Home
Olympia A 235
Contents
1. 52 Koudlamineren 1 Steek de netstekker in een goed bereikbaar stopcontact Let op Controleer of de voedingsspanning die op het apparaat vermeld staat overeenkomt met die van het elektriciteitsnet 220 240 V 50 Hz 2 Schakel de Aan Uit schakelaar aan de rechterbovenkant van het apparaat in 1 3 De aandrijfmotor voor de transportrollen begint te draaien het rode signaallampje POWER en het groene signaallampje READY lichten op Let op Hebt u het lamineerapparaat kort van tevoren gebruikt voor heetlamineren dan moet u het laten afkoelen De afkoelingstijd duurt maximaal 30 minuten 4 Verwijder de beschermfolie van het lamineerhoesje 5 Leg het te lamineren voorwerp zodanig in het lamineerhoesje dat aan alle kanten 3 5 mm afstand tot de folierand overblijft 6 Steek de folie samen met het te lamineren voorwerp in de invoeropening van het lamineerapparaat De gesloten kant van de folie moet het eerst in het apparaat worden ingevoerd gt Opmerking Om vouwen in de lamineerfolie te voorkomen mag nooit de open kant van de lamineerfolie als eerste in de invoeropening van het lamineerapparaat worden gestoken Bij het invoeren van de folie beslist de instructies op de invoeropening opvolgen Het lamineerproces verloopt automatisch Klem zitttende folie losmaken Dit lamineerapparaat biedt de functie Jam Release om klem zittende folie snel te kunnen losmaken 1 Bij het blokkeren van folie het apparaat uitsc
2. f hrschlitz beachten Der Laminiervorgang erfolgt automatisch A Achtung Die austretende Folie ist nach dem Laminieren sehr hei und weich Daher mit dem laminierten Produkt vorsichtig umgehen gt Hinweis Zum Ebnen kann das laminierte Produkt mit einem Buch oder einem anderen schweren ebenen Gegenstand gepresst werden 10 Kaltlaminieren 1 SchlieRen Sie das Stromkabel an eine gut zugangliche Standard steckdose an A Achtung Pr fen Sie ob die Spannungsangabe des Gerates mit der Ihres Stromnetzes bereinstimmt 220 240 V 50 Hz 2 Schalten Sie den Ein Aus Schalter an der rechten Ger teoberseite ein I 3 Der Antriebsmotor f r die Transportrollen l uft an die rote Anzeige leuchte POWER und die gr ne Anzeigeleuchte READY leuchten A Achtung Haben Sie das Laminierger t kurz vorher zum Hei lami nieren eingesetzt m ssen Sie das Laminierger t abk hlen lassen Die Ab k hlzeit dauert bis zu 30 Minuten 4 Entfernen Sie die Schutzfolie von der Folientasche 5 Legen Sie das Laminiergut in die Folientasche so ein dass allseitig etwa 3 bis 5 mm Abstand vom Folienrand vorhanden ist 6 F hren Sie die Folie zusammen mit dem Laminiergut in den Einf hr schlitz des Laminierger tes ein Die geschlossene Seite der Folie ist hierbei zuerst einzuf hren gt Hinweis Um ein Falten der Laminierfolie zu vermeiden darf nie die offene Seite der Laminierfolie zuerst in den Einf hrschlitz des Laminierger tes e
3. Komponenten Zubeh r technische Spezifikationen sowie die hier vorliegende Dokumenta tion des Produktes ohne vorherige AnkUndigung jederzeit zu andern Bestimmungsgem e Verwendung Mit diesem Laminiergerat k nnen Hei laminierfolien und Kaltlaminierfolien bearbeitet werden Es k nnen Bilder Karten Dokumente Papier usw bis zu einer Gesamtdicke von 0 5 mm laminiert werden Jede andere Verwendung gilt als nicht bestimmungsgem Eigenm chtige Ver nderungen oder Umbauten sind nicht zul ssig bersicht 0 Folienstau beheben Jam Release Schalter Kalt Hei laminieren Linke Schalterstellung Kaltlaminieren Mittlere Schalterstellung Hei laminieren 80 um Rechte Schalterstellung Hei laminieren 125 um EIN AUS Schalter ON OFF Rote LED Power Ger t eingeschaltet Gr ne LED READY Ger t bereit Einf hrschlitz Oo 6060 Ausgabeschlitz Leistungsmerkmale Schutz und Veredelung f r Ihre Dokumente Laminiert Fotos Dokumente Grafiken Ausweise usw bis Gr e DIN A4 Das Gerat arbeitet mit 4 Heizwalzen hat eine schnelle Aufw rmzeit und la miniert ohne Tr ger e 2 LED Lampen zeigen die Betriebszust nde an e Automatische Abschaltung bei berhitzung e Hochwertiges Heizsystem verhindert Schlieren und Blasenbildung e Aufw rmzeit nur ca 5 Minuten e Abk hlzeit auf Zimmertemperatur ca 30 Minuten e Folienst rke von mindestens 80 um und maximal 125 um Laminiersystem Ho
4. Laminiergerat A 235 entschie den haben Sollte sich an Ihrem Gerat wider Erwarten ein technisches Prob lem ergeben beachten Sie bitte folgende Punkte e Die Garantiezeit f r Ihr Ger t betr gt 24 Monate e Bewahren Sie unbedingt den Kaufbeleg und die Originalverpackung auf e Sollte ein Problem auftreten rufen Sie bitte zuerst unsere Hotline an 0180 5 007514 0 14 Minute Oft kann unser Fachpersonal telefonisch helfen e Kann jedoch der Fehler telefonisch nicht beseitigt werden bitten wir Sie das Ger t in der Original Verpackung an folgende Anschrift zu senden Service Center Hattingen Weg zum Wasserwerk 10 45525 Hattingen Garantiereparaturen k nnen nur mit beigef gtem Kaufbeleg erfolgen Herzlichen Dank fur Ihr Verstandnis Mit freundlichen Gr en Ihre Olympia Business Systems Vertriebs GmbH 13 Important Safety Information GB Please observe the following information to ensure reliable operation of the laminator 1 2 10 11 12 13 14 15 16 17 18 19 Read this manual thoroughly and observe the instructions and information in it when operating the unit Keep the operating instruction manual available for future refer ence Prevent damage to the power plug and power cable Never twist the power cable Do not operate the unit if the power cable or power plug is damaged Do not use the unit in the vicinity of hot surfaces or in damp environments and protect it from direct sunli
5. No utilice el aparato ceca de superficies calientes o en un entorno humedo y proteja el mismo frente a la radiaci n solar directa y fuertes efectos de polvo Antes de la limpieza del aparato siempre se deba sacar la clavija de red No utilice disolventes o agentes de limpieza agresivos No se pueden laminar objetos met licos Para nifios esta prohibida la estancia en el area de trabajo de la maquina en disposici n de servicio En caso de no utilizaci n del aparato se debe sacar la clavija de red Se debe desconectar el aparato inmediatamente cuando se percibe un olor penetrante o cuando el aparato no se encuentra en servicio Con las manos h medas no se debe entrar en contacto con la clavija de red Aseg rese de que el interruptor de conectado desconectado se encuentra en la posici n OFF antes de conectar el aparato laminador a la red de corriente En el aparato s lo se deben introducir fundas de pel cula transparente previstas seg n las indicaciones del punto Caracter sticas prestacionales Unas fundas de pel cula transparente excesivamente grandes pueden originar atascos de pel cula transparente No lamine materiales termosensibles como por ejemplo papel t rmico con este aparato Al laminar documentos h medos no se consiguen buenos resultados de laminaci n Para la laminaci n en caliente no debe utilizar fundas de pel cula transparente previstas para la laminaci n en fr o En tal caso la maquina
6. et des restes de colle sur les rouleaux de transport peuvent in fluencer le r sultat de la plastification C est pourquoi les rouleaux de trans port doivent tre nettoy s p riodiquement apr s l emploi A cet effet introduire une feuille de papier pli e dans la fente d introduction Les restes de colle seront emport s par le papier sortant R p ter plusieurs fois l op ration Retirez toujours la prise de secteur avant d effectuer un nettoyage humide de l appareil Si n cessaire le bo tier peut tre nettoy avec un savon doux et un chiffon tremp dans de l eau claire N utilisez jamais de solvants ou de produits d entretien agressifs Elimination d erreurs Erreurs Solutions e Le voyant DEL rouge POWER ne Contr lez si le c ble lectrique a s allume pas t correctement mis dans la prise e L appareil ne r agit pas de courant standard e Si l erreur n a pas t limin e adressez vous notre hotline e Bourrage par les feuilles de plasti E e Contr lez la taille de la poche de que i plastique utilis e e N utilisez que des poches de plas tique de la taille indiqu e e Assurez vous que la poche de plastique a t introduite bien droite dans l appareil e Pour liminer le bourrage suivez les instructions donn es au point Elimination de bourrage e La feuille plastifi e n est pas par e Plastifiez cette feuille une nouvelle faitement transparente fois pour am liorer le r su
7. is reached after about 5 minutes 80 um 6 minutes 125 um and the green indicator lamp READY lights up 4 Insert the document to be laminated in the pouches so that there is a margin of approx 3 5 mm to the edge of the foil on all sides A Caution Only use foil intended for hot laminating 5 Insert the foil containing the document in the laminator s insertion slot Insert the ready closed side of the pouch first Note To prevent the laminating foil from creasing never insert the open end of the foil pocket in the insertion slot of the laminator first When inserting the foil observe the instructions on the insertion slot The laminating process occurs automatically A Caution The foil is very hot and soft when ejected following lamina tion Therefore handle the laminated product with extreme care Note To flatten the laminated product place a book or similar heavy flat object on it 18 Cold Laminating 1 Connect the power cable to an easily accessible standard electrical socket A Caution Check that the voltage specifications of the unit correspond to that of your power supply network 220 240 V 50 Hz 2 Switch on the On Off switch on the top right hand side of the unit 1 3 The drive motor for the transport rollers starts up the red and green indicator lamps POWER and READY respectively light up A Caution If the laminator was switched to hot laminating shortly before allow it to cool dow
8. k t n s e jste se rozhodli pro tento p stroj V p pad vzniku z vady odevzdejte p stroj spolu s pokladni n m dokladem a origin ln m obalem v prodejn kde jste p stroj zakoupili 63 Konformit tserkl rung Declaration of Conformity DoC Nr 3111 Rev 00 gemaB der Richtlinie 2004 108 EG und der Richtlinie 2006 95 EG in accordance with the Directive 2004 108 EEC and the Directive 2006 95 EEC OLYMPIA Business Systems Vertriebs GmbH Hersteller Verantwortliche Person The manufacturer responsible person erklart dass das Produkt declares that the product Laminator A 235 bei bestimmungsgemaBer Verwendung den grundlegenden Anforderungen entspricht complies with the essential requirements when used for its intended purpose Schutzanforderungen in Bezug auf die elektromagnetische Vertr glichkeit und die Niederspannungs richtlinie Protection requirements concerning Electromagnetic Compatibility and Low Voltage Directive Angewendete harmonisierte Normen EN 55014 1 2006 Harmonised standards applied EN 55014 2 A1 2001 EN 61000 3 3 1995 A2 2005 EN 61000 3 2 2006 EN 60 950 1 2006 Anschrift Olympia Business Systems Vertriebs GmbH Address Weg zum Wasserwerk 10 45525 Hattingen Phone 02324 6801 0 Fax 02324 6801 97 E mail tr de Hattingen 24 M rz 2010 Heinz Prygoda y a Es Ee GENEE Place amp date of issue Name and signature 65 Diese Bedienungsanleitung dient de
9. kdykoliv zm nit a to bez p edchoz ho ozn men komponenty p slu enstv technick specifika ce jako i zde p edlo enou dokumentaci k v robku Pou it p stroje odpov daj c jeho p vodn mu ur en S t mto lamin torem Ge zpracov vat f lie jak za tepla tak i za studena Lze laminovat obr zky vizitky dokumenty pap r atd s max tlou kou 0 5 mm Jak koliv jin pou it se pova uje za pou it neodpov daj c elu Sv voln prov d n zm n nebo p estaveb nen p pustn 57 Prehled 0 Odstran n nakupen f lie Jam Release P ep na laminov n za studena za tepla poloha p ep na e vlevo laminov n za studena st edn poloha p ep na e laminov n za tepla 80 um poloha p ep na e vpravo laminov n za tepla 125 um P ep na ZAP VYP ON OFF erven kontrolka LED Power p stroj zapnut Zelen kontrolka LED READY p stroj p ipraven Vstupn t rbina Oo 6060 V stupn t rbina 58 Vykonnostni znaky Ochrana a zlep en vlastnost Va ich dokument Laminuje fota dokumenty grafiky pr kazy atd do velikosti form tu DIN A4 P stroj pracuje se 4 v h evn mi v le ky rychle se zah v a laminuje bez nosi e e 2 kontrolky LED ukazuj provozn stav e Automatick vypnut p i p eh t e Vysoce kvalitn zah vac syst m znemo uje vytvo en mouh a bublin e Doba za
10. lamin toru o istit tkaninou p edem namo e nou v ist vod s jemn m m dlem Nepou vejte dn rozpou t dla ani agresivn ist c prost edky Odstran n z vady Z vada e en e erven kontrolka LED POWER nesv t P stroj nereaguje Zkontrolujte zda je s ov kabel spr vn zastr en do standardn z suvky Pokud nebyla z vada odstran na obra te se na na i horkou linku e Nakupen f lie e Laminovac f lie nen dokonale pr hledn P ekontrolujte velikost pou van f lie Pou vejte pouze f lie uveden velikosti Ujist te se zda byla f lie zasunuta do p stroje rovn K odstran n nakupen postupujte podle pokyn uveden ch v odstav ci Odstran n nakupen f lie Zopakujte postup laminov n s tout f li abyste dos hli lep ho v sledku Pou v te li tlust j f lii 100 um 125 um nechte p stroj d le zah t CE 62 Soulad se sm rnicemi EU potvr zuje znaceni CE Pokyny k likvidaci Tento symbol p e krtnut n doba na odpad znamen e je u ivatel povinen odevzdat v robek ur en k likvidaci na dostupn m sb rn m m st nebo m st s t d n m odpadem Tento symbol plat pouze ve st tech EHP EHP Evropsk hospod sk prostor do n ho jsou MU zahrnuty lensk st ty EU a st ty Norsko Island a Lichten tejnsko Z ruka V en z kazn
11. s kaarten documenten papier enzovoort tot een totale dikte van 0 5 mm worden gelamineerd Elk ander gebruik is in strijd met de voorschriften Eigenmachtige wijzigingen of ombouw zijn niet toegestaan 49 Overzicht 0 Vastgelopen folie losmaken Jam Release Schakelaar Koud Heetlamineren Schakelaar in linkerstand koudlamineren Schakelaar in middelste stand heetlamineren 80 um Schakelaar in rechterstand heetlamineren 125 um AAN UIT schakelaar ON OFF Rode led Power Apparaat ingeschakeld Groene led READY Apparaat gereed Invoeropening 909090 Uitvoeropening 50 Kennmerken Bescherming en veredeling van uw documenten Lamineert foto s documenten grafieken pasjes enzovoort tot formaat DIN A4 Het apparaat werkt met 4 verwarmingsrollen heeft een korte opwarmtijd en lamineert zonder drager 2 LED s signaleren de bedrijfsstatus Automatische uitschakeling bij oververhitting Hoogwaardig verwarmingssysteem voorkomt vorming van rimpels of bellen Opwarmtijd slechts 5 minuten Afkoelingstijd tot kamertemperatuur ongeveer 30 minuten Dikte van de folie minimaal 80 um en maximaal 125 um Lamineersysteem Hotrol techniek 4 transportrollen Maximale lamineerbreedte 230 mm Maximale lamineerdikte 0 5 mm Lamineersnelheid 0 3 m min Voedingsspanning 220 240 volt 50 Hz Opgenomen stroom 1 55 A 345 W Afmetingen I x b x h 380 x 160 x 36 mm Gewicht ca 1175g 51 Heetlamineren 1 S
12. t ouvert de la feuille de plastique dans la fente d in troduction de la machine Tenez compte des instructions donn es au niveau de la fente d introduction quand vous introduisez la feuille de plastique L op ration de plastification se fait automatiquement A Attention La feuille de plastique sortante est tres chaude et molle apr s la plastification C est pourquoi il faut manier prudemment le produit plastifi gt Remarque Afin d aplanir le produit plastifi on peut presser celui ci sous un livre ou sous un autre objet plat et lourd 26 Plastification froid 1 Branchez le c ble lectrique dans une prise de courant standard facile d acc s A Attention Contr lez si les donn es relatives a la tension de l appa reil correspondent bien a celles de votre r seau 220 240 V 50 Hz 2 Branchez l interrupteur Marche Arr t situ sur le c t sup rieur droit de l appareil 1 3 Le moteur d entra nement des rouleaux de transport tourne le voyant lumineux rouge POWER et le voyant lumineux verte READY s al lument A Attention Si vous venez d utiliser la machine plastifier pour plasti fier a chaud vous devez la faire refroidir Le temps de refroidissement est de 30 minutes au maximum 4 Retirez la feuille de protection de la poche de plastique 5 Introduisez le mat riau a plastifier dans la poche de plastique de ma ni re ce que de tous les c t s il y ait une marge d env 3 5 mm par rap
13. Laminovac f lie nesm b t nikdy zasunuta do vstupn t rbiny p stroje otev enou stranou jinak by do lo k jej mu zvr sn n P i zasunut f lie respektujte pros m pokyny uveden na vstupn t rbin La minov n prob hne automaticky A Pozor Vysunut f lie je po zalaminov n velmi hork a m kk Za ch zejte proto se zalaminovan m v robkem opatrn IS Upozorn n Povrch zalaminovan ho v robku Ge vyrovnat za t en m knihou nebo jin m t k m ploch m p edm tem 60 Laminov ni za studena 1 Zapojte sitovy kabel do snadno dostupn standardni zasuvky A Pozor P esv d te se e daje o nap jen p stroje se shoduj s daji Va el s t 220 240 V 50 Hz 2 Zapn te p ep na Zap V p na prav horn stran p stroje I 3 Hnac motor posouvac ch v le k se spust erven kontrolka POWER a zelen kontrolka READY sv t Pozor Pokud jste kr tce p edt m pou ili p stroj k laminov n za te pla mus te nechat p stroj vychladnout Doba vychladnut trv a 30 minut 4 Odstra te z f lie ochrannou f lii 5 Vlo te materi l ur en k laminov n do laminovac f lie tak aby z stal na v ech stran ch zachov n asi 3 a 5 mm odstup od okraje f lie 6 Zasunte f lii sou asn s laminovac m materi lem do vstupn t rbiny p stroje F lii zasu te uzav enou stranou nap ed gt Upozorn n Laminovac f lie n
14. OLYMPIA G DADC Laminierger t GB GE CY Laminator ER EB Ch Plastifieuse Es Aparato laminador MEA Plastificatrice NDED Lamineerapparaat CZ Lamin tor Olympia Business Systems Vertriebs GmbH Weg zum Wasserwerk 10 D 45525 Hattingen http www olympia vertrieb de 15 04 2010 n OLYMPIA A 235 Deutsch DEDEH Wichtige Sicherheitsanweisungen cnn naar rca 6 Empfehlung vicio on AA Re 7 Haftungsausschluss ci 7 Bestimmungsgem e Verwendung cnn n nennen ernennen 7 bersicht inver EL aaa lan 8 Leistungsmerkmale cuicos iia 9 Ean Lel Tg race a 10 Kaltlaminieren 2 ee es i alii 11 Foliensta behebeni ur un e u 4eRH nenne 11 Pflege und Reinigung nn 12 Fehlerbehebung posed Hamann 12 Entsorg ngshinW8lS sinned iaia iaia 13 Garantie mamsie nn A ee see 13 English GBGEXGY Important Safety Information rn nennen ran 14 RecoMMendatiON cisco ini osten ms 15 Exemption From Liability ss 15 Intended WEE 15 OVEFVISW crea notar 16 Features A A Gre 17 Hot Laminating viii EE 18 Gold kaminaling tia aa 19 Clearing Foil Jams u ara en ee 19 Cleaning and Servicing sieste 20 TPOUDIESHOOUNG EE 20 Disposal Notes salita bilie dilata ihn 21 ELE AEREO OI O 21 Fran ais FR6BCH Consignes importantes de s curit 22 Kell E ue BEE Exclusion de la garantie Utilisation conforme aux prescrip
15. ave y agua transparente No utilice disolventes o agentes de limpieza agresivos 36 Eliminacion de fallos Error 000000 _Soluciones i e EI LED rojo POWER no se e Compruebe si el cable de Seege ilumina est correctamente enchufado en e El aparato no reacciona la caja de enchufe est ndar i e Si no ha sido posible eliminar el error rogamos se ponga en contacto con nuestra linea de asistencia telef nica e Atasco de peliula transparente e Compruebe el tama o de la funda de pelicula transparente utilizada Utilice s lo fundas de pel cula transparente del tama o indicado e Aseg rese de que la funda de pel cula transparente haya sido introducida de forma recta en el aparato Siga las instrucciones que figuran en el punto Eliminar un atasco de pel ula transparente para eliminar el atasco e La pel cula transparente laminada Vuelva a laminar la misma pel cula no es completamente transparente transparente para mejorar el resultado de laminaci n Si se utiliza una pel cula transpar ente de mayor espesor 100 um 125 um se debe dejar el aparato calentando durante m s tiempo La conformidad con las directivas de la UE queda afirmada mediante el s mbolo CE 37 Indicaci n sobre la eliminaci n de residuos Este s mbolo imagen de un cubo de basura tachado significa que el producto deberia ser llevado a los sistemas de recogida dispuestos para los usuarios finales c
16. avo di rete dell apparecchio devono essere facilmente accessibili per poter disinserire l alimentazione elettrica in caso d emergenza 19 Impiegare l apparecchio solo in ambienti chiusi asciutti Consiglio Se si tratta di plastificare materiali molto morbidi come tovaglioli di carta o formati particolarmente piccoli si consiglia di posizionare l oggetto da plasti ficare tra un ulteriore foglio di carta ripiegata allo scopo di evitare intasamen ti Rivolgere in tal caso il foglio con la piegatura verso la plastificatrice Carte d identit e documenti possono perdere la loro validit in caso di pla stificazione visto che l autenticit del documento non cosi pi verificabile n caso di cessione del prodotto ad un altra persona si prega di corredare sempre l apparecchio con le presenti istruzioni per l uso Esclusione di responsabilit Non si assume nessuna garanzia per l esattezza delle informazioni che fanno riferimento alle caratteristiche tecniche ed alla presente documentazione allegata II prodotto descritto in questa documentazione ed i suoi accessori e ventualmente necessari sono soggetti a continue migliorie e sviluppo Per tale motivo ci riserviamo il diritto di modificare in qualsiasi momento e senza preavviso alcuno componenti accessori specifiche tecniche e la qui pre sente documentazione del prodotto Impiego conforme alle disposizioni Con questa plastificatrice possibile applicare pellicole per plas
17. azione Effettuare quindi periodicamente una pulizia dei rulli di trasporto dopo l utilizzazione A questo scopo inserire nella fessura di inserimento un foglio di carta ripie gato residui di adesivo vengono asportati dal foglio di carta in uscita Ripe tere pi volte il procedimento Staccare sempre la spina di alimentazione prima di inumidire l apparecchio per pulirlo Qualora necessario la custodia pu essere pulita con un panno inumidito in sapone neutro ed acqua pulita Non utilizzare solventi o deter genti aggressivi 45 Soluzione di problemi Problema _ e Spia LED rossa POWER non si i accende pi Apparecchio non reagisce e Intasamento da pellicola e Pellicola plastificata non comple tamente trasparente CE e Controllare il corretto inserimento Soluzione del cavo elettrico nella presa stan dard e Nel caso di mancata soluzione del problema rivolgersi alla nostra hotline e Verificare la dimensione della pel licola per plastificazione utilizzata e Impiegare solo pellicole per plasti ficazione nelle dimensioni indicate e Assicurarsi che la pellicola di pla stificazione sia stata appena inse rita nell apparecchio e Per rimuovere l intasamento se guire le istruzioni riportate al punto Rimuovere l intasamento da pelli cola e Sottoporre a plastificazione la stessa pellicola al fine di migliorare il risultato della plastificazion
18. crito en la presente documentaci n y en caso dado sus accesorios est n sujetos a la mejora continua y al desarrollo ulterior Por este motivo nos reservamos el derecho de modificar en cualquier momento y sin previa notificaci n los componentes accesorios especificaciones t cnicas as como la presente documentaci n del producto Uso previsto Con este Aparato laminador se pueden procesar pel culas transparentes de laminaci n en caliente y pel culas transparentes de laminaci n en fr o Se pueden laminar figuras tarjetas documentos papel etc hasta un espesro total de 0 5 mm Cualquier otro uso se considera no conforme al objetivo previsto Se prohibe expresamente cualquier modificaci n o transformaci n 31 Vista general 0 Eliminar un atasco de pelicula transparente Jam Release Interruptor para laminaci n en frio caliente Posici n de interruptor izquierda Laminaci n en frio Posici n de interruptor central Laminaci n en caliente 80 um Posici n de interruptor derecha Laminaci n en caliente 125 um Interruptor CON DES ON OFF LED rojo Power aparato encendido LED verde READY aparato preparado Ranura de entrada Oo 6060 Ranura de salida 32 Caracteristicas prestacionales Protecci n y mejora de sus documentos Para laminar fotos documentos graficos Documentos Nacionales de Identidad etc hasta un tama o maximo de DIN A4 El aparato trabaja con 4 rodillos calefac
19. dena T mto by do lo k po kozen p stroje laminovac f lie i dokumentu 16 Nezast ih vejte laminovac f lie Vznikl ezn hrany mohou zp sobit nakupen f lie 17 Udr ujte voln sou sti od vu kravaty perky dlouh vlasy nebo jin voln p edm ty v bezpe n vzd lenosti od vstupn ho otvoru Nebezpe zran n 56 18 Z suvka a s ov p pojka p stroje mus b t z bezpe nostn ch d vod voln p stupn aby mohla b t v p pad nouze rychle odpojena dod vka elekt iny 19 P stroj se sm pou vat pouze v such ch uzav en ch prostor ch Doporu en Pokud chcete laminovat velmi m kk materi ly jako nap ubrousky nebo mal form ty pak doporu ujeme abyste laminovan materi l nav c vlo ili do p elo en ho listu pap ru a t m zabr nili nakupen f lie Tento laminovan ma teri l mus te do p stroje zasunout uzav enou stranou Pr kazy a dokumenty mohou laminov n m pozb t platnost proto e n sledn p ezkou en jejich pravosti nen mo n V p pad e p ed te lamin tor jin osob p ilo te k n mu pros m v dy ten to n vod k obsluze Nep eb r me dnou z ruku za spr vnost informac kter se t kaj tech nick ch vlastnost a zde p edlo en dokumentace V t to dokumentaci popsan v robek respektive jeho p slu enstv jsou neust le zlep ov ny a d le vyv jeny Z tohoto d vodu si vyhrazujeme pr vo
20. des mat riaux tr s souples tels que serviettes en papier ou des petits formats doivent tre plastifi s nous recommandons de les placer dans une feuille de papier pli e en vue d viter d ventuels bourrages Les introduire dans la plastifieuse le bord de pliage en avant Les pi ces d identit et les documents peuvent perdre leur validit lorsqu ils sont plastifi s car leur authenticit ne peut plus tre v rifi e Au cas o vous d sireriez transmettre ce produit une autre personne veuil lez ne pas oublier de joindre ce mode d emploi Exclusion de la garantie Nous n assurons pas de garantie en ce qui concerne l exactitude des infor mations qui se rapportent aux propri t s techniques ainsi qu la pr sente documentation Le produit d crit dans cette documentation et le cas ch ant ses accessoires sont soumis une am lioration et un perfection nement technique constants Pour cette raison nous nous r servons le droit de modifier tout moment et sans annonce pr alable les composants les accessoires les sp cifications techniques ainsi que la documentation pr sente du produit Utilisation conforme aux prescriptions Cette machine plastifier permet de traiter des feuilles de plastification chaud et des feuilles de plastification froid Des images des cartes des documents du papier etc d une paisseur totale de 0 5 mm max peuvent tre plastifi s Tout autre utilisation est consid r
21. e e Utilizzando pellicole pi spesse 100 um 125 pm prolungare la durata di riscaldamento dell apparecchio La conformit con le normative EU viene confermata dal marchio CE 46 Indicazione sopra l eliminazione dei rifiuti Questo simbolo significa che il prodotto giunto a fine vita dovrebbe essere conferito ai punti di raccolta differenziata a disposizione dell utente finale Questo simbolo si applica ai paesi aderenti all EEA EEA Europea Economic Area che MM comprende gli stati membri dell EU compresi Norvegia Islanda e Liechtenstein Garanzia Caro cliente ci congratuliamo con Lei per aver scelto questo apparecchio In caso di difetti La preghiamo di ritornare l apparecchio completo di imballo originale e scontrino di acquisto al punto vendita dove stato effettuato l acquisto 47 Belangrijke veiligheidsinstructies ND Neem het volgende in acht om er zeker van te zijn dat u het lamineerapparaat correct gebruikt 1 2 3 10 11 12 13 14 15 16 17 Lees deze instructies aandachtig door en volg ze op bij het gebruik van het apparaat Gebruiksaanwijzing voor toekomstig gebruik bewaren Beschadiging van netstekker en netsnoer voorkomen Netsnoer niet laten opkrullen Het apparaat niet in gebruik nemen als het netsnoer of de stekker beschadigd is Gebruik het apparaat niet in de buurt van hete opperviakken of in een vochtige omgeving en bescherm het tegen directe zon
22. e comme non conforme son usage II n est pas permis d apporter des modifications et des transfor mations sans concertation pr alable 23 Vue d ensemble 0 Eliminer le bourrage de pochette Jam Release Interrupteur plastification froid chaud Position de l interrupteur gauche plastification froid Position de l interrupteur centrale plastification chaud 80 um Position de l interrupteur droite plastification chaud 125 um Interrupteur MARCHE ARRET ON OFF LED rouge Power Appareil allum LED verte READY Appareil pr t a fonctionner Fente d insertion Oo 6060 Fente de sortie 24 Caract ristiques de performance Protection et fa onnage de vos documents Plastifie photos documents graphiques papiers d identit etc d une taille A4 max L appareil travaille avec 4 rouleaux chauffants a un temps d chauffement rapide et plastifie sans support e _2 lampes DEL indiquent les tats de fonctionnement e Mise hors service automatique en cas de surchauffe e Un syst me de chauffage de grande qualit emp che la formation de vagues et de bulles e Temps de mise en temp rature d env 5 minutes seulement e Temps de refroidissement temp rature ambiante d env 30 minu tes Epaisseur de la feuille de plastique d au moins 80 um et de 125 um maximum Syst me de plastification Technique Hot Roller 4 rouleaux de transport Largeur maximale de plastif
23. er in the insertion slot Residual adhe sive is removed and taken up by the paper when ejected Repeat the process several times Disconnect the power plug before starting to clean the unit with a damp cloth If necessary the housing can be cleaned using a cloth moistened with clean water with a little mild soap applied Never use any solvents or aggressive cleaning agents Troubleshooting Fault Corrective measures e Red LED POWER does not light e Check that the power plug has been up properly connected to the power socket e If the fault cannot be cleared con tact our hotline e Foil jam e Check the foil pockets being used are the correct size e Only use pouches of the size speci fied e Ensure that the pouch has been in serted correctly in the unit e To clear the fault follow the instruc tions in the Section Clearing Foil e Unit does not respond A BE da e Laminated foil is not completely e Laminate the same foil again to im transparent i prove the lamination result e If thicker foil is used 100 um 125 um please allow the device to heat up longer Conformity of the equipment to the EU directives is confirmed by the CE symbol 20 Disposal Notes This symbol the crossed out wheeled bin PICTURE means that the product should be brought to the return and or separate collection systems available to end users when the product has reached the end of its lifetime This symbol ap
24. esm byt nikdy zasunuta do vstupn t rbiny p stroje otev enou stranou jinak by do lo k jej mu zvr sn n P i zasouv n f lie respektujte pros m pokyny uveden na vstupn t rbin Laminov n prob hne automaticky Odstran n nakupen f lie Tento p stroj je vybaven funkc Jam Release jej pomoc lze rychle od stranit nakupenou f lii 1 Dojde li k zablokov n f lie vypn te p stroj a stiskn te dol a podr te p ep na ABS na prav stran p stroje 2 Dr te pevn laminovac p stroj a vyt hn te f lii sou asn s lamino van m materi lem ze vstupn t rbiny p stroje 3 Pot je nutno p stroj s nejv t pravd podobnost n kolikr t vy istit jak je pops no v odstavci dr ba a i t n 4 V p pad e soustavn doch z k nakupen f lie nebo nelze naku penou f lii z p stroje vyt hnout obra te se pros m na na i horkou lin ku viz odstavec Z ruka 61 dr ba a i t n Usazeniny a zbytky lepidla mohou negativn ovlivnit v sledek laminov n Proto je nutn posouvac v le ky pravideln po pou it vy istit Zasu te p elo en list ist ho pap ru do vstupn t rbiny Zbytky lepidla se zachyt na pap e a spolu s n m budou vytla eny ven Tento postup n kolikr t opakujte P ed i t n m p stroje vlhkou tkaninou v dy vyt hn te z str ku ze s t V p pad pot eby Ize zevn j ek
25. etzkabels vermeiden Netzkabel nie verdrillen Das Ger t bei besch digtem Netzkabel oder Netzstecker nicht in Betrieb nehmen Verwenden Sie das Ger t nicht in der Nahe von hei en Ober flachen oder in feuchter Umgebung und sch tzen Sie es vor di rekter Sonneneinstrahlung und starker Staubeinwirkung Vor dem Reinigen des Ger tes immer den Netzstecker ziehen Verwenden Sie keine L sungsmittel oder aggressive Reini gungsmittel Metallische Gegenstande k nnen nicht laminiert werden Kindern ist der Aufenthalt im Arbeitsbereich der betriebsbereiten Maschine nicht gestattet Bei Nichtbenutzung des Ger tes Netzstecker ziehen Das Ger t immer sofort ausschalten wenn ein strenger Geruch entsteht oder das Ger t nicht in Betrieb ist Netzstecker nicht mit feuchter Hand ber hren Stellen Sie sicher dass der Ein Aus Schalter in Stellung OFF ist bevor das Laminiergerat an das Stromnetz angeschlossen wird Nur daf r vorgesehene Folientaschen wie unter Punkt Leis tungsmerkmale angegeben in das Ger t einf hren Zu gro gew hlte Folientaschen k nnen Folienstaus verursachen Laminieren Sie keine hitzeempfindlichen Materialien mit diesem Ger t wie z B Thermopapier Beim Laminieren von feuchten Dokumenten erzielen Sie schlechte Laminierergebnisse Verwenden Sie keine Folientaschen die f r die Kaltlaminierung vorgesehen sind beim Hei laminieren Die Maschine die Fo lientasche und das Dokument werden dabei besc
26. ght and dusty con ditions Disconnect the power plug before starting to clean the unit Never use any solvents or aggressive cleaning agents Metallic objects cannot be laminated Children must not be allowed in the vicinity of the equipment when it is ready to operate Disconnect the power plug when the unit is not in use Always switch the unit off immediately if it emits a strong smell or it is not in operation Do not touch the power plug with moist hands Ensure that the On Off switch is in the OFF position before con necting the laminator to the mains power supply Only insert recommended foil pockets as specified in the Sec tion Features in the unit Using foil pockets which are too large could lead to the unit jamming Do not laminate heat sensitive materials such as thermal paper in the unit Lamination of moist documents produces poor results Do not use foil pockets intended for cold lamination for hot lamination This could damage the machine foil pockets and document Do not cut foil pockets to size The resulting cut edges could cause the foil pockets to jam Keep loose clothing ties jewellery long hair and other loose objects away from the infeed opening Risk of injury The socket and the mains connection of the device must be freely accessible for safety reasons so that the power supply can be dis connected in emergencies The device may only be used indoors in dry rooms 14 Recommenda
27. h v n pouh ch p ibli n 5 minut e Doba vychladnut na pokojovou teplotu p ibli n 30 minut e Tlou ka f lie od nejm n 80 um do maxim ln 125 um Syst m laminov n Hot Roller technika 4 posouvac v le ky Maxim ln ka laminovan ho 230 mm dokumentu Maxim ln tlou ka laminovan ho 0 5 mm dokumentu Rychlost laminov n 0 3 m min Nap jen 220 240 V 50 Hz P kon proudu 1 55 A V kon 345 W Rozm ry Dx xV 380 x 160 x 36 mm Hmotnost cca 1175 g 59 Laminov ni za tepla 1 Zapojte sitovy kabel do snadno dostupn standardni zasuvky A Pozor P esv d te se e daje o nap jen p stroje se shoduj s daji Va el s t 220 240 V 50 Hz 2 Zapn te p ep na Zap V p na prav horn stran p stroje I 3 Hnac motor posouvac ch v le k se spust erven kontrolka POWER sv t a za n f ze oh evu Po p ibli n 5 minut ch 80 um resp 6 minut ch 125 um je dosa eno spr vn laminovac teploty a zelen kontrolka READY sv t 4 Vlo te materi l ur en k laminov n do laminovac f lie tak aby z stal na v ech stran ch zachov n asi 3 a 5 mm odstup od okraje f lie A Pozor Pou vejte v hradn vhodn laminovac f lie pro laminov n za tepla 5 Zasunte f lii sou asn s laminovac m materi lem do vstupn t rbiny p stroje F lii zasu te uzav enou stranou nap ed Upozorn n
28. h digt Schneiden Sie keine Folientaschen zu Die entstehenden Schnittkanten k nnen Folienstaus verursachen Lose Teile von Bekleidung Krawatten Schmuck langes Haar oder andere lose Gegenst nde von der Einlass ffnung fernhal ten Verletzungsgefahr 18 Die Steckdose und der Netzanschluss des Gerates m ssen aus Sicherheitsgr nden frei zug nglich sein damit die Stromversorgung im Notfall schnell getrennt werden kann 19 Das Gerat darf nur in trockenen geschlossenen Raumen benutzt werden Empfehlung Wenn sehr weiche Materialien wie Servietten oder kleine Formate laminiert werden sollen dann empfehlen wir zur Vermeidung von m glichen Staus das Lamieniergut zusatzlich in ein gefaltetes Blatt Papier zu legen Dieses muss mit der Knickkante voran in das Laminiergerat eingef hrt werden Ausweise und Dokumente k nnen ihre G ltigkeit verlieren wenn sie laminiert werden weil die Dokumentenechtheit anschlieRend nicht mehr berpr fbar ist Falls Sie das Produkt einmal an eine andere Person weitergeben m chten legen Sie bitte diese Gebrauchsanweisung immer dazu Haftungsausschluss Wir Ubernehmen keine Garantie f r die Richtigkeit der Informationen die sich auf technische Eigenschaften sowie die hier vorliegende Dokumentation beziehen Das in dieser Dokumentation beschriebene Produkt und ggf dessen Zubeh r unterliegen einer st ndigen Verbesserung und Weiterent wicklung Aus diesem Grund behalten wir uns das Recht vor
29. hakelen en de schakelaar aan de rechterkant van het apparaat in de stand ABS zetten 2 Houd het lamineerapparaat vast en trek de folie samen met het te lamineren voorwerp uit de invoeropening van het lamineerapparaat 3 Vervolgens moet het apparaat waarschijnlijk enkele malen worden gereinigd zoals beschreven onder het kopje Verzorging en reiniging 4 Als de folie voortdurend klem komt te zitten of klem zittende folie niet meer uit het lamineerapparaat kan worden getrokken neem dan contact op met onze hotline 53 Verzorging en reiniging Aangekoekt materiaal en lijmresten op de transportrollen kunnen het lamineerresultaat verslechteren Daarom moeten de transportrollen regelmatig na gebruik worden schoongemaakt Hiervoor een gevouwen blad papier in de invoeropening steken Lijmresten worden door het eruit komend papier meegenomen Deze handeling enkele malen herhalen V r het vochtig afwissen van het apparaat altijd de stekker uit het stopcontact trekken Indien nodig kan de buitenkant worden afgewist met een doek die in milde zeep en schoon water is gedrenkt Gebruik geen oplosmiddelen of agressieve reinigingsmiddelen Storingen verhelpen Storing e Rode LED POWER brandt niet Apparaat reageert niet e Folie zit klem e Gelamineerde folie is niet volledig transparant CE Maatregel Controleer of de stekker van het netsnoer correct in het stopcontact is gestoken Neem contact op met onze hot
30. ica rullo a caldo 4 rulli di trasporto Larghezza di plastificazione mas 230 mm sima Spessore massimo di plastifica 0 5 mm zione Velocit di plastificazione 0 3 m min Tensione di alimentazione 220 240 Volt 50 Hz Assorbimento di corrente 1 55 A 345 W Dimensioni LxPxH 380 x 160 x 36 mm Peso ca 1175g 42 Plastificazione a caldo 1 Collegare il cavo di alimentazione ad una presa di corrente facilmente accessibile A Attenzione Verificare che il valore di tensione dell apparecchio corri sponda con quello della rete elettrica 220 240 V 50 Hz 2 Accendere l interruttore ON OFF sul lato superiore destro dell appa recchio I 3 Il motore di azionamento dei rulli di trasporto si avvia la lampada spia rossa POWER si accende ed inizia la fase di riscaldamento Dopo circa 5 minuti 80 um 6 minuti 125 um viene raggiunta la corretta temperatura d esercizio e si accende la lampada spia verde READY 4 Inserire il foglio da plastificare nella busta in pellicola in modo da avere su tutti i lati una distanza di circa 3 5 mm dal bordo A Attenzione Utilizzare esclusivamente pellicole per plastificazione a caldo 5 Inserire la pellicola insieme al foglio da plastificare nella fessura di in serimento della plastificatrice Inserire per primo il lato chiuso della busta in pellicola IS Avvertenza Per evitare la piegatura della pellicola di plastificazione non inserire mai per primo il lato aperto della busta
31. ication 230 mm Epaisseur maximale de 0 5 mm plastification Vitesse de plastification 0 3 m min Tension 220 240 Volt 50 Hz Consommation de courant 1 55 345 W Mesures L xl x H 380 x 160 x 36 mm Poids env 1175g 25 Plastification chaud 1 Branchez le c ble lectrique dans une prise de courant standard facile d acc s A Attention Contr lez si les donn es relatives a la tension de l appa reil correspondent bien a celles de votre r seau 220 240 V 50 Hz 2 Branchez l interrupteur Marche Arr t situ sur le c t sup rieur droit de l appareil I 3 Le moteur de commande des rouleaux de transport d marre le voyant lumineux rouge POWER s allume et la phase de mise en temp ra ture commence Au bout d env 5 minutes 75 um 6 minutes 125 um la temp rature de fonctionnement est obtenue et l indicateur lumineux verte READY s allume 4 introduisez le mat riau plastifier dans la poche de plastique de ma ni re ce que de tous les c t s il y ait une marge d env 3 5 mm par rapport au bord de la feuille de plastique Attention N utilisez que des feuilles plastifier chaud 5 introduisez la feuille de plastique avec le mat riau a plastifier dans la fente d introduction de la machine plastifier Introduire ici en premier le c t ferm de la feuille de plastique gt Remarque Afin d viter que la feuille de plastique forme un pli n in troduisez jamais le c
32. in pellicola nella fessura di inserimento della plastificatrice Nell inserimento della pellicola osservare le istruzioni riportate sulla fessura di inserimento La procedura di plastifica zione avviene automaticamente A Attenzione La pellicola in uscita dalla plastificatrice molto calda e molle Maneggiare quindi con cautela il prodotto plastificato Va Avvertenza Perla spianatura del prodotto plastificato possibile pressarlo con un libro o con un altro oggetto piano e pesante 43 Plastificazione a freddo 1 Collegare il cavo di alimentazione ad una presa di corrente facilmente accessibile A Attenzione Verificare che il valore di tensione dell apparecchio corri sponda con quello della rete elettrica 220 240 V 50 Hz 2 Accendere l interruttore ON OFF sul lato superiore destro dell appa recchio I 3 Il motore di azionamento dei rulli di trasporto si avvia la lampada spia rossa POWER e la lampada spia verde READY si accendono A Attenzione Avendo impiegato la plastificatrice poco prima per com piere la plastificazione a caldo si rendera necessario fare raffreddare la pla stificatrice fino L intervallo di raffreddamento dura fino a 30 minuti 4 Eliminare la pellicola protettiva dalla pellicola per plastificazione 5 Inserire il foglio da plastificare nella busta in pellicola in modo da avere su tutti i lati una distanza di circa 3 5 mm dal bordo 6 Inserire la pellicola insieme al foglio da plastificare ne
33. inf hrt werden Beim Einf hren der Folie bitte die Anweisungen am Ein f hrschlitz beachten Der Laminiervorgang erfolgt automatisch Folienstau beheben Dieses Laminierger t ist mit der Funktion Jam Release ausger stet um Folienstaus schnell wieder beheben zu k nnen 1 Beim Blockieren der Folie das Gerat ausschalten und den Schalter an der hinteren rechten Ger teseite ABS nach unten drucken und hal ten 2 Halten Sie das Laminierger t fest und ziehen Sie die Folie zusammen mit dem Laminiergut aus dem Einf hrschlitz des Laminierger tes 3 Danach muss das Gerat wahrscheinlich mehrmals wie unter Punkt Pflege und Reinigung beschrieben gereinigt werden 4 Falls sich Folienstaus standig wiederholen oder sich gestaute Folie nicht mehr aus dem Laminierger t ziehen lasst wenden Sie sich bitte an unsere Hotline siehe Garantie 11 Pflege und Reinigung Ablagerungen und Klebereste an den Transportwalzen k nnen das Lami nierergebnis beeinflussen Darum m ssen die Transportwalzen regelm ig nach der Benutzung gereinigt werden Hierzu ein gefaltetes Blatt Papier in den Einf hrschlitz einf hren Klebereste werden vom austretenden Papier mitgenommen Den Vorgang mehrmals wiederholen Vor dem feuchten Reinigen des Ger tes immer den Netzstecker ziehen Falls erforderlich kann das Geh use mit einem in milder Seife und klarem Wasser getr nkten Tuch gereinigt werden Verwenden Sie keine L sungs mittel oder agg
34. ione dei up 47 Garanzia sine ta ien nd 47 Nederlands DEB Belangrijke veiligheidsinstructieS eee nn n 48 le 49 Uitsluiting van aansprakelijkheid A 49 Voorgeschreven gebruik EE 49 Overzicht ee see he Seege eo es ie en ege AGREE an 50 Kennmerken is ii so ia abissi 51 HestlamiNeren voir ota 52 Koudlaminereni uil a 53 Klem zitttende folie losmaken sn 53 Verzorging en reiniging exa 54 Storingen verhelpen nnen versie een nme 54 Verwilderings lirio iaa 55 A LE 55 esky CD D le it bezpe nostn pokyny ss 56 Doporucenti vie essent dineren nn devon ie mate 57 Ae 57 Pou it p stroje odpov daj c jeho p vodn mu ur eni 57 O ae nine nina Inn 58 V konnostn ZNAKY E 59 Laminov n Za tepla nnn ennen si 60 Laminov n za studena ie 61 Odstran n nak pen fie eat 61 drzba a eases hoe lien 62 Odstraneni zavady un e iii 62 NS alle Ee EE 63 Zaruka sieeve Ni hia eel ele aten ta ab 63 Wichtige Sicherheitsanweisungen DE Um ein zuverl ssiges Arbeiten mit dem Laminierger t zu gew hrleisten beachten Sie bitte Folgendes 1 2 3 10 11 12 13 14 15 16 17 Lesen Sie diese Anweisungen bitte sorgf ltig durch und beach ten Sie sie bei der Handhabung Ihres Ger tes Bedienungsanleitung f r zuk nftige Benutzung aufbewahren Besch digung des Netzsteckers oder N
35. la funda de pel cula transparente y el documento sufririan 30 sufririan da os 16 No corte las fundas de pelicula transparente Los cantos de corte que se producen pueden originar atascos de pelicula transparente 17 Las partes sueltas de la ropa corbatas bisuteria pelo largo u otros objetos sueltos deben mantenerse alejados del orificio de entrada jPeligro de lesiones 18 Por motivos de seguridad la caja de enchufe y la conexi n a red del aparato deber n quedar accesibles para facilitar la desconexi n de la alimentaci n el ctrica en caso de emergencia 19 Utilice el aparato s lo en locales cerrados y secos Recomendaci n Cuando se trata de laminar materiales muy blandos como servilletas o formatos peque os entonces recomendamos a fin de evitar posibles atascos depositar el producto a laminar en una hoja de papel plegado ste se debe introducir con el borde de doblado hacia delante en el aparato laminador Si se laminan Documentos Nacionales de Identidad y otros documentos stos pueden perder su validez ya que a continuaci n no es posible comprobar la autenticidad de los documentos Si en alg n momento se entrega el producto a otra persona siempre se deber adjuntar las presentes instrucciones de uso Exclusi n de responsabilidad No asumimos garant a alguna para la integridad de las informaciones que se refieren a caracter sticas t cnicas as como a la presente documentaci n El producto des
36. line als de storing niet is verholpen Controleer het formaat van het gebruikte lamineerhoesje Gebruik alleen lamineerhoesjes van het voorgeschreven formaat Overtuig uzelf ervan dat het lamineerhoesje recht in het apparaat werd gestoken Volg de instructies onder het kopje Klem zitttende folie losmaken op om klem zittende folie uit het _apparaat te trekken Lamineer dezelfde folie nogmaals om het lamineerresultaat te verbeteren Als u dikkere folie 100 pm 125 pm gebruikt moet u het apparaat langer laten opwarmen 54 De overeenstemming met de EUrichtlijnen wordt bevestigd door de CE markering Verwijderings tip Dit symbool betekent dat het Product na zijn levensduur naar een verzamelpunt wordt terug gebracht door de laatst verkopende Dit symbool geldt alleen in de Staten van de E W R E W R Europa s gebied welke de EU staten de Noorwegen Ysland en Lichtenstein omringd Garantie Geachte klant Het verheugt ons dat u voor dit apparaat hebt gekozen Geef het apparaat in geval van een defect met de kassabon en de originele verpakking terug in de zaak waar u het gekocht heeft 55 D lezit bezpe nostni pokyn Respektujte pros m n sleduj c pokyny aby bylo zaru eno spolehliv zach zen s lamin torem 1 Pozorn si pros m pro t te tyto pokyny a dodr ujte je p i manipulaci s Va m p strojem 2 N vod k obsluze uschovejte k p padn mu pozd j m
37. lla fessura di in serimento della plastificatrice Inserire per primo il lato chiuso della busta in pellicola Avvertenza Per evitare la piegatura della pellicola di plastificazione non inserire mai per primo il lato aperto della busta in pellicola nella fessura di inserimento della plastificatrice Nell inserimento della pellicola osservare le istruzioni riportate sulla fessura di inserimento La procedura di plastificazione avviene automaticamente 44 Rimuovere l intasamento da pellicola Questa plastificatrice equipaggiata con la funzione Jam Release Rimo zione intasamento allo scopo di rimuovere rapidamente eventuali intasa menti causati dalle pellicole 1 In presenza di un intasamento causato dalla pellicola spegnere l ap parecchio e spostare l interruttore presente rispettivamente sul lato destro in posizione di ABS Rimozione intasamento 2 Tenere ferma la plastificatrice ed estrarre la pellicola assieme al do cumento da plastificare dalla fessura di introduzione della plastificatri ce 3 Fatto questo sar probabilmente necessario pulire l apparecchio pi volte seguendo quanto riportato al punto Cura e pulizia 4 Nel caso di frequenti intasamenti o non potendo estrarre la pellicola causa dell intasamento dalla plastificatrice si prega di rivolgersi alla nostra hotline Cura e pulizia Incrostazioni e residui di adesivo sui rulli di trasporto possono influire sul ri sultato di plastific
38. ltat de la plastification e En cas d utilisation d une pellicule plus paisse 100 um 125 um faire chauffer l appareil un peu plus Jongtempe Le signe CE confirme la conformit aux directives UE 28 Reseignement sur la vacuation Ce symbole un conteneur d chets barr d une croix signifie que le produit en fin de vie doit tre retourn une des syst mes de collecte mis la disposition des utilisateurs finaux Ce symbole s applique uniquement aux pays de EEE EEE Espace MM conomique europ en qui regroupe les Etats membres de l UE plus la Norv ge l Islande et le Liechtenstein Garantie Cher client Nous sommes tr s heureux que vous ayez choisi cet appareil En cas de d faut veuillez retourner l appareil dans son emballage d origine et accompagn du bon d achat au magasin o vous l avez achet 29 Instrucciones de seguridad importantes ES Tenga en cuenta los aspectos siguientes a fin de garantizar un trabajo fiable con el aparato laminador 1 2 10 11 12 13 14 15 Lea las presentes instrucciones detenidamente y tenga las mismas en cuenta a la hora de manejar el aparato Guardar el manual de instrucciones para cualquier utilizaci n posterior Evitar cualquier dafio de la clavija de red o del cable de red Jamas se debe torcer el cable de red En caso de cualquier da o del cable de red o de la clavija de red no se debe poner el aparato en servicio
39. minating 125 um On Off switch ON OFF Red LED Power Device switched on Green LED READY Device ready Insertion slot Oo 6060 Discharge slot 16 Features Protection and refinement of your documents Laminate photographs documents graphics identity cards etc up to A4 size The unit operates using 4 heating rollers has a quick warm up phase and laminates without a carrier e 2LED lamps indicate the operating states e Automatic switch off in the event of overheating e High quality heating system prevents smudging and blistering e Warm up phase only about 5 minutes e Cool down phase to room temperature approx 30 minutes e Foil thickness minimum 80 um and maximum 125 um Laminating system Hot roller technology 4 transport rollers Maximum laminating width 230 mm Maximum lamination thickness 0 5mm Laminating speed 0 3 m min Power supply 220 240 Volt 50 Hz Power consumption 1 55 A 345 W Dimensions LxWxH 380 x 160 x 36 mm Weight Approx 1175 g 17 Hot Laminating 1 Connect the power cable to an easily accessible standard electrical socket A Caution Check that the voltage specifications of the unit correspond to that of your power supply network 220 240 V 50 Hz 2 Switch on the On Off switch on the top right hand side of the unit 1 3 The drive motor for the transport rollers starts up the red indicator lamp POWER lights up and the warm up phase begins The correct operating temperature
40. n The equipment takes about 30 minutes to cool down 4 Remove the protective foil from the pouch 5 Insert the document to be laminated in the pouch so that there is a margin of approx 3 5 mm to the edge of the foil on all sides 6 Insert the foil containing the document in the laminator s insertion slot Insert the ready closed side of the foil first gt Note To prevent the laminating foil from creasing never insert the open end of the pouch in the insertion slot of the laminator first When insert ing the foil observe the instructions on the insertion slot The laminating process occurs automatically Clearing Foil Jams The laminator is provided with a Jam Release function in order to clear foil jams quickly 1 If the foil jams switch the equipment off and use the switch ABS on the right side of the unit 2 Hold the laminator firmly and pull the foil together with the document to be laminated out of the laminator s insertion slot 3 It will probably be necessary to then clean the unit several times as described in the Section Cleaning and Servicing 4 If foil jams occur repeatedly or jammed foil cannot be removed from the laminator please contact our hotline 19 Cleaning and Servicing Deposits and residual adhesive on the transport rollers can influence the re sults of the laminating process Therefore the transport rollers must be cleaned periodically after use To do this insert a folded piece of pap
41. ncher toujours imm diatement l appareil quand une forte odeur se fait sentir ou quand l appareil ne fonctionne pas Ne touchez pas la prise de secteur avec des mains humides Assurez vous que l interrupteur Marche Arr t est en position OFF avant de brancher la machine plastifier sur le r seau N introduire dans l appareil que des poches de plastique pr vues cet effet comme indiqu au point Caract ristiques Le choix de poches de plastique trop grandes peut entra ner un bourrage Ne plastifiez pas avec cet appareil des mat riaux sensibles la chaleur comme par ex le papier photosensible Vous obtiendrez de mauvais r sultats si vous plastifiez des do cuments humides N utilisez pas pour la plastification chaud des poches de plastique pr vues pour la plastification froid La machine la poche de plastique et le document en seraient endommag s Ne coupez pas les poches de plastique sur mesure Les ar tes de coupe form es peuvent provoquer un bourrage 22 17 Eloignez de l ouverture d introduction toute partie de v tement qui bouge cravates bijoux cheveux longs ou autres objets l air libre Risque de blessures 18 Pour des raisons de s curit la prise et le raccordement au r seau doivent tre facile ment accessibles afin de pouvoir inter rompre rapidement l alimentation lectrique en cas d urgence 19 N utilisez votre appareil que dans des pi ces ferm es et s ches Recommandation Si
42. nestraling en sterke stofbelasting V r het schoonmaken van het apparaat altijd de stekker uit het stopcontact trekken Gebruik geen oplosmiddelen of agressieve reinigingsmiddelen Metalen voorwerpen kunnen niet gelamineerd worden Kinderen moeten uit de buurt blijven van een ingeschakeld apparaat Als het apparaat niet wordt gebruikt dan moet de stekker uit het stopcontact worden getrokken Het apparaat altijd onmiddellijk uitschakelen als u een sterk prikkelende geur ruikt of als het apparaat niet wordt gebruikt Netstekker niet met vochtige handen vastpakken Overtuig uzelf ervan dat de Aan Uit schakelaar op Off staat voordat u het lamineerapparaat op het lichtnet aansluit Alleen geschikte lamineerhoesjes zie Kenmerken in het apparaat plaatsen Te groot gekozen lamineerhoesjes kunnen tot gevolg hebben dat de folie klem komt te zitten Lamineer met dit apparaat geen hittegevoelige materialen zoals thermisch papier Bij het lamineren van vochtige documenten bereikt u slechte lamineerresultaten Gebruik bij het heetlamineren geen lamineerhoesjes die bestemd zijn voor koudlamineren Het apparaat het lamineerhoesje en het document worden hierbij beschadigd Snij lamineerhoesjes niet op maat De snijkanten die hierbij ontstaan kunnen tot gevolg hebben dat de folie klem komt te zitten Loszittende delen van kleding stropdassen sieraden lang haar of andere losse voorwerpen uit de buurt van de invoeropening houden Gevaar voo
43. os 125 um se alcanza la temperaura de servicio correcta y la l mpara de indicaci n verde READY se ilumina 4 Introduzca el producto a laminar en el compartimento de laminaci n de tal modo que exista una distancia de aproximadamente 3 a 5 mm respecto al borde de la pel cula transparente en todos los lados A Atenci n Utilice exclusivamente pel culas transparentes de laminaci n en caliente 5 Introduzca la pel cula transparente junto al producto a laminar en la ranura de entrada del aparato laminador El lado cerrado de la pel cula transparente debe ser introducida en primer lugar IS Advertencia A fin de evitar el plegado de la pel culas transparentes de laminaci n jam s se debe introducir primero el lado abierto de la pel culas transparentes de laminaci n en la ranura de entrada del aparato laminador Durante la introducci n de la pel cula transparente se deben tener en cuenta las instrucciones que figuran en la ranura de entrada El proceso de laminaci n se realiza de forma autom tica A Atenci n La pel cula transparente saliente est muy caliente y blanda despu s de la laminaci n Por lo tanto se debe manejar el producto laminado con precaci n IS Advertencia Para aplanar el producto laminado se puede prensar el mismo con un contabilizar o con otro objeto pesado y plano 34 Laminaci n en frio 1 Conecte el cable de corriente a una caja de enchufe estandar facilmente accesible A Atenci n Comp
44. plies only to the countries within ME the EEA EEA European Economic Area which comprises the EU Member States plus Norway Iceland and Liechtenstein Warranty In the case of a defect please return the device together with the receipt and original packing material to the point of sale 21 Consignes importantes de s curit FR Afin de garantir un travail fiable avec la machine plastifier veuillez tenir compte des points suivants 1 2 3 10 11 12 13 14 15 16 Veuillez lire attentivement ces instructions et tenez en compte lors du maniement de votre machine Conservez le mode d emploi pour une utilisation future Evitez tout endommagement de la prise de secteur ou du c ble de r seau Ne jamais torsader le c ble de r seau Ne mettez jamais la machine en service si le c ble de r seau ou la prise de secteur sont endommag s N utilisez jamais la machine dans les environs de surfaces tr s chaudes ou dans un environnement humide et ne la soumettez pas un ensoleillement direct et une poussi re importante Retirez toujours la prise de secteur avant de nettoyer l appareil N utilisez jamais de solvants ou de produits d entretien agressifs Des objets m talliques ne peuvent pas tre plastifi s Il est interdit aux enfants de s journer dans la zone de travail quand la machine est pr te fonctionner Retirez la fiche de secteur quand vous ne vous servez pas de la machine D bra
45. port au bord de la feuille de plastique 6 Introduisez la feuille de plastique avec le mat riau a plastifier dans la fente d introduction de la machine a plastifier Introduire ici en premier le c t ferm de la feuille de plastique Va Remarque Afin d viter que la feuille de plastique forme un pli n in troduisez jamais le c t ouvert de la feuille de plastique dans la fente d in troduction de la machine Tenez compte des instructions donn es au niveau de la fente d introduction quand vous introduisez la feuille de plastique L op ration de plastification se fait automatiquement Elimination de bourrage Cette machine plastifier est quip e de la fonction ABS d blocage de bourrage permettant d liminer rapidement un bourrage 1 En cas de blocage de la feuille de plastique d brancher l appareil et mettre l interrupteur situ sur le c t droite en position Jam Release 2 Maintenez fermement la machine plastifier et tirez la feuille de plas tique avec le mat riau plastifier hors de la fente d introduction de la machine plastifier 3 Ensuite l appareil doit vraisemblablement tre nettoy plusieurs fois comme d crit au point Entretien et nettoyage 4 Si les bourrages par les feuilles de plastique se r p tent continuelle ment ou si la feuille bloqu e ne peut plus tre retir e de la machine a plastifier veuillez vous adresser a notre hotline 27 Entretien et nettoyage Des d p ts
46. r Information Ihr Inhalt ist nicht Vertragsgegenstand Alle angegebenen Daten sind lediglich Nominalwerte Die beschriebenen Ausstattungen und Optionen k nnen je nach den l nderspezifischen Anforderungen unterschiedlich sein Wir behalten uns inhaltliche und technische Anderungen vor 66
47. r persoonlijk letsel 48 18 Stopcontact en netstekker van het apparaat moeten om redenen van veiligheid vrij toegankelijk zijn opdat u de stroomvoorziening in geval van nood snel kunt onderbreken 19 Het apparaat mag alleen in gesloten droge ruimten worden gebruikt Advies Als zeer zachte materialen zoals servetten of kleine formaten moeten worden gelamineerd dan adviseren wij om het materiaal in een gevouwen vel papier te leggen Zo voorkomt u vastlopers Dit vel moet met de vouw naar voren in het lamineerapparaat worden ingevoerd Legitimatiebewijzen en documenten kunnen ongeldig worden als ze worden gelamineerd omdat de echtheid van het document vervolgens niet meer te controleren is Mocht u het product ooit aan een andere persoon willen doorgeven voeg dan deze gebruiksaanwijzing altijd bij Uitsluiting van aansprakelijkheid Wij aanvaarden geen aansprakelijkheid voor de juistheid van deze gebruiksaanwijzing of de informatie die betrekking heeft op technische eigenschappen van het product Het in deze documentatie beschreven product en de bijoehorende accessoires worden voortdurend verder ontwikkeld en verbeterd Daarom behouden wij ons het recht voor om componenten accessoires technische specificaties en deze gebruiksaanwijzing zonder voorafgaande aankondiging op elk gewenst moment te wijzigen Voorgeschreven gebruik Met dit lamineerapparaat kunnen heetlamineerfolies en koudlamineerfolies worden bewerkt Er kunnen foto
48. r un atasco de peliula transparente Este aparato laminador est equipado con la funci n ABS para poder eliminar r pidamente cualquier atasco de pel cula transparente 1 En caso de bloqueo de la pel cula transparente se debe desconectar el aparato y posicionar el interruptor en la parte derecha del aparato a la posici n Jam Release 2 Sujete el aparato laminador y pase la pel cula transparente con presi n junto al producto a laminar por la ranura de entrada del aparato laminador 3 A continuaci n es muy probable que haya que limpiar el aparato repetidamente seg n se describe en el punto Cuidado y limpieza 4 Si los atascos de pel cula transparente se repiten continuamente o si no es posible sacar la pel cula transparente atascada del aparato laminador rogamos se ponga en contacto con nuestra l nea de asistencia telef nica Cuidado y limpieza Las acumulaciones y restos de pegamento en los rodillos de transporte pueden repercutir sobre el resultado de laminaci n Por este motivo se deben limpiar los rodillos de transporte peri dicamente despu s de la utilizaci n del aparato A tal fin se debe introducir una hoja plegada de papel en la ranura de entrada El papel saliente arrastra los restos de pegamento Este proceso se debe repetir varias veces Antes de la limpieza en h medo del aparato siempre se deba sacar la clavija de red Si fuera necesario se puede limpiar la carcasa con un pa o empapado en jab n su
49. ressive Reinigungsmittel Fehlerbehebung Fehler L sungen O e Rote LED POWER leuchtet nicht e Pr fen Sie ob das Stromkabel Ger t reagiert nicht korrekt in die Standardsteckdose eingesteckt wurde e Falls der Fehler nicht behoben wurde wenden Sie sich an unsere e Hotline e Folienstau i e Pr fen Sie die Gr e der verwen deten Folientasche e Benutzen Sie nur Folientaschen in der angegebenen Gr f e e Stellen Sie sicher dass die Folien tasche gerade in das Ger t einge f hrt wurde i e Um den Stau zu beheben folgen Sie den Anweisungen unter Punkt Folienstau beheben e laminierte Folie ist nicht vollst ndig e Laminieren Sie dieselbe Folie er durchsichtig neut um das Laminierergebnis zu verbessern e Beim Verwenden dickerer Folie 100 um 125 um bitte das Ger t Die Konformit t mit den EU Richtlinien wird durch das CE Zeichen best tigt 12 Entsorgungshinweis Dieses Symbol die durchgestrichene Abfalltonne bedeutet dass dieses Produkt nach der Lebenszeit zu einem fur den Endanwender verf gbaren R cknahme oder getrenntem Sammelsystem zuruckgebracht werden muss Dieses Symbol gilt nur in den Staaten der EWR EWR Europ ischer Wirtschaftsraum welcher die EU Mit gliedstaaten plus den Staaten Norwegen Island und Liechtenstein umfasst Garantie Bitte unbedingt aufbewahren Lieber Kunde wir freuen uns dass Sie sich fur das Olympia
50. ruebe si la indicaci n de tensi n del m quina coincide con la de su red de corriente 220 240 V 50 Hz 2 Conecte el interruptor de conectado desconectado en la parte superior derecha del aparato I El motor de accionamiento para los rodillos de transporte arranca la l mpara de indicaci n roja POWER y la l mpara de indicaci n verde READY se iluminan Atenci n Si ha utilizado el aparato laminador recientemente para la laminaci n en caliente debe dejar que se enfr e El tiempo de enfriamiento dura hasta 30 minutos 4 5 Retire la pel cula de protecci n de la funda de pel cula transparente Introduzca el producto a laminar en el compartimento de laminaci n de tal modo que exista una distancia de aproximadamente 3 a 5 mm respecto al borde de la pel cula transparente en todos los lados Introduzca la pel cula transparente junto al producto a laminar en la ranura de entrada del aparato laminador El lado cerrado de la pel cula transparente debe ser introducida en primer lugar Va Advertencia A fin de evitar el plegado de la peliculas transparentes de laminaci n jam s se debe introducir primero el lado abierto de la pel culas transparentes de laminaci n en la ranura de entrada del aparato laminador Durante la introducci n de la pel cula transparente se deben tener en cuenta las instrucciones que figuran en la ranura de entrada El proceso de laminaci n se realiza de forma autom tica 35 Elimina
51. t Roller Technik 4 Transportwalzen Maximale Laminierbreite 230 mm Maximale Laminierdicke 0 5 mm Laminiergeschwindigkeit 0 3 m min Spannungsversorgung 220 240 Volt 50 Hz Stromaufnahme 1 55 A Leistungsaufnahme 345 W Abmessungen LxBxH 380 x 160 x 36 mm Gewicht ca 1175 g Hei laminieren 1 Schlie en Sie das Stromkabel an eine gut zug ngliche Standard steckdose an A Achtung Pr fen Sie ob die Spannungsangabe des Ger tes mit der Ihres Stromnetzes bereinstimmt 220 240 V 50 Hz 2 Schalten Sie den Ein Aus Schalter an der rechten Ger teoberseite ein l 3 Der Antriebsmotor f r die Transportrollen l uft an die rote Anzeige leuchte POWER leuchtet und die Aufw rmphase beginnt Nach etwa 5 Minuten 80 um bzw 6 Minuten 125 um ist die korrekte Betriebs temperatur erreicht und die gr ne Anzeigeleuchte READY leuchtet 4 Legen Sie das Laminiergut in die Folientasche so ein dass allseitig etwa 3 bis 5 mm Abstand vom Folienrand vorhanden ist A Achtung Verwenden Sie ausschlie lich geeignete Hei laminierfolien 5 F hren Sie die Folie zusammen mit dem Laminiergut in den Einf hr schlitz des Laminierger tes ein Die geschlossene Seite der Folie ist hierbei zuerst einzuf hren gt Hinweis Um ein Falten der Laminierfolie zu vermeiden darf nie die offene Seite der Laminierfolie zuerst in den Einf hrschlitz des Laminierger tes einf hrt werden Beim Einf hren der Folie bitte die Anweisungen am Ein
52. teek de netstekker in een goed bereikbaar stopcontact Let op Controleer of de voedingsspanning die op het apparaat vermeld staat overeenkomt met die van het elektriciteitsnet 220 240 V 50 Hz 2 Schakel de Aan Uit schakelaar aan de rechterbovenkant van het apparaat in I 3 De aandrijfmotor voor de transportrollen begint te draaien het rode signaallampje POWER licht op en de opwarmingsfase begint Na ongeveer 5 minuten 80 um 6 minuten 125 um is de juiste bedrijfstemperatuur bereikt en licht het groene signaallampje READY op 4 Leg het te lamineren voorwerp zodanig in het lamineerhoesje dat aan alle kanten 3 5 mm afstand tot de folierand overblijft A Let op Gebruik uitsluitend heetlamineerfolies 5 Steek de folie samen met het te lamineren voorwerp in de invoeropening van het lamineerapparaat De gesloten kant van de folie moet het eerst in het apparaat worden ingevoerd gt Opmerking Om vouwen in de lamineerfolie te voorkomen mag nooit de open kant van de lamineerfolie als eerste in de invoeropening van het lamineerapparaat worden gestoken Bij het invoeren van de folie beslist de instructies op de invoeropening opvolgen Het lamineerproces verloopt automatisch Let op De eruit komende folie is na het lamineren zeer heet en zacht Daarom voorzichtig omgaan met het gelamineerde voorwerp Va Opmerking Om het gelamineerde voorwerp plat te maken kan het onder een boek of ander zwaar voorwerp worden gelegd
53. tificazione a caldo e a freddo Possono essere plastificate fotografie cartine documenti lettere ecc con uno spessore complessivo di 0 5 mm Qualsiasi altro impiego da ritenersi non conforme alle disposizioni Non sono ammesse modifiche o variazioni arbitrarie 40 Vista generale 0 Rimozione intasamento da pellicola Jam Release Interruttore per plastificazione a freddo caldo Interruttore a sinistra plastificazione a freddo Interruttore al centro plastificazione a caldo 80 um Interruttore a destra plastificazione a caldo 125 um Interruttore di accensione spegnimento ON OFF LED rosso Power apparecchio inserito LED verde READY apparecchio pronto all esercizio Apertura di introduzione Oo 6060 Apertura di uscita 41 Caratteristiche di prestazione Protezione e valorizzazione per i vostri documenti Plastificazione di fotografie documenti grafiche tessere ecc fino ad alla grandezza DIN A4 L apparecchio dispone di 4 rulli a caldo il tempo di ri scaldamento breve e la plastificazione viene eseguita senza supporto 2 spie LED indicano lo stato di funzionamento spegnimento automatico in caso di surriscaldamento ottimo sistema di riscaldamento contro la formazione di strie e bolle tempo di riscaldamento di soli ca 5 minuti tempo di raffreddamento fino a temperatura ambiente ca 30 minuti spessore di pellicola da minimo 80 um a massimo 125 um Sistema di plastificazione Tecn
54. tion If very soft materials such as serviettes or small formats are to be lami nated then we recommend placing these within a folded piece of paper to avoid possible jamming The piece of paper has to be placed in the lamina tion device with the folded edge first Identification papers and documents can lose their validity if they are lami nated because they can then no longer be checked In case you wish to let another person use this product please include these instructions Exemption From Liability We cannot guarantee that the information on the technical properties and that contained in this document is correct The product and where applica ble its accessories described in this document are subject to constant im provement and further development For this reason we reserve the right to modify components accessories technical specifications and related docu mentation of the product at any time without notification Intended Use This laminator has been conceived for use processing hot and cold laminat ing foil It is possible to laminate pictures maps documents paper etc up to a total thickness of 0 5 mm Any other use is considered unintended use Unauthorised modifications or reconstructions are not permitted 15 Overview 0 Clearing Foil Jams Jam Release Hot Cold Laminating switch Left position Cold laminating Center position Hot laminating 80 um Right position Hot la
55. tions Vue d ensemble 0 0 5 cee essen ie eee eo 24 Caract ristiques de performance 25 Plastification chaud 26 Plastification froid EE 27 Elimination de bourrage arianna 27 Entretien et nettoyage nn rvs see aa riali Elimination d erreurs sise Reseignement sur la vacuation Garantie asie Espa ol Es Instrucciones de seguridad importantes 30 RECOMENDACI N risccavionamt needs acid 31 Exclusi n de responsabilidad nnnr rn rn 31 Uso previStO its gain 31 Vista EE Caracter sticas prestacionales Laminaci n en caliente Laminaci n en Trio Eliminar un atasco de peliula transparente 36 V Be lee Wun EE 36 Eliminaci n de fallos nnn vererven tive vier ieee aie eee ee 37 Indicaci n sobre la eliminaci n de residuos 2 2 ee eee 38 Garantie EE 38 Italiano M CR Istruzioni importanti di sicurezza anneer enneerenveneerenneneen eneen 39 COMINO iii A i 40 Esclusione di responsabilit cc ennen rn nennen nennen 40 Impiego conforme alle disposizioni nc cnnnnnns 40 NICK EC 41 Caratteristiche di prestazone cnn nono eeen enneerenne rn rre 42 Plastificazione a CAldO ii 43 Plastificazione a freddo rniran iaia lavata 44 Rimuovere l intasamento da pellicola eneen eneen 45 DECH EE 45 Soluzione di problem iet narici eh 46 Indicazione sopra l eliminaz
56. to In caso di inutilizzo dell apparecchio estrarre la spina di alimen tazione Procedere allo spegnimento immediato dell apparecchio non appena si sviluppa un forte odore o in caso di non impiego Non toccare la spina di alimentazione con le mani bagnate Assicurarsi che l interruttore ON OFF sia in posizione di OFF pri ma di collegare la plastificatrice alla rete elettrica Inserire nell apparecchio solo pellicole per plastificazione da come descritto al punto Caratteristiche di prestazione La scel ta di pellicole per plastificazione troppo grandi pu causare un intasamento della pellicola Evitare di compiere con l apparecchio la plastificazione di mate riali sensibili al calore come per es carta termica per fax In caso di plastificazione di documenti umidi i risultati saranno insoddisfacenti Evitare durante la plastificazione a caldo l uso di pellicole per plastificazione previste invece per la plastificazione a freddo In caso contrario l apparecchio la pellicola di plastificazione ed il documento saranno danneggiati Non tagliare le pellicole di plastificazione nel tentativo di adat tarne le dimensioni Gli spigoli da taglio risultanti possono infatti causare un intasamento della pellicola 39 17 Tenere lontano dall apertura di inserimento le parti libere del l abbigliamento cravatte gioielli capelli lunghi o altri oggetti li beri Pericolo di lesioni 18 Per motivi di sicurezza la presa e il c
57. tores tiene un rapido Tiempo de calentamiento y lamina sin materias portantes e Las 2 l mparas de LED muestran los estados de servicio Desconexi n autom tica en caso de sobrecalentamiento e El sistema de calentamiento de alta calidad impide la formaci n de marcas y burbujas e Tiempo de calentamiento reducido de s lo aproximadamente 5 minutos e El tiempo de enfriamiento hasta alcanzar temperatura ambiente es de aproximadamente 30 minutos e Espesor de pel cula transparente de al menos 80 um y de 125 um como m ximo Sistema de laminaci n T cnica Hot Roller 4 rodillos de transporte M xima anchura de laminaci n 230 mm M ximo espesor de laminaci n 0 5 mm Velocidad de laminaci n 0 3 m min Alimentaci n de tensi n 220 240 Voltios 50 Hz Consumo de corriente 1 55 A 345 W Dimensiones longitud x anchura x 380 x 160 x 36 mm altura Peso Aproximadamente 1175 g 33 Laminaci n en caliente 1 Conecte el cable de corriente a una caja de enchufe est ndar f cilmente accesible A Atenci n Compruebe si la indicaci n de tensi n del maquina coincide con la de su red de corriente 220 240 V 50 Hz 2 Conecte el interruptor de conectado desconectado en la parte superior derecha del aparato I 3 El motor de accionamiento para los rodillos de transporte arranca la l mpara de indicaci n roja POWER se ilumina y la fase de calentamiento comienza Al cabo de aproximadamente 5 minutos 80 um 6 minut
58. u pou it 3 Chra te z str ku a s ov kabel p ed po kozen m S ov kabel nikdy nep ekrucujte Neuv d jte p stroj do provozu v p pad e je po kozen s ov kabel nebo z str ka 4 Nepou vejte p stroj v bl zkosti hork ch povrchov ch ploch ani ve vlhk m prost ed a chra te ho p ed p m m slune n m z en m a prachem 5 P ed i t n m p stroje vyt hn te v dy z str ku ze s t Nepou vejte dn rozpou t dla ani agresivn ist c prost edky 6 Nelze laminovat kovov p edm ty 7 D tem je zak z no zdr ovat se v pracovn ch prostor ch provozuschopn ho p stroje 8 Neu v te li p stroj vyt hn te z str ku ze s t 9 P stroj ihned vypn te pokud z n j vych z pronikav z pach nebo nen li p stroj v provozu 10 Nedot kejte se z str ky vlhk ma rukama 11 P ed zapojen m lamin toru do s t se ujist te e je p ep na Zap Vyp v poloze OFF 12 Do p stroje zav d jte pouze f lie ur en k tomuto elu jak je uvedeno v odstavci V konnostn znaky V b rem p li velk ho form tu f lie m ete zp sobit nakupen f lie 13 Nelaminujte s t mto p strojem dn materi ly kter jsou citliv na teplo jako nap termopapir 14 Laminov n m vlhk ch dokument dos hnete jen patn ch v sledk 15 Nepou vejte p i laminov n za tepla f lie kter jsou ur en k laminov n za stu
59. uando llegue al final de su vida til Este s mbolo solo tiene validez en los pa ses de la EEA WN EEA incluye a los pa ses miembros de la UE y Noruega Islandia y Liechtenstein Garant a Estimado cliente nos alegramos de que Usted se haya decidido por este aparato En caso de un defecto devuelva el aparato junto con el justificante de compra y el embalaje original al lugar donde lo ha adquirido 38 Istruzioni importanti di sicurezza IT Per garantire un funzionamento affidabile della plastificatrice si prega di osservare quanto segue 1 2 3 10 11 12 13 14 15 16 Leggere attentamente queste istruzioni ed osservarle scrupolo samente nell utilizzo del vostro apparecchio Conservare le istruzioni per l uso per gli utilizzi futuri Evitare danneggiamenti della spina o del cavo di alimentazione Non attorcigliare il cavo di alimentazione In caso di spina o ca vo di alimentazione danneggiati non mettere in funzione l appa recchio Non utilizzare l apparecchio nelle vicinanze di superfici roventi o in ambiente umido e proteggerlo dall esposizione diretta dei raggi del sole e dall influenza di ambienti fortemente polverosi Staccare sempre la spina di alimentazione prima della pulizia dell apparecchio Non utilizzare solventi o detergenti aggressivi Non possibile la plastificazione di oggetti metallici Tenere lontano i bambini dal campo di lavoro dell apparecchio in condizioni di funzionamen
Download Pdf Manuals
Related Search
Related Contents
Payroll Self Service user guide Installationsanleitung Buderus GB145 Operating instructions - Compressors for Commercial Refrigeration VLAN Administration Guide For the Sun Ethernet Fabric Operating Asrock N68-S3 UCC motherboard (AED)の適切な管理等の実施について(再周知) [PDFファイル/1.07MB] Mode d'emploi Eye Level 50-KITWWCS Installation Guide Copyright © All rights reserved.
Failed to retrieve file