VXi BlueParrott B250-XT
Contents
1. 1 4 ADDITIONAL FEATURES TURN HEADSET INDICATOR LIGHTS OFF ON A quick press of both the volume up and volume down buttons at the same time will turn the headset indicator lights off or on A tone will be heard and the indicator lights will turn off repeat to turn the indicator lights on Headset must be in standby mode or on a call to use this feature The default state of the indicator lights upon power up 1s on AUTOMATIC BLUETOOTH CONNECTION When the headset is powered on it will automatically attempt to connect to the last device it was paired with If the headset was paired with multiple devices and the last connected device is not available turned off out of range etc the headset will attempt to connect to the second to the last device it was connected to etc It is also possible to reconnect to the device with a quick press of the headset s MFB A tone will be heard and the two devices should connect 17 SPECIFICATIONS Range Up to 66 feet Best range is achieved with line of sight positioning of headset and cell phone Certain conditions and obstructions such as wireless devices placing your phone on a metal surface such as your vehicle s hood walls etc can inhibit radio wave transmission and reduce range Talk Time 16 hours on a 12 hour charge Standby Time Up to 150 hours on a 12 hour charge Auto DC Charger Inline Fuse Replacement If neither of the headset charging indicators light when the2. for a long period of time you should repeat this 12 hour charge IMPORTANT Failure to charge less than 12 hours may result in shorter talk time AC Charger DC Charger 5 ON STANDBY OFF Turn Headset On Hold down the MFB for 2 3 seconds until you hear 2 rising tones The red light will flash once every second Standby Mode After the headset is turned on it will attempt to connect to the last device that it was paired with putting itself into standby mode The headset can also be put into standby mode with a quick press and release of the MFB The blue light will flash indicating an active Bluetooth link Turn Headset Off conserves battery power Hold down the MFB for 2 3 seconds until you hear 2 falling tones A red light will flash 4 times and the headset will turn off S MAKE A CALL END A CALL Ifyou have not paired the headset and phone together yet you must do so panel 6 1 Turn on your cell phone Be sure the Bluetooth option is enabled on your phone refer to your phone s user guide for instruction 2 Put headset on and properly position the microphone panel 7 To turn headset on press MFB for 2 3 seconds The headset will automatically attempt to connect with the last device it was paired or connected with Once connected the headset will enter standby mode 3 Dial the phone and make a call as usual 4 To end call quickly press the MFB on the headset and release You will he
3. TABLE OF CONTENTS Safety Instructions Glossary 2 Charge the Headset 3 Battery Power Indicators 4 Headset Controls 5 On Standby Off 6 Pair Headset with the Phone 7 Microphone Positioning 8 Make a Call End a Call 9 Answer a Call End a Call 10 Pairing with a Computer 1 Operation While Using the Charger Adapter 12 Last Number Redial 12 Reject a Call 13 Voice Dial 13 Transfer Audio 14 Turn Headset Indicator Lights Off On 14 Automatic Bluetooth Connection 15 Multiple Device Pairing 16 Reset Paired Devices List 17 Specifications 3 BATTERY POWER INDICATORS Indicator Lights After the initial 12 hour charge the indicator lights will indicate the level of battery power as follows Green light Fully charged Up to 16 hours talk time Green amp red lights together Approximately 60 seconds away from full charge Red light Less than a full charge Keep charger plugged into headset when not in use to res avoid battery drain It s not necessary for the charger to be plugged into a power source to take advantage of this For best performance keep charging headset when not in use 6 PAIR HEADSET WITH THE PHONE Keep headset amp phone no less than 3 inches and no more than 3 feet apart while pairing Keep other Bluetooth devices at least 50 ft away or turn them off Note The headset can be paired with up to 3 different devices 1 Turn headset off panel 5 2 Hold down
4. ar 2 falling tones the call will end and the headset will enter standby mode OPERATION WHILE USING THE CHARGER ADAPTER 11 The B250 XT headset will operate from battery power or from the AC or DC charger adapter Note Do not attach the charger mid call This causes the headset to turn off call will not be lost When the headset is operating from the battery all indicator lights and sounds will function as described in this guide When the headset is operating from the charger adapter the headset including the audio indicators will function as described in this user guide However the MFB lights will indicate the battery charge status see Panel 3 After the battery is fully charged the MFB charge light will turn and stay green as long as the charger adapter is connected to the headset While the headset is fully charged and the charge light is green the blue indicator light will also be on if the headset is powered on FUNCTIONS AND INDICATORS AT A GLANCE Function Button Duration of press Audio Indicator Visual Indicator Lights bliieparrott 8250 XT parrot USER GUIDE MFB Multifunction Button Power on MFB 2 3 sec Power off MFB 2 3 sec Enter pairing mode MFB 5 15 sec Two rising tones Blue light flashes Two falling tones All lights go off Two Four rising tones Red amp blue lights flash alternately Volume up Volume down Vol Up quick press Vol Dwn quick press Single tone None Sing
5. auto adapter is connected to the headset and power source check the charger s inline fuse Replace with 1A 250V Slow Blow glass fuse 3AG if necessary Fuses are available at most automotive stores To replace simply unscrew the tip of the auto adapter see photo right and remove the fuse be careful not to lose the spring that is inside Put new fuse in and screw the tip back on
6. block noisy surroundings it s possible to adapt to volume that is too high e Check with local and state laws regarding cell phone handset usage while operating a motor vehicle Replace only with same or equivalent battery Dispose of batteries according to local regulations Do not throw batteries in a fire as they could explode Do not immerse any part of this product in water e Plastic bags and small parts may cause choking if ingested Keep them away from small children and pets e Use only the power cords included with this product e Avoid temperatures exceeding 140 F will cause equipment failure GLOSSARY OF TERMS Paired Two Bluetooth devices agree to communicate with one another On Headset is on but there is no connection to the phone red light will flash Standby Mode Headset is on Bluetooth link is active the user is not on a call blue light will flash Talk Mode Headset is being used with the cell phone while the cell phone is on an active call HEADSET CONTROLS Multifunction Button MFB amp Indicator Lights Volume Up amp Microphone Mute Volume Down Volume Increase Quickly press and release the Volume Up Mute button Repeat until desired volume is attained Volume Decrease Quickly press and release the Volume Down button Repeat until desired volume is attained Microphone Mute Un Mute Hold down the Volume Up Mute button for 2 seconds until you hear a beep A mute reminde
7. evices except for the one being paired must either be powered off or at least 50 ft away during the pairing process Once all devices are paired connection to the last paired device can be made by turning the headset off and then on again or with a quick press of the MFB The headset will connect to the devices in opposite order of pairing For instance if device A B and C were paired in that order connection will be established to C first If C is not available turned off out of range the headset will connect to B etc VXI WARRANTY 1 VXI warrants that your B250 XT headset system will be free from defects in material and workmanship for one year from the date of purchase If during the first year from the date of purchase your B250 XT headset system fails to work due to a defect in material or workmanship VXI will repair or replace the product at its election free of charge Without proof of purchase the warranty period begins on the date of manufacture Consumable components for example cushions battery and fuse are not included in this one year warranty You may register your warranty online at www vxicorp com or by calling customer service at 1 800 742 8588 2 The foregoing limited warranty does not cover equipment failure attributable to accident improper operation misuse abuse or any cause other than defects in the materials or workmanship of VXI s products 3 VXI s obligations under this warranty are limi
8. le tone None Mute on Mute off Vol Up 2 sec Vol Up 2 sec Single tone None Singe tone None Short reminder beep every 10 seconds while mute is on Voice dial start Voice dial end Last number redial Answer a call MFB 1 quick press MFB 1 quick press Vol Dwn 1 sec MFB quick press Single tone None Single tone None Single tone None Two rising tones Blue light flashing every 1 sec End a call MFB quick press Reject a call MFB 2 sec Sends call to Voice Mail if available Transfer audio Vol Dwn 1 2 sec 1 2 ADDITIONAL FUNCTIONS Note Your cell phone must support the following functions consult the phone owner s manual LAST NUMBER REDIAL To re dial the last number that was dialed from the cell phone press and hold the volume down button for approximately 1 second A beep will be heard and the phone will redial the last number REJECT A CALL To reject an incoming call press and hold the MFB for 2 seconds You will hear 2 falling tones and the incoming call will be transferred to your voice mail if available More functions on panel 13 1 5 MULTIPLE DEVICE PAIRING The B250 XT can pair with up to three devices at the same time however only one device may be connected to the headset at a time To pair the headset with a Bluetooth cell phone or other Bluetooth device such as a Bluetooth enabled computer follow the instructions in panel 6 and 10 of this manual Remember that all d
9. ll phone while on a call press and hold the volume down button for 1 2 seconds A tone will be heard and audio will transfer to the phone repeat to transfer audio back to the headset When audio is transferred to the phone all headset activity lights and sounds will stop until audio is transferred back to the headset 16 RESET PAIRED DEVICES LIST To reset the headset s internal paired devices list press and hold both the volume up and the volume down buttons for 5 6 seconds A double beep with be heard and the list will be reset This procedure may be necessary if the headset will not pair or connect to a device NOTE Pairing information for devices previously paired with the headset will be lost Headset will need to be paired to the device after reset has occurred FCC NOTICE TO USERS This part complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Users are not permitted to make changes or modify the device in any way Changes or modifications not approved by VXI Corporation will void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable p
10. r beep will be heard every 10 seconds Repeat to un mute MICROPHONE POSITIONING Position microphone near corner of your mouth Correct positioning ensures that the noise cancellation technology works properly Slight adjustment of the microphone may help to achieve optimum performance 10 Keep headset amp computer no less than 3 inches and no more than 3 feet apart while pairing Keep all other Bluetooth devices at least 50 ft away or turn them off PAIRING WITH A COMPUTER 1 Turn headset off panel 5 2 Open the computer s Bluetooth connection manager 3 Put headset into pairing mode Panel 6 Step 2 4 Instruct Bluetooth connection manager application to discover Bluetooth device Enter passcode 0000 when prompted 5 Wait 5 15 seconds while the devices discover each other The headset s blue light will stop flashing and the red light will continue to flash After pairing is complete the Bluetooth computer will ring the headset Press and release the MFB once to establish a Bluetooth link to the computer Press and release the MFB again to disconnect from the computer Once paired connection can be made by pressing the volume down button for 1 2 seconds Tones will be heard and a connection should be established 2 CHARGE THE HEADSET Select charger cord and plug it into the charger port on the headset Charge for 12 full hours before first use Note If you do not use your headset
11. rotection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antennae Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CANADA IC NOTICE TO USER Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation of the device This device complies with RSS 210 of Industry Canada This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Printed in China Compatible with Bluetooth phones amp Bluetooth enabled computers Windows or Macintosh
12. ted to repair or replacement at our option of any defective part returned to VXI at the customer s expense Returned products require a Return Authorization that may be obtained by calling 1 800 742 8588 Products returned to VXI for repair under this warranty will be return shipped to the customer at VXI s expense 4 THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not permit the exclusion of implied warranties and the foregoing exclusions may not apply to you 5 In no event shall VXI be responsible for any other damages whatsoever including direct indirect special incidental consequential or other damages for breach of this or any other warranty express or implied VXI Corporation One Front Street Rollinsford NH 03869 USA 1 800 742 8588 603 742 2888 www blueparrott com PN202710B 2009 VXI Corporation Two falling tones Two falling tones None Blue light flashing every 4 sec Long tone None 1 3 ADDITIONAL FUNCTIONS VOICE DIAL To use the voice dial feature of the cell phone quickly press the MFB on the headset a tone will be heard and the phone s voice dialer should open clearly speak the command Repeat quick press of the MFB to end voice dial The headset must be in standby mode to use this feature TRANSFER AUDIO To transfer audio from the headset to the ce
13. the headset s MFB until the red and blue lights flash and you hear 2 rising tones followed by 4 more tones Important Wait for all tones and for both lights to flash This may take up to 15 sec Release the MFB 3 Follow the manufacturer s instructions for putting your cellular phone into Bluetooth discovery mode 4 Wait 5 15 sec while the devices discover each other When the phone discovers the headset select Pair and enter a passcode of 0000 when instructed When pairing is complete the headset s blue light will stop flashing and the phone will prompt you to connect to the headset Enter Yes on the phone to connect to the headset When connected the blue light will flash indicating that the headset is in standby mode ready to receive a call Q ANSWER A CALL END A CALL In order to answer a call the headset must be in standby mode panel 5 1 Put headset on Position the microphone panel 7 2 When your cell phone rings you will hear ring tones in the headset Answer the call by quickly pressing the headset s MFB and release 3 To end the call quickly press the MFB on the headset and release You will hear 2 falling tones the call will end and the headset will enter standby mode 1 SAFETY INSTRUCTIONS GLOSSARY e Avoid hearing damage Set volume at lowest comfortable level If you experience ringing in your ears or people sound muffled stop using the headset Avoid turning up volume to
Download Pdf Manuals
Related Search