Saeco Saeco HD8753/81 coffee maker
Contents
1. The INTENZA water filter can improve the quality of water Using the INTENZA filter will prevent limescale from building up and will ensure a much more intense aroma to your espresso coffee We therefore recom mend you install the INTENZA water filter which can be purchased from your local dealer or on line at the Philips on line store http shop philips com or at authorized service centres INTENZA Water Filter Installation E Remove the small white filter from the tank and store it in a dry place sheltered from dust Remove the INTENZA water filter from its packaging immerse it vertically with the opening positioned upwards in cold water and delicately press the sides so as to let the air bubbles out Measuring water hardness is very important in order to correctly manage the INTENZA water filter and the frequency with which the machine must be descaled EJ the filter should be set according to the measurements performed to set the water hardness Use the water hardness test strip provided with the machine Set the Intenza Aroma System as specified on the filter packaging see section Measuring Water Hardness A Soft water B Hard water standard C Very hard water El put the filter into the empty tank Press it until its limit stop 5 E Fill the tank with fresh drinking water and reinsert it into the machine 6 Dispense the water in the tank by using the hot wat2. EM immerse the water hardness test strip provided with the machine in Y water for 1 second Note The test strip is only valid for one measurement Nim E Check how many squares change colour and refer to the table Note The letters correspond to the references that are located in the base of the INTENZA filter The filter must be adjusted according to this measurement Intenza Aroma System 2 Machine water hardness setting Orange Orange Green EJ The numbers correspond to the settings that are found for the water hardness adjustment shown in the programming chapter More precisely 1 1 very soft water 2 2 soft water 3 3 hard water 4 4 very hard water El once you know this value set the water hardness value Press the taw button and scroll the pages by pressing the o but ton until the following page is displayed g Note The machine is supplied with a standard adjustment suitable for most of the uses A Press The button to increase the value or the button to reduce the value Tl Press the ves button to confirm the adjustment Press the nly button to exit and brew the products ENGLISH 15 Espresso Coffee Brewing and Adjustments The machine you have bought works with coffee beans and or pre ground coffee It allows for certain adjustments that will permit you to use it to its full potential and get a complete Espres
3. and under the milk dispenser Zl Press the button The following icon is displayed SPECIAL E Press the button to start hot milk dispensing A al The following icon is displayed during the preheating time required by i z the machine lt fo STOP Once the warm up phase is complete the machine starts dispensing water to be used for cleaning Green a EJ When all the water has been dispensed repeat the operations from point 4 until the solution in the carafe has been poured off Drinking the solution dispensed during this procedure is strictly forbidden The solution must be disposed of EJ Remove the carafe from the machine and the container utilized to col lect the solution STOP Orange Green Green ENGLISH 35 EQ Wash the carafe thoroughly and fill it with fresh drinking water that will be used for rinsing EE Insert the carafe with the rinsing water into the machine and place a container under the coffee dispensing spout and under the milk dispenser Press the ea button The following icon is displayed GE Press the button to start hot milk dispensing EE The following icon is displayed during the preheating time required by the machine IH Once the warm up phase is off the machine starts dispensing water to be used for rinsing EJ When all the water has been dispensed repeat the operations from point 12
4. height of the dispensing spout may be adjusted to better fit the dimensions of the cups that you wish to use Manually move the dispensing spout up or down to adjust its height by placing your fingers as shown in the figure The recommended positions are For the use of small cups For the use of large cups Two cups can be placed under the dispensing spout to brew two cups of coffee at the same time 18 ENGLISH Using Coffee Beans To brew a cup of Espresso coffee press and release E The 2 button to select the desired Aroma The button for a cup of espresso or the button for a cup of long espresso MEMO 5 The brewing cycle will start g To brew 1 cup of coffee press the button once This icon will be dis played To brew 2 cups of coffee press the button twice consecutively This o icon will be displayed oO Note To brew 2 cups of coffee the machine automatically grinds and doses the correct amount of coffee Brewing two coffees requires two grinding cycles and two brewing cycles which the machine carries out automatically EJ Once the prebrewing cycle is complete coffee begins to come out of the dispensing spout Ef The coffee brewing process stops automatically It is nevertheless possible to interrupt the coffee brewing process by pressing the 2 STOP button Using Pre ground Coffee This function allows using pre ground and decaffeinated coffee P
5. stored in the refrigerator and poured into the carafe only when preparing a beverage with milk After use put the carafe back in the refrigerator DO NOT leave the milk out of the refrigerator for more than 15 minutes Note The milk container must be filled with milk at refrigerator temperature Warning It is forbidden to use the container for any other liquids other than drinking water Note Clean the dispensing spout with a cloth after each use to avoid that milk residues can be poured after the dispensing cycle Filling the Milk Carafe The milk carafe may be filled before the use or if necessary also during use To fill the carafe proceed as follows El Lift the top lid of the carafe Pour the milk The level of milk poured into the carafe must be be tween the MIN level and the MAX level Thereafter the container may be used to brew the desired beverages ENGLISH 21 Inserting the Milk Carafe In order to be used the milk carafe must be inserted into the machine In order to insert the carafe proceed as follows E Remove the water dispenser if supplied Press the dispenser on the sides to unlock it and lift it slightly Extract the dispenser Open the milk carafe dispenser by turning it counter clockwise until it locks into place EJ Bring the carafe closer by keeping it slightly tilted The front part must be inserted into the guides present in the machine E Insert the carafe all t
6. the Dispensing Spout Using Coffee Beans Using Pre ground Coffee Adjusting the Coffee Length MEMO Function Milk Carafe Filling the Milk Carafe Inserting the Milk Carafe Removing the Milk Carafe Emptying the Milk Carafe CAPPUCCINO scsssssscscsscesscsssecececsees Adjusting the Cappuccino Length MEMO Function Hot Water Dispensing Eco friendly Stand by Stand by Cleaning and Maintenance General Cleaning ssssseseee Cleaning the Milk Carafe After Each Use Weekly Cleaning of the Carafe Carafe Lid Monthly Cleaning of the Carafe thorough Cleaning Brew Group 00000 Weekly Cleaning Brew Grou Brew Group Cleaning with Coffee Clean Tablets Brew Group Lubrication Descaling Programming Enter the Menu Programming Controls Exiting the Programming Mode FUNCTIONS oo sssssssssssssee Programming Example Control Panel Display Adjusting the Amount of Hot Milk in the Cup MEMO Function Troubleshooting ccccccssssssssesssesssesssesssessseessesssessseessesssesessssessesseseserers Technical Specifications AI AT E PETE EAE E EOT ES 4 ENGLISH Introduction Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome In this user manual you will find all the informati
7. 90 toll free Brazil 0800 701 0203 other areas 11 2121 0203 San Paolo Bulgaria 00 800 11 544 24 toll free Canada Montreal 1 514 385 5551 Toronto 1 416 256 9191 Vancouver 1 604 299 7555 Czech Republic 800 142840 China 4008 800 008 Croatia 0800 222 778 Denmark 3525 8759 Germany 0800 000 7520 toll free Spain 902 199 742 Estonia 8000100288 France 0805025510 toll free Greece 0 0800 3122 1280 toll free Hong Kong 852 2619 9663 Israel 03 6458844 Iran 98 21 2227 9353 Ireland 18007445477 toll free Italy 800 233 793 toll free Korea 080 600 6600 toll free Kuwait 1 80 35 35 Latvia 80002794 Lebanon 961 1 684900 Lithuania 880030483 Luxembourg 0800 26 550 Hungary 06 80 018 189 Malaysia 1800 880 180 The Netherlands 0800 023 0076 toll free Norway 2270 8111 Austria 0800 180 016 toll free Poland 00800 3111318 Portugal 800 780 903 toll free Romania 0800 894910 available for free from the Romtelecom network Russia 7 495 961 1111 8 800 200 0880 Singapore 65 68823999 Slovenia 080080254 Slovak Republic 0800 004537 toll free Finland 09 2311 3415 South Africa 08611 72326 Sweden 0857929100 Switzerland 0800 002 050 toll free Ukraine 0 800 500 697 United Arab Emirates Dubai 971 4 2310300 United Kingdom 08003316015 toll free USA 800 933 7876 toll free Taiwan 0800 231099 Thailand 6626528652 PHILIPS The man
8. Brew Group section Clean the dispensing spout and its holes Note These problems can be considered normal if the coffee blend has been changed or the machine is being installed for the first time In this case wait until the machine performs a self adjusting operation as described in section Saeco Adapting System Please contact our consumer care help line at the phone number listed at the last page of this document for any problems not covered in the above table or when the suggested solutions do not solve the problem Technical Specifications The manufacturer reserves the right to make changes to the technical specifications of the product Nominal voltage Power rating Power supply 2 ceceeee eee e eect ee ee eee eneeeeeeeeeneeneeee See label on the inside of the service door Housing material Thermoplastic material Siz WX 1K MM rierien a ENEA AREE PEAN EE AA EAA TEA RETE RANES 256 x 340 x 440 T I AAA EE EE ES EA 9kg Power cord length xs cccsdavvavewivisess daa EEEE ER EEEE EA RAAEN EERE EN EEEE E 1 2m Controlpanel seende EE E EAEE EALES E TOTE O E A T E O O OEE On the front CAPPUCCINI LOTE S Ea EESE NERE ENEAS EAEE EEE NENEK OE sive NEEN NEE AE ENEE Special for cappuccino Water tank lt icsc3cnsccevadvees saeaeans 1 5 litres Removable type Coffee bean lhoppercapacity O iiris noriai Vannes EEE EEEE ETENEE be salmaaa heweige E ANE EE A 300 Coffee qrounds drawer apad tYiznese anan ENE ES EEEE E
9. EOAE NESE EAEE ENEN EEAS 10 P MPPrESSUE arean arsena rera r EE EEN EEA E NENEA EAE E EA T EA EAEE TO EAA 15 bar Boiler Stainless steel type Safety MOVIES aasi EEE rE EESE NEN EE ENEE NEEE RE OEE TEO EATE E EEEE NEET EEE EEDEN E aces Thermal fuse In compliance with art 13 of the Italian Legislative Decree dated 25 July 2005 no 151 Implementation of the Directives 2002 95 EC 2002 96 EC and 2003 108 EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment as well as waste disposal L The symbol of the crossed out wheeled bin mmm on the appliance or its packaging indicates that the product must be disposed of separately from other waste at the end of its operational life The user must therefore take the appliance to be disposed of to an appro priate separate collection centre for electronic and electro technical equipment or take it to the dealer when buying a new appliance of the equivalent kind one by one Appropriate separate collection for the dismantled appliance being subsequently sent out for recycling treatment and for environmentally friendly disposal contributes to the prevention of possible negative effects on the environment and on human health and encourages re employment and or recycling of the materials the appliance is made of Specific administrative sanctions provided for by current regulations will be applied for illicit disposal of the product by the user We want to ens
10. Register your product and get support at www philips com welcome INTELIA Type HD8753 OPERATING INSTRUCTIONS READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE PHILIPS CE Saeco English IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 2 3 8 9 Read all instructions Do not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surtaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord into wall outlet To disconnect turn any co
11. ate also the shaft ENGLISH 41 EJ Insert the Brew Group in its seat again until it locks into place WITHOUT pressing the PUSH button Note the detailed instructions to prepare the brew group and insert it correctly in the machine can be found on page 37 point 7 8 9 and 10 of the section Brew Group Weekly Cleaning E insert the coffee grounds drawer Close the service door Descaling Limescale is a natural part of the water used for the machine operation It needs to be removed regularly as it may clog the water and coffee circuit of your appliance This is an easy procedure with your Philips Saeco machine The advanced electronics tells you on the display of the machine in clear symbols when descaling is needed Just follow the steps described below Not doing this will ultimately make your appliance stop working properly and in this case repair is not covered under your warranty Note Empty the drip tray before performing the descaling cycle Use the Saeco descaling product only Its formula has been designed to ensure better machine performance and operation for its whole operating life If correctly used it also avoids alterations in the brewed product The descaling solution and the complete Maintenance Kit may be purchased at your local dealer at the Philips on line shop at http shop philips com or at authorised service centres Warning Never drink the descaling solution or any products d
12. cribed in the Cleaning and Maintenance chapter Adjusting the Cappuccino Length MEMO Function The machine allows you to adjust the amount of cappuccino brewed ac cording to your taste and or the size of your cups Each time the amp button is pressed and released the machine pours a pre set amount of cappuccino This amount may be set again according to your taste El Prepare the machine to brew a cappuccino Place the desired cup under the dispensing spout EJ Press and hold the button until the MEMO icon is displayed CAPPUCCINO and remove your finger The machine is now programming E1 The following icon is displayed during the preheating time required by the machine E The machine begins dispensing the milk The display shows the STOP symbol u e MEMO Press the button when the desired amount of milk is reached in the cup Green ENGLISH 25 Fal After milk dispensing the machine begins the coffee brewing phase The STOP message is displayed Press the button when the desired amount of coffee is reached in the cup Now the button has been programmed each time it is pressed and CAPPUCCINO released the machine will brew the same amount that has just been set Green Orange Green Dispensing may be preceded by short sprays of milk and steam Risk of scalding Wait for the end of the cycle be
13. der Taste for light roasted coffee blends Aroma Adjustment Select Your Favourite Amount Choose your favourite coffee blend and adjust the amount of coffee to be ground until they meet your personal taste The machine is set up to adjust the amount according to the coffee to be ground Four choices are possible by pressing and releasing the we button Mild medium or strong aroma and pre ground coffee Selection can be made when the beans appear on the display Each time the EA button is pressed and released the aroma changes by one degree according to the selected amount 2 Mild aroma Medium aroma Strong aroma Note Selection must be made prior to select coffee The system sets the aroma according to the personal taste of the user After selecting Strong aroma the function for brewing coffee with pre ground coffee is displayed This selection is displayed by the icon on the side Refer to the relevant section to use this function ENGLISH 17 Brewing Coffee Note Should the machine not brew coffee make sure that the water tank contains water Before brewing coffee check the lights on the display and make sure the water tank and coffee bean hopper are full Before brewing coffee adjust the height of the dispensing spout according to your needs and select the aroma or pre ground coffee Adjusting the Dispensing Spout Most cups on the market can be used with this coffee machine The
14. e contrast of the display to better view the messages Display contrast Orange Water Hardness This function allows you to adjust water hardness to better manage ma chine maintenance 1 very soft water 2 soft water 3 hard water 4 very hard water Orange For more details please see the Measuring Water Hardness section INTENZA Water Filter This function allows you to manage the INTENZA water filter For more details see the section related to filter handling Orange START ESG Descaling Cycle This function allows you to run the descaling cycle Orange Factory Settings ete This function allows you to reset all factory values bo q SETTING d Orange Programming Example In this example we want to explain how to programme the display con trast Proceed in a similar manner to change the other functions The programming menu can only be accessed when the machine is in on amp Press the W button to access programming Display contrast d ESC Display contrast OK ESC Display contrast Orange Orange Orange Orange ENGLISH 47 The first page is displayed Press the button until the CONTRAST function is displayed Press the button once to increase the contrast MEMO Press the 8 button to confirm Press the q button to exit pro
15. ect Espresso Rinse the coffee circuit if using the machine for the first time or after a long period of inactivity Besides the rinse self cleaning cycle we recommend you to run these simple operations to always brew excellent espresso They have to be performed A At first start up B When the machine remains inactive for a long time more than 2 weeks Ell Piace a large container under the dispensing spout Before starting the procedure check that the following icon is dis played Select the pre ground coffee brewing function by pressing the ver button one or more times until the following icon is displayed Note Do not add pre ground coffee into the compartment Green ENGLISH 11 EJ Press the button Wait until the dispensing procedure is complete MEMO and empty the water tank 4 Repeat the operations from step 1 to step 3 for 3 times then continue with step 5 H Place a container under the water dispensing spout Fal Press the button The following icon is displayed SPECIAL Press the D button to start dispensing hot water Dispense water until the no water signal appears EJ At the end fill the water tank again Then the products can be brewed as described in the following sections Note If available it is necessary to install a new Intenza filter in the ma chine as described in the following section 12 ENGLISH INTENZA Water Filter Optional
16. ee grounds drawer Empty the coffee grounds drawer and the liquid recov ery tray Fill the water tank Insert the drip tray all the way 50 ENGLISH Troubleshooting For the most common issues please refer to the table below or to the FAQ section on www philips com support for the latest updates This will help Machine actions The machine does not switch on Coffee is not hot enough No hot water is dispensed Coffee has not enough crema See note The milk was not frothed The machine takes a long time to warm up or the amount of water dispensed from the wand is too little The Brew Group cannot be removed The machine grinds the coffee beans but no coffee comes out See note Coffee is too weak See note Coffee is brewed slowly See note Coffee leaks out of the dispensing spout you identify the appropriate action Causes The machine is not connected to the electric network Solutions Connect the machine to the electric net work The power button is on position 0 The cups are cold The hot water dispensing spout orifice is clogged The blend is unsuitable coffee is not freshly roasted or the grind is too coarse The Carafe is dirty or not inserted correctly The machine circuit is clogged by limescale The Brew Group is out of place Check that the power button is set to I Preheat the cups with hot water Unclog the orifice of the hot water dispensing sp
17. er function see section Hot Water Dispensing TAS Rar N EA Fiii the water tank again APA A ESC ENGLISH 13 EJ Press the button and scroll the pages by pressing the az but Y ON E5 2 ton until the following page is displayed POTI E 5 r ESC gy EJ Press the button to select ON and press the e button to WATER D MEMO PONA yFILTER c confirm OFF EJ fw k O In this way the machine has been programmed to inform the user of the need to replace the filter ESC S Note When an INTENZA water filter must be replaced with a new one the ON ae 2 function must be reset Replace the filter as previously shown pean EJ 5 After that enter the programming menu until the indicated page is displayed and select the RESET option Then press the 0 button The machine is now programmed to manage a new filter 5 ESC 3 Note If the filter is already installed and you want to remove but not replace ON JFT D it select the OFF option and then press the button POFA r To exit press the ly button until the home page is displayed vo LP 92 8 6 Note If there is no INTENZA water filter insert the small white filter previ ously removed into the water tank Measuring Water Hardness Measuring water hardness is very important in order to correctly manage the INTENZA filter and the frequency with which the machine must be descaled
18. essing the same button again nn MEMO Only after adding the descaling solution in the tank press the button to start the descaling cycle EJ At this point the machine will start dispensing the descaling solution at intervals the bar shows the cycle progress START Red Red Red Red Red Red ENGLISH 43 Note The descaling cycle may be paused by pressing the button To re sume the cycle press the button again This allows you to empty the container or to go away for a short period of time EJ When the solution in the tank is finished the icon on the side is dis played The icon indicates that the tank must be rinsed and filled I Rinse the water tank thoroughly and refill it with fresh drinking water EK Empty the container used to collect the liquid dispensed by the ma chine and place it back under the dispensing spout When inserting the tank filled with water the icon on the side is dis played GE Press the button to start the rinse cycle of the machine e Note The rinse cycle may be paused by pressing the button To resume the cycle press the button again This allows you to empty the container or to go away for a short period of time EE When the water in the tank is finished the icon on the side is displayed to indicate that the tank must be rinsed and filled with fresh drinking water to finish t
19. fore removing the container Refer to the section Milk Carafe E Fil the milk carafe with the desired quantity Note To ensure better results when preparing a hot milk use cold milk BA Open the milk dispenser and insert the milk carafe into the machine EJ Place the cup for hot milk under the carafe dispenser Note Ensure that the cup is positioned correctly under the dispenser to avoid spilling the product El Press the 2 button The following icon is displayed SPECIAL E Press the button to start hot milk dispensing KA The following icon is displayed during the preheating time required by the machine The machine pours a preset quantity of hot milk into the cup The pouring may be stopped early by pressing the button After using the milk carafe to prepare the desired milk wash it as described in the Cleaning and Maintenance chapter 26 ENGLISH Adjusting the Amount of Hot Milk in the Cup MEMO Function The machine allows you to adjust the amount of dispensed hot milk ac cording to your taste and or the size of your cups Every time this function is selected the machine dispenses the preset amount of hot milk This amount may be set again according to your taste El Prepare the machine to dispense hot milk FJ Place the desired cup under the dispensing spout EJ Press the button The following icon is displayed SPECIAL Green E Press and hold the button until t
20. gramming The function is now programmed 48 ENGLISH Control Panel Display This appliance is equipped with a colour coded system to make the user s understanding of the display signals easier For maximum convenience the icons are colour coded according to the traffic light principle The display colour coded interface combined with buttons directly for wards the key operating messages in a simple and easy way Ready Signals green colour LP z LP gt gt r ESC Sa STOP STOP STOP The machine is ready to brew coffee from coffee beans and to dispense hot water The machine is ready for pre ground coffee brewing Hot water or hot milk selection Hot water dispensing Dispense hot milk Milk dispensing phase during cappuccino preparation Coffee dispensing phase during cappuccino preparation STOP MEMO STOP MEMO STOP The machine is brewing 1 cup of espresso coffee The machine is brewing 1 cup of coffee The machine is brewing 2 cups of espresso coffee The machine is brewing 2 cups of coffee The machine is program ming the amount of coffee to be brewed The machine is program ming the amount of milk to dispense for the cappuccino The machine is program ming the amount of coffee to dispense for the cappuc cino The machine i
21. he MEMO icon is displayed and remove your finger The machine is now programming E The following icon is displayed during the preheating time required by the machine Orange Fal The machine begins dispensing the milk The display shows the STOP g symbol v gt Press the button when the desired amount of milk is reached in the cup Now the amount of hot milk has been programmed each time the button is pressed and released the machine will dispense the same amount that has just been set Green ENGLISH 27 Hot Water Dispensing Before dispensing hot water check that the machine is ready to use and the following icon is displayed When the machine is ready to brew coffee proceed as follows El insert the hot water dispenser Approach the dispenser by keeping it slightly tilted It must be inserted all the way into the guides in the machine Insert the hot water dispenser with a combined rotation pushing motion towards the bottom as indicated in the figure until it locks into place Place a container under the hot water dispensing spout EJ Press the amp button The following icon is displayed SPECIAL EJ Press the button to start dispensing hot water 28 ENGLISH STOP l Yp Green Orange E Pour the desired amount of hot water To stop the hot water dispens ing pre
22. he cycle IE Empty the container used to collect the liquid dispensed by the ma chine and place it under the dispensing spout Wd When inserting the tank filled with water the icon on the side is dis played Press the button to start the rinse cycle of the machine MEMO 44 ENGLISH The machine performs the rinse cycle with a pre set amount of water The machine may require to refill the tank many times if the necessary amount of water has not been reached The following icon indicates that the tank needs to be refilled Once the tank has been inserted restart the cycle by pressing the ee button Ed When the amount of water needed for the rinse cycle has been completely dispensed or the water tank has been inserted again in the machine the icon on the side is displayed Press the ue button to quit the descaling cycle Red The machine now carries out the warm up and rinse cycle to prepare for product brewing The descaling cycle is complete Note The descaling solution must be disposed of according to the manufac turer s instructions and or regulations in force in the country of use Note After completing the descaling cycle wash the brew group as described in the Brew Group section in the Cleaning and Maintenance chapter After completing the descaling cycle Remove the milk carafe and clean it as described in the section Weekly Cleaning of the Carafe Empty the drip tray To
23. he way into the guides E Insert the carafe with a combined rotation pushing motion towards the bottom as indicated in the figure until locking the insert at the drip tray Do not force the inclination of the carafe more than intended 22 ENGLISH Removing the Milk Carafe The following operations show how to properly remove the carafe from the machine Do not force the inclination of the carafe more than intended El Rotate the carafe upwards until it releases from the insert in the drip tray Keep pulling until it is completely detached After the use remove the container from the machine and place it in the refrig erator for proper conservation We recommend NOT to keep the container at room temperature for too long Maximum 15 minutes Store the milk according to producer s instructions and do NOT use it after best before date Wash the container as described in the MILK CARAFE CLEAN ING section see page 31 Emptying the Milk Carafe The operations illustrate how to empty the milk contained inside the carafe El Press the release buttons to allow the lid removal Lift the lid now the milk contained inside may be emptied ENGLISH 23 Dispensing may be preceded by short sprays of milk and steam Risk of scalding Wait for the end of the cycle before removing the container Refer to the section Milk Carafe E Fil the milk carafe with the desired quantity Note To ensure better results when
24. ical household appliances Do not leave the machine packaging materials within the reach of children Danger of Burns Never direct the jet of hot steam and or hot water towards yourself or oth ers Danger of scalding Always use the handles or knobs provided 6 ENGLISH Machine Location Suitable Location for Operation and Mainte nance For best use it is recommended to 150mm 6 inches s 2 wae mm ee a 6 inches Choose a safe level surface where there will be no danger of overtur ning the appliance or being injured Choose a location that is sufficiently well lit clean and near an easily reachable socket Provide for a minimum distance from the sides of the machine as shown in the illustration While switching on or off the machine we suggest placing an empty glass under the dispensing spout Do not keep the machine at temperatures below 0 C Frost may damage enches ALA n the machine Do not use the coffee machine outdoors N A 6inches K 6inches C In order to prevent its housing from melting or being damaged do not place the machine on very hot surfaces and close to open flames leaning and Storing the Machine Keep the machine at its best clean and store it properly Since the machine uses natural ingredients to brew beverages coffee beans water milk etc some residues of ground coffee or condensed wa ter could be present on its supporting surface For this reason we recom mend to
25. ispensed until the cycle has been carried out to the end Never use vinegar as a descaling solution El Turn on the machine by pressing the button Wait for the machine to finish its rinse and warm up process Warning Remove the Intenza filter before adding the descaling solution Note Before descaling perform the following operations Empty the drip tray Insert the empty milk carafe see Dispensing Milk 42 ENGLISH OK ae bescaver lls E Orange Red Red Press the qq button and if necessary scroll the pages by pressing the button until the following page is displayed EJ Press the button to enter the descaling menu n mewo Note If you press the button by mistake press the D to quit If the button is pressed the descaling cycle starts and it is necessary to complete it before brewing coffee EJ Pour the entire content of Saeco concentrated descaling solution into the appliance water tank E Fill with fresh drinking water up to the MAX level Place the tank back in the machine K Place an empty container under the coffee dispensing spout and under the milk dispenser Note Use a container of at least 1 5 litre capacity If you do not have a con tainer of this capacity pause the cycle by pressing the button empty the container place it under the dispensing spout and restart the cycle by pr
26. ly make your appliance stop working properly and in this case repair is not covered under your warranty General Cleanin E Empty and clean the coffee grounds drawer daily with the machine turned on Note Other maintenance and cleaning operations can only be carried out when the machine is cold and disconnected from the electrical network Do not immerse the machine in water Do not wash any of its parts in the dishwasher Do not use sharp objects or harsh chemical products solvents for cleaning Use a soft dampened cloth to clean the machine Do not dry the machine and or its parts using a microwave and or stand ard oven Empty and clean the drip tray daily Perform this operation also when the float is raised Press the release buttons to allow tray removal Remove the drip tray Note When inserting the tray ensure it is locked properly into the machine to avoid any malfunctions 30 ENGLISH EJ It is recommended to clean the water tank daily Remove the INTENZA water filter or remove the small white filter if you have not yet installed the INTENZA water filter from the water tank and wash it under running drinking water Reposition the INTENZA water filter or the small white filter if you have not yet installed the INTENZA water filter in its hous ing by gently pressing and turning it at the same time Fill the water tank with fresh drinking water EJ When emptying
27. maining water Note Refer to the following section for a thorough cleaning Weekly Cleaning of the Carafe Carafe Lid When used the milk carafe lid must be cleaned in depth once a week To clean the carafe proceed as follows El Press the release buttons to remove the lid Turn the milk dispenser until it reaches the mark and remove the dispenser from the lid ENGLISH 33 EJ Press on the bottom to remove the dispenser E Slide the milk frothing device upwards EJ Pulling the fitting outwards Fal Remove the suction tube Wash all the components with lukewarm water Note After washing all the components reassemble the parts on the lid follow ing the same procedure used for disassembly but in reverse order Important note As highlighted at point 2 the dispenser can be inserted in the lid only when it is in the position 34 ENGLISH Monthly Cleaning of the Carafe thorough Cleaning Clogging Power Perform a thorough cleaning of all the Cappuccinatore parts every month using the Saeco detergent that can be purchased at your local dealer or at the Philips on line shop at http shop philips com or at the authorised service centres EJ Fill the carafe with fresh drinking water up to the MAX level Pour a solution bag in the water you have just prepared and let it dis solve completely EJ Insert the carafe into the machine and place an empty container under the coffee dispensing spout
28. n the appliance and wait until the rinse cycle is complete Green ENGLISH 39 EJ Remove the coffee residues drawer and then the Brew Group EJ Wash the Brew Group thoroughly with clean water ter rinsing the Brew Group insert it again in its seat until it locks into E af h B G il l k place WITHOUT pressing the PUSH button Insert the coffee residues drawer Gl Press and release the Z button one or more times to activate the pre ground coffee function without adding any coffee to the compart ment Start the coffee brewing cycle pressing the button MEMO EE Repeat the operation twice from step 11 to step 12 Make sure you discard the dispensed water EE To clean the drip tray place a tablet inside and fill it up to 2 3rds with hot water Let the cleaning solution take effect for about 30 minutes then rinse thoroughly 40 ENGLISH Brew Group Lubrication Lubricate the Brew Group after approximately 500 cups of coffee or once a month The grease to lubricate the Brew Group and the complete Service Kit may be purchased at your local dealer at the Philips on line shop at http shop philips com or at authorised service centres Before lubricating the brew group clean it under running water as described in the Weekly Cleaning Brew Group section El Lubricate the brew group guides using the Saeco grease only Apply the grease evenly on both side guides Lubric
29. ng the PUSH button E Insert the clean coffee residues drawer Gi Insert the coffee grounds drawer Close the service door 38 ENGLISH Brew Group Cleaning with Coffee Clean Tablets 4 Besides weekly cleaning we recommend running the cleaning cycle with cotiseirann Coffee Clean Tablets after approximately 500 cups of coffee or once a month This operation completes the maintenance process of the brew group The Coffee Clean Tablets to clean the Brew Group and the Maintenance Kit may be purchased at your local dealer at the Philips on line shop at http shop philips com or at authorised service centres Warning The Coffee Clean Tablets has no descaling property For descal ing use the Saeco descaling solution and follow the procedure described in the Descaling chapter El Place a cup under the coffee dispensing spout Make sure the water tank is filled with clean water up to the MAX level EJ Put a Coffee Clean tablet in the pre ground coffee compartment E ie ES l EJ Press and release the ues button one or more times to select and activate the pre ground coffee function without adding any ground coffee Green E Start one coffee brew cycle pressing the button Fal When half a cup of water has been dispensed turn off the appliance using the power button and let the solution take effect for approxi mately 15 minutes Make sure you discard the dispensed water Turn o
30. ntrol to off then remove plug from wall outlet 12 Do not use appliance for other than intended use 13 Save these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be performed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if care is exercised in their use Ifa long de
31. offee beans into the hopper ae I il Only coffee beans must be put into the coffee bean hopper If ground coffee instant coffee or any other object is put in the coffee bean hopper it may damage the machine 6 Reposition the coffee bean hopper lid Insert the plug into the socket on the back of the machine EJ insert the plug of the other end of the cable into a wall socket with suitable power voltage EJ switch the power button to I to turn on the machine Black EF The display shows the Stand by icon O E To turn on the machine simply press the KOJ button START Orange ENGLISH 9 The display indicates that the circuit must be primed Circuit Primin STOP amp LP 4 Orange Orange Green In order to avoid that any water is left in the circuit for a long time before starting the machine for the first time and after long periods of inactivity the water circuit needs to be primed This is because we want to offer you a perfect and fresh product El select START by pressing the button The machine starts the automatic priming of the circuit and the bar under the icon shows the operation progress When the process is complete the machine stops dispensing automa tically The display might show the machine warm up icon as shown in the figure Place a container under the dispensing spout E once the
32. on you need to install use clean and descale your appliance In case you need further support please contact the toll free Philipps consumer care help line You can find the phone number on the last page of this document and in the warranty booklet sup plied with the appliance General Description fig 1 Grinder adjustment knob Pre ground coffee compartment Coffee bean hopper Coffee bean hopper lid Control panel Dispensing spout Full drip tray indicator Cup holder grill Drip tray 10 Water dispensing spout removable 11 Coffee grounds drawer 12 Brew group 13 Coffee residues drawer 14 Service door 15 Milk carafe 16 Water tank 17 Power cord socket 18 Main switch 19 Coffee grinder adjustment key Pre ground coffee doser 20 Cleaning brush 21 Grease for the brew group 22 Power cord 23 Water hardness test 24 Espresso coffee brew button 25 Long Espresso brew button 26 Special beverages selection button 27 ON OFF button 28 Aroma Pre ground coffee button 29 MENU button 30 Cappuccino brew button 31 Descaling solution SO NO RAEN ENGLISH 5 Read this user manual carefully before using the appliance and save it for future reference Never allow water to come into contact with any of the electrical parts of the machine Danger of short circuit Steam and hot water may cause scal ding Do not direct the steam or hot water jet towards body parts Carefully handle the steam hot
33. out with a pin Make sure that the machine is off and cold before performing this operation Change coffee blend or adjust the grind as ex plained in section Adjusting the Coffee Grinder Verify the correct cleaning of the carafe and its insertion Descale the machine Turn the machine on Close the service door The brew group automatically returns to the initial position The coffee grounds drawer is inserted There is no water Remove the coffee grounds drawer before remov ing the brew group Fill the water tank and prime the circuit section Using the Machine for the First Time The Brew Group is dirty Clean the Brew Group Brew Group section Rare event that occurs when the machine is automatically adjusting the dose Brew a few coffees as described in section Saeco Adapting System The dispensing spout is dirty Rare event that occurs when the machine is automatically adjusting the dose Clean the dispensing spout Brew a few coffees as described in section Saeco Adapting System The coffee is too coarse The coffee grind is too fine Change coffee blend or adjust the grind as ex plained in section Adjusting the Coffee Grinder Change coffee blend or adjust the grind as ex plained in section Adjusting the Coffee Grinder Circuits clogged Perform a descaling cycle The Brew Group is dirty The dispensing spout is clogged Clean the Brew Group
34. periodically clean both the visible parts of the machine and the area beneath it Before storing the machine we strongly recommend to clean it Water left in the tank and or the water circuit for several days should not be consumed If the machine is going to remain inactive for a long time dispense water from the steam wand and carefully clean the Cap puccinatore if supplied Turn off the power button and clean the machine Finally remove the plug from the socket Wait for the machine to cool down Never immerse the machine in water Store it in a dry place out of the reach of children Keep it protected from dust and dirt It is strictly forbidden to tamper with the internal parts of the machine Malfunction In case of failure problems or a suspected fault resulting from the falling of the machine immediately remove the plug from the socket Never attempt to operate a faulty machine For further information on troubleshooting and service please refer to the Troubleshooting and Service chapters Fire Safety Precautions In case of fire use carbon dioxide CO extinguishers Do not use water or dry powder extinguishers ENGLISH 7 Packagin The original packaging has been designed and constructed to protect the machine during transport We recommend keeping the packaging material for possible future transport Preliminary Operations Remove the drip tray with cup holder grill and the coffee machine from
35. preparing a cappuccino use cold milk Open the milk dispenser and insert the milk carafe into the machine EJ Place the cup for the cappuccino under the carafe dispenser Note Ensure that the cup is positioned correctly under the dispenser to avoid spilling the product Note It is possible to prepare a cappuccino with pre ground coffee Select the function with the se button and pour the coffee in the compartment as described in the respective section EJ Press the button the machine starts preparing the cappuccino U 0 P right away e j CAPPS CINO Lv l Ly A Pr Pee EE E The following icon is displayed during the preheating time required by the machine Orange STOP al When the following icon is displayed the machine dispenses frothed milk directly in the cup E Qs Green The machine pours a predefined quantity of frothed milk into the cup The pouring may be stopped early by pressing the button MEMO 24 ENGLISH STOP WD oF Green e el stop MEMO ON a SS Green EJ Once the milk has been poured the machine starts brewing the coffee EJ The machine pours a predefined quantity of coffee into the cup The pouring may be stopped early by pressing the button After using the milk carafe to prepare the desired number of cappuccino cups wash it as des
36. re ground coffee must be poured into the relevant compartment posi tioned next to the coffee bean hopper Only use ground coffee for espresso machines and never coffee beans or instant coffee Note If no pre ground coffee is poured into the compartment only water will be dispensed If the dose is excessive and 2 or more measuring scoops of coffee are used the machine will not brew the product Also in this case the machine will run an empty cycle and discharge any ground coffee into the coffee grounds drawer G Green To brew coffee El Press and release the e3 button one or more times to select and activate the pre ground coffee function Lift the pre ground coffee compartment lid Add only 1 scoop of pre ground coffee to the compartment Use only the measuring scoop supplied with the machine to perform this opera tion Then close the lid ENGLISH 19 Warning Add only pre ground coffee to the compartment Other sub stances and objects may cause severe damages to the machine Such damages will not be covered by warranty Press and release The button for a cup of espresso or the a button for a cup of long espresso Ef The brewing cycle will start Once the prebrewing cycle is complete coffee begins to come out of the dispensing spout E The coffee brewing process stops automatically It is nevertheless possible to interrupt the coffee brewing process by pressing
37. remove it press on the side hooks Programming The user can change some of the machine operating parameters to suit his her needs Enter the Menu The programming menu can only be accessed when the machine is in on G S Green Press the a button to access programming ENGLISH 45 The first page that is displayed is shown here Orange Programming Controls Changes can be made on each page The and gi buttons allow you to change the value of the func tion among those present on the page The ee button allows you to scroll the functions and store the per formed changes Note Changes can be stored only after the displayed value is changed when the displayed value is changed the OK message appears The ly button allows you to exit the change or programming mode Exiting the Programming Mode To exit programming press the cy button Note The machine will exit the programming mode if the user does not do anything for 30 seconds The settings that were changed but not confirmed will not be stored 46 ENGLISH Functions Coffee Temperature This function allows you to adjust the coffee brewing temperature Orange Timer stand by This function allows you to adjust the time the machine will go into stand by mode after the last brewing Orange Contrast This function allows you to adjust th
38. s program ming the amount of milk to dispense for the hot milk ENGLISH 49 Warning Signals orange colour i a STOP S ce Pog START CALC CLEAN The machine is warming up to brew coffee and dispense hot water and steam The machine is perform ing the rinse cycle Wait until the machine stops the operation The machine needs the INTENZA filter to be replaced LP gf a The Brew Group is being reset due to machine reset Refill the coffee bean hopper with coffee beans and restart the brewing cycle Prime the circuit If this page is displayed after starting the machine this means that the descaling cycle is needed Press the tion Press the KOJ button to go on using the machine button to enter the descaling menu and refer to the relevant sec We remind you that damages caused by failure to descale the machine are not covered by warranty Warning Signals red colour Close the service door No coffee beans in the coffee bean hopper After refilling the hop per the cycle can be restarted The Brew Group must be inserted into the machine Turn off the machine After 30 seconds turn it on again Try this 2 or 3 times If the machine does NOT start contact an author ised service centre U qT Z Insert the coff
39. so experience Saeco Adapting System An intelligent self adjusting system that allows the use of all types of coffee beans available on the market Coffee is a natural product and its characteristics may change according to its origin blend and roast The Saeco coffee machine is equipped with a self adjusting system that allows the use of all types of coffee beans avail able on the market non caramelised The machine automatically adjusts itself in order to optimise the extraction of the coffee ensuring perfect compression of the tablet to obtain a creamy espresso coffee that will release all the aromas regard less of the type of coffee used The optimisation process is a learning process that requires the brew ing of a certain number of coffee cups to allow the machine to adjust the compactness of the ground coffee Attention should be given to special blends which require grinder adjustments in order to optimise the extraction of coffee see section Adjusting the Coffee Grinder Pre brewing Technology Enhancing the Aroma Thanks to the Pre brewing Technology ground coffee is moistened before the actual brewing process ensuring that the aroma can unfold even bet ter Adjustable Ceramic Coffee Grinder a Full Aroma Preservation The ceramic grinders always guarantee accurate grinding for every coffee blend In addition this technology prevents the beans from overheating These two combined factors provide for a f
40. ss the button The machine returns to the normal operat ing mode Note It may happen that even though the button has been pressed hot water does not come out and the following icon is displayed Wait for the warm up phase to end in order to obtain a flow of hot water from the dispens ing spout Warning At the beginning short spurts of hot water may come out Risk of scalding The hot water wand may reach high temperatures Do not touch it with bare hands Eco friendly Stand by Intelia is also very kind to the environment for great taste in good con science Stand b Black The machine is designed for energy saving The machine automatically turns off after 30 minutes of inactivity This feature keeps energy consump tion below 1 Wh in stand by mode Note During the turning off phase the machine performs a rinse cycle ifa coffee product has been brewed To turn on the machine again simply press the ly button if the power button is set to I In this case the machine will perform the rinse cycle only if the boiler is cold ENGLISH 29 Cleaning and Maintenance As some of the parts of your appliance come in contact with water and cof fee during normal use it is important that you clean your appliance regu larly This is an easy procedure with your Philips Saeco Espresso machine Just follow the steps indicated on the display and described below Not doing this will ultimate
41. tachable power supply cord or extension cord is used 1 The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over Table of Contents Introduction General Description fig Important Intended Use Power Supply For the Safety of Others Danger of Burns Machine Location Suitable Location for Operation and Maintenance Cleaning and Storing the Machine Malfunction Fire Safety Precautions First Use Packaging Preliminary Operations Circuit Priming Rinse Self Cleaning Cycle 1 For a perfect Espresso Rinse the coffee circuit if using the machine for the first time or after a long period of inactivity INTENZA Water Filter Optional INTENZA Water Filter Installation Measuring Water Hardness 0000 Espresso Coffee Brewing and Adjustments Pre brewing Technology Enhancing the Aroma 0 Adjustable Ceramic Coffee Grinder a Full Aroma Preservation Aroma Adjustment Select Your Favourite Amount Brewing Coffee Adjusting
42. the STOP button After brewing the product the coffee beans configuration of the ma chine is restored Note Repeat the steps described above to brew other coffees Adjusting the Coffee Length MEMO Function The machine allows you to adjust the amount of brewed coffee according to your taste and or the size of your cups ui or Ww Each time the button is pressed and released the machine brews a pre set oani of coffee This amount may be set again according to your taste Each button may be individually programmed for a specific brew setting Note As an example the following procedure describes the programming of the button which is usually associated with espresso coffee EE Place a cup under the dispensing spout FJ Press and hold the button until the MEMO icon is displayed and remove your finger The machine is now programming The machine begins the brewing phase The STOP icon is displayed EJ From now on press the 2 button when the desired amount of cof fee is reached in the cup Now the button has been programmed Whenever pressed and released the machine will brew the same amount that has just been set 20 ENGLISH Milk Carafe This section explains how to use a milk carafe to prepare a cappuccino or hot milk Note Before using the milk carafe clean it thoroughly as described in the chap ter Cleaning and Maintenance Note The milk must be
43. the coffee grounds drawer it is also necessary to empty and clean the coffee residues drawer Open the service door remove the drawer and empty the coffee grounds After emptying the drawer insert it again in its housing until it locks into place Elif you use the pre ground coffee compartment clean it every week with the supplied brush al Clean the seat of the tray every week through the openings on the bot tom of the machine ENGLISH 31 Cleaning the Milk Carafe After Each Use For a quick cleaning after use proceed as follows El Press the release buttons to remove the lid Rinse the lid and the carafe with fresh drinking water Remove all traces of milk EEJ Attach the lid on the carafe ensure it is locked into place E Remove the top lid and fill the carafe up to the MAX level with fresh drinking water H Replace the lid 32 ENGLISH STOP Orange Green Fal Insert the carafe into the machine and place a container under the cof fee dispensing spout Press the button The following icon is displayed SPECIAL EJ Press the button to start hot milk dispensing E The following icon is displayed during the preheating time required by the machine Once the warm up phase is complete the machine starts dispensing water to be used for cleaning E Once the machine stops dispensing water the cleaning is off Remove the carafe and empty any re
44. the packaging Place the machine in a place that meets the requirements described in the safety regulations E insert the grill drip tray into the seat in the machine Make sure the tray is fully inserted into position The tray must be clipped into to the machine Important Note Insert the plug into the socket only when indicated and make sure the power button is on 0 Carefully read the explanations of all the warnings the machine displays to the user on the control panel LCD display chapter LCD Display War nings NEVER remove the drip tray when the machine is on Wait for a couple of minutes after turning on off as the machine will be carrying out a rinse self cleaning cycle see section Rinse Self Cleaning Cycle Remove the water tank from its seat EJ Rinse and fill it with fresh water making sure that the MAX level indi cated in the tank is not exceeded Completely reinsert the tank into the designated seat pushing all the way to the end the external profiles must match Fill the tank only with fresh non sparkling water Hot water or any other liquid may damage the tank and or the machine Do not operate the ma chine without water Make sure there is enough water in the tank 8 ENGLISH El Remove the coffee bean hopper lid Note The hopper may be provided with different safety features according to the regulations applicable in the country of use of the machine 5 Slowly pour the c
45. ufacturer reserves the right to change the features of the product without prior notice www philips com saeco del 05 09 11 Rev 0O1 15002994
46. ull aroma preservation deliver ing the truly Italian taste in every cup Warning The grinder adjustment knob which is placed inside the cof fee bean hopper must be turned with the Coffee grinder adjustment key only when the coffee grinder is working Do not put any material other than coffee beans into the hopper Do not pour ground and or instant coffee into the coffee bean hopper Warning The coffee grinder contains moving parts that may be dangerous Therefore do not insert fingers and or other objects In case of malfunc tion turn off the appliance by pressing the ON OFF button and remove the plug from the socket before carrying out any type of operation inside the coffee bean hopper Do not pour coffee beans when the coffee grinder is working The machine allows you to make slight adjustments to the coffee grinder to adapt it to the kind of coffee used The adjustment must be performed by means of the pin located inside the 16 ENGLISH Green Green coffee bean hopper This must be pressed and turned using the supplied key only Press and turn the pin one notch at a time and brew 2 3 cups of coffee this is the only way to notice differences in grind The reference marks inside the coffee bean hopper indicate the grind set ting There are 5 different grind settings to choose from with the following references 1 Coarse Grind Lighter taste for dark roasted coffee blends 2 Fine Grind Bol
47. until all water in the carafe has been poured off When the water is finished repeat the operations from point 10 one more time At the end of the second rinsing cycle the thorough clean ing is finished Once cleaning is off disassemble and wash all the components as de scribed in the Weekly Cleaning section 36 ENGLISH Weekly Cleaning Brew Grou The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week E Turn off the machine by pressing the power button and remove the plug from the socket EJ Remove the coffee grounds drawer Open the service door EJ Remove and clean the coffee residues drawer EJ Remove the brew group Pull it by the handle and press the PUSH button The brew group must be washed only with lukewarm water with no detergent E Wash the brew group with lukewarm water and carefully wash the upper filter Before placing the Brew Group in its housing make sure there is no water left in the brewing chamber Fal Make sure the Brew Group is in the rest position the two reference signs must match If they do no match proceed as described in step 7 ENGLISH 37 Make sure that the lever is in contact with the brew group base EJ Make sure the hook to lock the Brew Group is in the correct position to check its position firmly press the PUSH button EJ Insert the Brew Group in its seat again until it locks into place WITHOUT pressi
48. ure that you remain satisfied with your Philips Saeco Espres so coffee machine If not done already please register your purchase on www philips com welcome so that we can stay in contact with you and send you cleaning and descaling reminders For cleaning and descaling use SAECO products only You can purchase these on line at the Philips on line shop at NLhttp shop philips nl BEhttp shop philips be FR http shop philips fr DK http shop philips dk DEhttp shop philips de ES http shop philips es or http tienda philips es IT http shop philips it SE http shop philips se If you have questions about your appliance e g about its installation use cleaning or descaling please refer to this user manual or go for the latest updates to www philips com support Alternatively you may contact our toll free consumer care help line at the phone number listed on the last page of this document Our qualified service staff will help you and if needed trouble shoot your appliance by phone and where possible provide a solution during the call If this is not possible we will help you to initiate any necessary repair in the shortest possible time and with maximum convenience CONSUMER RELATIONS DESKS For Downloads amp FAQs visit our Customer Support Website www philips com support Argentina 0800 888 7532 toll free Australia 1300 363 391 toll free Bahrain 973 17700424 Belgium 0800 80 1
49. warm up is complete the machine performs a rinse cycle of the internal circuits During this phase the icon indicated in the figure will be displayed EJ when the operations described above are complete the icon is displa yed The machine is ready to brew beverages H To brew coffee or dispense hot water or steam and for a proper use of the machine carefully follow the instructions provided Note If the machine is being used for the first time or after a long period of inactivity follow the procedures described in the following section 10 ENGLISH STOP amp Orange Green Green Rinse Self Cleaning Cycle After the automatic priming of the circuit the machine will automatically rinse clean the circuit This cycle allows you to rinse the internal coffee circuits with fresh water The cycle is automatically performed also in the following conditions At machine start up with cold boiler e After priming the circuit with cold boiler During the Stand by preparation phase if a coffee product has been brewed During the turning off phase after pressing the ON OFF button if a coffee product has been brewed A small amount of water will be dispensed to rinse and heat all the ma chine parts in this phase this icon is displayed We strongly recommend to wait for the cycle to finish automatically You can stop dispensing by pressing the button For a perf
50. water spout by its grip Danger of scalding Intended Use The coffee machine is intended for domestic use only Do not make any technical changes or use the machine for unauthorised purposes since this would create serious hazards The appliance is not to be used by persons including children with reduced physical mental or sensory abilities or with scarce experience and or expertise unless they are supervised by a person responsible for their safety or they are instructed by this person on how to properly use the machine Power Supply Power Cord Only connect the coffee machine to a suitable socket The socket to which the machine is connected must be compatible with the type of plug installed on the machine sized to comply with the data on the tag attached to the appliance connected to an efficient earthing system Never use the coffee machine if the power cord is defective or damaged If the power cord is damaged it must be replaced by the manufacturer or by its authorised service centre Do not pass the power cord around corners over sharp edges or over hot objects and keep it away from oil Do not use the power cord to carry or pull the coffee machine Do not pull out the plug by the power cord or touch it with wet hands Do not let the power cord hang freely from tables or shelves For the Safety of Others Prevent children from playing with the machine Children are not aware of the risks related to electr
Download Pdf Manuals
Related Search