H2O Audio iDive 300
Contents
1. A Newer iPod models with a touch screen interface need a special command sequence to transfer between Audio Photo not currently supported and Video modes The Mode button provides 1 touch access to the music and video capabilities of your iPod Note The current firmware release does not support the Photo mode on iPod models with a touch screen interface For more information please visit www h2oaudio com 20 Q Why is the Red LED flashing A The iDive300 is designed to measure battery life of the 3 AA batteries that are used to power the Made for iPod connection electronics and the power amplifier The Red LED will start to flash when the batteries have approximately 25 charge remaining Note the battery indicator of the iPod does not reflect the power remaining in the 3 AA batteries Notes Made for iPod means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards 22 m o 120 audio 11010 Roselle St Suite 150 San Diego CA 92121 Phone 1 800 708 6080 or 858 623 0339 Email support h2oaudio com Copyright Notice This owner s manual is copyrighted all rights reserved It may not in whole or in part be copied photocopied reproduced translated or formed into any electronic format without p2. the iDive300 2 Place iPod in the inserts with the iPod dock connector facing toward the cam knob 3 Insert the connector cable into the dock connector of the iPod with the H20 Audio logo facing up 4 Depending on your iPod model press and hold the Play Pause button or press the Power button to turn the iPod on 5 IMPORTANT For touch screen iPod models to prevent the display screen from locking access the General Settings to turn the Auto Lock feature off Settings General Auto Lock Never VII Operation c a ee A Previous Fast forward Volume Play Pause Down Controls Select Next Fast forward Power On Off Press and hold the power button for 2 seconds to turn the iDive300 on off After turning the iDive300 on all 3 LEDs on the back of the case should illuminate within a few seconds If connected successfully only the Green LED should remain lit iPod Authentication Green LED indicates successful connection of the iPod Red LED indicates a failed connection of the iPod When the Red LED is illuminated controls will be limited to adjusting the volume of the built in amplifier Blue LED indicates that the authentication timed out When the Blue LED is illuminated there is some limited function of the iPod controls In case o
3. IMPORTANT PLAY HEADPHONES AT 90 VOLUME FOR 30 MINUTES BEFORE INITIAL USE OR AFTER AIR TRAVEL Caution Listening to music at high volume may damage your hearing The H20 Audio iDive300 Deep Dive Waterproof Case and Speakers feature sealed watertight speaker chambers During initial use or after air travel the speakers may sound distorted or operate at a low audio level due to a vacuum formed in the speaker chamber during air shipment Volume and sound quality will return to normal once the pressure equalizes Playing the headset at 90 volume for 30 minutes typically solves this problem If the problem still occurs wait 24 hours and test again as the speakers will usually equalize within a short period of time If your speakers do not equalize or if you have any questions please contact H20 Audio Customer Service at 1 800 708 6080 or support h2oaudio com allas 20audio www H20Audio com IWI VE S00 Deep Dive Waterproof Case amp Speakers Depth Rating 300ft 90m iPod touch y7 iPod nano iPod classic iPod nano 8GB 16GB 32GB KA 3rd generation video 80GB 160GB f 2nd generation aluminum MIB 4GB 8GB ma 2GB 4GB 8GB Made for iPod iDV1 75 20080819 iPod iPod iPod nano 5th generation video 5th generation video Ist generation 60GB 80GB 30GB 1GB 2GB 4GB For updated manuals please visit our web site www h2oaudio com O ring Lanyard Hole Insert Holes amp Height A
4. cluding return shipment to you when the unit is still in the warranty period Shipping amp handling charge will apply for service repairs made beyond the 1 year warranty period For any non warranty service you will be advised as to repair costs prior to any work being done XVI Returns Prior to any return a Return Authorization RA number must be obtained To receive an RA number go online to www h2oaudio com returns php and follow the simple instructions on how to return a product Proof of purchase from an Authorized Dealer will be required A copy of the original sales receipt and a copy of the owner s portion of the warranty card must accompany all correspondence regarding the equipment covered by this warranty agreement or in direct reference to this warranty FAQ s Q Will this product work with the original iPhone or 3G iPhone A Yes however the user will experience interference with phone functions Q Why does the volume turn low when install my iPod A The iDive300 has an internal amplifier to reproduce audio down to depths of 300 feet The water pressure at this depth requires a powerful amplifier to drive the sound through the headphones At full depth the force of the sound waves is mitigated by the water pressure At lesser depths or on the surface this loud volume can damage your hearing As a safety precaution the iPod volume is set to 1 4 as soon as an iPod is connected Q Why is there a Mode button
5. djuster Holes Connector Cable LED lights y 2 iPod Control Buttons Cam Knob Lock Depth Rating 300ft 90m Quickstart Instructions Getting Familiar with the iDive300 Before using the iDive300 for the first time it is highly recommended that you become familiar with l Read Getting Familiar with the iDive 300 opening and closing the case to ensure the case is sealed properly during use To verify that you have sealed the case properly we recommend that you test the product without an iPod inside before initial use Il Unlock and open case Please follow the instructions below Read the iDive300 instruction manual to familiarize yourself with the product Unlock and open the case see page 6 and verify the blue O ring is clean and free of debris Close and lock the case see page 7 Immerse the case without an iPod inside in water and soak for 30 min Manipulate the iDive300 controls during submersion Remove from the water and dry the exterior Visually inspect the case for any sign of leaks before opening Ill Install batteries 3 AA IV Install iPod specific inserts and height adjusters see page 10 for fit chart V Install iPod VI Turn on iPod VII Close and lock Case E Il The O rin VIII Press and hold the power button on the iDive300 case The removable blue O ring retained in the lid of
6. f a Blue LED Restart the iDive300 by turning the power off then on If this does not solve the problem 1 Turn off the iDive300 2 Disconnect the connector cable from the iPod 3 Ensure the iPod is on 4 Reconnect the connector cable to the iPod 5 Turn on the iDive300 In case of a Steady Red LED 1 Ensure you are using a supported iPod model 2 Ensure the iPod is fully charged 3 Ensure the iPod is turned on 4 Disconnect amp reconnect the connector cable In case of a Flashing Red LED 1 Batteries of the iDive300 case are running low change or recharge them soon Mode Button Note The current firmware release does not support the Photo mode on iPod models with a touch screen interface For touch screen iPod models it s necessary to use the mode button to cycle between the various iPod menus modes i e Photo menu not currently supported Video menu Audio menu etc The mode button does not function with scroll wheel controlled iPod models 1 Starting from the Audio menu press the Mode button this will transfer the user to the Photo menu not currently supported 2 Press the Mode button again to transfer to the Video menu 3 Press the Mode button again to transfer to the Photo menu not currently supported 4 To return to the Audio menu press the Mode button one additional time VIII Speakers iDive300 speakers feature specially designed clips for attach
7. facing out 3 Apply a thin layer of the supplied silicone grease to the O ring Cleaning amp Storing the O ring It is extremely important that you keep the O ring clean and free of sand dirt hair lint and other debris To clean the O ring 1 Remove the O ring from the case using the supplied O ring remover 2 Wash the O ring in warm fresh water strong detergents soaps and chemicals MUST NEVER be used to clean the case or the O ring 3 Allow O ring to air dry 4 Install O ring into the lid ensuring it is aligned properly with the round side of the O ring facing out 5 Apply a thin layer of the supplied silicone grease to the O ring For long term storage of the O ring store in a plastic bag out of direct sunlight Ill Opening amp Closing the Case To Open Case Ensure the exterior of the case and the immediately surrounding area is dry before opening the case The internal components of the iDive300 are not waterproof 1 Open the cam knob lock 2 Rotate the cam knob counter clockwise 180 3 Open Lid Please note The lid may be difficult to open due to a vacuum created in the case during air travel or shipment To Close Case V Install iPod specific inserts and height adjusters 1 Close lid The inserts and height adjusters are used to securely hold your iPod in the correct location inside the case 2 Rotate the cam knob clockwise 180 3 Close the cam knob lock Consult the following chart to determine which
8. gal in some areas Avoid using speakers at high volume Hearing experts advise against continuously loud and extended play If you experience ringing in your ears reduce volume or discontinue use XIII Warranty Coverage 1 Year Limited Warranty H20 Audio s 1 year limited warranty covers defects in materials and or workmanship of all H2O Audio product 1 year from date of original purchase This warranty does not apply to any products which have been neglected altered abused used for a purpose other than the one for which they were manufactured repaired by customer or any party without H20 Audio s written authorization or used in any manner inconsistent with H20 Audio s instructions Please refer to the care and maintenance instructions for more details Product Manuals are available for download on the H20 Audio website as well as packaged with the product Warranty claims involving personal property damage will be put through a series of tests to determine if the product has been misused or improperly cared for Should a product be determined by H20 Audio to have manufacturing or material defects which resulted in damage to personal property H20 Audio at its sole discretion will make reparation to the customer in the form of a repair or replacement of equal value No compensation for loss of data ect Products must be purchased from an Authorized Dealer The product warranty program will not be valid for product purchased thro
9. inserts and height adjusters should be used with your iPod model Please note some iPod models will not require height adjusters iPod Model Upper Insert Letter Lower Insert Letter Height Adjuster Number Podtouch APB iPod 5 Gen 30cb Bo f BC iPod 5 Gen 60 80Gb _ B B N A NV Install batteries er 6 8 E cee iPod classi C E ee a f F 2 Disconnect and remove iPod from case if installed iPod classic 160Gb 3 3 Turn the battery cover screw counter clockwise until the screw loses contact with the insert plate iPod nano 1 Gen N A 4 Remove battery cover WON Pod nano 2 Gen ND 5 Install 3 AA batteries in the battery compartment Make sure the positive and negative ends of the iPodnano3 gen D dD N A battery are oriented per the inscribed markings in the case g 6 Reinstall and close battery cover The iDive300 is not certified to work with the iPhone or iPhone 3G and will cause interference with phone capabilities Included insert and height adjusters Inserts and height adjusters are labeled to aid identification SS iPod classic 160 Gb SS Insert C Insert D Height Adjuster 3 Height Adjuster 4 As new iPods become available please check our web site for updates on Inserts and height adjusters VI Insert iPod 1 Ensure the correct inserts and height adjusters are installed for your iPod PLEASE NOTE If the correct insert and height adjusters are not used you may damage or destroy your iPod and
10. ment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technical for help Note The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment XII General Use Notice Read this manual carefully If you have any questions please contact H20 Audio customer support prior to use Improper use of this system may cause the user to make mistakes or decisions that may lead to serious injury or death Important warning and disclosure Any individual intending to utilize this product during S C U B A diving activities must be properly trained and certified by an accredited agency Further it is recommended that all divers stay within recreational dive limits and follow all safety stop considerations Those users that elect to utilize this system at or near the water s surface must maintain safety awareness of moving watercrafts Important warning and disclosure It can be potentially dangerous to play your speakers while engaging in activities that require your full attention You should exercise extreme caution or discontinue use in potentially hazardous situations Do not use the speakers while driving cycling or operating any motorized vehicle It may create a traffic hazard and is ille
11. ment to mask straps The mask clips are removable for users who wish to put the speakers inside a diving hood or under their mask strap For Mask Strap Mounting To Remove Mask Clip Feed mask strap through the slits in each slot of the clip IX General Storage Procedures For long term storage store in a cool dry place out of direct sunlight CAUTION The life of a O ring is typically one 1 year Contact H20 Audio for spare O rings and silicone grease Always remember to reinstall the O ring before next use Do not expose the case to extreme heat such as the inside of a hot car or in direct sunlight such as on a beach or boat deck Doing so may cause damage and subsequent flooding CAUTION The case is susceptible to internal condensation with extreme temperature fluctuations Use above 105 F 40C can result in internal condensation When used in temperatures below freezing frost will appear on the interior of the case CAUTION Do not store case in the following environments Solvents or other chemical fumes High humidity High Ozone Extreme temperature fluctuations Storing the case in these conditions may lead to a damaged case causing it to leak Rinse the EXTERIOR of the system in fresh water after EACH use 1 Make sure the case is securely closed 2 Soak in clean fresh water for 30 minutes 3 Rinse the entire system with freshwater 4 Completely dry the entire exterior of the system using a clean s
12. oft cloth 5 Let air dry Strong detergents soaps and chemicals MUST NEVER be used to clean the system X Contact Us Customer Support is available Monday to Friday 9AM 5PM PT web www h2oaudio com Phone 1 800 708 6080 or 858 623 0339 Fax 858 225 0815 Email Support h2oaudio com XI FCC Certification This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital service pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off an on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equip
13. rior consent in writing H20 Audio is a registered trademark of H20 Audio Inc Apple and iPod are registered trademarks of Apple Inc Patents 6396769 6614722 6954405 7263032 Others Pending
14. the iDive300 is what keeps your iPod safe and dry Green LED should light on back of case The supplied silicone grease helps ensure the O ring will not twist or become dislodged when closing or opening the case Lubricating the O ring does not improve the seal and only a small amount of silicone grease is necessary to lubricate the O ring Use only the silicone grease provided to lubricate the O ring Am BWN Call H20 Customer Service if you have any questions or concerns IT IS EXTREMELY IMPORTANT YOU ENSURE THE O RING IS PROPERLY SEATED IN ITS TRACK AND IS FREE OF DEBRIS BEFORE EACH USE FAILURE TO DO SO MAY CAUSE DAMAGE TO OR DESTROY YOUR IPOD Prior to use verify 1 The O ring is lightly lubricated and seated within the track in the lid 2 The O ring and contact surface are free of scratches and other imperfections Do NOT use if 1 The O ring is dry cracked twisted and or out of alignment 2 O ring and or contact surfaces have any dirt lint hair and or other debris 3 The O ring and contact surface have scratches and other imperfections Replacement H20 Audio has provided an extra O ring The O ring should be replaced annually or in the event of damage loss overexposure to direct sunlight or become misshaped through misuse To replace the O ring 1 Remove the O ring from the case using the supplied O ring remover 2 Install the new O ring into the lid ensuring it is aligned properly The round side of the O ring should be
15. ugh an unauthorized source For a directory of H20 Audio Authorized Dealers please visit the store locator section on the company website If you have questions as to whether or not a dealer is authorized please call Customer Support This warranty applies to customers who properly fill out and complete the warranty registration with proof of purchase within 30 days of purchase Failure to complete the registration will void the warranty H20 Audio will at its sole discretion and without charging the customer repair or replace any components that fail in normal use The warranty is valid only for the original owner who purchases the unit from an authorized dealer Transfers are not qualified for warranty To Obtain Service Please go to support section of our website or contact customer support at Customer Support Hours and Contact Information Monday through Friday 9AM to 5PM PT Tel 858 623 0339 Toll Free 800 708 6080 support h2oaudio com PLEASE NOTE No service returns will be accepted without a pre return authorization RA which must be clearly marked on the outside of the package The product will be returned COD if submitted without an RA Upon receipt your return will be carefully inspected and assessed for damage and warranty coverage if applicable The system may be pressure tested to verify the integrity of the product prior to any service All warranty costs will be covered according to the terms and conditions provided in
Download Pdf Manuals
Related Search