DT Research DT390i
Contents
1. recommend using the Stylus provided to keep the screen clean Avoid prolonged exposure of the display panel to any strong heat source Wherever possible the DT390i should face away from direct light to reduce glare If the AC DC power adapter is used to recharge or power the device do NOT use any AC DC adapter other than the one provided with the device or acquired from the manufacturer or its partners In the unlikely event that smoke abnormal noise or strange odor is present immediately power off the DT390i and disconnect all power sources Report the problem to your device provider immediately e Never attempt to disassemble the DT390i as this will void the warranty e The DT390i internal battery is designed for wide temperature usage Please do not use it for other tablet models The wide temperature design is not applicable for external battery Basic Features The DT390i wireless tablet integrates a bright and responsive touch display 1 USB port and embedded networking elements such as wireless LAN or optional 3G The primary device is complemented by a suite of accessories including battery expansion docking cradles and wall vehicle mount cradles for a comprehensive user experience A DT390i typically integrates an 802 11a b g n wireless LAN WLAN adapter that may connect to other wireless devices or access points If your DT390i does not come with such a network adapter please consult your device provider to establish2. the desired network connectivity OPERATION Internal Battery Warning The Internal battery pack should only be replaced by an authorized DT Research service representative Please contact your product and or service provider for internal battery replacement service Powering ON and OFF To activate the DT390i push and quickly release the Power Button The display will come on ina few seconds To put the DT390i in Standby mode push and quickly release the Power Button To turn the DT390i off for extended storage power off the device safely using any software function that shuts down computer provided in the software operating system NOTE The battery packs shipped with your device may be low in power please use the AC DC adapter with the DT390i when setting up the device for the first time to fully charge the internal battery pack You may charge the external battery pack with it attached to the DT390i or with the optional external battery charger kit NOTE When the battery pack s is are charging the blue colored Battery LED should blink slowly If plugging in the AC DC adapter does not trigger this blinking activity and the LED stays dark the battery pack s may have been drained substantially Try unplugging replugging the AC DC adapter to the DT390i a few times to activate the charging process NOTE To conserve power use push and quick release the Power Button to put the device in Standby mode whil
3. DT3901 SPECIFICATIONS System Processor Intel Atom Z530 1 6GHz Memory RAM 2GB DDR2 533MHZ Microsoft Windows Embedded Standard 7 Windows 7 Operating Systems Professional Windows XP Embedded Windows XP Pro for Embedded Systems or Linux Sse a with resistive touch sunlight Indicator h power battery status LED and 1 WLAN actve tD Reads ISO 7816 T 0 T 1 EMV 2000 certified 1 8 3 5V Full Slot Smart Card Reader Smart card Power AC DC Adapter Input 100 240V AC Output 19V DC 2 36A Optional External 7 4V 3760mAh 7 2V 3900mAh Mechanical Enclosure ABS PCDI Weight 2st Environmental A IP64 IP64 rating may not be applicable for units with module Water and Dust Resistance E a Pay Vibration and Shock Resistance MIL STD 810G Regulatory FCC Class B CE C Tick ROHS compliant Operation 20 C 50 C The DT390i must be charged until the power LED indicator blinks blue then the 390i can be used in low temperatures Storage 20 C 60 C Humidity 0 90 non condensing Specifications subject to change without notice Temperature DT Research Inc 2000 Concourse Drive San Jose CA 95131 http www dtresearch com DT Res arch rch Copyright 2012 DT Research Inc All Rights Reserved DT Research is a registered trademark of DT Research Inc BOG030712DT390iENG DT Res arch h Mobile POS Tablet DT390 BASIC OPERATION GUIDE ENGLISH I
4. NTRODUCTION Thank you for acquiring the latest addition to DT Research s line of mobile tablets the DT390i Featuring an IP64 rated slim yet robust enclosure the two pound DT390i with 8 9 TFT display is powered by the Intel Atom processor offering optimal combinations of performance and power savings An external battery expansion option provides approximately 3 4 hours of additional battery operation for up to eight hours of mobile usage The DT390i is available with Windows Embedded Standard 7 Windows XP Embedded Windows XP Pro for Embedded Systems Windows 7 Pro or Linux operating systems Each software operating system features web browser client server computing software media player accessories and applications support PACKAGE CONTENTS e DT390i with Internal Battery Pack Stylus and Bumpers e AC DC Power Adapter with Power Cord e Basic Operation Guide e Handstrap Major options depending on configuration e Desktop Charging Cradle with DC in Power Jack and Ethernet USB Ports e X handstrap e External External Battery Pack and Battery Charger Kit e Vehicle Wall Mount Cradle If your DT390i contains MSR half slot smart card reader RFID reader camera 3G or scanner module please refer to the POS module operation guide for detailed operation The DT390i with Windows XP Operating System Microphone Wireless LED Battery Power LED z Q Calibration Ba
5. d USB ports Always seat the DT390i securely onto the cradle The cradle must be powered by the AC DC adapter for the Ethernet and USB ports to function The battery packs on the DT390i may be recharged by connecting the AC DC adapter directly to the DC in port on the DT390i or through the DC in port on the Cradle while the DT390i is docked For More Support Users can download the Software Utility and Modules Operation Guides from the DT Research website If the DT390i comes with a 3G module please contact your product and or service provider for the SIM Card Slot Location and Insertion Guide
6. e not in use Pushing briefly on the same button will wake up the system within seconds NOTE Avoid using the Power Button hold 4 seconds feature to turn off the device this form of hardware shutdown is intended to be a means of recovery from device lockups and not as normal operation Start Up If the power up from Standby or otherwise is successful the appropriate interface will be displayed after a launch sequence of several seconds The wireless LAN connection may take 10 15 seconds to be established Configuring the DT390i The device may be configured using the utilities and methods dictated by the software operating system The DT390i should be configurable for various properties such as user profiles network features and several system elements Calibration The touch display for the DT390i is calibrated before shipping In the event that the calibration has been modified or is unsatisfactory the respective calibration routines e g PenMount PM for Windows XP to calibrate the touch interface may be used Such applications are typically executed through touch input via Stylus or through mouse click via a USB mouse Wireless Networking Wireless LAN The DT390i is often delivered with an embedded user inaccessible 802 11a b g n WLAN adapter equipped with a hidden custom antenna e Through the support of typical WLAN adapters the DT390i should be able to detect all 802 11 access points in the vicinity for y
7. l battery pack that clips hot pluggable onto the back of the device the maximum period of continuous operation will be approximately 6 8 hours The period between battery recharges can be significantly lengthened by putting the device into Standby mode through the Power Button see Buttons Function Table whenever the device is not in use Depending on the operating software the DT390i may also be configured to enter various power saving modes via the Power Button or through timed entry Full Slot Smart Card Reader The DT390i comes with a full slot smart card reader e Remove the rubber and insert a card Picture 1 e Use the stylus to pull the metal pull and then remove the card Picture 2 Picture 1 Picture 2 USING THE DT390i Memory amp Storage Configuration The DT390i is available with 2GB memory configuration Storage options currently range from 2GB to 32GB flash memory Peripherals Support Through its USB port the DT390i supports a wide range of USB based peripherals These peripherals are applicable for software installation applications storage data storage docking or software recovery and update The DT390i is complemented by an optional Desktop Cradle or Wall Vehicle Mount Cradle for support pass through charging and connection to a range of USB peripherals including keyboard and mouse The Cradles offer the following interfaces a DC in port for the AC DC adapter an Ethernet port a VGA output an
8. ou to select the access point of your choice for connection The SSID and WEP WPA WPA2 if enabled parameters on the DT390i and the access points have to match The SSID is case sensitive and it is recommended that you enable WEP WPA WPA2 encryption or advanced alternatives for secure access When WEP WPA WPA2 is enabled you may need to consult your network admin istrator or your networking equipment literature to properly configure associated settings such as Authentication mode etc Refer to the access point operating manuals for setting up the 802 11 access points Button Management Where supported by software many of the hard buttons on the DT390i are programmable to perform a function of the user s choice The exception is the Power Button and the SAS Button To activate the button re assignment application invoke the Button Manager application e g in Windows XP Embedded i Brightness Control Where supported by device firmware and software a hard button may be engaged to manipulate the display brightness Press the System Utility Menu button Button 7 on the front of the DT390i The System screen will display a Brightness control section with up and down arrows that can be activated with the stylus Battery and Power Management The DT390i is equipped with an internal 3760mAh Li lon battery pack that is capable of supporting approximately 3 4 hours of continuous operation With the internal battery and an externa
9. ttery and Power Meter Wireless Network Settings Button Management Input Output Ports Q Headphone Jack USBPort O DC Power Input Full Slot Smart Card Reader Button Functions with Windows XP Operating System BUTTON ACTION Programmable Programmable launch soft on screen keyboard default Launch SAS Secure Attention Sequence Generate Ctrl Alt Del keys to invoke the security windows defined under Windows XP Programmable Calibrate touch screen before log on the operating system Change display orientation portrait landscape default Programmable system utility menu default Programmable O As scanner trigger when equipped with the scanner module Power on Push release typically enters Standby mode or Push release exits Standby mode or restarts device software dependent Push and hold over 4 seconds invokes hardware shutdown Power Battery LED Status e Blue indicates the battery is 25 to 100 charged e Blinking blue indicates the battery is charging e Orange indicates that the battery is between 11 to 25 e Blinking orange indicates that the battery is below 10 e Blinking blue and orange alternately indicates the battery is being warmed up Do not unplug the AC DC adapter Precautions e Always exercise care when operating and handling the DT390i e Do NOT apply excessive pressure to the display screen e We
Download Pdf Manuals
Related Search