Peerless PLAV70-UNL-S flat panel wall mount
Contents
1. Phillips Adapter Bracket Fasteners M4 x 12 mm 6 M5 x 12 mm 4 M6 x 12 mm 4 504 9013 520 1027 520 1128 M8 x 16 mm 6 520 9257 M6 x 20mm 4 MB x 25 mm 4 520 9402 520 9543 a S multi washer 6 580 1036 M4 x 25 mm 4 M6 x 25mm 4 M8 x25 mm 4 504 1015 M6 x 30 mm 4 520 1208 520 1031 510 9109 M8 x 40 mm 4 520 1136 I D 22 5 6 mm 4 540 1057 I D 34 8 7 mm 4 540 1059 4 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 Installation to Wood Stud Wall A WARNING Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Tighten wood screws so that wall plate is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Install ers are responsible to provide hardware for other types of mounting situations not evaluated by UL Wall plate A can be mounted to two studs that are 16 apart Use a stud finder to locate the edges of the studs Use of an ed2. MULTI WASHER SCREW lt i ADAPTER BRACKET BB If you have any questions please call Peerless customer care at 1 800 865 2112 For Bump out or Recessed Back Display 7 2 Begin with longer length screw hand thread through multi washer adapter bracket and spacer in that order into S display as shown below Screw must make at least three full turns into the mounting hole and fit snug into place Do not over tighten If screw cannot make three full turns into the display select a longer length screw from the baffled fastener pack Repeat for remaining mounting holes level brackets and tighten screws fig 7 2 Tee SPACER P SCREW s ADAPTER BRACKET BB If you have any questions please call Peerless customer care at 1 800 865 2112 41 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 Mounting and Removing Flat Panel Screen A WARNING e Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television O Refer to mount instruction sheet for attachment of adapter bracket to mount Hook adapter brackets BB onto adapter bracket AA then slowly swing screen in as shown Turn screws clockwise at least six times to prevent screen from being removed as shown in detail 4 Tighten using allen wrench CC Screen can be adjusted horizontally if desired Note To lock the screen down tighten screws to adapter bracket as sho
3. 06 27 11 A WARNING e If you are uncertain that product is properly installed call customer care Note There are three mounting positions D The center position is shown right Arm assemblies must be mounted with one mounting hole separating them Slide washers J over wall support arm axles D Next insert plastic caps N into axles Then insert holding pins M into axles See detail 1 2 1 Place arm assembly C with washers J into wall plate A Insert axle assemblies shown in detail 1 through wall plate A arm assembly C and washers J Lock axles in place by aligning holding pins M with notches shown in detail 2 DETAIL 1 2 2 Insert socket cap screws K into hole at bottom of wall support arm axles D as shown in detail 3 Tighten screw using 9 64 allen wrench Q j Note Fit of axles D into wall plate A and arm assembly C will be tight Gently tap into place with a hammer if necessary DETAIL 3 To route cables through cord management To route cables using cable management clips channels Slide one mesh sleeve T over Snap eight cable management clips R into both each cable Use cable ties S to tighten mesh swing arms C as shown in figure 3 2 Cable ties sleeves to cables S are used with clips for cord management ES Pull cords through cord management Slide one mesh sleeve T over each cable Use channels leaving enough slack to
4. I For tilt adjustment gently push back on the top of plasma to relieve pressure on knob Adjust tilt to desired position and tighten tilt adjustment knob H then securely tighten all four M10 screws F using 6 mm allen wrench U SWIVEL BOX fig 6 1 Adapter bracket not shown for clarity Adapter bracket not shown for clarity 9 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 Installing Adapter Brackets A WARNING e Tighten screws so adapter brackets are firmly attached Do not tighten with excessive force Overtightening can cause stress damage to screws greatly reducing their holding power and possibly causing screw heads to become detached Tighten to 40 in Ib 4 5 N M maximum torque e If screws don t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured damage may occur to screen or product may fail To prevent scratching the screen set a cloth on a flat level surface that will support the weight of the screen Place screen face side down Refer to screen manufacturers instructions or customer service for removing any knobs base cover or screw s on the back of the screen to prepare mounting These need to be removed to allow the adapter brackets to be attached Select the small medium large or extra large screws from the baffled fastener pack then attach adapter brackets BB to screen following figure 7 1 or 7 2 NOTE Top a
5. allow full cable ties S to tighten mesh sleeves to cables range of movement for swing arm assembly C as shown if figure 3 1 MANAGEMENT CHANNEL 7 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 Attach two pieces of vinyl trim E to wall plate A Next attach one piece of vinyl trim to bottom of swivel box on arm assembly C 4 1 Insert one finishing cap L into each unused hole of wall plate A SWIVEL BOX Insert and tape carriage bolt I into top hole of tilt roll assembly B Attach tilt roll assembly to adapter bracket AA with four M10 socket screws F Tighten screws using 6 mm allen wrench U Do not overtighten screws Overtightening may hin der roll option 8 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 A WARNING e Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV O Insert two M10 screws F into swivel box on arm assembly C as shown Leave approx 1 4 of exposed thread SWIVEL BOX CS Hook tilt roll assembly B onto M10 screws F Insert carriage bolt I into slot of swivel box as shown in figure 6 1 Install nylon washer G and tilt adjustment knob H RR IES SE Afer titis aep al fasteners must be tightened allow for tilt adjustment Remove tape from carriage Failure to do so Will result in damage to the mount bolt
6. ely lift and position equipment Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holding power This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury This product was designed to be installed on the following wall construction only WALL CONSTRUCTION HARDWARE REQUIRED Wood Stud Included Wood Beam Included Solid Concrete Included Cinder Block Included Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit ACC415 not evaluated by UL Brick Contact Qualified Professional not evaluated by UL Other or unsure Contact Qualified Professional Tools Needed for Assembly Accessories e stud finder edge to edge stud finder is recommended External Wall Plate WSP716 WSP716 S WSP724 e drill WSP724 S Metal Stud not evaluated by UL e 7 32 drill bit for wood studs e 3 8 masonry drill bit for concrete e 7 16 socket wrench with extension recommended e level phillips screwdriver e 3 4 open end wrench Table of Contents gt gt S Pants IS R R 3 Installation to Double Wood Stud Wall ssri rissaa mn aaa sanecelusepasbasetocdatduads setduu chute aA a Aa aaa a a iaaa NAA 5 Installation to Solid Concrete Or Cinder BIOoGkK s Saa zt 527 asenaan aa 2 aiaa 2 Taa x HRS ainai Lona 6 2 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 Wall Arm Parts L
7. end users of Peerless products will be free from defects in material and workmanship under normal use for a period of five years from the date of purchase by the original end user but in no case longer than six years after the date of the product s manufacture At its option Peerless will repair or replace or refund the purchase price of any product which fails to conform with this warranty In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable express warranty set forth above Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty does not cover damage caused by a service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless b the failure to utilize proper packing when returning the product c incorrect installation or the failure to follow Peerless instructions or warnings when installing using or storing the product or d misuse or accident in transit or otherwise including in cases of third party actions and force majeure In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product whether or not secured by a security device which may be included with the Peerless product Some states do not allow the exclusion or limitation of incidental o
8. es The top mounting slots concrete surface D Use wall plate A making sure that it is level as should be located 43 below the desired screen center Use the masonry bit to drill 3 8 10mm Y dia holes to a minimum depth of 3 76 mm Insert anchors V in holes flush with wall as shown right Place wall plate A over anchors V and secure with 5 16 x 3 wood screws O and washers P A WARNING e Tighten wood screws so that wall plate is firmly at tached but do not overtighten Overtightening can damage screws greatly reducing their holding power e Never tighten in excess of 80 in Ib 9 N M A WARNING gt Always attach concrete expansion anchors directly Tighten all fasteners to load bearing concrete Never attach concrete expansion anchors to con crete covered with plaster drywall or other finishing material If mounting to concrete surfaces covered with a finishing surface is unavoidable not evaluated by UL the finishing surface must be counterbored as shown below If plaster drywall is thicker than 5 8 custom fasteners must be supplied by installer not evaluated by UL INCORRECT CUTAWAY VIEW 6 of 14 ISSUED 06 05 06 SHEET 202 9142 7
9. ge to edge stud finder is highly recommended Based on their edges draw a vertical line down each stud s center Place wall plate on wall as a template The top mounting slots should be located 43 below the desired screen center Level plate and mark the center of the eight mounting holes Make sure that the mounting holes are on the stud centerlines Drill eight 7 32 dia holes 3 deep Make sure that the wall plate is level secure it using eight 5 16 x 3 wood screws O and washers P Skip to step 2 on page 7 5 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 Installation to Solid Concrete or Cinder Block Wall A WARNING gt When installing Peerless wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block Cinder block must meet ASTM C 90 specifications It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor e Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components a template to mark hol
10. ist PLAV70 UNL PLAV70 UNL S PLAV70 UNLP PLAV70 UNLP S Part Part 201 1040 201 4040 201 1042 201 4042 201 1044 201 4044 201 1041 201 1041 600 1012 600 1012 520 9262 520 9262 540 1074 540 1074 560 0108 560 0108 520 1315 520 1315 540 1070 540 1070 520 1210 520 1210 590 1123 590 1123 580 1166 580 1166 590 1007 590 1007 520 1243 520 1243 540 1063 540 1063 9 64 allen wrench 560 9728 560 9728 cable management clips 590 1166 590 1166 cable tie 590 1168 590 1168 36 polyester mesh sleeve 600 1015 600 1015 6 mm allen wrench 560 9716 560 9716 concrete anchor 590 0321 590 0321 Some parts may appear slightly different than illustrated wall plate tilt roll assembly arm assembly wall support arm axle vinyl trim M10 x 1 5 x 15 mm screw 062 nylon washer tilt adjustment knob carriage bolt 3 8 16 x 3 25 062 delrin washer 8 32 x 375 socket head screw plastic finishing cap holding pin retainer plug 5 16 x 3 wood screw 068 metal washer lt CHMOADNVOZSrFAC LTOAMMOODDYD O2FNAMAWDANNANABDAAAWN AAA 3 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 Adapter Bracket Parts List PLAV70 UNL PLAV70 UNL S PLAV70 UNLP PLAV70 UNLP S Description Qty Part Part Part Part AA adapter bracket 1 201 1110 201 4110 201 1110 201 4110 BB shallow adapter bracket 2 201 1511 201 4511 201 1514 201 4514 CC allen wrench 1 560 9646 560 9646 560 0072 560 0072 7 CC 27 OCB OCA
11. nd bottom mounting holes on screen must be used for attaching brackets Verify that all holes are properly aligned and then tighten screws using a phillips screwdriver X 0 0 6 S U U 0 0 CENTER BB BRACKETS L VERTICALLY J ON BACK OF SCREEN Note X dimensions should be equal A MULTI WASHER Notes MEDIUM HOLE FOR M5 SCREWS s The number of fasteners used will vary depending upon O the type of screen SMALL HOLE FOR M4 SCREWS e Multi washers and spacers may not be used depending O upon the type of screen LARGE HOLE FOR M6 SCREWS e Use the corresponding hole in the multi washer that C matches your screw size as shown NOTE For flat back screens proceed to step 7 1 For bump out or recessed back screen skip to step 7 2 10 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 For Flat Back Display Begin with the shortest length screw hand thread through multi washer and adapter bracket into display as L shown below Screw must make at least three full turns into the mounting hole and fit snug into place Do not over tighten If screw cannot make three full turns into the display select a longer length screw from the baffled fastener pack Repeat for remaining mounting holes level brackets and tighten screws NOTE Spacers may not be used depending upon the type of display fig 7 1 DISPLAY
12. peerless Models PLAV70 UNL PLAV70 UNL S PLAV70 UNLP PLAV70 UNLP S Installation and Assembly Universal Articulating Swivel Double Arm for 42 65 Plasma Screens eL UL lus usten Max UL Load Capacity 200 Ib 91 kg 2300 White Oak Circle Aurora Il 60502 800 865 2112 Fax 800 359 6500 www peerlessmounts com ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 NOTE Read entire instruction sheet before you start installation and assembly A WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings for US customers please call Peerless customer care at 1 800 865 2112 for all international customers please contact your local distributor This product should only be installed by someone of good mechanical aptitude has experience with basic building construction and fully understands these instructions Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Never exceed the Maximum Load Capacity See page one If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to saf
13. r consequential damages so the above limitation or exclusion may not apply to you This warranty is in lieu of all other warranties expressed or implied and is the sole remedy with respect to product defects No dealer distributor installer or other person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless product This warranty gives specific legal rights and you may also have other rights which vary from state to state peerless AV www peerlessmounts com 2011 Peerless Industries Inc 14 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11
14. wn in detail 4 To remove screen from mount loosen screws swing screen away from mount and lift screen off of mount SAFETY SECURITY SCREWS DETAIL 4 12 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 Depending on the specific size amp weight of the plas ma articulating swing arm may be angled at different positions causing plasma to appear to lean sideways at different articulating positions Tilt roll assembly B allows plasma to be manually adjusted so plasma can be horizontal at all positions To adjust gently rotate plasma by hand to desired position ARTICULATING ARM PLASMA If it is too difficult to adjust roll of plasma loosen screws shown in figure 9 1 using a phillips screwdriver IMPORTANT Do not loosen or tighten screws more than 1 8 turn e To raise screen turn hex nut shown in figure 10 1 clockwise with 3 4 open end wrench not provided Position of screen may be adjusted vertically up to 79 in each direction by doing the following e To lower screen turn hex nut shown in figure 10 1 counterclockwise with 3 4 open end wrench not provided 13 of 14 ISSUED 06 05 06 SHEET 202 9142 7 06 27 11 2011 Peerless Industries Inc All rights reserved All other brand and product names are trademarks or registered trademarks of their respective owners LIMITED FIVE YEAR WARRANTY Peerless Industries Inc Peerless warrants to original
Download Pdf Manuals
Related Search