Spatz Miniscale
Contents
1. Operation Manua 1 Intoduction This professional video scalerisdesigned to convert Composite and S Video to high definition DVI resolutions It handles video input from TV systems of NTSC PAL TV standards with many great featuresto enhance video performance 2 Features 1 OP N I 8 9 Motion adaptive 3D Y C separation comb filter forcomposite video input 3D frame Based motion adaptive YNR CNR noise reduction forY C video input Advanced 3D motion adaptive deintenace Automatic 2 2 3 2 film mode detection Sup ports 50Hz to 60Hz fra me rate conversion Video quality improvement DCTI Digital chroma transient improvement DLT Digital luminance transient improvement Black level extension Average picture level APL Automatic contrast limiter ACL function supported OSD menu for picture quality adjustment Built in 8 bit DAC for RGB or YPbPr output 10 Front Panel and IR remote control 11 Automatic NTSC PAL video format detection and switching 3 This package includes 1 Video Scaler Unit 2 DC adaptor 3 User Manual 4 Remote Control 4 Operation Controls and Functions Front Panel POWER INPUT O p 1 Power button and LED indicator Pressthe button once to poweron the unit Pressagain to power off when the unit is powered on one of the input LEDs will illuminate depending on your last selection of input source before power off The factory default setting forthe inp2. RGB 1920 x 1200
3. desired parameter then press M ENU ENTER to enter into sub menu of your selected para meter Picture Adjust When Picture Adjust is selected a sub menu as below comes up Default Range 16 Bright 1 31 V Contrast 16 1 31 Color 16 1 31 Tint 16 1 31 Sharp 05 1 19 Default OK Exit USE to move the tick V to your desired adjust item Press the Menu Enter to confirm your selection At this point the selected para meter will tum red and you can use to increase ordecrease the value of the parameter When adjustment is complete Press Menu to leave the parameter Move the tick V to Exit then press menu enterto exit Output Setup When Output Set up isselected a submenu asbelow appears Output Setup V Timing XGA Exit Press the MENU ENTER button to enter into output timing select mode Press to toggle through a variety of output resolutions as below Once your desired resolution is selected pressthe menu enter to enterthe resolution Resolution Vertical rate NGA 800x600 60Hz XGA 1024x768 60Hz WXGA 1280x768 60Hz UXGA 1600x1200 60Hz WUXGA 1920x1200 720x480 720x576 1280x720 follow input source 1920x1080i follow input source 1920x1080p Note 1 All output resolutions except 576p have 60Hz vertical rate The 576p resolution has 50Hz vertical rate 7 DVI I Pin Configuration DVI Integrated DVI 1 Supports both analog and digital connections to the display This 29 pin c
4. V displa y unit using a DVI to DVI cable Analog output If you are to use CM 1391 s analog output to connect to the analog input of your PC or HDTV you need to use a DVI to VGA adaptorto pull out analog signal from the DVI I connector The DVI to VGA adaptor is then connect to the VGA input of your display monitor through a VGA cable if output is PC resolution or connect to the YPbPr input of your HDTV through a VGA to YPbPr 3 RCA adaptor cable if output is HDTV resolution Note DVI to VGA adaptor is not included in the standard package and has to order separately 2 5 Output Format a The format of digital DVI output is digital RGB for all resolutions lo reee HDIV RGBHWV vga RGB 640x480 1920x1080p follow input source syGA RGB 800x600 1920x1080i follow input source XGA RGB 1024x768 1280X720 follow input source WXGA RGB 1280x768 720X576 sxga RGB 1280x1024 720X480 UXGA RGB 1600 x 1200 WUXGA RGB 1920 x 1200 b The format for analog PC outputis RGB and for analog HD output is YPbPr RGB 1920x1080p follow input source RGB 1920x1080i follow input source RGB 1280X720 follow input source WXGA RGB 720X576 SXGA RGB 720X480 UXGA RGB 1600 x 1200 WUXGA RGB 1920 x 1200 6 OSD Operation After power on the unit press the menu button to bring up the main menu page asbelow Main Menu V Picture adj Output Setup Exit Use button to move V to your
5. onnector can cany single or dual link all digital video data signals on 24 pins and uses 5 pins to cany analog video data signals and ground Combined Analog and Digital Connector Pin Assignments Pn Sorar asmen _Trnsonst siommen Tem gral Asignment a Tmospet2 o Tmosossr u TMDSDateo ajne fm E me O rs pocco FO eV Power E mosco e Analog verieaisme 16 HotPlug Detect 2a TmDschee Analog Red Analog Horzontalsyne 05 Analog Ground OOOO o 8 Remote Control 1 Display Pressthe button to display input source and output resolution on the screen 2 Power Power ON OFF button 3 VGA 1080p Press to select your desired output resolution 4 Picture Press the button to enter picture adjust submenu Use button to move cursor V up down to your desired parameter press Picture again to confim 5 Pressto move up down the cursor V to your desired parameteror press to increase decrease the setting value 6 Reset Pressto reset all setting back to factory default value 7 Exit To exit OSD 8 Video Pressthe button to select composite video input 9 SVideo Pressthe button to select SVideo input 9 Specifications Weight ao 576p WUXGA 1080i 1080p sikscreen Color 1920x1080p follow input source RGB end 1920x1080i follow input source RGB 1024768 1280X720 follow input source RGB 1280768 720X576 RGB 1280X1024 720X480 RGB 1600 x 1200 WUXGA
6. ut is CV composite video The green LED illuminates when composite video is selected The Yellow LED illuminates when S Video is selected 2 Input select button Pressthe button to select your desired input source between composite video and S Video 3 IR Sensor Infra d remote control sensor 4 Menu Enter This button serves two purposes a Pressthe button to bring up OSD main control menu as shown in the OSD Operation b To actasa enter key to enter sub menu of you selected item or adjust value of the selected item 5 6 H button Press the button to move up ordown the tick V to your desired parameter Oraftera parameter is selected by pressing MENU ENTER button press the button to alterthe value of your selected parameter Re ar Pa nel DVI I OUTPUT mm INPUT mm DC 5V 1 DC power jack 5V 2A DC power input 2 Composite Video Use a Composite video cable to connect the composite video output of the source equipment to this composite video CV input of the scaler 3 S Video Use a SVideo cable to connect the S Video output of the source video equipment to this S Video input on the back of the video scaler S Video provides improved performance over composite video and is recommended over composite 4 DVI output The CM 1391 can output a variety of PC and HDTV progressive resolutions in both digital and analog format through DVI I connector Digital output Connect CM 1391 s digital DVI output to the DVI input of your T
Download Pdf Manuals
Related Search