Sharkoon Tauron Red Edition
Contents
1. also in extracts for translation reprinting reproduction by copying or other technical means Infringements will lead to compensation All rights reserved especially in case of assignation of patent or utility patent Means of delivery and technical modifications reserved Disposal of your old product Your product is designed and manufactured with high quality materials and components which can be recyc led and reused When this crossed out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002 96 EC Please be informed about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste The correct disposal of your old product will help prevent potential negative consequences to the envi ronment and human health SHARKOON Technologies 2011 www sharkoon com TAURON2. of a 3 5 device 1 Remove the case s front panel by gently pulling it towards you 2 Dismantle the 3 5 front bezel by removing it from the front panel fig 17 Fig 17 3 Unlock the quick fasteners which attach the mounting frame for 3 5 devices inside the case fig 18a and remove the mounting frame from the case fig 18b Fig 18b Carefully remove an optionally present metal bezel covering the 3 5 drive bay by using a gripper TAURON dharkoon 4 Place the 3 5 device into the mounting frame for 3 5 devices and attach the device to the frame from both sides fig 19 Fig 19 5 Slide the mounting frame with the installed 3 5 device into the case s mounting bay fig 20a and lock it from both sides using the quick fasteners fig 20b vela ie Fig 20a Fig 20b 6 Connect the 3 5 device to the power supply and the mainboard 7 Replace the front bezel to the case TAURON dharkoon 11 Installation of an add on card 1 Remove the anchor screw of the slot bezel and take it from the case 2 Insert the add on card into the respective slot of the mainboard and attach it to the case using the anchor screw fig 21 Fig 21 3 Close the case 12 The pre installed fans using the fan control The pre installed fans provide a 3 pin as well as a 4 pin power connector A 3 pin power connector B 4 pin power connector The 3 pin power connec
3. Mharkoow hogy e D lt eg i WELL ec Nate 1 Beer REFEREE li Bee rid T MEFR HH E RFE a OATATE TAURON dharkoon Content 1 Features 3 2 Package content 3 3 The case at a glance 4 4 Installation notes 8 5 Rebuilding the HDD cages 9 6 Installation of a mainboard 11 7 Installation of a PSU 14 8 Installation of a HDD 15 9 Installation of an optical device 17 10 Installation of a 3 5 device 19 11 Installation of an add on card 21 12 The pre installed fans using the fan control 21 13 Installation of additional fans optimized airflow 22 Dear customer Congratulations for purchasing this premium quality SHARKOON product For a long life time and to take full advantage of this product we recommend you to read this manual completely Enjoy our product SHARKOON Technologies TAURON dharkoon 1 Features e ATX case e 2x 5 25 drive bays external e 1x 5 25 or 3 5 drive bays external e 7x 2 5 or 3 5 bays with removable mounting trays for HDDs internal e Top I O 2x USB3 0 2x USB2 0 and 2x audio power and reset button 2x fan speed controllers for up to 6 fans e 7 slots for add on cards e Acrylic side panel Plastic front panel with air inlet drive bay covers in mesh design e Quick fasteners for optical drives mainboard mounting with installation opening for CPU coolers e 4 openings for water cooling e Cable manageme
4. e respective bottom fitting of the case until the attachment lever locks fig 2a and b i Hii li i AIITIYY MIT JITA T 78 ALITYT AAA O IIT J i A L IIT fig 2a TAURON dharkoon 6 Installation of a mainboard 1 Unscrew the thumb screws on the back side of the case and remove both side panels Lay down the case sidewise on an even surface 2 The mounting panel of the mainboard inside the case provides various mounting holes to fix the standoffs fig 3 T Fig 3 The mainboard contains special screw mounts fig 4 Fig 4 TAURON dharkoon Place the mainboard to the mounting panel A standoff must be screwed into every hole on the mounting panel visible through the mainboard s screw openings 3 Remove the mainboard and screw the standoffs into the their respective holes on the mounting panel fig 5 Fig 5 4 Insert the I O shield delivered with the mainboard into the I O shield opening in the rear panel of the case TAURON dharkoon 5 Place the mainboard back onto the standoffs and screw the mainboard to them fig 6 Fig 6 6 Plug the connectors of the case s front bezel to the respective connectors of the mainboard please refer to your mainboard s manual for further information TAURON dharkoon 7 Installation of a PSU 1 Position the case in front of you and from the inside pos
5. ers b Cable feedthrough dharkoon Top panel Bottom panel A Case feet B Air inlet for PSU C Fan bracket for 120 mm or 140 mm fan TAURON A On off button B Top l O a 2x USB3 0 b 2x audio c Reset button d 2x USB2 0 e 2x fan control C under the mesh bezel 170 mm fan dharkoon The internal I O connectors A Audio connectors for a HD Audio b AC 97 USB2 0 connector 2x USB3 0 connectors Fan control connector Front l O power connector Connectors for Power Switch Power LED Power LED HDD LED Reset Switch 1m O DO QOI 4 Installation notes 1 For further information on how to install the PC components please also refer to their respective instructions 2 In order to guarantee full functionality of the fan controls and the front connectors the front l O power connector must be connected to the power supply TAURON dharkoon 5 Rearranging the HDD cages The HDD cages of the case may be re arranged so that VGA cards up to 42 cm can be installed e E i ti oe ie a 1 EN PN E 3 E LH Alternative HDD cage arrangements dharkoon In order to remove the HDD cages proceed as follows Unscrew the thumb screws on the back side of the case and remove both side panels fig 1b 1 fig 1b fig 1a 3 Slide the HDD cage into th
6. ition the PSU against the PSU bracket on the case s rear panel fig 7 Fig 7 2 Screw the PSU to the case from the outside fig 8 Screws for PSU mounting Fig 8 TAURON dharkoon 8 Installation of a HDD Fig 9 Mounting frame 2 Place an HDD into the mounting frame connectors pointing backwards fig 10a and b Fig 10a Fig 10b TAURON dharkoon 3 Attach the HDD to the mounting frame from below fig 11a and b Fig 11a Fig 11b 4 Slide the mounting frame into the HDD cage until it locks fig 12 r l at A Fa gt b b TET Fig 12 5 Connect the HDD to the PSU and the mainboard TAURON dharkoon 9 Installation of an optical device 1 Remove the case s front panel by gently pulling it towards you fig 13 2 Dismantle the 5 25 front bezel from the mounting bay by removing it from the front panel fig 14 Fig 14 TAURON dharkoon 3 Place the front panel back onto the case 4 Slide the optical drive into the case s drive bay fig 15 Fig 15 5 Attach the optical device to the case from both sides using the quick fasteners fig 16 Fig 16 Note If you intend to transport the case we recommend that you screw in the built in devices additionally 6 Connect the optical drive to the power supply and the mainboard TAURON dharkoon 10 Installation
7. nt system Interior painting Removable HDD brackets support long VGA cards up to 42 cm e Fan configuration 2x 120 mm LED fan pre installed 1x 120 mm fan pre installed Top panel 1x 170 mm fan pre installed Dimensions 510 x 205 x 495 mm L x W x H Weight 9 5 kg 2 Package contents e ATX case Tauron e Manual flyer e Accessory kit Note If you are missing any of the items listed above please contact our customer service immediately support sharkoon com Germany and Europe support sharkoon com tw international TAURON dharkoon 3 The case at a glance Front panel A 5 25 drive bays B 3 5 mounting bay C behind the mesh panel 2x 120 mm LED fans Side panel closed left A Acrylic side panel TAURON dharkoon Side panel opened left A Mainboard mounting panel a Installation opening for CPU coolers b Cable feedthrough 5 25 drive bays 3 5 mounting bay Quick fasteners HDD cages moO WwW Side panel closed right A Air inlet for CPU B Air inlet for HDDs TAURON dharkoon Side panel opened right moov Rear panel Opening for I O shield Openings for water cooling 120 mm fan Slot bezels PSU bracket moov TAURON 5 25 drive bays 3 5 mounting bay Quick fasteners HDD cages Mainboard mounting panel a Installation opening for CPU cool
8. tor lets you connect the respective fan to a matching power connector of the main board in this case the fan will be controlled by the mainboard or a connector of the case s fan control in this case the fan speed can be adjusted by using the sliders of the fan controller dh TAURON dharkoon Fan connector of the fan control Sliders of the fan control 13 Installation of an additional bottom panel fan optimized airflow The case provides the opportunity to install an additional 120 or 140 mm fan into the bottom panel Therefore proceed as follows 1 Remove the bottom fitting for the HDD cages by loosening its four mounting screws und removing the fitting from the case fig 23 sA Z 4 ee i a N a a oe ee ee R SS a a ae ee TAURON dharkoon 2 Place the fan against the respective bracket from the inside of the case 3 Screw the fan to the attachment from the outside 4 Connect the fan to the mainboard or the PSU Notes When installing fans make sure that cool air is taken in on the front bottom of the case and blown out on its rear side top The PC components with the highest heat development should be placed directly within the airflow Legal disclaimer As a continuing policy of product improvement at SHARKOON the design and specifications are subject to change without prior notice National product specifications may vary All rights reserved especially
Download Pdf Manuals
Related Search