Paxton 360-864BL-US magnetic card reader
Contents
1. 10 11 2010 Ins 30040 US PROXIMITY architectural reader Technical Support D 1 800 672 PAXT support paxton access com Technical help is available Monday Friday from 02 00 AM 8 00 PM EST Saturday from 04 00 AM 08 00 AM EST Documentation on all Paxton products can be found on our web site http www paxton access com Fitting Ensure that the backbox is mounted vertically and is square with the wall surface Care must be taken when doing this as no further twist adjustment is possible within the reader mountings Reader insert The reader insert is held against the backplate by an outer decorative bezel secured with 4 small screws Remove these screws to release the bezel and refit after adding the insert If you have made an insert of less than 3 16 inch thick this can still be fitted by using the 3 nylon screws supplied in the fitting kit to hold the insert against the bezel see diagram a Mounting the reader Line up the two locating pins on the top of the reader with the top plate inside the backbox Once located the reader can be clipped into the box at the bottom using the clip feature Check that the reader is located against the surface of the wall If there is a gap between the reader and the wall or if the reader will not successfully clip into the box remove the reader and adjust the mounting plates inside the backbox using a 3 mm Allen key Removing the reader To remove the2. d 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment
3. eader or keypad are correct Connections Check the wiring and integrity of the connectors If possible test this reader on the other port Cable To confirm that an extended reader cable is not at fault wire the reader directly to the port Supply voltage Confirm that the voltage is within specification see table User token Confirm that the user token used for testing is OK by presenting it to a known working reader Interference Confirm whether the reader works when tested in hand and not mounted on the wall Ensure PROXIMITY readers are not mounted back to back or that there is no interference from other RF devices 2 Net2 What to do if a user has no access Check the reader LEDs when a card is shown No LEDs the reader has no power No change in display try the card on a known working reader If there is still no response replace the card Green LED flashing when a card is presented check relay 1 LED to check for activity and also the lock wiring Red LED is flashing when a card is presented check the validity of the user at the PC Check user s access level and ensure they should have access by clicking on Current Validity Check the Valid Until date and confirm this has not expired Reinstate the ACU from the doors screen Select the ACU s you wish to reinstate and then click OK 3 Switch2 Adding an additional card pack You need to be in possession of the original enrolment card Present the
4. original enrolment card to the reader and the Amber LED will flash Green amp Red LEDs will be off then present the Enrolment card from the new card pack the reader will beep and all LEDS will be lit The additional cards will now be valid Repeat this with each reader and with any additional card packs Any valid enrolment card can be used to add further packs This is the same for enrolling function card packs onto a system 4 Switch2 How to reset the controller Disconnect the power and remove the wires from the Green and Mauve terminals Insert a wire link between the Green and Mauve terminals Reconnect the power the unit will bleep 4 times Disconnect the power and remove the link wire reconnect the Green and Mauve wires Reconnect the power the unit will bleep 3 times per second The unit is ready to be enrolled Ul BR WN Be Suitability Security sensitive doors of Accepts customised inserts and bezels S 12 inches between readers Wet environments S Readers mounted together Specifications Max Min Operating temperatures all items 20 C 4 F 55 C 131 F Cable length Max Min Carrier frequency S eee 125 kHz ee Clock and data bit period 600 us Width Height Depth Read Range Token Keyfob Hands Free Token 7 FCC Compliance This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference an
5. reader insert the tool provided into the cut out on the underside of the reader Push up the clip and pull the reader from the backbox Connection to a control unit reader port IMPORTANT This reader cannot be connected in parallel with other readers and keypads Connection modules Reader junction box 325 020 US This module can be used to provide a connection point for the reader RJ45 plug The terminals on the module are then wired color for color to the controller Alternatively the reader can be wired directly into the screw terminals of the control unit by first cutting off the RJ45 plug and stripping back the wires in the cable Cable extensions Reader Port Module 325 030 US This module may be purchased separately to speed up the installing and replacement of readers The reader port module is designed to convert the standard reader ports on Switch2 and Net2 controllers to accept one or two RJ45 connections Pull off the screw terminal block from the reader port and simply replace it with this module Readers can be extended using Belden CR9538 8 core overall screened cable to a maximum of 500 feet Technical Help Here is the list of topics about this product that receive the most technical support inquiries We list them here to help you speed up the installation and trouble shooting process 1 Readers Keypads not working Software settings Confirm that the settings of the r
Download Pdf Manuals
Related Search