Pyle PDWM2600
Contents
1. gt LE E PDWM 2600 DUAL UHF WIRELESS MICROPHONE SYSTEM OPERATION MANUAL www pyleaudio com PDWM 2600 DUAL UHF WIRELESS MICROPHONE SYSTEM OPERATION MANUAL Thanks for your support and trust to us while choosing our wireless microphone series with excellent quality To ensure it functions well Please read this manual carefully before operation PDWM 2600 EC PO 2600 komach Avoid exposure of the system to rain or moisture No user serviceable parts inside the system Refer all servicing to a qua lified technician only Handle the microphone carefully dropping or other shocks may cause failure Avoid using the system where it may be subjected to heat such as in direct sunlight near radiators or other heat sources Should any liquid be spilt on the system stop using it immediately It may be possible to dry the system but you should have it checked by a quali fied technician before using it again Take care with the mains power adapter and lead If damaged in any way do not use the system and refer to a qualified technician for repair Only use the system with the supplied components do not attempt to use with any other mains power supply adapter Ifthe microphone is not going to be used for a time remove the battery to prevent leakage In the event of electrolyte leakage inside the battery compartment carefully remove using a da2. king that the red LED comes on for a Note that switching the microphone on and off can cause interference that second and then goes off When the microphone is ON the SIGNAL light yi be RK if the microphone volume level of the amplifier system is still set high will illuminate on the receiver unit toes HANDHELD MICROPHONE DIAGRAM pz z oe lt lt SS gt MICROPHONE BATTERY UNSCREW BATTERY COVER TO INSERT BATTERY BATTERY CONDITION POWER SWITCH BATTERY COVER Unscrew the battery cover at the end of the microphone Install the provided 9 volt battery taking care to fit it with the correct polarity connected Check the battery by switching the microphone ON The red LED will come on for one second and then go OFF this indicates correct operation If the red LED stays ON or is dim this indicates the battery is low and should be changed If the red LED does not come on at all it indicates the battery is dead please change it right now E INSTALLATION To connect the wireless microphone to your amplifier system Refer to the installation diagram below Using the supplied jack to jack lead connect from the AF OUT jack socket to the MICROPHONE INPUT socket on your amplifier Plug the mains power adapter into a suitable mains socket and plug the lead connector into the DC 12V input socket With voltage selector switch for selecting a suitable AMPLIFIER one accordi
3. mp cloth Take care not to get battery electrolyte in contact with your skin however if it does wash your hands under a running tap If electrolyte comes into contact with your eyes seek medical advice immediately Only replace the battery with the same or an equivalent type Please dispose of old batteries in an environmentally friendly manner in accordance with the relevant legislation Do not use any solvents to clean any part of the wireless microphone system AE ae RECEIVER UNIT operation i kos PYLE PDWHM 2600 k B E q J DUAL UHF WIRELESS MICROPHONE SYSTEM J H POWER Mik aie onus Om O POWER SIGNAL B 8 O O MIN ANT MIX ANT E O saueien REY E J e o o BALANCED AF OUT BALANCED AERIAL B OUTPUT JACK DC POWER IN AERIAL A OPERATION Switch on the wireless microphone receiver unit by pressing the POWER The wireless microphone is now ready for use adjust the volume and switch and the POWER light will illuminate to show the receiver unit is tone levels of your amplifier system as well as the receiver amp the handheld working Raise the aerials to the maximum height The positioning of the Mic as required When the wireless microphone is not being used turn aerials is not critical for performance ideally it should be fully extended _ OFF the microphone Switch ON the microphone chec
4. ng to different countries EQ MIC INPUT OOO SBUELCH AF OUT EN Dc 14 BALANCED VOLTAGE 7 SELECTOR SWITCH RADIO MIC A RECEIVER UNIT gt MAINS POWER ADAPTER z SPEAKERS TROUBLE SHOOTING Please read and check the following points before asking for service The wireless microphone fails to work check the microphone battery by switching the microphone ON thered LED battery condition indicator should come on fora second and then go off If the red LED stays on or is dim replace the battery Ifthe red LED fails tocome on check the battery polarity or change battery Check the POWER indicator on the receiver unitis ON if not check the mains power adapter is firmly plugged into a working mains socket Check the amplifier system is ON and the microphone controls set correctly Check the wireless microphone jack lead is firmly connected into the output socket on the rear panel ofthe receiver unit andinto the MIC input socket on your amplifier The working range is limited Check the microphone battery condition see above Check the aerials are fully extended Adjust the position of aerials to achieve the best reception Feed back howl roung is heard Check thatthe microphone is not being used too close to or in front of the loundspeakers Check the settings ofthe microphone controls o
5. nthe amplifier adjust volume and tone to get the best sound without any trace of feedback SPECIFICATIONS A OVERALL SYSTEM 1 Oscillation mode 2 Carrier Frequency Range 3 Stability 4 Max Deviation 5 Dynamic Range 6 S N Ratio 7 T H D 8 Squelch 9 Frequency Response 10 Operation range REVELVER Sensitivity Image Rejection Stability Audio output Power supply Dimensions Weights ZAMADN y C WIRELESS MICROPHONE 1 Mike capsule 2 Antenna 3 RF Output 4 Spurious 5 Battery Quartz controlled UHF690 960MHz 0 005 56KHz with level limiting gt 110dB gt 100dB lt 0 5 Pilotone amp noiselock dual squelch circuit 60 Hz 18KHz 200ft 6dBpv at S N gt 70dB gt 60dB gt 80dB 12db 6000hm unbalanced and balanced 12V 15VDC 0 5A power supply 10 8 L x 5 9 W x 14 2 H 1 0kg approx Dynamic microphone Built in housing lt 10mW lt 40dBC one 9V battery ee A
Download Pdf Manuals
Related Search