Home
Samsung SCD-2020R
Contents
1. SAMSUNG TECHWIN High Resolution D N IR Dome Camera User Manual SCD 2020R High Resolution DAN IR Dome Camera User Manual Copyright 2010 Samsung Techwin Co Ltd All rights reserved Trademark SAMSUNG TECHWIN EP is the registered logo of Samsung Techwin Co Ltd The name of this product is the registered trademark of Samsung Techwin Co Ltd Other trademarks mentioned in this manual are the registered trademark of their respective company Restriction Samsung Techwin Co Ltd shall reserve the copyright of this document Under no circumstances this document shall be reproduced distributed or changed partially or wholly without formal authorization of Samsung Techwin Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document but no formal guarantee shall be provided Use of this document and the subsequent results shall be entirely on the user s own responsibility Samsung Techwin reserves the right to change the contents of this document without prior notice Warranty If the product does not operate properly in normal conditions please let us know Samsung Techwin will resolve the problem for free of charge The warranty period is 3 years However the followings are excluded If the system behaves abnormally because you run a program irrelevant to the system operation Deteriorated performance or natural worn out in process of time Before opera
2. EXPOSURE SETUP SHUTTER You can select either auto or P BRIGHTNESS S NIAI manual shutter mM ESC E 3 AGC HIGH ESC Select this to control the shutter 4 SENS UP OFF speed automatically If ESC is 5 RETURNg selected the shutter speed is automatically controlled depending on the ambient illumination of the subject MANUAL You can control shutter speed manually A FLK Select this when you experience picture flicker which can happen when there is a clash with the frequency of the installed lighting e AGC AUTO GAIN CONTROL The higher the gain level the brighter the screen but the higher the noise OFF Deactivates the AGC function LOW Allows automatic gain control from 5 3dB to 32dB HIGH Allows automatic gain control from 5 3dB to 37dB SENS UP When it is night or dark the camera automatically detects the light level and maintains a clear picture if this mode is activated OFF Deactivates the SENS UP function Press SET to Return AUTO Activates the SENS UP function Y When the SHUTTER is set to MANUAL or A FLK mode SENS UP will be disabled e RETURN Select this to save the changes in the EXPOSURE menu and return to the SETUP menu 20_ setup Y lf you press the Function Setup switch in AUTO mode You can adjust brightness by adjusting the SENS UP level X2 x512 Note that the higher the SENS UP level the brighter the screen but the more li
3. Y White Balance may not work properly under the following conditions In this case select the AWC mode When the color temperature of environment surrounding the subject is out of the control range e g clear sky or sunset When the ambient illumination of the subject is dim If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable SSDR SAMSUNG SUPER DYNAMIC RANGE SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas 1 When the SETUP menu screen is displayed select SSDR by using the Function Setup MAIN SETUP Switch so that the arrow indicates SSDR 1 LENS SHADE 2 EXPOSURE4 2 Use the Function Setup switch to change 3 WHITE BAL the SSDR level in the sub menu according gt 4SSDR to the contrast between bright and dark 5 BACKLIGHT areas SSDR OFF 22_ setup BACKLIGHT This camera is designed so that it delivers a distinctive subject and background at the same time even when the subject is in backlight unlike conventional cameras by adopting a proprietary W V DSP chip 1 When the SETUP menu screen is displayed MAIN SETUP select BACKLIGHT by using the Function 1 LENS SHADE Setup switch so that the arrow indicates 2 EXPO
4. NOT SAVE RESET MENU SETUP Use the Function Setup switch beside of the lens 1 Press the Function Setup switch Main setup menu is displayed on the monitor screen 18 setup Function Setup switch MAIN SETUP Select the functio gt 1 LENS SHADE Change the status by moving up or 2 EXPOSURE 1 by moving the down direction 3 WHITE BAL setup switch left or of function setup 4 SSDR right switch 5 BACKLIGHT 6 SSNR3 7 DAY NIGHT 8 5 9 EXIT dnias 2 Select a desired function using the Function Setup switch Place the cursor over a desired item 3 Set up a selected item by using the Function Setup switch 4 To finish the setting select EXIT and press the Function Setup switch Y An item with the con also has sub menus To select a sub menu select an item with the icon and press the Function Setup switch An item with the icon is unavailable due to function settings LENS SHADE LENS SHADE diminishes brightness contrast to obtain balanced view on the monitor OFF LENS SHADE NOT IN USE ET ON LENS SHADE IN USE FIRES 2 EXPOSURE _ English_19 setup EXPOSURE 1 When the SETUP menu screen is displayed MAN SETUP select EXPOSURE by using the Function 11ENS SHADE Setup switch so that the arrow indicates 2 EXPOSURE Ed EXPOSURE 3 WHITE BAL 2 Select a desired mode using the Function Setup switch BRIGHTNESS Adjusts the video brightness
5. is not activated in light or overly dark conditions function does not work in D amp N B W mode SSNR3 This function reduces the background noise in a low luminance environments 1 When the SETUP menu screen is displayed select SSNR3 by using the Function Setup LENS Pres SETUP Switch so that the arrow indicates SSNR3 2 EXPOSURE 2 Select a desired mode using the Function 3 WHITE BAL Setup switch 4 SSDR e OFF Deactivates SSNR3 so that noise is y Ec not reduced 7 DAYINIGHT ON Activates SSNR3 so that noise is reduced 3 Set the SSNR3 mode to ON and press the Function Setup switch Then you can adjust SSNR3 the noise reduction level LENS NEST 10 Press SET to Return Y You cannot set the SSNR3 to ON or OFF when the AGC mode of the EXPOSURE menu is OFF When adjusting the noise reduction level of the SSNR3 mode remember that the higher the level set the more the noise level will be reduced but that after image may also occur 24 setup DAY NIGHT You can display pictures in color or black and white 1 When the SETUP menu screen is displayed select DAY NIGHT by using the Up and MAIN SETUP Down buttons so that the arrow indicates SHADE DAY NIGHT 2 EXPOSURE 3 WHITE BAL 2 Select a desired mode using the Left and ASSDR Right buttons according to the picture 5 BACKLIGHT display you want gt 6 SSNR3 COLOR The picture is always displayed T DAYINIGH
6. sec Digital Zoom Off On 1x 16x Flip Mirror On Off Communication Coaxial Control SPC 300 Compatible Protocol Pelco C Coaxitron IR Distance 7m IR LED 8 EA Environmental pares Temperature 40 6 _ 450 C 14 F 122 F Less than 90 RH Electrical Input Voltage 12V DC 10 Power Consumption 2 5W Mechanical Color Material Body Ivory PC ABS Dome Cover Clear PC Dimension WxHxD 0107 6 x 83 7mm Weight 280g x This specification can be changed without notice for performance improvement of product English 33 SNOILVOIJIO3dS O specifications DIMENSION 0107 6 SAMSUNG 83 7mm 939 e o Y S 81 6mm 34 specifications a m gt rm m m 7 7 TT on gt DECLARATION OF CONFORMITY Application of Council Directive s Manufacturer s Name Manufacturer s Address European Representative Name European Representative Address Equipment Type Environment Model Name Beginning Serial NO Conformance to 89 336 EEC SAMSUNG TECHWIN CO LTD SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 CCTV Camera SCD 2020RP 01153010007 EN 50081 1 1992 EMC Directive 89 336 EEC and 92 31 EEC EN 50130 4 1996 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer SAMSUNG TECHWIN CO LTD Legal Representat
7. using an LCD monitor gt GAMMA 0 55 You can change the gamma PED LEVEL 17 PED level and color gain in the COLOR GAIN sub menus RESET 1 CRT Please select this menu item when Press SET to Retum using a CRT monitor You can change the PED level color gain in the sub menus USER Please use this menu item when using a monitor other than standard ones You can change the gamma PED level and color gain in the sub menus CAM TITLE If you enter a title the title will appear on CAMERA TITLE SETUP the monitor ABCDEFGHIJKLM If the SPECIAL menu screen is NOPQRSTUVWXYZ displayed use the Function Setup abcdefghijkim switch so that the arrow indicates CAM TITLE Set it to ON by using the Function Setup switch nopqrstuvwxyz 0123456789 gt CLR POS END When the CAM TITLE menu is OFF no title will be displayed on the monitor screen even if you enter one Only English is available in the mode Press the Function Setup switch Use the Function Setup switch to move to a desired letter and select the letter by pressing the switch Repeat this to enter multiple letters You can enter up to 15 letters English_27 setup Y Ifyou move the cursor to CLR and press the Function Setup switch all the letters are deleted To edit a letter change the cursor to the bottom left arrow and press the Function Setup switch Move the cursor over the letter to be edite
8. CTION INSTALLATION CONNECTION SETUP TROUBLESHOOTING SPECIFICATIONS 8_ contents 10 11 12 15 16 16 18 18 31 32 34 Features What s included Component names and Functions Installation the panning and tilting while watching the monitor Connecting to Monitor Connecting to Power Menu Configration Menu Setup Troubleshooting Specifications Dimension introduction FEATURES Excellent Sensitivity The Built in high sensitivity COLOR CCD enables a clear image even in OLux B W IR LED ON or lower illumination Ultra High Resolution By adopting a diagonal 6mm 1 3 410 000 NTSC pixels 470 000 PAL pixels SONY CCD the camera produces clear picture quality with a horizontal resolution of 600 TV lines for color and 700 TV lines for BW NOLLONGOHINI SSNR3 Samsung Super Noise Reduction Function The high performance W V DSP chip effectively removes low light gain noise and afterimage to provide clear images even in dark environments Day amp Night The camera identifies whether it is day or night and automatically switches to the appropriate mode depending on its environment By day the camera switches to color mode in order to maintain optimal color At night it switches to BAN mode so as to obtain better picture definition DIS Digital Image Stabilizer The DIS function compensates for any camera movement to produce more stable pictures Indoor Vi
9. Horizontal Resolution Color 600 TV lines B W 700 TV lines Min Illumination Color 0 15Lux F1 2 50IRE B W OLux IR LED on S N Ratio 52dB AGC off Weight on Video Output CVBS 1 0 Vp p 750 composite Lens Type Focal Length Zoom Ratio 3 6 mm Max Aperture Ratio F2 0 Angular Field of View 66 H x 49 V Min Object Distance 0 4 m Pan Tilt Pan Range 0 352 Tilt Range 0 75 OPERATIONAL On Screen Display Multi language Support by Coaxial Cable English Japanese Spanish French Portuguese Taiwanese Korean Multi language Support by Coaxial Cable English French German Spanish Italian Chinese Russian Polish Czech Romanian Serbian Swedish Danish Turkish Portuguese Camera Title Off On Displayed 15 characters Day amp Night Auto ICR Color B W 32 specifications SCD 2020RN SCD 2020RP Backlight Compensation Contrast Enhancement SSDR Off On Digital Noise Reduction SSNR III Off On Digital Image Stabilization Off On BLC HLC Off Motion Detection Off On 8 programmable zones Privacy Masking Off On 12 programmable zones ros A AA Gain Control Low High Off White Balance ATW Outdoor Indoor Manual AWC 1 700K 11 000K EM Shutter 1 60 1 120 000 sec 1 50 1 120 000
10. NSTALLATION 1 Separate the dome cover by counterclockwise rotation Latch Main Body Camera Unlocking Locking Direction direction Clockwise Figure 1 bs gt ES Dome Cover 27 To install the dome cover on the camera body turn the latches in locking direction as shown in the figure 1 The installation should be done by qualified service personnel or system installers f the ceiling material is not strong enough to hold the installation screws the camera may fall off Reinforce the ceiling as needed To change the position of the cable take away the Hole Cover and pass the cable through Original position of the cable Hole Cover 12_ installation WHEN USING THE CEILING BRACKET An arrow for installing Ceiling bracket directions tapping screw provided f uem 7 des aci e Unlocking direction Dome Cover 1 Hold the ceiling bracket located where the arrow points to and separate it from the main body of the camera by rotating it counterclockwise refer to the picture in Notes on page 12 2 Adjust the camera lens to face the area to be monitored and fix the main body and the dome cover by aligning the grooves and rotating the body clockwise English 13 NOILVTIVISNI O installation Pan Base fixation screw M4 tapping Screw Figure 2 Y If you want to install the camera with the ceiling bracket combined fix it using two tap
11. SETUP menu screen is displayed select SPECIAL by using the Function 11ENS Pres SETUP Setup switch so that the arrow indicates 2 EXPOSURE SPECIAL 3 WHITE BAL 4 SSDR 5 BACKLIGHT 6 SSNR3 7 DAY NIGHT b 9 EXIT 2 Select a desired mode using the Function SPECIAL Setup switch gt IMAGE ADJ 1 2 MONITOR 10041 3 CAM TITLE OFF 4 SYNC INT 5 MOTION DET OFF 6 PRIVACY OFF DIS OFF LANGUAGE ENGLISH RETURN4 IMAGE ADJ IMAGE SETUP 1 When the SPECIAL menu screen is gt 1V REV displayed select IMAGE ADJ by using REV the Function Setup switch so that the D Z00M arrow indicates ADJ 2 Select a desired mode using the Function Setup switch V REV You can flip the picture vertically on the screen SHARPNESS RETURN at 2 3 4 FONT COLOR 5 6 H REV You can flip the picture horizontally on the screen D ZOOM You can use a digital zoom of x1 x16 26 setup FONT COLOR You can change the OSD font color White Yellow Green Red Blue SHARPNESS As you increase this value the picture outline becomes stronger and clearer Adjust this value appropriately depending on the sharpness ofthe picture RETURN Select this to save the settings for the IMAGE ADJ menu and to retum to the SPECIAL menu dnias e Monitor Please change the settings value of video appropriate to your monitor LCD Please select this menu item LCD MONITOR when
12. SURE4 BACKLIGHT BAL 2 Select a desired mode using the Function Setup p gt 5 BACKLIGHT Switch depending on the camera purpose 6 SSNR3 Enables a user to directly select a desired area from a picture and to view the area more clearly Select BLC to adjust the area to be can mask out much of the on screen detail LIMIT LEVEL Adjusts the brightness level of a monitoring area LIMIT Enable to change the operating condition MASK COLOR TONE Change the color brightness of the masking area Black Red Blue Cyan Magenta TOP LEFT RIGHT BLC SETUP enhanced and enhancement level gt LEVEL MIDDLE TOP man 38 BOTTOM en 109 LEFT mn 54 RIGHT nn 121 Press SET to Return High Light Compensation Ifthe scene contains extremely bright light HLC SETUP areas such as from car headlight the light LEVEL MIDDLE NIGHT ONLY MASK COLOR BLACK MASK TONE a ka UU BOTTOM TEST ka UT TEST Press SET to Return English_23 dnias setup e OFF Not being used 3 Select a desired mode using the Function Setup switch and press the switch Y Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC performance In a dark environment the HLC is only activated when a high light that is larger than a certain area is present The HLC
13. T in color B SPECIAL _ B W The picture is always displayed in black and white IR MODE When IR LED is turned on in B W the objects can be clearly identified due to the function that decreases screen saturation of objects within a short distance AUTO The mode is switched to Color in a normal environment but AUTO SETUP switches to B W mode when gt 1 BURST MODE ON ambient illumination is low To set 2 COLOR gt B W up the switching time for AUTO DURATION FAST mode press the Function Setup DWHETIME 3 SEC 6 3 B W gt COLOR switch You can turn on or off the DURATION FAST burst signal on B W mode DWELL TIME 10 SEC BURST MODE You can turn on or 4 RETURN 1 off the burst signal on B W mode DWELL TIME You can select the duration time about changing the day night mode 3s 55 7s 10s 15s 20s 305 40s 60s DURATION You can select the brightness level at which the camera Switches from day to night mode Color BW B W Color Fast 2 5 lux 5 lux Slow 1 lux 10 lux X Light levels are often site dependant English_25 dnias setup Y You cannot control the DAY NIGHT menu when AGC in the EXPOSURE menu is OFF At this time the exchange between DAY mode and NIGHT mode operates as like selecting COLOR mode The OSD key does not work for 3 seconds when switching to Color or B W to ensure stable camera operation SPECIAL 1 When the
14. d move the cursor to the letter to be inserted and then press the Function Setup switch Enter a title move the cursor to POS and press the Function Setup switch The entered title appears on the screen Select the position to display the title on the screen by using the Function Setup switch and press When the position is determined select END and press the Function Setup switch to retum to the SPECIAL menu SYNC Because the input power of SCD 2020R is DC SYNC is fixed at INT INT Internal Synchronization Type MOTION DET This product has a feature that allows you to observe movement of objects in 8 different areas on the screen and the words MOTION DETECTED appear on the screen when movement is detected You can monitor activity more efficient When the SPECIAL menu screen is displayed press the Function Setup MOTION DET switch so that the arrow indicates gt 1 SENSITIVITY AREM MOTION DET 2AREA MODE ON Set up the mode using the Function 3SELPOS L TOP Setup switch 4XPOS amm 3 5NPOS AS SENSITIVITY 6 ALL SET You can select up to 8 MD areas TRETURN When SENSITIVITY number is high motion detection sensitivity is increased to recognize even small movement AREA MODE Determines whether to use the MD area selected in SENSITIVITY SEL POS Determines which of the 4 vertices of each MD area is to be used 28 setup XPOS Determines the coordinate of the
15. ers should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery retum system 6_ safety information J O NK a important safety instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth 109 0 E Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers or other apparatus includin
16. function uses the digital zoom the camera s resolution will decrease DIS doesn t operate when background illumination is too low DIS doesn t operate when object pattern is monotonic as like sky or white wall If DIS is enabled the digital zoom is not configured to less than 46 level LANGUAGE You can select the menu language according to your requirements RETURN Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose SAVE Save the current settings and exit the MAIN SETUP menu NOT SAVE Do not save the current settings and exit the MAIN SETUP menu e RESET Resets the camera settings to the factory defaults Language and Monitor settings are not initialized 30_ setup troubleshootina TROUBLESHOOTING If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician PROBLEM SOLUTION Nothing appears on the screen Check that the power cord and line connection between the camera 3 and monitor are fixed properly gt Check that you have property connected VIDEO cable to the camera m 4 Mm VIDEO output jack ES A o The image on the screen is dim gt Is the lens stained with dirt Clean your lens with a soft clean cloth 3 Check the monitor a
17. g amplifiers that produce heat NOILVINHOHNI AL34VS O 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If he provided plug does nat fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus 13 Unplug this apparatus when a card is used Use caution when moving he cart apparatus combination to avoid injury from tip over 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 7_ important safety instructions English_7 contents INTRODU
18. horizontal axis for SEL POS YPOS Determines the coordinate of the vertical axis for SEL POS FILL SET Fills in a selected MD area The color of filling is sequentially selected as brown orange blue cyan yellowish green yellow magenta and red RETURN Select this to save the MOTION DET menu settings and return to the SPECIAL menu dnias Y MD areas show only MOTION DET menu Therefore MD areas don t display on the monitor screen PRIVACY Mask an area you want to hide on the screen When the SPECIAL menu screen is displayed press the Function Setup PRIVACY switch so that the arrow indicates 4 er AEN ns 3 MASK COLOR GREEN Set up the mode using the Function 4 MASK TONE munu 1 Setup switch 5 TOP Nak IN 39 AREA SEL You can select up to 8 6 BOTTOM tum 79 PRIVACY areas 7 LEFT MINUIT 13 8 RIGHT EST 52 9 RETURN MODE Determines whether to use the area selected in the AREA SEL and the size and position of the area MASK COLOR Determine area color You can select GREEN RED BLUE BLACK WHITE and GRAY MASK TONE Adjust the brightness of MASK COLOR TOP BOTTOM LEFT RIGHT Adjust the size and position of the selected area RETURN Select this to save the PRIVACY menu settings and return to the SPECIAL menu DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind English 29 setup As the DIS
19. is turned off CONNECTING TO POWER Connect the adaptor to the power input connector as shown in the figure below The recommended adaptor specification for SCD 2020RN P is DC 12V 500mA Power Input Terminal 16_ connection When the resistance value of copper wire is at 20 C 68 F Copper wire size 24 22 20 18 AWG 0 22mm2 0 33mm2 0 52mm2 0 83mm2 Resistance Q m 0 078 0 050 0 030 0 018 Voltage Drop V m 0 028 0 018 0 011 0 006 As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may af fect the performance of the camera Standard voltage for camera operation DC 12V 10 There may be some deviation in voltage drop depending on the type of wire and the manufacturer Y Be sure to connect power only after all the installation is complete Ground should be connected to the GND terminal English 17 setup MENU CONFIGRATION Setup Menu LENS SHADE BRIGHTNESS SHUTTER AGC FXPOSURE 0 SENS UP RETURN WHITE BALANCE ATW OUTDOOR INDOOR MANUAL AWC SET SSDR OFF ON BACKLIGHT OFF BLC HLC SSNR3 ON OFF DAY NIGHT AUTO COLOR B W IMAGE ADJ MONITOR CAM TITLE SPECIAL SYNC MOTION DET PRIVACY DIS LANGUAGE RETURN EXIT SAVE
20. ive in Europe Signature BI Gu Signature Full Name BONJENG GU Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON KOREA Place MEMO MEMO MEMO MEMO SALES NETWORK SAMSUNG TECHWIN CO LTD Samsungtechwin R amp D Center 701 Sampyeong dong Bundang gu Seongnam si Gyeonggi do Korea 463 400 TEL 82 70 7147 8740 60 FAX 82 31 8018 3745 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Park Tol Free 1 877 213 1222 FAX 1 310 632 2195 Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungsecurity com P NO 26806144801 01
21. kely it is that an after image will appear Although Noise Spots and Whitish symptoms may occur in SENS UP operation when the sens up level is increased this is normal WHITE BALANCE WHITE BAL Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select White Bal by using the Function MAIN SETUP SER 1 LENS SHADE Setup switch so that the arrow indicates White Bal 2 EXPOSURE4 Ngan gt 3 WHITE BAL 2 Select a desired mode using the Function 4 SSDR Setup switch x Select one of the following 5 modes as appropriate for your purpose ATW Select this when the color temperature is between 1 700 K and 11 000 K OUTDOOR Select this when the color temperature is between 1 700 K and 11 000 K sodium light inclusion INDOOR Select this when the color temperature is between 4 500 K and 8 500 K MANUAL Select this to fine tune White Balance manually Set White Balance first by using the ATW or AWC mode After that switch to MANUAL mode fine tune the White Balance and then press the Function Setup switch WB MANUAL gt RGAIN 529 BGAIN umso 532 Press SET to Return AWC SET To find the optimal luminance level for the current environment point the camera towards a sheet of white paper and press the Function Setup switch If the environment changes readjust it English_21 dnias setup
22. nd DVR settings o If the camera is exposed to very strong light change the camera position The image on the screen is dark gt Adjust the contrast feature of the monitor or DVR gt If you have an intermediate device set the 750 Hi z properly The camera is not working Check that you have properly connected the camera to an appropriate properly and the surface of the Power source camera is hot The DAY NIGHT menu does not Check that AGC of EXPOSURE SETUP menu is OFF work The SENS UP function does not Check that AGC of EXPOSURE SETUP menu is OFF work Check that SHUTTER of EXPOSURE SETUP menu is A FLK or The pag Detection function does ps Check that MOTION DEF of SPECIAL SETUP menu is OFF not work Color is not correct gt Check the setting of WHITE BAL SETUP menu The screen flickers continually gt Check that the camera is not pointing at the sun IR LED isn t lighted Isn t DAYNIGHT function setting up the color mode D gt Please change the AUTO or BAW mode English_31 specifications SPECIFICATIONS SCD 2020RN SCD 2020RP VIDEO Imaging Device 1 3 Super HAD CCD Total Pixels 811 H x 508 V 795 H x 596 V Effective Pixels 768 H x 494 V 752 H x 582 V Scanning System 2 1 Interlace Synchronization Internal Frequency H 15 734KHz V 59 94Hz H 15 625KHz V 50Hz
23. oduct 3 Do not connect multiple cameras to a single adapter Exceeding the capacity may cause abnormal heat generation or fire 4 Securely plug the power cord into the power receptacle insecure connection may cause fire 5 When installing the camera fasten it securely and firmly The fall of camera may cause personal injury 4 safety information 6 Do not place conductive objects e g screwdrivers coins metal parts etc or containers filled with water on top of the camera doing so may cause personal injury due to fire electric shock or falling objects 7 Do not install the unit in humid dusty or sooty locations doing so may cause fire or electric shock 8 If any unusual smells or smoke come from the unit stop using the product in such case immediately disconnect the power source and contact the service center continued use in such a condition may cause fire or electric shock 9 If this product fails to operate normally contact the nearest service center never disassemble or modify this product in any way samsung is not liable for problems caused by unauthorized modifications or attempted repair 10 When cleaning do not spray water directly onto parts of the product doing so may cause fire or electric shock CAUTION 1 Do not drop objects on the product or apply strong shock to it Keep away from a location subject to excessive vibrationor magnetic interference 2 Do not install in a loca
24. ping screws at the side of the main body refer to the Figure 2 on page 14 14_ installation le ADJUST THE PANNING AND TILTING WHILE WATCHING THE MONITOR Tilt Base fixation screw 7595 Pan Base fixation Screw NOILVTIVISNI O 1 You can adjust the camera to point in any direction by using the pan Tilt mechanism Pan Base can rotates by 176 total 352 Tilt Base covers 75 angle 2 Methods of adjustment The case of wall installation After mounting the camera on a wall adjust the panning angle so that the correct viewing angle is attained and the titling is correctly orientated And then adjust the tilting angle by rotating the tilt base Tighten pan and tilt securing screw The case of ceiling installation After mounting the camera on a ceiling adjust the panning angle so that the correct viewing angle is attained and the titling is correctly orientated 0 And then adjust the tilting angle by rotating the tilt base Tighten pan and tilt securing screw Y When you want to adjust the Pan Tilt Base loosen adjust and then tighten the Pan Tilt Base screws English_15 connection CONNECTING TO MONITOR Connect the VIDEO OUT jack to the VIDEO IN jack of monitor Monitor lt Y CCTV Camera connecting method varies with the instruments refer to the manual supplied with the instrument Only connect the cable when the power
25. rence when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations of ICES 003 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business us
26. sibility range 7M In B W mode the IR LEDs are illuminated the indoor visibility range at O Lux is 7M IR MODE Function The intensity of the IR LEDs automatically adjust depending upon the closeness of the object to prevent saturation Lens Shading Compensation LENS SHADE reduces the brightness contrast to obtain a more balanced image on the monitor OSD The camera control is convenient by using 9 different foreign language O S D NTSC English Japanese Spanish French Portuguese Taiwanese Korean PAL English French German Spanish Italian Chinese Russian Polish Czech Romanian Serbian Swedish Danish Turkish Portuguese English 9 introduction Miscellaneous Functions HLC High Light Compensation SENS UP FLIP H V REV D ZOOM SHARPNESS MOTION DETECTION and PRIVACY functions are provided WHAT S INCLUDED Check if the following items are included in the product package ME S SCD 2020R Instruction Manual M4 Tapping Screw 3EA d 10 introduction COMPONENT NAMES AND FUNCTIONS FRONT NOLLONGOHINI O Pan Base control panning angle of camera Tilt Base control tiling angle of camera Lens Module f 3 6mm F2 O IR Lens O Power Input Connector Video Output Jack O Function Setup Switch displays the OSD menu and moves the cursor up down left and right amend or confirm changes Dome Cover English_11 installation I
27. ting the camera confirm the camera model and correct input power voltage To help you understand this manual thoroughly we ll introduce our model description W SCD 2020R SERIES NTSC MODEL PAL MODEL SCD 2020RN SCD 2020RP W MODEL DESCRIPTION SCD 2020RX m SIGNAL SYSTEM SIGNAL SYSTEM N NTSC MODEL P PAL MODEL safety information AN CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING To prevent damage which may result in fire or electric shock hazard do not expose this appliance to rain or moisture To prevent injury this apparatus must be securely attached to the floor wall in accordance with the installation instructions WARNING 1 Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product 2 Incorrectly connecting the power supply or replacing battery may cause explosion fire electric shock or damage to the pr
28. tion subject to high temperature over 50 C low temperature below 10 C or high humidity Doing so may cause fire or electric shock 3 If you want to relocate the already installed product be sure to turn off the power and then move or reinstall it 4 Remove the power plug from the outlet when then there is a lightning Neglecting to do so may cause fire or damage to the product 5 Keep out of direct sunlight and heat radiation sources It may cause fire 6 Install it in a place with good ventilation 7 Avoid aiming the camera directly towards extremely bright objects such as sun as this may damage the CCD image sensor 8 Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids Such as vases shall be placed on the apparatus 9 The Mains plug is used as a disconnect device and shall stay readily operable at any time English 5 NOLLVINHOHNI AL34VS O safety information FCC STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interfe
Download Pdf Manuals
Related Search
Related Contents
Sonab OA5 mkII EUROLITE LED WMS 8-fold set RBG User Manual OP-STC01 Samsung GT-C3300I Инструкция по использованию Stavbna dediščina in kultura bivanja v Karavankah MODE D`EMPLOI des fiches abc-aide-soignante Guida dell`utente Copyright © All rights reserved.