Samsung SCV-2080
Contents
1. 450m SC2VRG 6 U 600m 7C2VIRG 11 U Notes e itis recommended that pure copper coax cable is used and not copper coated steel as this will cause issues with the communication over the coaxial cable Use the Function Setup switch within the camera Function Setup switch 1 Press the Function Setup switch e Main SETUP menu is displayed on the monitor screen Select the function using gt i LENS the Function Setup switch Change the status using the Function Setup switch 2 Select a desired function using the Function Setup switch e Place the cursor over a desired item 3 Set up a selected item by using the Function Setup switch 4 To finish the setting select EXIT and press the Function Setup switch e An item with the lt icon also has sub menus To select a sub menu select an item with the icon and press the Function Setup switch e An item with the icon is unavailable due to function settings Using this function you can control the screen brightness 1 When the SETUP menu screen is displayed select LENS by using the Function Setup switch so that the arrow indicates LENS 2 The Lens mode has sub menu site as listed below BRIGHTNESS Adjusts the video brightness FOCUS ADJ To adjust the lens focus correctly you must activate the Focus Settings mode To activate the Focus Settings mode adjust the lens focus and then deactivate the setti2. SAMSUNG TECHWIN High Resolution Vandal Dome Camera User Manual SCV 2080 High Resolution Vandal Dome Camera User Manual Copyright 2009 Samsung Techwin Co Ltd All rights reserved Trademark SAMSUNG TECHWIN gg is the registered logo of Samsung Techwin Co Ltd The name of this product is the registered trademark of Samsung Techwin Co Ltd Other trademarks mentioned in this manual are the registered trademark of their respective company Restriction Samsung Techwin Co Ltd shall reserve the copyright of this document Under no circumstances this document shall be reproduced distributed or changed partially or wholly without formal authorization of Samsung Techwin Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document but no formal guarantee shall be provided Use of this document and the subsequent results shall be entirely on the user s own responsibility Samsung Techwin reserves the right to change the contents of this document without prior notice Warranty Samsung Techwin Co Ltd shall reserve the copyright of this document Under no circumstances this document shall be reproduced distributed or changed partially or wholly without formal authorization of Samsung Techwin Before operating the camera confirm the camera model and correct input power voltage To help you understand this manual thoroughly we ll introduce our mo
3. and exit the MAIN SETUP menu NOT SAVE Do not save the current settings and exit the MAIN SETUP menu RESET Resets the camera settings to the factory defaults Language and Monitor settings are not initialized If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician Nothing appears on the screen gt Check that the power cord and line connection between the camera and monitor are properly connected gt Check that you have properly connected BNC cable to the camera The image on the screen is dim gt Is lens stained with dirt Clean your lens with soft clean cloth Set the monitor or DVR to the proper condition gt If the camera is exposed to very strong light change the camera position The image on the screen is dark gt Adjust the contrast feature of the monitor or DVR gt If you have an intermediate device set the 750 Hi z properly The camera is not working properly and the surface of the camera is hot gt Check that you have properly connected the camera to an appropriate power source The DAY NIGHT menu does not work Check that AGC of EXPOSURE SETUP menu is OFF The SENS UP function does not work gt Check that AGC of EXPOSURE SETUP menu is OFF gt Check that SHUTTER of EXPOSURE SETUP menu is A FLK or MANUAL Color is not correct gt Check the setti
4. to the dust and rain High Resolution By adopting a diagonal 6mm 1 3 410 000 NTSC pixel 470 000 PAL pixel SONY CCD the camera produces clear picture quality with a horizontal resolution of 600 TV lines in color and a horizontal resolution of 700 TV lines in B W mode Excellent Sensitivity The built in high sensitivity COLOR CCD produces aclear image Color 0 15Lux 50IRE F1 2 0 0003LUX SENS UP x512 B W 0 001Lux 50IRE F1 2 0 000002LUX SENS UP x512 SSNR3 Samsung Super Noise Reduction Function The high performance W V DSP chip effectively removes low light gain noise and afterimage to provide clear images even in dark environments DAY amp NIGHT ICR This camera has a function that automatically selects the mode that is appropriate for daytime or night time conditions The COLOR mode operates in daytime Conditions to provide optimum colors and B W mode operates in night time conditions to enhance the definition of the image Motion Detection Since the camera detects motion without any additional external sensor you can monitor activity more efficient SSDR Samsung Super Dynamic Range For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness DIS Digital Image Stabilizer The
5. DIS function compensates for any camera movement to produce more stable pictures Communication Coaxial communication methods are supported Protocol Pelco Coaxitron Miscellaneous Functions HLC High Light Compensation SENS UP FLIP H V REV D Z00M SHARPNESS and PRIVACY functions are provided osp The camera s OSD is complimented by 18 languages NTSC Korean English French Spanish Japanese Portuguese Taiwanese PAL English Chinese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese COLOR DOME CAMERA 6 SCV 2080 Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment and is taking a number of steps to provide customers with more environment friendly products The Eco mark represents Samsung Techwin s will to create environment friendly products and eco RoHS compliant indicates that the product satisfies the EU RoHS Directive QO Warnings amp Cautions This information is provided to ensure your safety and to prevent any losses financial or otherwise Please read it carefully and use the product accordingly For product inquiries please contact the retail shop where you bought the camera The use of equipment such as an aerial ladder while providing after sales service shall be at your expense Separate the power plug during a thunder storm This product is support equipmen
6. LOR BW AUTO ICR Type Gain Control Low High Off White Balance ATW Outdoor Indoor Manual AWC 1 700 K 11 000 K SENS UP frame Integration Auto Off Selectable x2 x512 Motion Detection On Off 8 Programmable zones Privacy Masking On Off 12 Programmable zones 3D Noise Filter SSNRII On Off Level adjustable Digital Zoom On Off x1 x16 Digital Image Stabilization DIS On Off Camera Title On Off Displayed 15 Characters Sharpness On Off Level adjustable Flip Mirror On Off Operating Temperature Hu CoaxialPelco Coaxitror 50 C ture Hu Dimension Weight O160 W x134 5 Hjmm 1 26Kg u The specification for this product may change without prior notice for product improvement DECLARATION OF CONFORMITY Application of Council Directive s 2004 108 EC Manufacturer s Name SAMSUNG TECHWIN CO LTD Manufacturer s Address SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 European Representative Name European Representative Address Equipment Type Environment CCTV Camera Model Name SCV 2080P Beginning Serial NO C5CX6V3Z300001X Year of Manufacture 2010 03 01 Conformance to EN 55022 2006 EN 50130 4 2003 We the undersigned hereby declare that the equipment specified above conforms
7. amp Use only under temperature conditions between 50 C and 50 C Provide good ventilation when using in high temperature conditions eke HIN Severe lighting changes or flickering may hinder normal camera operation amp May cause a product malfunction Bis May lower image quality The lens is the most important component of the camera Be careful not to smear it with fingerprints Pi es May damage the ae oe Exposure to a spotlight or an object emitting strong light may cause smear or blooming Ensure that the power source complies with normal specifications before supplying it to the camera High Resolution Vandal Dome Camera SCV 2080 Instruction Manual Quick Install Guide Template Cable for test monitor connection Plastic Anchor 4 EA L wrench Fixing Screws 4 EA Tapping Screws 4 EA Pan Base Control panning angle of camera Rotate Base Control rotating angle of camera x3 6 Vari focal Lens Module 2 8 10 0mm F1 2 Video Output Terminal to Monitor Function Setup switch Display the menu on the screen and move the cursor to four directions to confirm status or changing a selected item Video Output Jack Power Input Terminal Dome Cover Inner cover Wing locker Lock releaser 1 Using the L wrench provided loosen 3 screws by turning them counterclockwise and separat
8. ance e When dark the HLC is only activated when a bright light exceeding a specific size In NIGHT ONLY mode The HLC is not activated in day light or when bright light is not present at night In NIGHT ONLY mode e When HLC function is used D ZOOM and DIS functions are not activated This function reduces the background noise in a low luminance environment 1 When the SETUP menu screen is displayed select SSNR3 by using the Function Setup switch so that the arrow indicates SSNR3 gt 6 S5HRS 2 Select a desired mode using the Function Setup switch ON Activates SSNR3 so that noise is reduced OFF Deactivates SSNR3 Noise is not reduced 3 Set the SSNR3 mode to ON and press the Function Setup switch Then you can adjust the noise reduction level e You cannot set the SSNR3 to ON or OFF when the AGC mode of the EXPOSURE menu is OFF e When adjusting the noise reduction level in the SSNR3 mode remember that the higher the level set the more the noise level will be reduced as will the brightness of the image You can display pictures in color or in black and white 1 When the SETUP menu screen is displayed select DAY NIGHT by using the Function Setup switch so that the arrow indicates DAY NIGHT gt T DAY NIGHT AUTO 2 Select a desired mode using the Function Setup switch according to the picture display you wa
9. anning angle according to the Monitoring direction You should adjust the panning angle lest that the video be displayed upside down on the monitor Adjust the Rotate position to fit the video to the screen borders Then adjust the tilting angle so that the camera faces the monitoring direction Notes e For smoother Rotate adjustment set the Tilt position between 60 80 For your easier installation you can purchase appropriate optional accessories 1 WALL MOUNT ADAPTOR SCX 300WM HANGING MOUNT SCX 300HM This adaptor is used when installing the dome camera onto a wall 2 CEILING MOUNT ADAPTOR SCX 300CM HANGING MOUNT SCX 300HM This adaptor is used when installing the dome camera on a concrete ceiling 3 POLE MOUNT ADAPTOR SCX 300PM This is an adaptor for WALL MOUNT ADAPTOR SCX 300WM installation on a pole whose diameter is bigger than 80mm 4 CORNER MOUNT ADAPTOR SCX 300KM This is an adaptor for WALL MOUNT ADAPTOR SCX 300WM installation on the corner of wall joint Connect the Video Output jack to the VIDEO IN jack of monitor CCTV Camera Monitor As the connecting method varies with the instruments refer to the manual supplied with the instrument e If necessary you can connect the monitor to the REMOTE jack on the back of your camera e Only connect the cable when the power is turned off Connect the adaptor to the power input terminal as shown in the figure below Outpu
10. del description E SCV 2080 SERIES e NTSC MODELS PAL MODELS SCV 2080N SCV 2080P m MODEL DESCRIPTION e SCV 2080X SIGNAL SYSTEM e SIGNAL SYSTEM N NTSC MODEL P PAL MODEL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL to constitute a risk of electric shock to persons The lightning flash with an arrowhead symbol within an equilateral triangle A is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to ca
11. e the dome cover 2 Lift up the inner cover while gently pressing both ends to separate it from the unit 3 Loosen 3 screws by turning them counterclockwise press both left and right lock releases inwards in arrow direction to unlock the stopper and then separate the camera from the case Inner cover Main Body Camera 1 Affix the mounting template supplied to the mounting surface 2 Drill holes diameter 5mm more than 35mm deep on the ceiling by matching to the holes on the case bed and insert plastic anchors HUD 5 fully into the holes Fix the case bed on the ceiling by using Tapping Screws TH M4xL30 4 places 3 Connect power and video cables and arrange cable running not to damage or squeeze them and assemble the camera unit in the reverse way 4 Pass the power and BNC cable through the hole you want to pass them when mounting the main body on the mounting bracket 5 Secure the camera on its mounting bracket with the four screws M4 machine screw x 3 1 Secure the mounting bracket on the place Hole for 3 4 pipe Sai anil you want to mount it after combining the IS B 0202 1966 1 Adjust the lens in a desired direction mounting bracket with the pipeline 2 Secure the inner cover to the main unit 3 Assemble the Dome Cover For waterproof purpose fix and secure the bolt using L wrench provided Case 2 Comnect power input and video output cables with the each cable from pipe
12. et White Balance first by using the ATW or AWC mode After that switch to MANUAL mode fine tune the White Balance and the Function Setup switch AWC SET To find the optimal luminance level for the current environment point the camera towards a sheet of white paper and press the Function Setup switch If the environment changes readjust it e White Balance may not work properly under the following conditions In this case select the OUTDOOR mode When the color temperature of the environment surrounding the subject is out of the control range e g clear sky or sunset When the ambient illumination of the subject is dim Ifthe camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas gt 4 550R 1 When the SETUP menu screen is displayed select SSDR by using the Function Setup switch so that the arrow indicates SSDR 2 Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas Unlike conventional cameras the SCV 2080 is designed so that it delivers a distinctive subject and background at the same time even when the subject is in bac
13. etup switch 4 Use the Function Setup switch to move to a desired letter and select the letter by pressing the Function Setup switch Repeat this to enter multiple letters You can enter up to 15 letters 5 Enter a title move the cursor to POS and press E the Function Setup switch The entered title FRONT Doge i appears on the screen Select the position to display the title on the screen by using the Function Setup switch and press the Function Setup switch When the position is determined select END and press the Function Setup switch to return to the SPECIAL menu e When the CAM TITLE menu is OFF no title will be displayed on the monitor screen even if you enter one e Only English is available in this mode If you move the cursor to CLR and press the Function Setup switch all the letters are deleted To edit a letter change the cursor to the bottom left arrow and press the Function Setup switch Move the cursor over the letter to be edited move the cursor to the letter to be inserted and then press the Function Setup switch SYNC In areas where the supply is at 60H2 NTSC 50Hz PAL frequency you can synchronize the output phase of multiple cameras using the power synchronization function Line Lock without using a synchronization signal generator INT Internal Synchronization Type L L Power Synchronization Type Line lock Press the Function Setup switch You can selec
14. he SPECIAL menu screen is displayed press the Function Setup switch so that the arrow indicates PRIVACY 2 Set up the mode using the Function Setup switch AREA You can select up to 12 PRIVACY areas MODE Determines whether to use the area selected in the AREA MASK COLOR Determine area color You can select Green Red Blue Black White Gray MASK TONE Adjust the brightness of MASK COLOR TOP BOTTOM LEFT RIGHT Adjust the size and position of the selected area RETURN Select this to save the PRIVACY menu settings and return to the SPECIAL menu DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind Notes e As the DIS function uses the digital zoom the camera s resolution will decrease DIS doesn t operate when background illumination is too low DIS doesn t operate when object pattern is monotonic as like sky or white wall LANGUAGE You can select the menu language according to your requirements NTSC Korean English French Spanish Japanese Portuguese Taiwanese PAL English Chinese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese RETURN Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu Select a desired EXIT mode using the Function Setup switch depending on the camera purpose SAVE Save the current settings
15. klight by adopting a function of the proprietary W V DSP chip 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Function Setup switch so that the arrow indicates BACKLIGHT gt 3 BACKLIGHT 2 Select a desired mode using the Function Setup switch depending on the camera purpose OFF Not being used BLC Enables a user to select a desired area on a picture and view that area more clearly LEVEL Adjusts the brightness level of a monitoring area TOP BOTTOM LEFT RIGHT Adjust the area to be enhanced HLC High Light Compensation If the scene contains extremely bright light areas such as from car headlight the light can mask out much of the on screen detail LEVEL Adjusts the brightness level of a monitoring area LIMIT Enable to change the operating condition MASK COLOR TONE Change the color brightness of the masking area Black Red Blue Cyan Magenta TOP BOTTOM LEFT RIGHT Adjust the area to be enhanced 3 Select a desired mode using the Function Setup switch O Select BLC to adjust the area to be HLC Enable the user to change the level enhanced then adjust the level limit mask color tone and area 5 172 Press SET to Return Press SET to Return Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC perform
16. line Main Body Camera na a Inner cover fa 3 Secure the main body on mounting bracket X t NA NA bd M4 machine screw x 3 Panning Tilting 1 You can adjust the camera direction only when the camera is fixed on the ceiling Then turning the camera to the left or right is referred to as Panning while moving the camera angle up or down is Tilting For panning the panning limit is 220 for the clockwise and 135 for the counter clockwise a total of 355 enabled further rotation is prevented by the stopper e Adjust the panning angle so that the camera settles in the right horizontal position You can adjust the panning up to 135 in each one direction and 220 in the other direction a total of 355 Adjust the tilting angle so that the camera settles in the right vertical position You can adjust the tilting between 0 and 90 e The total rotation range is 355 You can make adjustment in one direction up to 125 and 230 in the other direction 2 Methods of adjustment e The case of wall installation After mounting the camera on the wall adjust the panning angle so that the camera faces a desired direction when tilting Adjust the Rotate position to fit the video to the screen borders Then adjust the tilting angle so that the camera faces the monitoring direction The case of ceiling installation After mounting the camera on the ceiling adjust the p
17. lows automatic gain control from 5 3dB to 37dB O SENS UP When it is night or dark the camera automatically detects the light level and maintains a clear picture if this mode is activated OFF Deactivates the SENS UP function AUTO Activates the SENS UP function elf you set the Function Setup switch to AUTO mode You can adjust the brightness by increasing or decreasing the shutter speed x2 x512 e Note that the higher the zoom level the brighter the screen but the more likely it is that an after image will appear Although Noise Spots and Whitish symptoms may occur in SENS UP operation when the zoom level is increased this is normal RETURN Select this to save the changes in the EXPOSURE menu and return to the SETUP menu Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select WHITE BAL by using the Function Setup switch so that the arrow indicates WHITE BAL 2 Select a desired mode using the Function Setup switch gt 3 UHITE BAL x Select one of the following 5 modes as appropriate for your purpose SAW Select this when the color temperature is between 1 700 K and 11 000 K OUTDOOR Select this when the color temperature is between 1 700 K and 11 000 K sodium light inclusion INDOOR _ Select this when the color temperature is between 4 500 K and 8 500 K MANUAL Select this to fine tune White Balance manually S
18. n the screen e H REV You can flip the picture horizontally on the screen eD Z00M You can use a digital zoom of x1 x16 e FONT COLOR You can change the OSD font color White Yellow Green Red Blue e SHARPNESS As you increase this value the picture outline becomes stronger and Clearer Adjust this value appropriately depending on the sharpness of the picture e RETURN Select this to save the settings for the IMAGE ADJ menu and to return to the SPECIAL menu Notes When the V REV or H REV mode is enabled the text on the screen does not flip e If you increase the SHARPNESS level too high the picture may become distorted or noise may appear Monitor Please change the settings value of video appropriate to your monitor LCD Please select this menu item when using an LCD monitor You can change the gamma PED level and color gain in the sub menus CRT Please select this menu item when using a CRT ft Eu monitor You can change the PED level color LCD MONITOR gain in the sub menus USER Please use this menu item when using a monitor other than standard ones You can change the gamma PED level and color gain in the sub menus CAM TITLE If you enter a title the title will appear on the monitor 1 If the SPECIAL menu screen is displayed use the Function Setup switch so that the arrow indicates CAM TITLE 2 Set it to ON by using the Function Setup switch 3 Press the Function S
19. ng of WHITE BAL SETUP menu The screen flickers continually gt Ensure the camera is not pointing towards the sun When coaxial communication is not available gt Make sure that the camera and monitor are installed within the recommended distance gt Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded The camera is out of focus Check that you have properly adjusted the zoom focus adjustment lever of lens Power Consumption Imaging Device agonal 6mm Super Total Pixels 811 H x 5080 795 H x 596 Effective Pixels 768 H x 494 V 752 H x 582 Scanning System 2 1 Interlace Synchronization Internal Line Lock Frequency H 15 734KHz V 59 94Hz H 15 625KHz V 50 00Hz Horizontal Resolution COLOR 600TVL B W 700TVL Min Illumination COLOR 0 15 Lux SOIRE F1 2 0 0003Lux SENS UP x512 BAW 0 001Lux SOIRE F1 2 0 000002Lux SENS UP x512 SIN Y Signal 52dB Weight On AGC Off Video Output CVBS 1 0Vp p 759 composite Pan Tit Rotate Range ON Screen Display NTSC Korean English Japanese Spanish French Portuguese Taiwanese PAL English Chinese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese SSDR On Off Level adjustable Backlight Compensation BLC HLC OFF Day 8 Night CO
20. ngs mode You can adjust the shutter value of ESC shutter mode gt 1 LEHS DE b gt 2 EMPOSURE I 1 When the SETUP menu screen is displayed select EXPOSURE by using the Function Setup switch so that the arrow indicates EXPOSURE 2 Select a desired mode using the Function Setup switch BRIGHTNESS Adjusts the video brightness SHUTTER You can select the shutter oo Shutter speed is fixed at 1 60 sec 1 50 sec ESC Select this to control the shutter speed automatically If ESC is selected the shutter speed is automatically controlled depending on the ambient illumination of the subject MANUAL You can control shutter speed manually NTSC MODEL 1 60sec 1 120 000sec PAL MODEL 1 50sec 1 120 000sec AFLK Select this when you experience picture flicker this happen when there is a clash with the installed lighting frequency Set the shutter mode to if color rolling occurs e When the SHUTTER is set to ESC after selecting the Internal Synchronization Type the picture may become unstable if the camera faces a bright fluorescent light Therefore take care when choosing the installation position e When the SHUTTER is set to MANUAL or A FLK mode SENS UP will be disabled AGC AUTO GAIN CONTROL The higher the gain level the brighter the screen but the greater the noise OFF Deactivates the AGC function LOW Allows automatic gain control from 5 3dB to 32dB HIGH Al
21. nt AUTO The mode is switched to Color in a normal environment but switches to B W mode when ambient illumination is low To set up the switching time for AUTO mode press the Function Setup switch You can turn on or off the burst signal on BW mode BURST MODE You can tum on or off the burst signal on B W mode DURATION You can select the day night switching point DWELL TIME You can select day night switching delay time from 3s 5s 7s 10s 15s 20s 30s 40s 60s Color gt B W B W gt Color Early 2 5 lux 5 lux Late 1 lux 10 lux The day night switching point of the camera can be adjusted COLOR The picture is always displayed in color SBM _ The picture is always displayed in black and white You can tum on or off the burst signal on BAW mode Notes e When AGC in the EXPOSURE menu is OFF mode operates as selecting COLOR mode and AUTO mode cannot be selected 1 When the SETUP meru screen is displayed select SPECIAL by using the Function Setup switch so that the arrow indicates SPECIAL gt 3 SPECIAL 2 Select a desired mode using the Function Setup switch 1 IMAGE ADJ IMAGE ADJ 1 When the SPECIAL menu screen is displayed select IMAGE ADJ by using the Function Setup switch so that the arrow indicates IMAGE ADJ 2 Select a desired mode using the Function Setup switch eV REV You can flip the picture vertically o
22. t a desired phase from 0 to 359 when select phase Press SET to Return e When using AC power at 60Hz NTSC 50Hz PAL frequency you can use the L L type synchronization When the power is DC 12V the SYNC menu is fixed to the INT mode O MOTION DET This product has a feature that allows you to observe Movement of objects in 8 different areas on the screen and the words MOTION DETECTED appear on the screen when movement is detected You can Monitor activity more efficient 1 When the SPECIAL menu screen is displayed press the Function Setup switch so that the arrow indicates MOTION DET 2 Set up the mode using the Function Setup switch SENSITIVITY You can select up to 8 MD areas When SENSITIVITY number is high motion detection sensitivity is increased to recognize even small movement AREA MODE Determines whether to use the MD area selected in SENSITIVITY SEL POS Determines which of the 4 vertices of each MD area is to be used XPOS Determines the coordinate of the horizontal axis for SEL POS YPOS Determines the coordinate of the vertical axis for SEL POS FILL SET Fills in a selected MD area The color of filling is sequentially selected as brown orange blue cyan green yellow magenta and red RETURN Select this to save the MOTION DET menu settings and return to the SPECIAL menu PRIVACY Mask an area you want to hide on the screen AREAL 1 When t
23. t for surveillance systems Therefore we can t compensate for material loss and or personal injuries by robbery fire natural disaster or other such events Warning Attention Special Mark Messages Ignoring this information may pA 5 Ignoring this information ma result in material loss and or gorg 5 y RENE 4 result in material loss and or a serious personal injuries including death slight injuries Indicates Never Allowed Indicates No Disassembling Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems a This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal COLOR DOME CAMERA D SCV 2080
24. t of the adaptor should be either one of AC 24 V 1 5 Aor DC 12 V 1 0 A Note that using DC 12 V may cause lower heater temperature Power Input Terminal As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera There may be some deviation in voltage drop depending on the type of wire and the manufacturer Be sure to connect power only after all the installation is complete e Note that AC DC adaptor is not supplied with camera e Ground should be connected to the GND terminal e Coaxial Communications System e OSD Control method OSD KEY JOYSTICK UP JOYSTICK DOWN JOYSTICK LEFT JOYSTICK RIGHT e Video Cable e BNC e RS 485 The camera s video output port is connected to the monitor with a BNC coaxial cable shown below If the distance between the camera and the monitor exceeds the recommended maximum please use an auxiliary video amp e DC BRIGHTNESS SENS UP SHUTTER AGC RETURN ATW MANUAL OUTDOOR INDOOR AWC gt SET 0FF ON OFF BLC OFF ON COLOR B W IMAGE ADJ SYNC DIS MONITOR MOTION DET LANGUAGE SAVE NOT SAVE Distance Recommended Cable Specification 300m 3C2V RG 59 U
25. to the above Directive s Manufacturer SAMSUNG TECHWIN CO LTD Legal Representative in Europe Signature BI Au Signature Full Name BONJENG GU Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON KOREA Place Date 2010 03 01 Date SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD Samsungtechwin R amp D Center 701 Sampyeong dong Bundang gu Seongnam si Gyeonggi do Korea 463 400 TEL 82 70 7147 8740 60 FAX 82 31 8018 3745 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Park Tol Free 1 877 213 1222 FAX 1 310 632 2195 Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungsecurity com P No Z6806 1233 01A
26. use harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes Contents e Features 6 e Precautions 8 e Components and Accessories sssssesssssssseneressesuuneusonsossussuuneaesoss 10 e Overview e Installation E Installation E Adjusting the monitoring direction of the camera E Optional Accessories for Installation e Connection E Connecting to Monitor E Connecting to Power E Using Coaxial Communications een 20 Operating Your Camera E Menu Configuration E Menu Setup LENS EXPOSURE mmm WHITE BAL White Balance SSDR Samsung Super Dynamic Range BACKLIGHT Troubleshooting e Specifications 11711711 o DIMENSION sssssessssesssrssersessusasnsrosesesesnsosusnssessessnsessvsoserseesnsesevssse COLOR DOME CAMERA 5 SCV 2080 Features IP66 Approved Dust and Rain Resistant With dust and rain resistant design the camera can be installed outside under building eaves or places that are exposed
Download Pdf Manuals
Related Search