Moog Videolarm OH121TL
Contents
1. Nideolarm Specification Catalog Number Section INSTRUCTIONS 5178 1b MODEL Indoor Ceiling Housings OH201TL CL OH161TL CL OH121TL CL OH206T C OH166T C OH126T C STANDARD INSTALLATION PROCEDURE INCLUDES MODELS OH201TL CL OH161TL CL OH121TL CL OH206T C OH166T C OH126T C A As Use Only Class 2 Power Supply os MODEL OH201TL CL OH161TL CL OH121TL CL Housing Contents 1 Tinted clear dome 2 Support channels 1 Black opaque liner 1 FM2 camera bracket assembly 1 Black dust cover Remove contents from the box Remove the ceiling tile in the desired location Place the dome so that it rests on the ceiling grid NOTE Be sure that the grid is adequately supported Place the black opaque liner in the dome and rotate it to the desired viewing postion Only one viewing slot is provided in the liner If more than one camera is being mounted additional holes can be cut in the liner using a hole saw or utility knife Be sure to orient each viewing hole correctly Assemble the FM2 camera bracket Align the long slots of the bracket arms Using a carriage bolt 5 16 washer 1 4 washer lockwasher and hex nut attach the bracket arms together loosely Figure 1 next page Assemble the Support Channels Slide the smaller channel through the slot on the larger one Figure 2 next page BE CAREFUL WHEN HANDLING SUPPORT CHANNELS EDGES MAY BE SHARP Use the 1 4 x 202. bolt supplied to connect the FM2 to the cen ter hole on the support channel assembly NOTE For added flexibility the camera can be mounted on either the short or long side of the bracket arm Securing tabs are provided to hold the bracket in the liner Bend the corresponding tab with a screwdriver Figure 2 next page Connect the camera to the FM2 bracket and place the assembly in the dome so that the edges of the bracket will rest on the flange of the dome Figure 3 next page Tighten all connections and complete wiring of the camera Place the black dust cover over the top of the dome so that the dust cover is sitting on the support channels REVISION DATE August 7 2003 PRODUCT INSTRUCTIONS MODEL OH206T OH166T OH126T Housing Contents 1 Tinted clear dome 2 Support channels 1 FM2 camera bracket assembly Remove contents from the box Remove the ceiling tile in the desired location Place the dome so that it rests on the ceiling grid NOTE Be sure that the grid is adequately supported Assemble the FM2 camera bracket Align the long slots of the bracket arms Using a carriage bolt 5 16 washer 1 4 washer lockwasher and hex nut attach the bracket arms together loosely Figure 1 next page Assemble the Support Channels Slide the smaller channel through the slot on the larger one Figure 2 next page BE CAREFUL WHEN HANDLING SUPPORT CHANNELS EDGES MAY BE SHARP Use the 1 4 x 20 bolt
3. supplied to connect the FM2 to the cen ter hole on the support channel assembly NOTE For added flexibility the camera can be mounted on either the short or long side of the bracket arm Securing tabs are provided to hold the bracket in the dome Bend the corresponding tab with a screwdriver Figure 2 Connect the camera to the FM2 bracket and place the assembly in the dome so that the edges of the bracket will rest on the flange of the dome Figure 3 next page Tighten all connections and complete wiring of the camera MODEL OH202D 162D 122D Contents include one black acrylic dome 1 Remove contents from the box 2 Remove the ceiling tile in the desired location 3 Place the dome so that it rests on the ceiling grid DOME CARE Please use the following precautions to maintain the dome s perfect optical properties e Always handle the dome from the outside of its circular flange e If dust or other contaminants accumulate on the dome they should be removed with clean air pressure e If compressed air is not available the dome can be cleaned with any non abrasive cleaning cloth and a cleaning agent that is safe for use on acrylic 2525 Park Central Blvd Decatur Ga 30035 e 770 987 7550 800 554 1124 U S amp Canada Fax 800 826 0366 www videolarm com Figure 1 Figure 2 Figure 3 rare Jory oesonpron id 92 WSLFO1 1 4 SAE Flat Washer 18 9 SS 6 92 WSFLO5 5 16 Flat Washer
4. SS 30 VL732 0 1 Multiple Camera Bracket 8 96 RSORNG 009 O Ring 9 90 BTW04 1 4 20 x 1 2 Wing Screw Black Opaque Dust Cover Support Channels FM2 Camera Bracket Pre Cut Liner OH121 161 201 Acrylic Dome Ceiling Grid not supplied IMPORTANT SAFEGUARDS 1 Read Instructions All the safety and operating instructions should be read before the unit is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the unit and in the operating instructions should be adhered to 4 Follow Instructions All operating amp user instructions should be followed 5 Electrical Connections Only a qualified electrician should make electrical connections 6 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards 7 Cable Runs All cable runs must be within permissible distance 8 Mounting This unit must be properly and securely mounted to a supporting structure capable of sustaining the weight of the unit Accordingly a Installation should be made by a qualified installer b Installation should be in compliance with local codes c Care should be exercised to select suitable hardware to install the unit taking into account both the composition of the mounting surface and the weight of the unit Be sure to periodically examine the unit and the supporting structure to make sure
5. chase and to establish warranty eligibility DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY AND OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312 3 OF THE UNIFORM COMMERCIAL CO DE AND OR IN ANY OTHER COMPARABLE STATE STATUTE VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON VIDEOLARM PRODUCTS OR NON VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM IF ANY AND PURCHASER S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER
6. ll labor and or parts charges The limited warranty stated in these product instructions is subject to all of the following terms and conditions 1 NOTIFICATION OF CLAIMS WARRANTY SERVICE If Purchaser believes that the Product is defective in material or workmanship then written notice with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period If after investigation Videolarm determines that the reported problem was not covered by the warranty Purchaser shall pay Videolarm for the cost of investigating the problem at its then prevailing per incident billable rate No repair or replacement of any Product or part thereof shall extend the warranty period as to the entire Product The specific warranty on the repaired part only shall be in effect for a period of ninety 90 days following the repair or replacement of that part or the remaining period of the Product parts warranty whichever is greater 2 EXCLUSIVE REMEDY ACCEPTANCE Purchaser s exclusive remedy and Videolarm s sole obligation is to supply or pay for all labor necessary to repair any Product found to be defective within the warranty period and to supply at no extra charge new or rebuilt replacements for defective parts 3 EXCEPTIONS TO LIMITED WARRANTY Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the warrant
7. on amp shipping instructions TECHNICAL SUPPORT Videolarm has set up a 24 hour technical support line for their customers 24 HOUR TECHNICAL SUPPORT 1 800 554 1124 VIDEOLARM INC warrants this Product to be free from defects in material or workmanship as follows PRODUCT CATEGORY PARTS LABOR All Enclosures and Electronics Three 3 Years Three 3 Years Pan Tilts Three 3 Years 6 months if used in autoscan Three 3 Years 6 months if used in autoscan Poles PoleEvators Three 3 Years Three 3 Years Warrior Q View 1 R Illuminators Five 5 Years Five 5 Years Controllers Three 3 Years Three 3 Years Power Supplies Three 3 Years Three 3 Years Accessory Brackets Three 3 Years Three 3 Years During the labor warranty period to repair the Product Purchaser will either return the defective product freight prepaid or deliver it to Videolarm Inc Decatur GA The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA Return Materials Authorization number displayed on the outer box or packing slip To obtain a RMA you must contact our Technical Support Team at 800 554 1124 extension 101 Videolarm will return the repaired Product freight prepaid to Purchaser Videolarm is not obligated to provide Purchaser with a substitute unit during the warranty period or at any time After the applicable warranty period Purchaser must pay a
8. that the integrity of the installation is intact Failure to comply with the foregoing could result in the unit separating from the support structure and falling with resultant damages or injury to anyone or anything struck by the falling unit UNPACKING Unpack carefully Electronic components can be damaged if improperly handled or dropped If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper Be sure fo save 1 The shipping carton and packaging material They are the safest material in which to make future shipments of the equipment 2 These Installation and Operating Instructions LIMITED WARRANTY ror vipEo arM INC PRODUCTS SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alertthe userto presence of important operating and maintenance servicing instructions in the literature accompanying the appliance SERVICE If the unit ever needs repair service customer should contact Videolarm 1 800 554 1124 for return authorizati
9. y period which is subjected to any of the following abuse improper use negligence accident lightning damage or other acts of God i e hurricanes earthquakes modification failure of the end user to follow the directions outlined in the product instructions failure of the end user to follow the maintenance procedures recommended by the International Security Industry Organization written in product instructions or recommended in the service manual for the Product Furthermore Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts based on usage and the end user has failed to follow such schedule attempted repair by non qualified personnel operation of the Product outside of the published environmental and electrical parameters or if such Product s original identification trademark serial number markings have been defaced altered or removed Videolarm excludes from warranty coverage Products sold AS IS and or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser All software and accompanying documentation furnished with or as part of the Product is furnished AS IS i e without any warranty of any kind except where expressly provided otherwise in any documentation or license agreement furnished with the Product 4 PROOF OF PURCHASE The Purchaser s dated bill of sale must be retained as evidence of the date of pur
Download Pdf Manuals
Related Search