolgersi al servizio di assistenza tecnica Miele del paese in cui si intende usarlo ND Het apparaat is ook toegelaten voor gebruik in andere landen dan de landen die op het apparaat vermeld staan De specifieke uitvoering en de aansluitwijze zijn van groot belang voor het goed en veilig functioneren Neem daarom contact op met de Technische Dienst van de fabrikant in uw land als u het apparaat in een land wilt gebruiken dat niet op het apparaat vermeld staat Contents Guide to the appliance 6 ES OT PPM 6 CS 108441 EE Y Warning and Safety instructions 9 Caring for the environment 0 000000 i esee 20 Before using for the first me 21 Operation 232 eye yet esse 22 Rapid ignition system 22 Switching on adjusting the flame and switching of
9. the burner do not spread out beyond the base and up the sides of the pan gt Unless the pan manufacturer states that you can do SO do not use pans with very thin bases on the hob and never heat up empty pans as they could get damaged This could also damage the appliance P The pan support supplied must always be used Pans must not be placed directly on the burner gt Do not store any inflammable objects near the hob gt Remove splashes of fat and other food debris from the surface as soon as possible These are a fire hazard gt Replace the pan supports carefully to avoid scratching the surface of the hob Warning and Safety instructions gt Using the hob will cause a build up of heat and moisture in the room in which it is installed Ensure that the room has sufficient natural or mechanical means of ventilation e g an extractor P If the hob is used for very long periods of time additional ventilation of the room may be necessary e g by opening windows or doors or running the extractor on the highest setting When using an electrical appliance e g a hand held food blender near the hob ensure that the cable of the electrical appliance does not come into contact with the hot hob The insulation on the cable could become damaged giving rise to an electric shock hazard P Spray canisters aerosols and other inflammable substances must not be stored in a drawer under the hob Cutlery inserts must b
10. Miele Operating and installation instructions Gas hobs CS 1012 1 CS 1034 1 To avoid the risk of accidents or en GB damage to the appliance it is essential to read these instructions before it is installed and used for the first time M Nr 09 094 640 CDD Das Ger t ist auch f r den Gebrauch in anderen als auf dem Ger t angegebenen Bestimmungsl nder zugelassen Die landesspezifische Ausf hrung und die Anschlussart des Ger tes haben wesentlichen Einfluss auf den einwandfreien und sicheren Betrieb F r den Betrieb in einem anderen als auf dem Ger t angegebenen Bestimmungsland wenden Sie sich bitte an den f r das Land zust ndigen Kundendienst CED El aparato est autorizado para el uso en paises diferentes a los paises de destino indicados La ejecuci n especifica para cada pais y el tipo de conexi n del aparato influyen de forma decisiva en el funcionamiento correcto y seguro Para el funcionamiento en un pais diferente al pais de destino indicado en el aparato consulte al Servicio Post venta autorizado para el pais CF Cet appareil est galement homologu dans des pays diff rents de ceux mentionn s sur l appareil Pour que l appareil fonctionne parfaitement et en toute s curit il est important de disposer de l ex cution sp cifique au pays et du type de raccordement appropri Pour le fonctionnement dans un pays autre que celui sp cifi sur l appareil veuillez vous adresser au service apres vente
11. Tel 01 461 07 10 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Il Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa iele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 4111 ce M Nr 09 094 640 01
12. aches or other vermin pay particular attention to keeping the appliance and its surroundings clean at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Correct use P The hob gets hot when in use and remains hot for quite a while after being switched off Do not touch it whilst it could still be hot P If a cooker hood is installed above the hob ensure that the burners are always covered with a pan when in use Otherwise flames could reach the cooker hood parts of which could then be damaged or set on fire gt Do not leave the hob unattended whilst it is being used Oil and fat are potential fire hazards as they can ignite if overheated If oil or fat does catch fire do not attempt to put out the flames with water Use a suitable fire blanket saucepan lid damp towel or similar to smother the flames gt Do not use the hob to heat up the room Due to the high temperatures radiated objects near the appliance could catch fire The life of the appliance could also be reduced Warning and Safety instructions P Use heat resistant pot holders or gloves when using the hob Ensure that they do not come into contact with the flames Do not use large cloths tea towels or similar as the ends could touch the flames and catch fire Do not let the gloves get damp or wet as this causes heat to transfer through the material more quickly with the risk of scalding or bu
13. ate a fault If the burner does not ignite turn the control to off e Air the room or wait at least 1 minute before trying again If the burner does not ignite the second time turn the control to e and see Problem solving guide When switching on re ignition sometimes occurs 1 2 clicks if the flame on the ignition safety device has gone out briefly or if the thermal element is not hot enough e g following a gust of air Regulating the flame The burners can be regulated at any level between the strongest and weakest flame Control the flame so that it does not spread out beyond the sides of the pan As the outer part of the flame is much hotter than the centre the tips of the flames should stay beneath the pan base Flame tips which extend beyond the sides of the pan merely warm up the air in the room and can also damage pan handles and increase the danger of injury m Turn the control clockwise to position Switching off This stops the flow of gas and the flame goes out 23 Operation In operation indicator and Residual heat indicator When a gas burner is switched on the relevant in operation indicator lights up Once ithas reached a certain temperature the residual heat indicator also lights up The in operation indicator goes out when the gas burner is switched off The residual heat indicator remains on until the gas burner is cool enough to touch Do not touch or place a
14. d building regulations To avoid the risk of damaging the hob fit the wall units and extractor hood before installing it P The room in which the gas hob is installed must be at least 20 m in size with a door or window in it which can be opened to the outside air gt The veneer or laminate coatings of worktops or adjacent kitchen units must be treated with 100 C heat resistant adhesive which will not dissolve or distort Any backmoulds must be of heat resistant material P This appliance must not be used in a non stationary location e g on a ship P An electric fryer must not be installed directly next to a gas hob as the gas flames could ignite the fat in the fryer It is essential to maintain a distance of at least 288 mm between these two appliances P A gas hob must not be installed above a fridge fridge freezer freezer dishwasher washing machine or tumble dryer gt The hob may only be installed above a Miele oven if the worktop is at least 40 mm thick 34 P Ensure that the gas pipe and electrical cable are installed in such a way that they do not touch any parts of the appliance which become hot This could cause damage P The electrical cable and any flexible gas connection pipe must be installed in such a way so that they do not come into contact with any moving kitchen parts e g a drawer and cannot become trapped P Observe carefully the safety distances given on t
15. e heat resistant gt Always ensure that food is sufficiently cooked or reheated Some foods may contain micro organisms which are only destroyed by thorough cooking at a sufficiently high temperature for long enough Therefore when cooking or reheating food such as poultry it is particularly important that the food is completely cooked through If in doubt select a longer cooking or reheating time Warning and Safety instructions P Avoid allowing liquids or foods containing salt to spill onto the hob If salty foods or liquids do get on the hob they should be removed as soon as possible to avoid the risk of corrosion P If the hob is installed behind a kitchen furniture door it may only be used with the furniture door open Only close the door when the appliance is switched off and the residual heat indicators have gone out If the hob has not been used for a long period of time it should be thoroughly cleaned before it is used again It is also advisable to have the appliance tested for safety Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out ofthe reach of babies a
16. eam could reach electrical components and cause a short circuit The appliance should be cleaned after each use Let it cool down to room temperature before cleaning To avoid water marks and limescale deposits use a soft cloth to dry surfaces that have been cleaned with water Cooked food which spills over onto the hot appliance can cause discolouration of the burner components and the stainless steel surface Remove any soiling immediately 28 To avoid damaging the surface or your hob do not use cleaning agents containing soda alkalines ammonia acids or chlorides cleaning agents containing descaling agents stain or rust removers abrasive cleaning agents e g powder cleaners and cream cleaners solvent based cleaning agents dishwasher cleaner grill and oven cleaners glass cleaning agents hard abrasive brushes or sponges e g pot scourers brushes or sponges which have been previously used with abrasive cleaning agents sharp pointed objects these can damage the seal between the frame and the worktop melamine eraser blocks Cleaning and care Stainless steel surfaces Clean stainless steel surfaces using an E Cloth or with a solution of warm water and a little washing up liquid applied with a soft sponge In the case of stubborn dried on soiling soak first Finally dry with a soft cloth If necessary the pad on the back of a washing up
17. ed Pans must not be placed directly on the burner Place pans securely on the pan rest to minimise the risk of tipping Do not use pots or pans with legs e g dutch ovens 25 Energy saving tips Use a pan lid whenever possible to minimise heat loss Cook with as little water as possible Cooking times are greatly reduced when using a pressure cooker Turn the flame down promptly to a lower setting when the pan has come to the boil Wide shallow pans are preferable to tall narrow ones They will heat up faster 26 Safety features Thermo electric ignition This appliance has a thermo electric ignition safety device If the flame goes out for example if food has boiled over or if there is a sudden draught and automatic re ignition has been unsuccessful the supply of gas to the burner will be cut off m To use the burner again turn the control clockwise to the e position and then switch it back on as normal Safety cut out If a burner has been used for an unusually long period approx 4 hours it will switch off automatically To use the burner again turn the control clockwise to the e position and then switch it back on as normal 27 Cleaning and care Miele offer arange of branded cleaning and conditioning agents for your hob See Optional accessories NDo not use a steam cleaning appliance to clean this appliance The st
18. ehold wiring system should be inspected by a qualified electrician Miele cannot be held liable for the consequences of an inadequate earthing system e g electric shock Before connecting the hob to the mains electricity supply make sure that the data quoted on the data plate match the household mains supply otherwise the appliance could be damaged Consult a qualified electrician if in any doubt P For safety reasons the hob may only be used after it has been built in gt Do not open the casing of the hob Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults Warning and Safety instructions gt Connection to the gas supply must be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations e g a Gas Safe registered technician in the U K The hob may be connected via a fused plug and switched socket If you wish to connect it to a fused spur connection or of if the appliance is supplied without a plug it must be installed and connected to the electrical supply by a suitably qualified and competent person is strict accordance with current local and national safety regulations Miele cannot be held liable for damage caused by incorrect installation or connection Installation maintenance and repairs may only be carried out by a suitably qualified and
19. equirements Improper use can however present a risk of both personal injury and material damage To avoid the risk of accidents and damage to the appliance please read these instructions carefully before installation and before using it for the first time They contain important notes on installation safety use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Warning and Safety instructions Correct application P This hob is not designed for commercial use It is intended for use in domestic households and in similar working and residential environments such as Shops Offices and showrooms and by residents in establishments such as Hostels and guest houses P The hob is intended for domestic use only to cook food and keep it warm Any other use is not supported by the manufacturer and could be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation P The hob is not intended for outdoor use P The hob can only be used by people with reduced physical sensory or mental capabilities or lack of experience and knowledge if they are supervised whilst using it or have been shown how to use it in a safe way and understand the hazards involved Warning and Safety instructions Safety with children P The hob is not a toy To prevent the risk of injury
20. essfully the in operation and residual heat indicators are flashing at the same time There has been a power cut Re ignition was not possible The gas supply has been interrupted Turn all the controls clockwise to the e position You can then operate the appliance as normal If the problem persists disconnect the appliance from the electricity supply for a few seconds there has been a power cut Turn all the controls clockwise to the e position You can then operate the appliance as normal If the problem persists disconnect the appliance from the electricity supply for a few seconds the burner does not ignite after several attempts Disconnect the appliance from the electricity supply for a few seconds If the problem persists check whether the burner is assembled correctly the gas supply tap is turned on the burner is dry and clean the flame slits are dry and unblocked the gas flame goes out after being lit The flames need to touch the ignition safety device so that it heats up sufficiently If the flames do not touch the ignition safety device check that the burner components are assembled correctly there is no soiling on the ignition safety device If there is remove it carefully see Cleaning and care 31 Problem solving guide the gas flame suddenly looks different Check whether the burner component
21. he following pages All dimensions in this instruction booklet are given in mm Safety instructions for installation Safety distance above the appliance A minimum safety distance must be maintained between the appliance and the cooker hood above it See the cooker hood manufacturer s operating and installation instructions for details If the manufacturer s instructions are not available for the cooker hood a minimum safety distance of at least 760 mm must be maintained For any flammable objects e g utensil rails wall units etc a minimum distance of at least 760 mm must be maintained between them and the appliance below When two or more appliances are installed together below a cooker hood e g an electric hob and a gas wok combiset which have different safety distances given in their installation instructions you should select the greater distance of the two 35 Safety instructions for installation Safety distances to the sides of the hob Ideally the hob should be installed with plenty of space on either side There may be a wall at the rear and a tall unit or wall at one side On the other side however no unit or divider should stand higher than the hob see illustrations Due to the high temperatures radiated by the appliance it is essential that a minimum distance of 50 mm is maintained between the worktop cut out and the back wall The following minimum distance between the workto
22. m 380 mm and subtract 16 mm from this figure Number of Appliance width in mm Worktop cut out in mm appliances 1 288 288 16 272 2 288 288 288 288 16 560 2 288 380 288 380 16 652 3 288 288 288 288 288 288 16 848 3 288 288 380 288 288 380 16 940 41 Installation of several appliances Spring clamps Spacer bars Gaps between spacer bars and worktop 4 Cover strips The illustration shows a worktop cut out with spring clamps and spacer bars 2 for 3 appliances An additional spacer bar is required for each additional appliance The position for securing each additional spacer bar will depend on the width of appliance B 288 mm 380 mm 576 mm 42 Fixing the spring clamps and spacer bars Wooden worktops m Position the spring clamps supplied CD and spacer bars 2 on the top edge of the cut out in the positions marked m Secure the spring clamps and spacer bars with the 3 5 x 25 mm screws supplied 43 Fixing the spring clamps and spacer bars Granite and marble worktops The screws are not required for granite or marble worktops m Apply silcone to the side edges and the lower edges of spring clamps and spacer bars m Then fill gap between the spacer m Position and secure the spring bars and the worktop with silicone clamps and spacer bars using strong double sided adhesive tape
23. nd young children Danger of suffocation 20 Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the After sales service data plate guarantee section of this booklet Cleaning for the first time m Remove any protective foil and stickers m Clean all removable parts of the burners with a solution of warm water and a little washing up liquid applied with a soft sponge Dry all parts thoroughly after cleaning and then reassemble the burners see Cleaning and care m Clean the stainless steel trough with a damp cloth and then wipe dry Metal components have a protective coating which may give off a slight smell when heated up for the first time The smell and any vapours will dissipate after a short time and do not indicate a faulty connection or appliance 21 Opera
24. ny heat sensitive objects on the gas hob while the residual heat indicator is still on Danger of burning and fire If the displays are flashing this shows there is a fault See section Problem solving guide 24 Suitable pans Burner Min pan base diameter in cm Small burner 10 Medium burner 12 Large burner 14 Max diameter at top of pan in cm Small burner 20 Medium burner 22 Large burner 24 Refer to the chart above and ensure that the pan diameter falls within the minimum and maximum diameters given for the burner you are using A pan which is too small will be unstable on the pan support If the pan base diameter is too large flames can spread out to the sides and damage or burn the worktop wall claddings or surrounding units and also parts of the hob The manufacturer cannot be held liable for this type of damage Remember when purchasing new pans that manufacturers usually refer to the diameter at the top of the pan in their documentation Any heat resistant pans can be used Pans with thick bases are preferable as these distribute heat more evenly With thin bases there is a danger of food overheating in places Stir the food frequently Select pans which are suitable for the burner they are to be used on In general use larger diameter pans on the large burners and smaller diameter pans on the small burners Always place pans on the pan support suppli
25. p cut out and a wall or tall unit to the right or left of it must be maintained 40mm for CS 1212 CS 1212 1 CS 1221 CS 1221 1 CS 1222 CS 1223 CS 1234 CS 1234 1 50mm for CS 1112 CS 1122 CS 1134 CS 1326 CS 1327 CS 1411 100 mm for CS 1012 CS 1012 1 150mm for CS 1421 CS 1312 CS 1322 200 mm for CS 1034 CS 1034 1 250mm for CS 1011 CS 1021 Not allowed 36 Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut out and any niche cladding to protect it from heat damage If the niche cladding is made from a combustible material e g wood a minimum safety distance of 50 mm must be maintained between the cut out and the cladding If the niche cladding is made from a non combustible material e g metal natural stone ceramic tiles a minimum safety distance of 50 mm less the thickness of the cladding must be maintained between the cut out and the cladding Example 15 mm niche cladding 50 mm 15 mm minimum safety distance of 35 mm 0 Masonry 2 Niche cladding Dimension x thickness of niche cladding material 3 Worktop Worktop cut out Minimum safety distance for combustible materials is 50 mm for non combustible materials is 50 mm less dimension x 37 Appliance and building in dimensions CS 1012 1 Spring clamps
26. quid gas 8 80 640 g h Nominal rating at low setting Gas type kW Small burner Natural gas H 0 25 Liquid gas 0 25 Medium burner Natural gas H 0 35 Liquid gas 0 35 Large burner Natural gas H 0 50 Liquid gas 0 50 52 Screw in the new jets according to the following table Jet table For UK and IE Main jet Small jet Natural gas H Small burner 0 76 0 39 Medium burner 1 00 0 42 Large burner 1 28 0 52 Liquid gas Small burner 0 50 0 23 Medium burner 0 67 0 27 Large burner 0 87 0 32 The jet markings refer to 1 100 mm of the jet diameter Conversion to another type of gas Changing the jets Disconnect the gas hob from the mains electricity supply Turn off the gas supply To change the main jets m Carefully remove the upper section of the appliance When doing this make sure you do not also pull out the light unit for the display located underneath the upper section To release the unit squeeze together the two clamps B m Remove the pan support burner cap and burner head m Using an M7 socket spanner unscrew main jet 49 m Change the main jet m Using a small screwdriver unscrew To change the small jets small jet in the gas fitting The upper section of the appliance has m Pull out the jet with a pair of pliers to be removed before the small jets can be changed m Fit the correct jets securely see je
27. r and ignition safety device should be very carefully wiped clean using a well wrung out cloth Do not let the ignitor get wet If it gets wet it will not spark After cleaning dry all surfaces with a clean cloth Make sure that the flame slits are clean and completely dry The surface of the burner cap will become more matt with time This is quite normal and will not affect the operation of the hob 30 Reassemble the burner After cleaning the burner it must be reassembled in the correct order m Place the burner head 48 on to the burner base 48 so that the ignition safety device 9 and the ignitor 4 extend through their respective holes in the burner head The burner head must click into place correctly m Place burner cap 44 flat over burner head When correctly positioned it will not slide about Problem solving guide N Repairs to the gas and electrical components of this appliance must only be carried out by a suitably qualified and competent person to ensure safety Gas Safe registered in the UK Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work What to do if the burner does not ignite when the hob is being used for the first time or after a long period of not being used There could be an air lock in the gas pipe You may need to make several attempts before the burner ignites succ
28. rning yourself Do not flamb under a cooker hood The flames could set the cooker hood on fire gt Do not use the hob as a resting place for anything When the appliance is switched on either deliberately or by mistake or when there is residual heat present the article could melt or catch fire gt Where several appliances are installed side by side Do not place hot pots or pans on the cover strip as this can damage the seal Do not cover the hob e g with a hob cover a cloth or protective foil The material could catch fire shatter or melt if the appliance is switched on by mistake or if it is still warm gt Do not use plastic or aluminium foil containers These melt at high temperatures and could catch fire Do not heat up unopened tins of food on the hob as pressure will build up in the tin causing it to explode This could result in injury and scalding or damage 16 Warning and Safety instructions gt Make sure all the components of the gas burners have been correctly assembled before switching on P Pans must be the correct size for the burner they are used on see Suitable pans A pan which is too small will be unstable on the pan support If the pan diameter is too large flames can spread out to the sides and damage or burn the worktop wall claddings or Surrounding units and also parts of the hob Miele cannot be held liable for this type of damage Ensure that the flames from
29. s are assembled correctly the gas flame goes out during operation Check whether the burner components are assembled correctly the ignitor on the burner does not spark Check whether the mains fuse has tripped If it has contact a qualified electrician or the Miele Service Department food deposits have lodged themselves between the ignitor and the burner cap Remove any food deposits carefully see Cleaning and care food deposits have lodged themselves on the ignition safety device Remove any food deposits carefully see Cleaning and care For safety reasons you may not be able to re ignite the burner for about 5 minutes after a spillage 32 Optional accessories Miele offer acomprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances These can be ordered online at Miele www miele shop com or from Miele see back cover for contact details Ceramic and stainless steel hob cleaner 250 ml Removes heavy soiling limescale deposits and light discolouration Stainless steel conditioning agent 250 ml Removes water marks flecks and fingerprints Helps prevent re soiling E cloth microfibre cloth Removes fingerprints and light soiling 33 Safety instructions for installation This appliance must be installed and connected to services in accordance with local and national safety an
30. sponge can be used with Miele cleaning agent for ceramic and stainless steel hobs see Optional accessories Apply with even pressure following the direction of the grain To help prevent re soiling we recommend using Miele stainless steel conditioning agent after cleaning see Optional accessories Apply sparingly with a soft cloth following the instructions on the packaging Printed surfaces Flame symbols Remove any soiling which comes into contact with the printed flame symbols straight away Soiling particularly salty food or liquid and olive oil can cause damage if left on the printed surfaces for a long time Do not use the Miele ceramic and stainless steel hob cleaning agent on the printed flame symbols This would rub off the print Pan supports control knobs Remove the pan supports Clean the pan supports and the control knobs with a solution of warm water and a little washing up liquid applied with a soft sponge Stubborn soiling should be soaked first After cleaning dry all surfaces with a clean cloth Do not clean the pan supports in a dishwasher 29 Cleaning and care Burner Do not clean any parts of the burner in a dishwasher The burner should be dismantled and then cleaned by hand using a solution of warm water and a little washing up liquid applied with a soft sponge Parts of the burner that cannot be removed should be wiped clean with a damp cloth only The ignito
31. switch should be easily accessible after the appliance has been built in If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to protect the appliance with a suitable residual current device RCD When switched off there must be an all pole contact gap of at least 3 mm in the isolator switch including switch fuses and relays Important U K The appliance is supplied for connection to a 230 240 V 50 Hz supply with a 3 core cable The wires in the mains lead are coloured in accordance with the following code Do not connect the appliance to the Green yellow earth mains electricity supply by an Blue neutral extension lead These do not guarantee the required safety of the Brown live appliance WARNING Please make sure that the connection THIS APPLIANCE MUST BE data quoted on the data plate match EARTHED the household mains supply 47 Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the electrical wiring in the home should be tested by a qualified electrician The manufact
32. t table Z e pomer cap tang BEINEN m Finally secure the jets against l inadvertent loosening with sealing m Pull the control knobs off wax m Loosen screws Q9 53 Conversion to another type of gas Function test Check all gas fittings for leaks m Reassemble the appliance m Check the burner flame by operating the burner The flame must not go out on the lowest setting or when the control is turned quickly from a high to a low setting On the highest setting the flame must have a distinctive and visible core m Stick the label supplied with the jets above the label stating the type of gas being used 54 After sales service data plate guarantee In the event of any faults which you cannot remedy yourself or if the appliance is under guarantee please contact Your Miele dealer or the Miele Service Department see back cover for address Please note that telephone calls may be monitored and recorded to improve our service When contacting Miele please quote the model and serial number of your appliance which are given on the data plate N B A call out charge will be applied for service visits where the problem could have been resolved as described in these instructions Space in which to stick the extra data plate supplied with the appliance Ensure that the model number is the same as the one on the front of these instructions Guarantee For information on the appliance guaran
33. t 22 In operation indicator and Residual heat indicator n anaua uaaa aaa 24 Suitable pans 0 2 0 e 25 Energy saving Ups 26 Safety features 27 Cleaning and care 28 Stainless steel surfaces 0 0 0 ects 29 Pan supports control knobs 29 EUEDe ee ee Sn Ww eae ee EUN S tes tak yan wate s 30 Problem solving guide 31 Optional accessonies 33 Safety instructions for installation 0 0 eese 34 Appliance and building in dimensions 38 CS 10 12 2 sas seus pes ieee hee eee Se bon an sata Ro Pe AE EG 38 CS 1084 pM 39 Contents Preparing the worktop 40 Installation of several appliances lees 41 Fixing the spring clamps and spacer bars 43 Installing removing the appliance 45 General installation tips 46 Electrical connection 00002 47 Gas connection se corces erita stace i t nii EEE tetas 49 Conversion to another type of oas 51 CS 1012 1 aayr cem pee a arte ee e BER R RE san bee de N Baw aed 51 JEU TAG Mr P ETT 51 SOSE ee ee REUS Se 52 Jet table un nn aa E oue a a Ral e RR ee 52 Changing eebe oases sd RD owed ine ine Eka 53 Function test ua urn dX eet a E vade do Peta as Mp a eee detta 54 After sales service data plate guarantee Laaa 55 Gas heated appliances Safety precautions to take if you smell gas e Turn off the gas emergency control valve immediately This is usuall
34. tee specific to your country please contact Miele See back cover for contact details In the U K your appliance is guaranteed for 2 years from the date of purchase However you must activate your cover by calling 0845 365 6640 or registering online at www miele co uk 55 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Trading Ltd 1 3 Floor No 82 Shi Men Yi Road Jing an District 200040 Shanghai PRC Tel 86 21 6157 3500 Fax 86 21 6157 3511 E mail mieleshanghai cn miele com Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Manufacturer Germany Miele amp Cie KG Carl Miele Stra e 29 33332 G tersloh Ireland Miele Ireland Ltd 2024 Bianconi Avenue Citywest Business Campus Dublin 24
35. tion Rapid ignition system The appliance is supplied with a rapid ignition system with the following features Rapid ignition without pressing und holding the control Automatic re ignition Should the flame be extinguished by a gust of air the burner will re ignite automatically If re ignition is unsuccessful the gas supply will be cut off automatically see Safety cut off 22 Switching on adjusting the flame and switching off The control is used to ignite the burner and to regulate the strength of the flame e The gas supply is turned off Strong flame gt gt Weak flame The burners can only be switched on by pressing in the appropriate control and turning it anti clockwise and switched off by turning the control clockwise The following will cause damage to the appliance Switching the burner on without pressing the control down Switching the burner on by turning the control clockwise Switching the burner off by turning the control anti clockwise The manufacturer will not accept liability for any damage resulting from incorrect operation Operation Switching on m To ignite the burner press the control knob down and turn it anti clockwise to the large flame symbol The ignitor will make a clicking sound and ignite the gas Operating a control will automatically create a spark on every burner This is quite normal and does not indic
36. urer cannot be held liable for the consequences of an inadequate earthing system such as an electric shock The manufacturer cannot be held liable for damage which is the direct or indirect result of incorrect installation or connection 48 Gas connection N Connection to the gas supply or conversion from one type of gas to another should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations e g Gas Safe registered in the UK Every appliance should have its own easily accessible isolating valve and test point Check with your local gas supplier about the type of gas and its calorific value and compare this information with the type of gas quoted on the hob data plate This appliance is not connected to an exhaust flue Please ensure it has adequate ventilation after installation The installer is responsible for ensuring that the appliance functions correctly when installed Depending on country the hob is supplied ready for connection to natural or liquid gas refer to label on the appliance United Kingdom GB II 2 H 3 20 mbar 28 30 37 mbar Ireland IE Il 2 H 3 20 mbar 28 30 37 mbar Depending on country a set of jets for conversion to an alternative type of gas may be included with the hob Please contact your dealer or the Miele Spare Parts Department for the appropriate conversion jets if necessary
37. y located near the gas meter e Eliminate all sources of ignition in a safe manner Do not smoke light cigarette lighters or matches e Do not operate electrical lights or switches i e do not switch them On or Off e Open all doors and windows to ventilate the area e f the smell of gas persists evacuate the building In the UK you must now e Call the Gas Emergency Contact Centre Tel 0 800 111 999 For any gas work in the UK always use a Gas Safe registered engineer GAS safe REGISTER In other countries please follow relevant country specific procedures on gas Guide to the appliance CS 1012 1 Large burner Controls 2 Medium burner rear 3 Pan support front 4 Symbols to indicate which gas burner the control is for 8 Display Display es 2 In operation indicator 43 Residual heat indicator Guide to the appliance CS 1034 1 Large burner Controls 2 Small burner 6 front right Large burner 9 rear right 4 Medium burner 9 rear left Pan supports A front left Symbols to indicate which gas burner the control is for Display Display se 2 In operation indicator 43 Residual heat indicator Guide to the appliance Burner Burner cap 4 Burner head Ignition safety device amp 2 Ignitor Burner base Warning and Safety instructions This appliance complies with all current local and national safety r
Download Pdf Manuals
Related Search