Da-Lite Designer Electrol, 175 x 234 cm
Contents
1. The Da Lite Difference Instruction Book for DESIGNER ELECTROL T DA LITE es 3100 North Detroit Street Post Office Box 137 Warsaw Indiana 46581 0137 Phone 574 267 8101 800 622 3737 Fax 574 267 7804 Toll Free Fax 877 325 4832 www da lite com e mail info da lite com IMPORTANT SAFETY INSTRUCTIONS When using your video equipment basic safety precautions should always be followed including the following Read and understand all instructions before using Position the cord so that It will not be tripped over pulled or contact hot surfaces If an extension cord is necessary a cord with a current rat ing at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may over heat To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons SAVE THESE INSTRUCTIONS PRE INSTALLATION Before proceeding with the installation of the screen please read the installation and operations instructions thoroughly Ay caution Do not cut wrapping paper or tape with knife or any sharp tool Pull orange string 1 Carefully unpack the screen2. and remove the outer wrapping 2 Always handle screen in upright position 3 Remove the front cover of the screen from the back of the screen Lift front cover up approximately 1 2 and pull away from back of screen See Figure 1 4 There are two methods of mounting the screen suspended from ceiling and wall mounted See Figure 2 NOTE Allow 1 2 above screen when mounted for front cover of screen installation and removal 5 Picture surface is centered in case Case extends 5 1 2 beyond surface on either end Do not attach anything to screen slat on the bottom of the screen HANGER BRACKET ty I QUE HANGER PIN FRONT 5 COVER PICTURE SURFACE SLAT FIGURE 1 WALL MOUNTING CEILI V BAR MOUNTED TO THE WALL WALL ALLOW A MINIM 1 1 4 FROM CE alles NG UM OF LING Y BAR MOUNTED TO THE BACK OF THE CASE AT THE FACTORY FIGURE 2 TURE RFACE CEILING MOUNTING WMA PLACE D RINGS OVER HOOKS WELL SECURED IN CEILING DESIGNER ELECTROL INSTALLATION 1 4 Hang screen from wall or ceiling FOR WALL MOUNTING HARDWARE PROVIDED 2 V Bars one is factory mounted to the back of the case one will be mounted to the wall 6 Toggle Bolts 4 6 Lead Shields 10 14 x 1 6 Phillips Flat Head Wood Screws 10 x 2 TOOLS REQUIRED Electric Drill Masonry Bit e if mou
3. fuse Tripped circuit breaker No power to operating switch or junction Power at junction box e Thermal overload tripped Broken wire in the up or down position Defective motor limit switch or capacitor Temporary binding Capacitor burned out Lost roller wrap Down limit switch out of adjustment Lost roller wrap Up limit switch out of adjustment Squeaking rubber end plug rubbing on motor Grinding due to foreign object in screen rubbing on roller or fabric Gear noise a Defective brake a Pin end slipped out of nylon bear 1 2 3 ing RESTORING LOST ROLLER WRAP Push strap over back of roller Tape end of strap to pocket Feed fabric as you pull strap to draw fabric over top Remove tape and strap 5 b c a a Verify 115 125V or 220 240V If insufficient voltage rewire incom ing electric line Replace fuse Reset circuit breaker Check above Tighten all loose wire connections Correct any improper connections Down Position Check for power across black and white leads Up Position Check for power across red and white leads Let motor cool down for 15 minutes Try again Check for continuity Cut off old splice and reconnect Replace motor assembly NOTE Motor is a sealed assembly With power off turn roller by hand to free binding Replace motor assembly See instructio
4. imit switches that are preset at the factory If it s necessary to adjust for more or less drop follow the steps below The case cover must be removed to access the motor limit switches Remove the front cover of the screen from the back of the screen Lift front cover up approximately 1 2 and pull away from back of screen See Figure 1 SETTING THE DOWN LIMIT POSITION TO REDUCE SCREEN DROP Turn the white limit switch screw clockwise to decrease the amount of screen drop Run the screen down to test the stop position If the screen drops too far raise the screen about one foot and adjust the limit switch again Repeat until the desired position is set TO INCREASE SCREEN DROP Turn the white limit switch screw counterclockwise to increase the amount of screen drop Run the screen down to test the stop position If the screen does not drop enough raise the screen about one foot and adjust the limit switch again Repeat until the desired position is set Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller TROUBLESHOOTING CAVS E SOLUTION SYMPTOM 1 Screen will not operate Motor does not hum Motor hums 2 Incorrect stopping position in downward direction 3 Incorrect stopping position in upward direction 4 Noise NOTE Screen will operate with a low pitched hum 5 Coasting 6 Roller displaced from mounting bracket Incorrect line voltage Blown
5. n accordance with the requirements of the Local Building Codes the Canadian Electrical Code CED CAN CSA C22 1 and the National Electric Code NEC NFPA 70 gt A a EEE lO 4 5 1 2 PICTURE SURFACE O A FABRIC WIDTH 11 B FABRIC WIDTH DESIGNER ELECTROL INSTALLATION 120V WIRING DIAGRAM EXTERNAL WIRING TO BE COMPLETED BY INSTALLER TO JUNCTION BOX MOUNTED IN SCREEN CASE IN WHICH INTERNAL WIRING TERMINATES IN WHITE BLACK AND RED LEADS SIDE VIEW DOWN WHITE LIMIT OF SWITCH SWITCH KNOB AND BOX UP RED LIMIT SWITCH KNOB OPERATING SWITCH SWITCH BOX AND PLATE FURNISHED IN MULTIPLE CONTROL INSTALLATIONS ROCKER WITH SCREEN SPDT WITH THIS SWITCH IS REPLACED BY THE LOW CENTER OFF VOLTAGE CONTROL OPERATED FROM AC COMMON PUSH BUTTON STATIONS SEE DIAGRAM AC Nos 46967 AND 74425 AVAILABLE UPON BLACK WITH YELLOW 120 VOLTS REQUEST 50 60 HZ 2 5 MAX AMP THIS SWITCH CANNOT BE USED WITH LVC NOTE A single switch cannot be used to operate more than FIGURE 3 one screen Contact the factory for further information 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram included in wall switch box included with screen SCREEN ADJUSTMENT FOR 120V AND 220 240V SCREENS Screen travel is stopped automatically in the down and up positions by the l
6. ns below See installation instructions See instructions below Adjust up limit switch Turn clockwise to expose more fabric See installation instructions Adjust roller to center of case Remove foreign object Replace motor assembly Replace motor assembly Remove pin end mounting Re align motor in tube Re attach DIN eno LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Da Lite Screen Company Inc warrants its products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepa
7. nting in solid masonry or concrete Screw Driver 2 Flat Tip if using toggle bolts or 2 Phillips if mounting in solid masonry or concrete Determine the height of the top of the case from the floor This will be the height of the wall mounted V bar Hold the loose V bar to the wall at the height determined above MAKE SURE IT IS LEVEL and mark the loca tion for the screw holes To mount the V bar on solid concrete or masonry wall drill 6 holes and insert the lead shields Fasten the V bar to the wall using the 10 x 2 wood screws If you are mounting to a hollow wall drill holes and insert the toggle bolts Then fasten the V bar to the wall with the toggle bolts Now set the case in place on the wall with the V bar of the case nestled into the V bar on the wall FOR CEILING MOUNTING Position and properly anchor screw hooks into ceiling beam or other solid surface Then proceed to use the two D rings that are factory mounted to the top of the case to hang the case securely Remove black tape from slat Install electrical hook up that applies to your unit Make sure to review your electrical installation checklist and wiring diagrams included for either 120 volt switch 220 240 volt switch or low voltage control See Figure 3 Test installation by running screen up and down a few times Be prepared to stop screen Standard Duty Cycle 1 MIN ON 3 MIN OFF NOTE Must be installed i
8. y all transportation expenses THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA LITE S WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership
Download Pdf Manuals
Related Search