Pyle PLVWR1982
Contents
1. WARNING DO NOT WATCH TV WHILE VEHICLE IN MOTION Cnr PYLE view INSTRUCTION MANUAL PLVWR1982 19 inch Roof Mount TFT LCD Monitor Thank you for purchasing of this roof mounting 19 inch TFT LCD monitor Before operating the unit please read this manual thoroughly and keep it for future reference PRECAUTIONS The Unit is for DC 12V Mobile vehicles Only Do not operate other than described in this guide Doing so may damage it and may void your warranty SAFETY FIRST IFOR REAR SEAT VIEW USE ONLY Do not install on dashboard or anywhere else that would permit monitor to be viewed by the driver Monitor must never be used in any manner that will distract driver or interfere with the driver s safe operation of the motor vehicle Be careful not to run down the car battery while using the Unit with the car stopped Do not disassemble or modify the Unit Doing so may damage it and voids your warranty Keep drinks and drops from umbrellas away from the Unit Water may damage the internal circuitry Do not let the Unit become hot If temperature in the car is high or the Unit has been exposed to direct sunlight and is hot lower the temperature before using it In extremely cold temperatures the movement of the picture may be slow and the picture may be dark but this is not a malfunction The Unit will work normally once the temperature increases Small Black and shiny dots inside the liquid crystal panel ar2. oo o Qo o oo Ta ea Be ape bracket to the headliner Use short screws so as not to damage the roof PT ee 4 Mount the monitor with the provided hardware
3. sharp edges created during drilling This will protect the wire from being nicked and causing a short circuit e 3 When connecting the ground lead fasten the ground lead black securely to r a clean metal plate on the vehicle 1 Always use new batteries when replacing the old 2 Do not attempt to charge short circuit disassemble heat or burn used batteries 3 Battery replacementis necessary when remote control acts sporadically or stops operating this device 4 Do not place objects between the remote control andremote receiver 5 1f the Monitor does not operate even when operating the remote control from a close range itis time to replace the batteries Battery type CY2025 Video input 1 fei RCA I m Audio input left White RCA rl mo INSTALLATION The device is an overhead fold down 19 inch monitor with an IR Infrared eye Audio input right Red RCA mg Di Video input 2 yellow ii It will accept 2 video signal from any video sources with composite video out 1 Look over the vehicle for a location for the monitor Each vehicle is different and locations will vary Make sure the monitor will not interfere with the Driver 1 2 once a location has been determined connect the IR A V RCAs and IR wireless headphone Optional Pa Audio R gt Power cables to the designated sources 3 Feed the cables through the hole inthe mounting bracket and screw the
4. e normal for liquid crystal product Front panel 7 123456 Contents and specifications can be subject to change without prior notice SPECIFICATIONS SCreeN size re i Display Methodo esetere Poredi si ersa Power supplyt e e tedi se to ph mitt ei Power consumption ece cs cs ss ee ee te oms ACCESSORIES Metal mounting plate Instruction manual 19inch PAL amp NTSC TFT Active matrixsystem 16 10 1240x800 DC 12V 10 34W 3900g Remote control Mounting screws IR headphone Optional 1 IR Sensor 2 Power on off 3 MENU Brightness Contrast Saturation Language Source Reset Exit 4 Negative adjustment 5 Positive adjustment 6 V1 V2 switch 7 Monitor release button Press torelease the monitor 8 Dome light REMOTE CONTROL 2 3 4 5 3 1 Power Press to Power On Off the monitor 2 Video select V1 V2 switch 3 lt Press to decrease the value gt Press to increase the value 4 Menu Press to active the OSD menu it shows Brightness Contrast Saturation Language Source Reset Exit 5 Image switch 16 10 or 4 3 Some functions only available if the device connected with the optional components WIRING REMOTE CONTROL BATTERY Read all wiring precautions If you are not sure of the connections contact your authorized dealer 1 Disconnect the negative lead of the battery before making any power connections 2 When creating passage holes for the power wires use grommets to eliminate any
Download Pdf Manuals
Related Search