Bixolon SRP-770 label printer
Contents
1. sure that the power supply is not plugged into an electrical outlet And the power supply s rated voltage and your outlet s voltage do not match contact your dealer for assistance Then do not plug in the power cord Otherwise you may damage the power supply or the printer 1 Make sure that the printer s power switch is turned off and the power supply s power cord is unplugged from the electrical outlet 2 Check the label on the power supply to make sure that the voltage required by the power supply matches that of your electrical outlet 3 Plug in the power supply s cable as shown below Notice that the flat side of the plug faces down Universal Serial Bus Parallel Interface Serial Interface USB RS 232 default setting is 19200 baud no parity 8 data bits and 1 stop bit Note Defaultly you can use Serial and Parallel Interface If you want to use USB Interface please turn on the Dip S W2 4 5 Installing or Replacing the Paper Roll 6 Setting The Dip Switches 6 1 Setting the Dip Switches Open Cover Q Open Guides The Dip Switches are located on the bottom of the printer The Dip Switches are used to set the Printer to perform various functions Follow these steps when changing Dip Switches setting 1 Turn the printer power switch off 2 Remove the screw on the bottom of the printer and open the bracket 3 Flip the Dip Switches using tweezers or another narrow ended tool Switches are off when2. ELECTRO MECHANICS SRP 770 Thermal Label Printer Operator s Manual JE68 00131B http www samsungminiprinters com Safety Precautions In using the present appliance please keep the following safety regulations in order to prevent any hazard or material damage WARNING Violating following instructions can cause serious injury or death Do not plug several products in one multi outlet This can provoke over heating and a fire f the plug is wet or dirty dry or wipe it before usage Ifthe plug does not fit perfectly with the outlet do not plug in Be sure to use only standardized multi outlets PROHIBITE S Do not pull the cable to unplug This can damage the cable which is the origin of a fire or a breakdown of the printer PROHIBITE S Do not plug in or unplug wit wet You can be electrocuted PROHIBITE Do not bend the cable by force or leave it under any heavy object A damaged cable can cause a fire You must use only the supplied adapter It is dangerous to use other adapters ONLY SUPPLIED ADAPTER Keep the plastic bag out of children s reach If not a child may put the bag on his head PROHIBITE If you observe a strange smoke odor or noise from the printer unplug it before taking following measures Switch off the printer and unplug the set from the mains After the disappearance of the smoke call your dealer to repair it Keep the desiccant
3. oltage 5 45 C Operating 25 70 Storage Environmental conditions _ 30 80 RH Operating Humidity 10 90 RH Storage Except for paper 10 000 000 lines Mechanism Head 5x10 pulse 50km MCBFO Mechanism 20 000 000 lines Temperature 13
4. out of children s reach If not they may eat it PROHIBITE Use only approved accessories and do not try to disassemble repair or remodel it for yourself Call your dealer when you need these services DISASSEMBLING PROHIBITED Do not let water or other foreign objects in the printer If this happened switch off and unplug the printer before calling your dealer S t a PROHIBITE Violating following instructions can cause slight wound or damage the appliance Install the printer on the stable surface If the printer falls down it can be broken and you can hurt yourself Do not use the printer when it is out of order This can cause a fire or an electrocution Switch off and unplug the printer before calling your dealer TO UNPLUG PRINTER DEALER 1 Unpacking Your printer box should include these items If any items are damaged or missing please contact your dealer for assistance Printer SRP 770 Operator s Manual Label Paper Power Cord Power Supply 2 Samsung Label Printer Feed Button Status Indicator Cover Peel off Power Switch Cover Open Close Printer Head Paper Holder Paper Guide Paper gap Sensor Paper Adjuster Peel off Sensor Interface Connectors RS 232C IEEE1284 USB 3 Connecting the Power Supply 4 Connecting the Interface Cable CAUTIONS When connecting or disconnecting the power supply from the printer make
5. t the thermal head becomes very hot during normal operation creating the danger of burn injury Be sure to wait for about 10 minutes after turning printer power off before beginning the cleaning 1 Open the printer cover 2 Clean the thermal element the area which is marked a thin black line of the thermal head with a cotton swab moistened with a alcohol solvent ethanol methanol or IPA 3 After confirming that the alcohol solvent has been dried up completely close the cover open Note 1 Never touch the thermal element with your hand then the thermal element can be damaged 2 Don t scratch the printer head 10 8 The Peel off Printers can Peel off a single label You must remove the label before the printer prints the next label 1 Open the peel off cover and turn on peeler switch 2 Remove the one a paper and 3 Adjust the paper guides and close the cover insert the paper through slot remove 11 9 Using Fan Fold Paper Insert paper through both the rear slot and guides Adjust holders and guides to the width of the paper Open the Dust Cover and Insert paper Adjust holders papers and paper Fixed Paper Fixed 12 thes Adjust Guides Dust Cover Specification Printing method Thermal line printing Printingwidth 54 101mm x Note Printing speed may be slower depending on the data transmission speed and the combination of control commands Supply v
6. up and on when down in the Figure below 4 The new setting takes effect when you turn on the printer Install Roll Note Always change Dip Switch settings only when the printer is turned off 6 2 Functions of Dip Switches 4 Close Guides to the Width of the paper 5 Close Cover 6 2 1 Dip S W 1 Off On On Off On On 115 200 bps On On ste neal 4 3 Density Selection Of On_ On Of B On On 20 High 5 6 Developer 7 Position Move to Cutting Position Selection On Move to top of next page 2 3 4 Interface Selection 5x8 Developer Default off Mode 7 The Self Test and Autosense Gapsensor Adjustment The self test checks whether the printer has any problems And perform this procedure when loading a new roll You cannot perform this procedure if using the printer s label peel off option If the printer does not function properly contact your dealer The self test checks the following Make sure that paper roll has been installed properly 2 Turn on the power while holding 2sec down the FEED button The self test begins 3 The self test prints the current printer status which provides the control ROM version and the DIP switch setting x Cleaning Head Paper dust on the heating elements may lower the printer quality In this case clean the print head as follows Cautions 1 Turn Off the printer power before cleaning 2 Note tha
Download Pdf Manuals
Related Search